Search Documents

By Mimura K

The carbon reduction of tantalum pentoxide was investigated in a plasma-arc furnace. The sample was a mixture of tantalum pentoxide and graphite, vacuum pressed into a briquette and was reduced at about 3100¦C. Argon was used as the are gas. The optimum mixing ratio of carbon and tantalum pentoxide, C/Ta205 is 5.10--5.15. The sample, weighing 7 g is fused within 60^ 70 seconds by plasma-arc heating and the reduction of molten tantalum oxide with solid carbon pro- ceeds rapidly to approximately 99.5 % Ta during this period. The reduction that follows in the molten state is slow. Within about 10 minutes, the maximum tantalum content of the massive metal product reaches 99.9 % and the oxygen and carbon remaining in the product are 50 ppm and 400. 500 ppm respectively.

Jan 1, 1980

By Thainá Silveira Garcia Mendes

A manutenção de monumentos e obras históricas deve ser executada com o uso de argamassa de cal, devido à sua maior permeabilidade e por preservar as características originais da obra. Entretanto, o uso de revestimento de tinta acrílica comercial sobre esta argamassa interfere na permeabilidade da construção como um todo, por vedar a superfície das paredes e tetos, internos e externos. Como uma alternativa que permite maior permeabilidade, tem-se a tinta à base de solo, constituída de água, cola branca e solo rico em silte e argila. O presente trabalho tem como objetivo quantificar e comparar as permeabilidades de amostras de argamassa de cal revestidas com tinta acrílica e com tinta de solo. Usou-se o método do tubo de Karsten para medir a permeabilidade dos dois revestimentos em comparação com a argamassa de cal sem revestimento. Os resultados dos ensaios indicaram que o revestimento de tinta à base de solo apresenta permeabilidade significativamente maior que a acrílica, sendo então mais indicada para o uso em restauro e manutenção de edificações históricas.

Oct 30, 2017

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period 22 November to 10 December 1982. The testing covered herein is for coarse 2-in by 0 (minus 50 mm) Pittsburgh Seam coal in a 6-in (150 mm) pipeline, at velocities ranging from 5 to 20 ft/s (1.5 to 6.1 m/s) and at concentrations ranging from 15 to 45 pct by weight.

Jan 1, 1986

By Elard Miranda, Carlos Lopez

El éxito extractivo en el tratamiento de los minerales auríferos, depende fundamentalmente de su buena caracterización física y metalúrgica, de modo que para un determinado grado de liberación del mineral brinde información acerca de tamaño del elemento valioso y si este se encuentra liberado o incluido en alguna especie mineralógica; del mismo modo debe conocerse el tipo de elemento valioso, si es oro o electrum y los porcentajes de Plata que presenta este último.

Sep 1, 2017

By Chai Li-yuan

Anodizing behaviors of magnesium alloys AZ31 at constant applied current, based on the electrolyte solution free of chromate or fluoride, were investigated. The anodizing process was influenced by constituents of electrolyte greatly. Therein, the oxylate salts, which led to the occurrence of the two totally different processes, played a determinant role in anodizing. They were stable and sparking process respectively. The morphology of anodizing film was observed by SEM and the structure of film was analyzed by XRD. During the stable process, a brown thin film was formed, however the sparking process led to the formation of white hard thick film. The functions of some kinds of additives, such as ammonia, glyceryl alcohol and PVP etc were also studied. Some of them had great effect on surface morphology of anodic film and some of them affected stability of anodizing process significantly.

Jan 1, 2006

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.'s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

By Raphael Lemos

Durante o ano de 2008 foram observados diversos “Gap’s” no processo de lubrificação, tais como: alto consumo de graxa, lubrificação em excesso, degradação de sistemas centralizados, ausência de procedimentos, mão-de-obra sem o conhecimento adequado, entre outros. Dessa forma, o processo de lubrificação foi separado em cinco grandes grupos de atuação, sendo eles: seleção de lubrificantes, gestão do processo de lubrificação, sistemas centralizados, contaminações e vazamentos. Foram aplicadas as ferramentas do MASP (Método de análise e solução de problemas) sendo a primeira delas o "Brainstorming", nos valendo das observações realizadas no Laminador de tiras a quente nº 2. Em sequência foi definido e implantado o plano de ação. Os resultados obtidos após as ações foram: a redução do tempo de parada associada a problemas de lubrificação dos equipamentos do LTQ#2, redução média de consumo de graxa no laminador de - 6.277 kg/mês, quando comparamos a média de consumo do período de Novembro de 2010 a Outubro de 2013, frente ao consumo atual no período de Novembro de 2013 a Outubro de 2014, totalizando uma redução média de aproximadamente - 75.321 kg nos últimos 12 meses.

