Search Documents

By Rafael Pinto Pretti Assef

Apresentar o Balanço Energético Global da Usiminas em 2016 - Usina de Ipatinga, com os principais indicadores de consumo das áreas produtoras. Além dos indicadores energéticos globais, o balanço apresenta os consumos físicos específicos de cada insumo nas diversas áreas, permitindo a análise de cada setor da Usina, isoladamente.

Jan 26, 2018

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By Robert F. Stevens, Robin Givet, Kenneth Viking

"Summary This paper describes a case of a directional pile installation conducted from an existing oil platform in the Caspian Sea, offshore Baku. Results are presented for 660 mm outer diameter (660 mm OD) conductor piles. Each conductor was equipped with a beveled aluminum toe for directional impact driving and was driven through a 710 mm casing using a Delmag 100–13 diesel hammer and a chaser pile. The 710 mm casings were preinstalled to a depth of 75 m below mud line (75 m BML). The longest impact driven conductor pile on the project was 456 m at end of drive, and reached the terminal depth of 295 m BML.Soil conditions consisted of soft to stiff silty clay to a depth of 30 m BML, underlain by stiff clay to 96 m BML, very stiff silty clay to 200 m BML, and very stiff to hard clay down to 300 m BML.In order to assess the maximum stresses in the conductors and check the performance of the hammer, the driving of each conductor was monitored using a Pile Driving Analyzer (PDA). The hammer fuel setting was adjusted based on the PDA outputs to ensure the conductors were not overstressed during installation. All driving and monitoring operations were carried out from the drill floor.The conductor piles drove easier than anticipated but in the direction predefined by the pre-cut angle of the beveled aluminum toe. The driving system performance was good. Post driving, the SRD were analyzed by either the global method analysis, using WEAP, or by the CAPWAP program.To detect any collision between the conductor being driven and the adjacent wells in production, the well heads were monitored in real time with high sensitivity accelerometers. These accelerometers were connected to an alarm system on the drill floor, triggering a siren and a strobe light should a collision be detected by an abnormal increase of the peak acceleration.IntroductionThe world longest directional impact driven pile was installed in year 2005. The operation was carried out from an offshore production, drilling, and quarters (PDQ) platform located about 120 km east of Baku, in the Caspian Sea.The platform foundation consists of driven piles and 24 slots were available for drilling the wells to the reservoir, located about 3800 m below sea floor. Each slot was fitted with a casing, 710 mm in diameter, running from the top of the jacket to a depth of about 75 m BML (Figure 1). Oil production started in 1997 and by the end of 2003, 14 wells were in operation; 10 slots were therefore still available, either for oil production or for water injection. However, due to larger than expected settlement of the platform, drilling of additional wells was put on hold. After further investigation, experts concluded the settlement was due to an alteration in the mechanical properties of the bearing strata supporting the foundation piles. This alteration was due to either excess soil material transportation, or soil fracture by the drilling fluids (mud), when drilling the first wells. With only 14 wells in production, out of 24 possible, the owner faced a new dilemma: to drill, or not to drill new wells?"

Jan 1, 2014

By H. E. Grier, H. H. Aronson, H. F. Coffer

"Nuclear explosions are currently being planned for use in oil and gas production, the recovery of oil from oil shale, gas storage and copper leaching. The current status of each of these projects is discussed, with emphasis on the economics of each application. The first commercial application of nuclear explosives will be in gas stimulation. Project Gasbuggy will be rapidly followed by two additional shots, also related to gas production. These three events, each in a different formation, will be described in this paper with a discussion on their significance to the world's oil and gas industry. The use of nuclear explosives in oil and gas stimulation should be a standard accepted practice within a few years. Calculations based on explosions in media such as tuff, alluvium, granite and dolomite predict large increases in productivity when nuclear devices are used in tight, thick formations. The broken-up rock resulting from the explosion becomes the new well bore, with a production rate of six to twelve times that of a normally completed well.Also included in the paper is a discussion of the real or possible problems associated with nuclear explosive engineering. The only major foreseeable problem is the seismic shock wave. This limits the size of explosive which can be used near important surface structures. A discussion is included on the radiation problem, which we believe to be largely psychological in the case of contained explosions."

