Search Documents

GENERALTHE coal deposit, where it is being worked, consists of a bed of brown coal varying in thickness from 120 ft. to 200 ft., covered by an overburden of clay, drift, loam, etc., of a thickness of 22 ft. to 40 ft., and averaging 28 ft.The overburden is first entirely removed from the coal, and then the coal is excavated by. large revolving shovels which work at the bottom of the hole or open cut in the coal and deliver it in shovel bucketfuls to the transport system. The shovels owned by the Commission and available for this coal excavation are two Bucyrus steam revolving shovels, one being type 150B, weighing 150 tons, having a 21-cub. yd. bucket, and capable of digging a 47-ft. face; and the other being type 175B, weighing200 tons, having a 31-cub. yd. bucket, and capable of digging a 61-ft. face.In addition to these two steam shovels, the Commission has recently obtained a No. 250 Ruston electric revolving shovel weighing 340 tons, and having a bucket of 10 cub. yd. capacity, and capable of digging a 75-ft. face. When this electric shovel has been erected it will replace the steam shovels on the coal excavation, and the permanent transport system has been designed to take delivery of the coal from its bucket.The duty to be performed by the transport system is to take the coal from the shovels, elevate it out of the open cut, transport it to the screening house, deliver it iuto the hoppers at the top of this building, then to take the coal after it has passed over the screens and distribute the required grades to the power house and to the briquetting plant.

Jan 1, 1924

Mount Read is 'situated in the county of Montagu, on 'the west coast of Tasmania, about 20 miles inland from. Remine in an easterly direction, 15 miles northerly from Mount. Lyell, and 30 miles south-east from Mount Bischoff, and is one of the mountains forming the west coast range; it rises to a height of 3890 ft. above sea level.About eleven years ago the first mineral section was taken up on Mount Read by a Hobart company, known as the Mount Reid Silver Mining Company, consisting of 25,000 shares its holding consisted of one section of 80 acres, held under mineral lease. Prospecting was carried on for some months under great disadvantages, as all supplies had to be carried up the mount from Dundas, a distance of nine miles, on men's backs, until a pack track for horses was made.The track rises 2500 ft. in the first five miles, and then falls 200 ft. from that point to the mines, which are at an altitude of 3000 ft. above sea level, and at a point about two miles westward from the summit of the mountain, approximately midway between Mounts Read and Dundas.

Jan 1, 1901

The copper-clay deposits consist largely of goethite and clayey mudstones carrying native copper, cuprite, and chalcocite. The mudstones are of Ordovician age, are interbedded with Fe-Mn carbonates, and probably contained syngenetic iron and copper sulphides. The secondary copper minerals have been derived from post-Devonian weathering in situ and also by deposition from surfaee and underground waters draining the adjacent mineralized volcanic rocks.

Jan 1, 1969

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this interesting subject. In the up of the electrical arrangements touched on in this paper, the author has had the able assistance of his friend Mr. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer is better than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant. Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of before it is possible to arrive at a proper decision.

Jan 1, 1912

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By Patrick J. Doig

In mid-1991, the design/build contractor set to work on the Pergau HEP in a remote corner of Malaysia, armed with only a slim volume of conceptual drawings. The next five years saw roads, power lines, buildings, dams, and over 30 kilometers of tunnel constructed, followed by two years of E&M installation and commissioning. Along the way, the project overcame geothermal groundwater, faults, land disputes, monsoon rains, marauding tigers, and those most fearsome of foes, politicians and the press. This paper is a testament to the ingenuity, commitment, and persistence of the construction industry professionals who brought this massive project to fruition.

