Search Documents

By Louis R. Bernier

Since 1978, most systematic studies of AMD passive treatment with limestone drains (LD) have dealt with coal mines in the United States. The authors present in this paper the first results of a triennial study initiated in 1999 on the performance of LD installed at the Ni-Cu Lorraine old mine site in Temiscamingue during a remediation plan that involved the installation of a cover with capillary barrier effects (CCBE) over the reactive pyrrhotite-rich tailings. Typically, a LD is a trench enclosed by impervious materials filled with crushed limestone and may be oxic or anoxic. Four LD (one filled with marble and 3 with dolomite) were installed at the Lorraine site. The LD have been in operation since May 1999 and are performing differently. The most contaminated mine effluent flows south and is directed towards 3 LD filled with crushed dolomite, while a 4th LD was filled with crushed marble and installed west. The LD filled with marble has been generating maximum alkalinity since the beginning of the passive treatment. Two of the dolomite drains have been generating alkalinity since mid-summer 1999, but one is not, even if a substantial pH raise was observed. A pH above 5.5 is required usually for the dolomite drains to start generating alkalinity. The installation of LD at the Lorraine site contributes significantly to the reduction of metals and sulphates loading.

May 1, 2001

By G. W. Smith

"The adsorption of dehydroabietylamine acetate on quartz, hematite, rutile and baddeleyite has been deter-mined for concentrations ranging from 0.3 to 5,600 µ. moles/I and for pH values ranging from 2.5 to 10.5.The surface tension, UV and IR spectra, equivalent conductance and ion concentrations for dehydroabiety lamine acetate solutions have been determined.Contact-angle and flotability studies have established that good collection may be obtained with this amine but that selectivity depends on the suitable use of depressants for some of the minerals."

Jan 1, 1971

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By Kent Phillips, Meredith Scaggs-Witte, Emily Sarver, Cigden Keles

"After nearly four decades of decline, the prevalence of coal workers’ pneumoconiosis (CWP, or black lung) in the United States has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of rapidly progressive disease such as progressive massive fibrosis (PMF) (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 U.S. coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85 percent) that had a normal radiograph on file to use as a baseline, 27 (17 percent) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84 percent) of the individuals in that study worked in Kentucky, West Virginia or Virginia, and 169 (88 percent) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern Kentucky. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, there has been some concern that these reports may overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression — such that effective interventions can be devised.The notable uptick in CWP and PMF rates among miners in central Appalachia has led to this region being called a hot spot for disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2014; Laney et al., 2017). While the geographic clustering has been well documented (Pollock et al., 2010; Antao et al., 2005; Wade et al., 2011; Wang et al., 2013), the root cause is still unknown. Leading hypotheses have focused on the relative amount of rock being cut along with coal in many central Appalachian mines, as there has been a tendency to mine increasingly thinner coal seams over the past couple of decades (Laney et al., 2010; Schatzel, 2009). This shift has likely been accompanied by changes in specific dust exposure factors, such as increased abundance of particularly harmful dust constituents (e.g., silica or silicates) or increased frequency of harmful exposures (e.g., due to work in more risky environments) (Pollock et al., 2010; Blackley et al., 2016; Cohen et al., 2016; Douglas et al., 1986)."

Jan 5, 2018

By Walter J. Frank

The purpose of the work covered by this contract is to develop a means of designing splice connectors which will significantly improve mine trailing cable splice performance. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. Because of the empirical nature of this effort, time has been devoted to explaining the derivations of the test procedures used. Special attention is given to the splice flexing machine which served as the backbone of the test program. In order to familiarize persons with connector terminology, a section is devoted to a glossary of pertinent terms. Various types of cable joints are also defined. The major effort is a connector design parameter study. Utilizing the optimum parameters developed along with the suggested design procedure outlined in Appendix I should result in significantly improved splice performance and thus meet the objectives of this contract. A field test program was instituted for the purpose of insuring adaptability of connector design and associated installation tooling along with a field performance study. During the course of work, other significant factors affecting splice performance were uncovered. Although not covered by the scope of this contract, a brief discussion is presented for the purpose of stimulating interest in what is considered other fruitful areas for improved splice performance.