Jan 1, 1968

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969

By Ramon Santos Corrêa

Com a descoberta de poços de petróleo cada vez mais profundos, as tolerâncias das propriedades mecânicas dos tubos de aço utilizados para este fim estão mais restritas. Somando-se a isso, o mercado pressiona por redução de custos e agregação de valor nos produtos ofertados. Por outro lado, a maturidade de interconexão alcançada pelos sistemas industriais, permitiu a disponibilização de dados mais precisos dos processos e a utilização de ferramentas computacionais avançadas de análise e modelagem de dados. Este trabalho tem como objetivo prever as propriedades mecânicas dos tubos após o processo de revenimento, a partir da composição química do aço, parâmetros dimensionais dos tubos e parâmetros do processo. O acompanhamento on-line da tendência das propriedades mecânicas permitiu uma operação preventiva no forno de revenimento, possibilitando a redução do lead time do processo, visto o tempo médio de 2 dias para o recebimento dos resultados do laboratório. A definição pela utilização das Redes Neurais Artificiais se baseou em trabalhos relacionados ao tema e casos de sucesso aplicados na indústria. Observou-se que os resultados obtidos a partir dos modelos obtiveram índices de assertividade superiores aos de outras técnicas utilizadas para este fim. Além disso, foi possível a criação de um único modelo para cada propriedade mecânica considerando todas as famílias de aço produzidas na Vallourec, facilitando os processos de calibração e sustentabilidade dos modelos.

Aug 16, 2017

By Xinyang Wang

It is believed that sulfur and volatile matter con-tents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017

This paper describes the results of a laboratory study on the upgrading of Algoma siderite by the amine flotation of silica and silicate gangue. The experiments indicate that a virtually complete removal of silica is possible in a rougher flotation con-ducted in tap water at natural pH, without prior desliming of the ore. Grinding considerably finer than the apparent liberation size is essential for maximum silica rejection. A cationic collector, Aeromine 3037, gave best results when used in combination with a modifier. Of the several modifiers tested, a Dutch potato dextrin, Dextrin 4356, was found to be the most effective. Both iron recovery and the grade of the final iron product are enhanced by floating the pyrite contained in the ore prior to the amine flotation of the silica, and by scalping the magnetics from the silica concentrate. F OR over twenty years, the Algoma Ore Properties Division of The Algoma Steel

Jan 1, 1963

By Douglas H. Brown

Cadmium and other 'minor' metals in Canada tend to remain inconspicuous given the prominence of the country's massive production of other minerals. This same reality is reflected in the accuracy and deficiency of quantitative data concerning the sources of supply and demand for these metals. It is the intent of this paper to identify the nature of some of these difficulties and to reconstruct a more accurate description of Canada's production and consumption of cadmium, based on the results of recent surveys undertaken by the Mineral Policy Sector of Energy, Mines and Resources Canada and Noranda Sales Corporation Ltd.

Jan 1, 1978

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By Willy Ank de Morais

Historicamente a execução de fundações profundas com perfis metálicos eram prejudicadas pela falta de sincronia entre as atividades de cravação das vigas e suas emendas. O grande problema é a demora na execução das emendas, tipicamente pelo uso de soldagem com talas, que normalmente leva 1 hora para ser completada. Neste trabalho analisou-se o Caminho Critico (MCC) da operação para incrementar a produtividade na execução de fundações profundas pela adoção de dispositivos, equipamentos e processos de alta produtividade, encabeçados por soldadores qualificados e certificados. Com isso, criou-se o processo INO///FAST®, aqui apresentado, que permite obter uma emenda, atendendo plenamente aos preceitos da norma ABNT NBR 6122:1996 (“Projeto e execução de fundações”), em apenas 10 minutos. O processo desenvolvido foi analisado, verificado e comprovado em uso prático por pesquisadores, engenheiros e técnicos.