Jan 1, 2001

In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned. A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view

Sep 1, 2004

By H. D. Mellom

The direction of the optic or "C" axis of a uniaxial metal crystal can be found with the metallurgical polarizing microscope by examining two planes of section on the crystal. Complete orientation of the crystal can be determined if a twin crystal is common to both surfaces of section. Examination of Uniaxial Metals in Polarized Light-Rotation of a uniaxial crystal surface, properly prepared,' shows four extinction positions 90 deg apart, provided that the surface is not close to a basal section. One of these two extinction directions corresponds with the projection of the optic axis on the surface of section. This direction can be found if the 'sign of the rotationr2 for the metal is known. To find the direction of the optic axis, the crystal is rotated on the stage 45 deg from an extinction position. With a crystal of negative sign, to produce extinction the analyser must be rotated towards the optic axial direction and vice versa. All sections, other than basal, of a uniaxial crystal have the same sign of rotation and, since there is no change in sign with wave length, white light can be used for these measurements. U the sign of the rotation is not known the presumed direction of the optic axis can be determined assuming a positive sign. A third section cut normal to the presumed optic axis will show basal extinction if the assumption is correct. It is convenient to use the edge between the two planes of section as a fiducial direction common to both surfaces. The optic axis can be related to this direction. If the above measurements are repeated on the other plane of section and the angle between the two section planes measured, stereographic projection can be used to determine the orientation of the crystal optic axis. Determination of Complete Orientation—The complete orientation of a uniaxial crystal can be determined provided that a twin crystal is common to both surfaces of section, and the twin law is known. The orientation of the twin crystal optic axis can be determined in the same way as for the main crystal

Jan 1, 1962

LAKE MARGARET is situate high up on the West Coast Range of Tasmania, and lies in a roughly triangular valley formed by the ridge of Mount Sedgwick on the south, the ridge formed by Mounts Geikie and Tyndal on the west, amid a ridge connecting Mounts Geikie and Sedgwick on the east. Any description of this hydroelectric installation, however brief, naturally divides itself into the following sections:1. STORAGE BASIN, &c. 2. DAM. 3. PIPE LINES. 4. POWER STATION. 5. TRANSMISSION LINES. 6. SUBSTATION 7. VARIOUS WORKS utilizing the power.The Storage Basin used is the natural lake itself, which has a maximum length of 110 chains, a maximum width of 40 chains, and a mean arelj. of 300 acres. The water-level of the lake, which has been maintained by a natural dam, is 2143 ft. above sea-level. The approximate catchment area at present appropriated is 7 sq. miles, and the rainfall, on the average, about 144 in. per annum. It is possible to increase this catchment area by suitable races, &c. Dam.-The dam constructed is of very small dimensions, and is not a storage dam in the usual sense of the term. The natural storage ot-the lake itself was used by means of a channel cut through the natural dam and thence to the mouth of the lake, the lake level being thus temporarily lowered while the outlet pipes, screens, &c., were placed in position, and the channel was then closed again with a concrete wall in which the pipes and screens are set. This channel was cut partly through rock and partly through sand and conglomerate boulders for a total...

Jan 1, 1915

By O. P. Garg

"The Iron Ore Company of Canada (IOC) operations in Labrador and Quebec, in Canada, is among the largest openpit mining complexes on a world wide basis. Since the 1981-82 recession, IOC has embarked on a comprehensive cost reduction and productivity improvement program in order to survive in the world iron ore market.This paper will outline the approach used in prioritizing the cost reduction items.IntroductionMuch of the mining industry in North America is in a crisis state. Most producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC) operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectively. A company owned and operated railway links this operation with the dock terminal facilities in Sept-Iles, Quebec.In the past decade the Iron Ore Company of Canada has been one of the largest producers of iron ore products in the world. Its pellets and concentrates as well as natural ores were sold in North America, Europe and the Far East. In 1981-82, sales, particularly in North America, went into a serious decline. For almost 30 years, the gospel IOC preached to employees was ""production, production!"" There were many innovations, and millions of dollars were spent on the biggest and best equipment, on research and development, on training and developing employees."