Jan 1, 1976

By John J. Dran

[This paper summarizes the more popular mineral valuation techniques being used by the dining industry, and attempts to demonstrate how they are Interrelated and where some are in error when compared to modern methods of financial analysis. The academic community and the larger and more sophisticated raining companies, have largely rejected the older valuation methods such as the, Hoskold and Morkill concepts and replaced them with "discounted cash flow" (DCF) techniques. The relevancy and usefulness of the older methods have been questioned primarily on the basis of their underlying assumptions that mining companies do not have numerous alternative investments and must use sinking funds deposited at market or ?safe" rates of return to recover the purchase price of mineral reserves. The ability to reinvest In numerous (often non-mining} alternative business ventures, the changing purchasing power of the dollar, corporate income and other taxes, depreciation and depletion allowances, and modern financial management practice, all mitigate against the continued use of the older valuation methods, especially for the larger mining companies. Snail mining companies and Individuals still use these methods largely out of habit and familiarity. This paper attempts to point out the weaknesses and strengths of the valuation methods In current use in the hope that these techniques may be better understood and [rcrn] appropriately applied.]

Jan 1, 1973

By Michael Hamilton

Mineral resources have been identified at two properties in the Ten takes RARE II area (table 1). Commodities consist of copper and silver. The deposits, in the northwest part of the study area, are hydrothermal and associated with fissure veins that developed along northwest-striking faults within the Precambrian Purcell Lava. In addition to the identified resources, there is high potential for additional copper-silver resources at these properties and moderate potential for copper-silver-lead-zinc-bariun resources at five others (table 2) in the portion of the study area that is underlain by the Purcell. There is no evidence that significant mineralization occurred in strata above or below the Purcell.

Jan 1, 1983

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By Lucas Teixeira Costa

Um modelo matemático foi criado para simular a dessulfuração do aço no desgaseificador RH na condição de uma camada de escória sobrenadante adicionada dentro da câmara de vácuo após a subida do aço sob efeito da pressão. Tomou-se como base o modelo físico do LaSiP (Laboratório de Simulação de Processos) em escala 1:5 para a instalação industrial de uma usina brasileira. A validação do modelo foi realizada por meio da taxa de circulação do modelo físico e de sua simulação. A dessulfuração do aço foi realizada pelo modelo matemático para as condições operacionais da indústria e a avaliação de parâmetros como composição química e volume de escória foram investigadas. Ao final, obteve-se resultados compatíveis com os presentes na literatura e um modelo capaz de prever com grande confiabilidade a evolução do teor de enxofre ao longo do processo de dessulfuração. Considera-se, portanto que a prática de remoção de enxofre no RH é viável e tem-se uma rota adicional/alternativa ao forno panela.

Aug 16, 2017

By José Fernandes De Oliveira

La fabricación de filtros para la industria minera requiere del conocimiento de los minerales que están siendo procesados en una determinada planta de beneficio del mineral. En ese sentido, las propiedades de las partículas que serán sometidas al proceso de filtraje, como la dureza, morfología, tamaño y composición son importantes en la selección del tipo de material que será empleado en el diseño de las zarandas. Por ello, el presente trabajo señala los parámetros de las propiedades de la partículas: composición mineralógica, morfología y tamaño de los granos presentes a través del estudio por microscopia electrónica de barrido cinco muestras de filtro.

Sep 12, 2011

By J. Méndez-Nonell

The thermodynamic and chemical properties of SrSO4 and SrS in a gaseous flow of CO and CO2 at high temperature are discussed. The thermodynamic analysis of the system was made using data from the literature. The results obtained from the thermodynamic analysis were experimentally verified using the thermogravimetric technique. The experimental results suggest the formation of a complex compound between SrO and SrSO4. It was also found a change in the chemical mechanism of the process between SrSO4 and CO-CO2 and in the chemical mechanism of the process between SrS and pure CO2.

Jan 1, 1995

By Ricardo Thomé da Cruz

O conhecimento sobre o comportamento do revestimento refratário dolomítico durante a etapa do refino de aço é fundamental para se atender às exigências técnicas de qualidade e o aumento da produção de aço. É particularmente importante que os mecanismos de corrosão dos refratários dolomíticos sejam bem compreendidos, principalmente, em operações de exceção, nas quais as exigências metalúrgicas causem forte dano ao revestimento, prejudicando não somente o desempenho do mesmo, mas também gerando um risco à segurança operacional. Este trabalho visa à caracterização técnica da camada protetora (coating) de silicato dicálcico (C2S), a qual se origina da reação entre as escórias silicosas e os refratários dolomíticos. As amostras de coating foram caracterizadas quanto à composição química, fases formadas e microestrutura. Estudou-se uma panela retirada de operação, por dano aos refratários, retirando-se amostras de diferentes regiões. Em duas amostras, juntamente com o C2S e o periclásio, foi observado à presença de fases à base de silicato de baixa fusibilidade como a cuspidina, indicando que o coating foi atacado por uma escória com elevado teor de fluorita.