Aug 16, 2017

By J. R. Rau

While refuge chambers are common place in most underground mining projects, there are different philosophies as to what life support systems are to be considered and how these systems are to be applied. Case studies in the underground mining industry have examples of emergencies where the external compressed air and power supply to the refuge chamber were compromised due to proximity of services to the fire location. In 2005, The Department of Industry and Resources, Western Australia, drafted guidelines that listed specific requirements for refuge chambers which included a secondary life support system that would operate independently of external sources. The objective of this document is to examine what critical life support systems are essential for safe entrapment in the event of an emergency and to examine considerations for their application.

Aug 1, 2013

By Wemerson Junio Gandra

Para a redução do minério de ferro no alto-forno é necessária a utilização de uma fonte de carbono, que pode ser encontrada no carvão mineral e/ou carvão vegetal. Diante do cenário atual, a busca constante por maior competitividade, associada ao atendimento da qualidade e aos requisitos ambientais, exige a implementação de várias ações alternativas no processo de fabricação de gusa. Dentre elas, destaca-se a utilização de combustíveis alternativos no sistema de injeção dos altos-fornos, como por exemplo, a substituição parcial do carvão mineral pelo carvão vegetal. Do ponto de vista ambiental, é altamente favorável a utilização de uma fonte renovável de carbono. O objetivo desse trabalho é apresentar a adequação do processo, desde o recebimento do material até sua injeção nos altos-fornos, bem como os resultados já alcançados e os desafios futuros. A utilização do carvão vegetal na mistura de carvão pulverizado resulta em flexibilidade na utilização de matérias primas e contribui para preservação do meio ambiente.

Oct 30, 2017

By Christopher J. Brown

"Proper ground stability in gate roads has been a critical aspect of success in longwall mining. In particular, the tailgate has proven to be one of the more active mine areas that needs to be managed (Barczak, Dolinar, and Mucho, 1999). As longwall tailgate support technologies continue to be developed and improved, Strata Worldwide has worked to design and manufacture a revised Propsetter to provide additional support capacity and enable applications at greater mine heights. The support is targeted for tailgate applications; however, it can also be used for roof support in various types of mining environments. This paper describes the design changes for enhancing the support capacity of the Propsetter to more closely align its performance with other support technologies currently being employed in longwall tailgates. Balancing changes to each design aspect of the Propsetter was key to successfully improving the roof support load capacity while maintaining controlled deformation. Increasing the load capacity would allow a mine to improve support efficiency with a smaller, less intrusive support compared to support alternatives and to reduce the cost per foot of supported entry. The target support capacity was 80 to 100 tons at two inches of deformation to more closely match the performance of competing tailgate supports, such as the 24-inch-diameter CAN®. To achieve this goal, changes were made to all design aspects of the Propsetter: diameter, wedge cut depth and angle, pod size, and confinement rings. Test results from the NIOSH Mine Roof Simulator verified that these design changes were successful in increasing the capacity of the Propsetter to the 80- to 100-ton range at two inches of deformation. INTRODUCTION Roof support is one of the most fundamental elements of the underground mining process. As materials are removed from the earth, geological conditions will almost always require some form of roof support to keep the extraction area open and stable. Coal mining environments often experience difficult geological conditions that require both primary and secondary forms of roof support to keep the mining environment safe and economical. The secondary support system serves as additional support in the case the primary support system is inadequate. If designed properly, the secondary support system will also assist in maintaining integrity of the immediate roof beam (Barczak, 2000)."

Jan 1, 2017

By Tiago Nunes Lima

As propriedades mecânicas de ligas TiNbSn são dependentes do processamento termomecânico. O refinamento dos grãos das ligas é obtido através de processos de conformação a frio, atingindo valores de redução que podem estar acima de 80%. Esta deformação a frio permite o aumento das propriedades mecânicas, mas pode reduzir consequentemente a ductilidade e a tenacidade das ligas. Este estudo tem como objetivo observar o efeito da laminação e forjamento a frio nas propriedades mecânicas de ligas Ti35Nb2Sn com 80% de redução. Foram realizados ensaios de tração, dureza, metalografia e microscopia das fraturas. Ambas as ligas deformadas e envelhecidas apresentam as fases ß, a” e ? em suas microestruturas, porém, com algumas mudanças microestruturais. Foi notado que a liga forjada possui maior resistência máxima a tração e dureza que a liga laminada.