Jan 1, 1987

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By L. F. Elkins

Water coming into wells with bottom water present in the Fosterton field, when their oil recovery was only 0.1 to 1.5 per cent of oil in place below the lowest perforation, confirms lack of shale barriers to vertical flow which also are not apparent in cores and electric logy. Low contrast of vertical and horizontal permeability, high mobility ratio betweerz oil and water zone and pos.rible rate effects due to gravity Combine to prevent easy analysis of water invasion pattern and efficiency by analogy or intuition. Theoretical analysis of performance including these factors using a new direct nurnerical .solution of potential distribution in a network led to unanticapted indications that water would under-run the entire oil reservoir with low volumetric coverage if supplied through natural influx or peripheral water injecfion below the oil-water contact. An unusual pattern of water injection is to he adopted in this recently unitized pool to provide more uniform water flooding in that two-thirds of the oil reservoir not underlain by bottom wafer. INTRODUCTION The Fosterton field, Southwestern Saskatchewan, Canada, was discovered in Jan., 1952. It produces at a depth of 3,100 ft from a pinch-out of the Roseray sand at the Lower Cretaceous-Jurassic unconformity. The field, covering 2,500 acres, contains 54 wells on 40-acre spacing. Development was essentially complete in June, 1954, but significant production did not start until May, 1955, when a pipeline outlet became available. Within one year rapid in- creases in gas-oil ratio and early encroachment of water created operating problems in the down-structure eastern half of the field and raised serious questions about reservoir performance and ultimate recovery. This paper describes the unusual behavior of water encroachment—on both well and reservoir bases—and the analyses made to interpret it. The field was unitized July 1, 1958, for water flooding. A somewhat unconventional

By J. S. Miller

This report presents a complete coverage of results from Bureau of Mines preliminary research and the field application of explosive fracturing techniques to prepare oil shale for in situ recovery of shale oil. Small-scale surface tests were conducted to determine the feasibility of using a nitroglycerin-base explosive for creating rock fractures. Prior to underground testing, surface and near-surface tests with liquid explosives showed that explosions in sheetlike layers simulating underground fractures would propagate effectively. Successful surface experiments were conducted using layers of explosive placed between glass plates and explosive-saturated sand confined in small-diameter metal tubes. The tests in glass-plate reservoirs and metal tubes demonstrated that nitroglycerin would detonate and the explosion would propagate in cracks as thin as 1/32 inch and through distances up to 12 feet. In a shallow field test, nitroglycerin was detonated in a vertical crack in limestone and produced extensive fracturing. Explosive fracturing tests were performed in oil shale formations on seven sites near Rock Springs, Wyo. The procedures included (1) displacing and detonating nitroglycerin in natural or hydraulically induced fracture systems; (2) detonating nitroglycerin in wellbore shots; (3) displacing and detonating nitroglycerin in induced fractures followed by wellbore shots using pelletized TNT; and (4) detonating wellbore charges using pelletized TNT. The research on oil shale formations demonstrated that nitroglycerin displaced in a natural or hydraulically induced fracture would detonate, and the explosion would propagate through the explosive-filled fracture. Shooting a pattern of wells in oil shale at 100-foot depth with wellbore charges of pelletized TNT developed a satisfactory interwell fragmented zone. Tests performed on other sites at depths to 385 feet caused fragmentation of rock around the wellbore and provided interwell communication. Fourteen methods used to evaluate the extent and degree of fragmentation in the explosive fractured oil shale are discussed.

Jan 1, 1974

Interest in the tantalum-niobium minerals has been greatly stimulated in Western Australia by the fact that these rare minerals occur at numerous localities in that State, and in the adjoining parts of the Northern Territory, sometimes in mineable concentrations, as at Wodgina and Greenbushes. A large proportion of the world's tantalum comes from these deposits. The late Dr. E. S. Simpson, in particular, made an extensive study of the chemistry and mineralogy of these minerals, and the following observations are based upon the examination of specimens which he and Mr. H. Bawley, Government Mineralogist of Western Australia, have submitted to me for examination from time to time. The fact that so many of the specimens have been analysed provides a unique opportunity for the interpretation of the phenomena observed in the polished sections.TANTALITE-COLUMBITE SERIESIt has long been considered, on the basis of crystallographic form, chemical analyses, and specific gravity measurements, that ferrotantalite (FeO. Taz05), manganotantalite (MnO. Taz05)' ferrocolumbite (FeO. Nbz0 5), and manganocolumbite (MnO. Nbz0 5 ) form a complete isomorphous solid solution series (Simpson, 1937) and this is confirmed by study of polished sections of these minerals, Pehrman (1929) examined a series of five analysed specimens with Nbz0 5 contents as follows:-

