Search Documents

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

By John Carr

The tremendous growth in grinding mill size and horsepower during the '70s demanded advancements in gear cutting technology and equipment for the '80s. Computers are used as an aid in the design and selection of the mill drive system; sophisticated computer graphics are used to create manufacturing drawings; and a new generation of gear cutting machines are used to manufacture the gears. These new gear cutters can generate-cut gears over 40' (12.2 m) in diameter at an AGMA quality level exceeding the currenty acceptable standards. The precision of the resulting gear assures maximum tooth contact, which will result in longer gear set life.

Jan 1, 1981

By Shamim A. Dar, & Samsuddin Khan, & K. F. Khan, Mohd Shuaib

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.

By Grant E. Casley

Since 1970 Mount Isa fines Limited has made a significant increase in blister copper production from approximately 100,000 to 155,000 mt per annum and in fact 161,040 mt were produced in the calendar year 1974. Flowsheet developments including fluidised bed roasting and converter slag flotation are discussed, particularly their contributions to minimising major equipment changes in smelting and converting. The use of model- ling and simulation techniques for such an exercise is mentioned. The paper reports the alterations made to both equipment and operating techniques in the reverberatory furnace and converter sections to achieve the regular production of 250 mt of blister per converter day from a 41% Cu matte grade. The effects of flux composition on converting performance are highlighted. The air quality control programme is discussed in relation to its restriction of blister copper production.

Jan 1, 1976

By R. E. Hucko

The principal thrust of the U.S. Department of Energy (DOE) Coal Preparation R&D Program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. Specifically, the objective is to develop and refine cost-effective physical and chemical beneficiation processes to extract 85-95 percent of the total sulfur and ash. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas -coal characterization, beneficiation, and ancillary unit operations. This paper will provide a brief overview of many of the research projects being carried out in these areas in fiscal year 1984.

Jan 1, 1984

By John V. Beall

The mining industry of Japan is not very large, but it is very old. Some of the mines have 1000 years of history. At Nara, the capitol 1300 years ago, the great Buddha of bronze that was cast at that time was of metal mined from several localities in Japan including the Akenobe-Ikuno district, one of the present Mitsubishi properties. Methods of smelting copper and iron, it is believed, came from China via Korea. A characteristic of the Japanese mining industry today is one of buying abroad and treating at home, a variety of ores of different compositions. All in all, Japan's mineral deposits under its own flag are inadequate for its great industrial strengths.

Jan 5, 1969

The ability to increase and maintain dragline productivity is a key mine driver for the Coal Creek Mine. The Coal Creek Mine is owned by Arch Coal Inc subsidiary Thunder Basin Coal Company; located near Gillette, WY. Coal Creek Mine overburden stripping is primarily accomplished by a BE-1570W walking dragline in combination with cast blasting and dozer assist for bench preparation. The two main variables impacting dragline performance are maintenance reliability and operator skill levels. The mine?s most recent process improvement efforts have focused on its most valuable asset - the operator. Various techniques have been used to reduce variability in the dragline operator?s digging performance. Utilization and communication of operator performance data, statistics, and video reviews have been of great value towards achieving this goal. Operators are given a chance to critique operational tendencies from a third-person point of view, and are also presented statistical feedback to support observations. From these sessions, operators gain knowledge as to what portions of the dig cycle can be improved in order to reduce cycle time and increase productivity. BACKGROUND The BE-1570W walking dragline was commissioned at Coal Creek in November 2006 after relocating from Arch of Wyoming located in southeast Wyoming. The first two years of operation the machine was performing simple side cast stripping due to the low ratio. Coal Creek Mine is a multiple seam operation with overburden thickness ranging from 24 to 140 feet. Early in 2009 the ratio increased to the point where transitioning to cast blast/extended bench stripping was necessary. The current mining conditions consist of a mixture of both stripping styles where the ratio allows. The dragline crews running the machine consist of a mixture of experience levels ranging from 30+ years to only a few years. It has been in this digging environment and slightly inexperienced personnel that the focus has been set for improvement in dragline performance.

Jan 1, 2011

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By Richard A. Hawkins

O the American coal man, Australian coal mining most appear to have little, if any, influence on American coal-mining practice and to bear little relation to it. Actually, the relationship has been close, for Australian operators have carefully studied American practice by reading American technical publications, by consulting American engineers, and by visits to Ameriean operations. They have leaned heavily on America for their supply of mechanization equipment and many American mining-machinery manufacturers are active in that country, supplying its needs and furnishing technical assistance. Australia's influence on American coal mining has been obscure and probably negligible. However, it seems reasonable to assume that this influence will increase. The wartime development of air transportation will inevitably bring these two countries into much more intimate contact than existed in recent years. American servicemen. many of them former miners and coal-mining technicians, have visited Australian operation, while stationed in that country, have talked with operators and men over there, and undoubt-

Jan 1, 1945

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By I. Ashmole

The dimension stone industry is not widely known or appreciated within the mainstream mining industry. This is in spite of the fact that the industry has grown at an average of over 7% per annum since 1980, and is estimated to now have a global turnover in excess of US$ 60 Billion per annum. Production technologies, particularly in the developed world where labour costs are high, have developed rapidly over the past two decades. Aligned with this, there has been a significant trend in adoption of a more professional mining approach in the exploration for and operation of dimension stone quarries. In fact, in the experience of the authors, mining a dimension stone deposit successfully if often more challenging from a mining engineering point of view than many conventional surface mines. This paper gives an overview of the industry and then proceeds to discuss best practice in exploration for dimension stone and to outline the latest technologies applied in mining of dimension stone. These technologies are varied and the specific combination of technologies applied in any given quarry is determined by both the physical properties of the material as well as the influence of geology which significantly impacts on the recovery of saleable material and hence the economics of the quarry.