Jul 30, 2018

By Onuralp Yücel, Kağan Benzeşik, Ömür Can Odabaş, Selçuk Kan

Extraction and processing constitute an important area in the metallurgy of molybdenum. Molybdenum trioxide (MoO3) production is one of the most important stages in molybdenum production. In this study, the effects of different furnace types on MoO3 production were investigated by using molybdenum concentrate as a raw material obtained during the enrichment of copper ores. Preliminary experiments have been made using a chamber type furnace, and a transition to a pilot-scale has been carried out with rotary kiln experiments. The effects of a different time and atmospheric conditions on MoO3 roasting kinetics were investigated by experimental studies conducted in the temperature range of 500–650°C. It was determined that the optimum temperature and time for sulfur (S) removal was 625°C and 180 min in the studies carried out in the rotary kiln, and it was determined that 0.61%S content was reached with an average removal efficiency of 98%. The activation energy in these sets was calculated as 89.519 kJ/mol.

May 3, 2021

By C. B. Kettering

In the early operations of the Inspiration Consolidated Copper Company, which extended from 1914 to 1926, the ore as mined contained principally sulphide copper minerals, manly chalcocite (Cu2S), This ore was milled in a 20,000-ton concentrator and the copper was recovered as a flotation concentrate which, was smelted at the nearby plant of the I ternational Smelting and Refining Company. In those days no attempt was made torecovercopper from any oxide minerals present. As mining operations progressed it soon became evident that the proportion of oxide minerals present would steadily increase, and. it was realized that some method of treatment would have to be developed whereby copper could' be recovered from both oxide and. sulphide minerals contained in the ore. A research program was instituted and after some years of experimental and, pilot plant work a new hydro-metallurgical process was developed whereby it became possible to extract copper from both the oxide and. sulphide minerals in a single leaching operation. The solvent adopted consisted of a mixture of sulphuric acid and ferric sulphate,' Following dissolution, the dissolved copper would be recovered by electrolysis. Also in the process of electrolyzing, spent solutions of sulphuric acid, H2SO4, and. ferric sulphate, Fe2(SOk)3, would be regeneratede and. somade available for continuous reuse. The process appeared to be a success and the decision was made to build a full-sized leaching plant for the future treatment of I spiration mixed ore. Construction was started and the leaching plant was completed in 1926, With the start of ferric-sulphate leaching the Inspiration Concentrator was shut down and, with the exception of a few short time runs has not operated since that time. The ferric sulphate leaching process served. Inspiration well for some 30 years and during that time won a name for itself as a classic example of hydro-metallurgical treatment of mixed sulphide oxide ores. Originally the plant was designed. to process some 7,500 tons per day of a mixed ore containing about 1,2% copper, of which 60% was present as oxide and. 40% as sulphide, Down through the years various improvements were made for the purpose of increasing plant capacity and as well to change the limiting 'factor of sulphide-oxide ratio, The final result was a leaching capacity of 9,600 tons per day when treating a 1% copper ore with a reversal of the sulphide-oxide ratio to 60% sulphide and 40% oxide.

Jan 1, 1958

By FT Cawood

The latest Draft MPRRB was released for public comment in October 2006. The main purpose of the Bill is to collect royalties at mines developed in terms of new-order mineral rights granted through the MPRDA process. The transition phase stipulated in the MPRDA will be completed by 1 May 2009, on which date mineral royalties will become payable to the state. The royalty rates stated in the MPRRB differ from mineral to mineral and also depend on the degree of refinement. Gold is the subject of this paper, where the royalty rate ranges from 1.5% (for refined gold) to 3% (for unrefined gold) of sales revenue. This royalty is payable regardless of profit, with a maximum 75% relief for loss-making mines. The purpose of this paper is to establish whether or not it would be necessary for gold mines to adjust their mineral reserve statements as a result of this Bill. The methodology is to add the royalty costs stipulated in the MPRRB to the actual quarterly information for the past ten years as reported by the gold-mine members of the COM. The rationale is to investigate the impact this Bill (in its current form) would have had on gold reserves that must be left unmined in the ground because of a higher pay limit. The results of the study point to a significant impact on reserves available for mining with the subsequent shortening of mine lives and retrenchment of workers. Had the MPRRB been effective for the 10 years prior to 1996, it would have resulted in 46 tonnes of gold being sterilised. Stated alternatively, 30 700 workers at COM gold mines alone would have lost their livelihoods.