Jan 1, 1940

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By J. R. Piper

“Old Borate,” located in the Calico Mountains east of Barstow, California, lead domestic colemanite production from 1884 through 1907. Mineral exploration at “Old Borate” in the early 1980's, examined borate mineralization in Tertiary lacustrine strata. Surface sample and drill hole locations, geology and structure, were hand-drafted on paper maps. To re-evaluate this data, the information was digitized using Geographic Information Systems software. Digital Elevation Model based terrain modeling integrated surficial samples with drill hole data to locate favorable drilling targets. Structural relationships were used to identify hypothetical resources formed by the leaching of boron from surface exposures, redeposited at depth.

Jan 1, 2001

By Johnston W. H

MINING operations in the Waihi mine began, under the present proprietorship in the year 1889. Previous to this, and as far back as the year 1880, the presence of reefs in the Martha Hill had been known, and surface working on a small scale had beencarried out, without any great measure of success. The only method of treatment in use at this time was the old system of light stamps, amalgamating tables and berdans, and recovery by this method being low, little margin for profit was left, so thatthe property in these days was not considered of great importance and work on the area was only carried on spasmodically by different owners.On the transfer of the leases to the present company, calcining, dry crushing, and hot pan amalgamation was adopted as the method of treatment, and this system was continued till the more modern cyanide process was introduced and applied. As themethods of treatment and gold-saving became more efficient with the application of more modern and scientific processes, the importance and future prospects of the mine became more and more pronounced, and mining on a larger and more comprehensive scale was gradually established.As in the case of ore treatment, mining methods in the early stages were not as far adv.anced as the adopted practice of today, and numerous shafts, levels close together in vertical height.

Jan 1, 1912

By John Meuth, Brandon Fryman, P. E. Hoffman, Joshua Ph. D., P. E. Calnan, Josh Ph. D.

Quantitative Risk Assessment (QRA) can be specifically tailored for use by the commercial explosives industry to calculate risk to employees and the public from commercial explosives facilities and operations. This methodology has several advantages over the American Table of Distances (ATD) which is solely a Quantity Distance (Q/D) analysis. While the ATD has remained essentially the same for 100 years, the safety of commercial explosives in storage has increased immensely. However, the concepts behind QRA calculations are not as intuitive and even at the end of the calculations the values of risk must be compared to something. A few regimes for assessing an acceptable level of risk are discussed in this paper. Risk levels for various United States Federal entities and international agencies are highlighted and suggestions for acceptable risk criteria for individuals and groups are provided. Referencing risk levels from normal daily activities is also done in this paper to make relative the accepted risk criteria. This paper presents some relevant individual risks for everyday activities and some scenarios for group risk for comparison. Individual risk is a straightforward concept however group risk is more complicated. This paper aims to clarify these concepts and provide means to communicate them to the public.

Jan 1, 2019

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, Mexico, 150 km (95 miles) southwest of Ciudad Juarez (Fig.1). The ore deposit was discovered in 1979 and was placed in production in 1992. The production rate is about 2.4 kt/d (2650 stpd) from an ore reserve of 8.5 Mt (9.3 million st). Grades currently average about 8% zinc, 0.5% lead, 0.2% copper and 50 g/t (1.46 oz/st) silver. Substantial inflows of water into the underground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark is a joint venture with 90% participation by Minas Penoles, SA de CR of Mexico City and 10% participation by Promociones Industriales Banamex, S A de C V (PIB S A) of Mexico City. Anew company, Minera Bismark, SA de CV was formed to operate the property. Cyprus Minerals was a 40% participant in the joint venture but, in early 1993, sold its share to Minas Penoles. The Bismark Mine is one of the largest new underground mining projects built in Mexico during the last 10 years. It is the country's fifth largest underground metal mine and provides about 1 % of the world's zinc supply at about 50 t/a (55,000 stpy). Bismark is a trackless operation with overall productivities of 7.6 t/manshift (8.4 st/manshift). The 2.4-kt/d (2650-stpd) concentrator started up in March 1992.

Jan 1, 1994

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970