Jan 1, 2008

By Tim Lundquist

Disa Technologies Inc. provides innovative, sustainable solutions for mineral processing and remediation through its patented High-Pressure Slurry Ablation (HPSA) technology. HPSA processes solid feed material in slurry form, propelled by high pressure pumps through opposing nozzles that generate impinging jets within a collision housing. This process induces particle-to-particle collisions in a high energy zone, creating intergranular fractures along grain boundaries. In our batch scale and continuous operating testing, we have found that controlling key processing variables such as nozzle velocity, slurry solids percentage, and the number of passes can allow for controlled size reduction and maximum mineral liberation. Since 2018, Disa Technologies has demonstrated the versatility of HPSA by testing it on diverse materials, including phosphate, copper, uranium, vanadium, zinc, rare earth elements, lithium, nickel, mineral sands, gold tailings, and more. The intent of this paper is to present an overview of our test results describing in detail impacts on size reduction, recovery, and grade with a focus on HPSA's adaptability across ore types. Looking forward, it explores the potential to process materials such as DR-grade iron, clay, PGMs, bauxite, and various tailings. Additionally, it examines planned advancements in HPSA technology, including optimized nozzle spacing, higher capacity models, improved tonnage-to-footprint ratios, enhanced maintenance features, and expanded nozzle configurations.

Jan 1, 2025

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By Jorge Madias

A Aceros Arequipa é a maior siderúrgica do Peru. A empresa opera uma planta em Pisco, com uma aciaria para 850.000 t anuais de aço líquido, e uma capacidade de laminação de 1.250.000 t anuais de produtos longos. Um projeto de integração vertical incluindo coqueria non-recovery, sinterização e alto-forno foi considerado. Como parte do projeto, um forno piloto de coqueificação foi instalado, com o intuito de testar carvões próprios e importados e obter a máxima participação de carvão local nas misturas. Foram testados sez carvões peruanos e antracito. Os carvões importados escolhidos foram três da Colômbia e quatro dos Estados Unidos. Levando em conta as baixas propriedades dos carvões próprios, foi introduzida a estampagem da carga. A máxima participação dos carvões locais, mantendo a qualidade requerida, foi obtida com 80% de carvão peruano, e 20% de um carvão columbiano. Pode-se usar até 10% de antracito, junto a 60% de carvão peruano e 30% de carvão colombiano.

Oct 30, 2017

By Michael J. McGuire

Rostoker, Inc. has developed a process to smelt solid hazardous/non-hazardous inorganic wastes. Near seven hundred experiments were performed. Actual industrial wastes as well as reagent grade chemicals were used. By mixing a multiplicity of these wastes to proper formulations, then furnacing them, it was determined that saleable end products could be reclaimed; metal, fume and slag. The slag, due to its siliceous structure was tested to be leach resistant (40 CFR). This formed the essence of our patent, #5,180,421 "Method and Apparatus for Recovering Useful Products from Waste Streams". What is unique is that a HTMR (High Temperature Metal Recovery) process has been developed that can treat a multiplicity of wastes within the same furnace. The discussion will include a list of waste streams we have treated, details of proper waste formulation and experimental results.

Jan 1, 1994

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Maycon Athayde

O processo de pelotização consiste na aglomeração e posterior tratamento térmico das pelotas, ajustando as propriedades químicas e mecânicas para o transporte ao reator siderúrgico. A otimização e aperfeiçoamento do processo no forno pode ser realizado experimentalmente utilizando um pot grate. Trata-se de um equipamento no qual uma carga de pelotas cruas é submetida a condições similares às encontradas no processo industrial. Contudo, um projeto de experimentos em um pot grate pode levar semanas. Além disso, alguns parâmetros como: taxas das reações e balanço de energia são difíceis de serem monitorados. Tendo em vista isso, o presente trabalho buscou desenvolver um software de simulação para avaliar o comportamento das pelotas em um pot grate de maneira rápida e prática. Os resultados mostram uma interface amigável para a avaliação da temperatura de pelota, umidade da água, queima do carbono e balanço de energia. Os modelos implementados foram comparados e validados com trabalhos publicados na literatura. O modelo também serve como uma ferramenta de Projetos e Experimentos no Pot, uma vez que permite testes mais rápidos e de custo mais baixo.

Aug 16, 2017

By S. Covaci

El presente texto señala el método adecuado para el enfoque de investigación del futuro en la minería. Para ello, es necesario obtener la tendencia simultánea del desarrollo de la industria y educación de la minería; el discernimiento "general" de los posibles futuros, y la posibilidad en mayor extensión de desprenderse del pasado. De forma que es necesario, la realización de una encuesta de tipo Delphi entre un grupo de especialistas rumanos de la industria minera.

Mar 1, 1981

By Jian Liu

The study aims to leach copper from a low-grade flotation middling by optimizing the leaching process using response surface methodology. The effect of key parameters, i.e., sulfuric acid concentration, nitric acid concentration and leaching time, on the leaching efficiency was investigated and a quadratic model was suggested by the methodology to correlate the variables to the efficiency. The results indicate that the model is in good agreement with the experimental data at a correlation coefficient (R2) of 0.97 and the most influential parameter on efficiency was identified as sulfuric acid concentration. The optimum conditions for copper leaching from the middling were identified as sulfuric acid concentration at 103.74 g/L, nitric acid concentration at 12.50 g/L and leaching time of 30.98 min; under such a condition, an average leaching efficiency of 93.16% was achieved from the middling.

Jan 1, 2011