Aug 16, 2017

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

La presente investigación revela aspectos sobre los métodos geoquímicos aplicados a la exploración de depósitos minerales, como las aplicaciones prácticas e indicaciones sobre de las diversas técnicas empleadas en el campo y y laboratorio. La exploración química de los depósitos minerales como método de prospección, comprende la investigación e interpretación de anomalías químicas relacionadas a la mineralización dentro de varias sustancias naturales como rocas, aguas y vegetación para así localizar depósitos minerales ocultos. La naturaleza de estas anomalías se divide en dos grupos: las anomalías primarias formadas durante el periodo de mineralización y las secundarias, formadas por la destrucción y dispersión del depósito metalífero durante el ciclo de intemperismo y erosión. Sin embargo, existen algunas anomalías de naturaleza "residual" o "vestigial", las cuales son descubiertas mediante el muestreo sistemático de rocas o de los suelos que de ellas derivan. A esto se suma, la dispersión de elementos en solución puede dar origen a muchas variedades de anomalías secundarias que tienen importancia en la exploración geoquímica como las dispersiones secundarias en las aguas de fuentes, pozos y aguas corrientes, en las cajas de cuerpos mineralizados; en coberturas de carácter no residual sobre y cerca de depósitos mineralizados y aquellas dispersiones secundarias en vegetales. Paralelamente a esta exploración geoquímica, tenemos otras métodos comom los técnicas colorimétricas, basadas en reactivos que indican cambios de color y los de análisis espectográfico, que complementan paulatinamente dicho proceso minerológico.

Jul 20, 1956

By N. S. Dalal, A. H. Hoffman, X. Shi, D. E. Banks, J. K. H. Ma, Y. Rojanasakul

Excessive production of reactive oxygen radicals by alveolar macrophages is proposed to play an important role in oxidative lung injury. A major product of oxygen radical formation is the highly reactive hydroxyl radical (•OH) generated via a biologic Fenton reaction. In addition to its known ability to induce lipid peroxidation, recent studies have suggested that the •OH may exert its cytotoxic effect through the alteration of [Ca2+], homeostasis. To test this potential mechanism as well as to investigate the relationship between •OH and Ca" overloading in cytotoxic injury, isolated rat alveolar macrophages were exposed to externally generated radical system, H2O2 (0.01 to 1 mM) and Fe (1 mM) and their [Ca2+] levels and cell injury were monitored using quantitative fluorescence microscopy with the aid of the specific Ca" indicator, Fura-2, and membrane integrity indicator, propidium iodide. Electron spin resonance measurements using the spin trap 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) confirmed the production of the .OH radical by this system. Upon the addition of the radicals, the macrophages displayed a rapid initial rise in [Ca2+] which was followed by a slower but more pronounced [Ca2+], elevation that reached a level 3 to 5 times higher than the basal level. This process preceded cell death as evident by nuclear propidium iodide fluorescence. Depletion of extracellular Ca" inhibited both the [Ca2+], response and cell injury. Preincubation of the cells with the Ca" channel blocker verapamil or .0H radical scavenger mannitol similarly inhibited the [Ca2+], rise and loss of viability. Firefly luciferase assay of cellular ATP content demonstrated that the alterations in [Ca2+], following .0H treatment preceded the depletion of ATP. Changes in membrane potential caused by Na* substitution with K* had no significant effect on either the unstimulated or stimulated [Ca"], levels. Taken together, these measurements indicate that .OH-induced injury in alveolar macrophages is associated with the alteration in [Ca2+], homeostasis. The mechanism of •OH-induced [Ca2+] loading is not due to nonspecific membrane damage or energy depletion, but mainly due to an increase in Ca2+ influx through Ca2+ selective channels. This Ca2+ over-load state as well as energy depletion caused by the oxidant may activate certain cellular degradative processes leading to cell injury and death.

Nov 1, 1995

By Bernard Lewis

The ignition problem: for a layer of firedamp bordering on a cloud of detonation products is evidently considerably more complicated than in the usual laboratory ignition experiments, in which a well-defined volume of gas is heated and the occurrence of ignition is observed after an induction period. An atmosphere of firedamp exposed to the detonation of a high explosive is subjected to heating by shock-wave compression and thermal conduction and to intermixing at the interface of the firedamp atmosphere and the cloud of deto¬nation products. Although a reliable physical-chemical analysis of the problem is not yet possible, one may nevertheless form a general view of the role of compression waves and the processes of heat transfer and diffusion at the interface. Near the mouth of a shot hole, or near a freely suspended cartridge, the firedamp atmosphere attains very high temperatures by adiabatic compression, and it is certain that such temperatures are sufficient to initiate chemical reaction. The pressure wave pattern is reproducible from one test charge to another if the initial experimental conditions are held constant; on the other hand, experiments on firedamp ignition do not yield a reproducible threshold condition for ignition, but only an ignition probability. Thus, the induction periods are sufficiently long that there is time for the compressed', heated gas layers to undergo random changes that may quench or promote ignition. Therefore, the analysis of the ignition problem hinges primarily on the discovery of the random events that modify the chemical reaction in the activated gas layers.