Jan 1, 2007

The mining of remnant coal reserves at the Liddell Open Cut is subject to a number of risks. These risks are of both a technical and financial nature. Liddell Open Cut is principally a conventional truck and shovel/loader operation, supplemented by a highwall coal augering operation. There are significant areas of divergence from more conventional operations including working in close proximity to a major dam, working up dip from an operating underground mine, and working through areas where there has previously been underground extraction. In addition the site has major long-term rehabilitation requirements. This paper, rather than concentrating on specific detail of areas of risk, presents the spectrum of geological, design, operational and post-mining risks that accrue to the various areas of activity in this open cut operation. The balance of this paper then provides an outline of the strategies employed by Liddell Coal to manage their potential impact.

Jan 1, 1994

Thirty six different commodities were recorded from 3708 mineral occurrences in the Atherton 1:250 000 Sheet area, mapped by personnel of the Queensland Department of Resource Industries. Tin, occurring in 56% of all mineral occurrences, is the most common, followed by copper, tungsten, silver, lead, gold, fluorite molybdenum, zinc and antimony. The densest area of mineral occurrences is the Herberton Mineral Field, one of the most intensively mined areas in the state.The majority of occurrences in the sheet area are fracture, fault or shear related vein or lenticular deposits, with subordinate types being pipe, skarn, endogreisen, disseminated and porphyry copper deposits. However the larger mines in the area are commonly of the subordinate types including the Red Dome gold-copper skarn, the Wolfram Camp and Bamford Hill tungsten- m olydbenum endogreisens, and the Vulcan pipe tin deposit. Significant gold prospects occur in quartz-antimony veins, breccia pipes and skarn deposits associated with rhyolitic porphyry dykes. A fluorite-gold association has been noted in several areas on the western side of the sheet.Mineralised fractures are predominantly oriented in a NNW direction which is the major trend in the Hodgkinson Province. Secondary N and NE directions are also present.

Jan 1, 1990

Jan 1, 1969

By Abhijit Saha

"Two analytical closed-form elastic-rigid-plastic solution methods to predict the rigid foundation behaviour on stone-column reinforced soil are compared, both of which takes into account the stone material yield within the host soil according to stress-dilatancy theory. These are the mechanistic methods developed by the author (2004, 2005) [that presently incorporates the dilatancy angle as per Schanz and Vermeer (1996)] and that developed by Pulko and Majes (2006), that takes into account the column yield as per Rowe dilatancy theory. Since optimal design of stone column necessitates optimum stress concentration on column, which is generally composed of dense gravel with/or without sand, the vertical stress on granular column is often close to its peak strength and the material dilates. To arrive at closed-form analytic solution to this complex soil-stone column interaction problem, some common assumptions like axi-symmetric soilstone column ‘unit-cell’, elastic host soil and rigid-plastic Mohr-Coulomb stone column material are combined with equilibrium and kinematic conditions. The results reflect the beneficial effect of dilatancy within the optimal range or techno-economic domain of area-ratio. The settlement predictions are compared with other analytical methods available in literature as well as with measured settlement reduction of stonecolumn reinforced ground at different subsoil conditions around the globe reported in literature.INTRODUCTIONStone columns or granular piles are frequently used in stabilization of soft clays, silts and loose silty-sands with large amount of fines. The majority of analytical methods assume infinitely wide loaded area with end-bearing columns having constant diameter and spacing that approximate to axi-symmetric conditions, and the approach is known as ‘unit-cell concept’. Several analytical solutions are available, and many of them (Aboshi et al; 1979, Balaam & Booker; 1981) are based on elastic approach considering the stonecolumn and surrounding soil as elastic materials. However, elastic methods give the ratio between the vertical stress in the column to soil (stress concentration factor) approximately equal to the ratio of constrained modulus of both materials. This ratio was found to be considerably higher than measured in the field and it is believed that elastic methods may overestimate the effects of stone columns on settlement reduction (Barksdale & Bachus, 1983). The elastic and elasto-plastic solutions presented by Balaam and Booker (1981, 1985) indicate that the problem can be idealized by assuming that the stone column is in a triaxial state and possibly yielding, such that there is no shear stress at the stone-soil interface and no yielding in the soil. Similar assumptions of stone column to be in a state of limiting equilibrium and under a triaxial stress state are considered in other methods also (Priebe; 1976, Van Impe & De Beer; 1983, Van Impe & Madhav; 1992, Saha & De; 1994, Saha; 2004, 2005, Pulko & Majes; 2006). In majority of the methods it is assumed that under load the stone-column yields at constant volume. However, the last three cases cited consider another parameter; the dilation of stone column. In Van Impe and Madhav’s (1992) and author’s (2004, 2005) method, the dilation is taken into account through the final value of the volumetric strain of column, whereas Pulko & Majes (2006) considered the stone column as Mohr-Coulomb rigid-plastic; dilating at yield in line with Rowe (1962) dilatancy theory."

Jan 1, 2015