Jan 1, 1948

By C. Villa Diniz

It is proposed that battery grade Mn02 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

By Andrey de Moraes Barcelos Casanova, Rebeca Vieira de Oliveira, Juliana Diniz e Castro, Danilo Abílio Corrêa Gonçalves, Patricia Freitas Rodrigues, Thiago Henrique Fernandes Dias Ferrão, Naiara Vieira Le Sénéchal, Rodolfo da Silva Teixeira, Andersan dos Santos Paula

Este trabalho avaliou a efetividade do tratamento térmico de solubilização de uma liga de NiTi com 58,5%at. Ni comparado a uma liga de composição equiatômica, elaboradas por vacuum arc remelting (VAR). A solubilização foi realizada à 950 °C, em forno de atmosfera não controlada, com tempo de encharque de 2 h, seguido de resfriamento rápido em água à temperatura ambiente. Foram analisadas imagens de microscopia óptica e de microscopia eletrônica de varredura, após preparação metalográfica, das amostras fundidas e solubilizadas, bem como, quantificação da segunda fase pela análise de micrografias ópticas. As propriedades mecânicas foram avaliadas pelo ensaio de dureza por microindentação Vickers. O tratamento térmico imposto resultou em alterações morfológicas na liga equiatômica e não foi possível verificar a dissolução completa dos precipitados da liga com elevado teor de Ni. Foi observado a diminuição da dureza com a solubilização do NiTi equiatômico, e aumento na liga Ni58,5%at.-Ti41,5%at.. Logo, para se obter uma solubilização ótima das ligas, se faz necessário um tempo de encharque maior.

Oct 22, 2019

By Mitchell M. A

The steeply dipping Mammoth orebody is mined by Gunpowder Copper Limited using a sub- level uphole bench stoping method at a mining rate of 350 000 tonnes per year. of three per cent copper ore. Access to the mine, is provided by 1 in 9 decline which spirals in the footwall connect-, ing all the sublevels, thus maximising mobility and accessibility of trackless mining equipment Sublevels are driven in ore off cross- cuts from the decline every 15 metres vertic- ally. Sublevel drives are stripped out to widths up to 18 metres before cutoff slots are mined at each end. A two boom fan drilling jumbo is used to drill inclined rows of holes to the floor of the sublevel above. Two or three rows are fired at a time which allows broken ore and remnants from the level above to be mucked out by rubber tyred LHD equipment to the brow. Ore widths of up to 80 metres are en- countered at lower levels where ring drilling from longitudinal drill drives will break ore to a draw point system below. Development is carried out with three boom rubber tyred jumbos. All haulage from the mine is in 20 and 35 tonne rear dump trucks. All aspects of the mining operation are discussed including ventilation, pumping and drainage, services and future planning.

Jan 1, 1974

By C. C. Clark, R. R. Backer, J. D. Vickery

This report presents the results of tests conducted by the U.S. Bureau of Mines to determine the transport characteristics of highly concentrated paste backfill mixes made from dewatered total mine tailings. The slurry concentrations of the mixes were all above 78 pct by weight with slumps ranging from 6.4 to 16.5 cm (2.5 to 6.5in). Laboratory material property tests and full-scale pumping tests were conducted using pipe diameters of 102,128, and 154 mm (4, 5, and 6 in) and a positive-displacement pump. The results indicated that the tested backfill mixes can be successfully transported as a stiff paste and identified the influence of and the interaction among the various mix and system variables.

Jan 1, 1995

By Chamberlain A. C, Fisher N, Avraamides J

The thermal decomposition of sodium ethyl xanthate (SEX) adsorbed onto activated carbon was studied by coupled thermogravimetric analysis-Fourier transform infrared spectroscopy (TG-FTIR). Two discrete mass losses were observed, in the temperature ranges 100 - 230¦C and 200 - 340¦C. The same two gases, carbonyl sulphide (COS) and carbon disulphide (CS2), were the main gases evolved in each of the mass losses. Samples of activated carbon from two industrial plants were obtained and analysed by TG-FTIR. COS and CS2 were not detected in one of the samples. The other sample did show evidence of COS and CS2, which indicated that fouling of the carbon by SEX was still present. Other organic compounds were detected in the evolved gas stream of both samples, indicating the presence of organic reagents other than SEX.

Jan 1, 1996