Oct 30, 2017

By Mônica Aline Magalhães Gurgel

Este trabalho avaliou a evolução estrutural e mecânica dos ciclos térmicos realizados em uma chapa laminada a frio de aço baixo carbono com micro adição de molibdênio e nióbio destinado para a indústria automobilística, associado a classe dos aços bifásicos. Para realização do estudo foi feita a caracterização microestrutural e mecânica, por intermédio de amostras retiradas após a laminadas a frio produzidas em escala industrial, com auxílio das técnicas de microscopia óptica, e avaliação da dureza via Nanoindentador Instrumentado. Os ciclos térmicos foram feitos com o intuito de observar os processos de recuperação, recristalização, e transformação de fases no aquecimento e após resfriamento, com encharque em distintas temperaturas do campo intercrítico, via análise de dilatometria em um equipamento de análise termomecânica (TMA) em amostras extraídas da chapa laminada a frio “Full- Hard”.

Aug 16, 2017

By Cari Deyell, Brigette Martini

The AntaKori Cu-Au-Ag Project in the Hualgayoc mining district, northern Peru is a complex system dominated by calcic Cu-Au-Ag skarn hosted in Cretaceous sedimentary units. The skarn system is partially overprinted by two younger epithermal systems: high sulphidation (HS) epithermal gold-copper-silver mineralization related to the adjacent Tantahuatay system, and intermediate sulphidation carbonate-base metal Au-Ag-Pb-Zn-Cu mineralization related to late stage rhyolite stocks and flow domes (Wilson, 2012).

May 1, 2008

By M. Machina

Anew approach to the use of projectiles for rock fragmentation uses recently-developed technology to optimize projectile shape and composition to achieve the desired type of breakage. Projectiles can also be made of various materials, as determined by the requirements of downstream processes. This paper describes laboratory tests with an 21-mm (8-guage) gun, and field tests with a 60-mm cannon.

Jan 1, 2003

President Zakotnik opened the final session of the Institute at 9:30 a.m. Kenneth R. Herrmann of the Resolutions Committee presented the following resolutions to the group for their approval: RESOLVED: That the members of the Rocky Mountain Coal Mining Institute, in convention assembled, hereby ratify and confirm all official actions of the officers, the executive committee and other committees of the Institute between July 4, 1962, and the present time.

Jan 1, 1963

By K. Esmaieli

This paper addresses issues associated with ore pass degradation caused by material impact. A series of numerical experiments, using the particle flow code, were undertaken to investigate the influence of various finger raise configuration. This has allowed the identification of favorable configurations. The results of this analysis, when coupled with field observations, can contribute to the design of ore pass systems that can prolong the useful operating life of ore pass systems.

May 1, 2009

By Rafael Rocha Maia

No presente trabalho, analisaram-se três amostras metálicas ferrosas provenientes da Real Fábrica de Ferro de Ipanema (RFFI) outras três do sitio arqueológico de Sardinha (SAS) em busca de uma assinatura química dos processos produtivos destes objetos com base num modelo de regressão linear dos resultados de análise química de inclusões não metálicas proposto por Dillmann et al. [1]. Foram usadas técnicas de caracterização microestrutural associadas com microanálise EDS (Energy dispersive X-ray spectroscopy) destas inclusões. Com os resultados de microanálise, foram construídos gráficos de relações entre os principais constituintes destas inclusões (%FeO versus %SiO2, %SiO2 versus %Al2O3, %Al2O3 versus %MgO e %CaO versus % K2O). Utilizou-se, então, a técnica de regressão linear (com reta passando e sem passar pela origem) para cada uma destas relações de modo a obter e avaliar o valor do coeficiente de determinação linear R2. Aplicou-se, ainda, o teste de t de Student para avaliar a hipótese de “reta passando forçosamente pela origem”, como proposto por Dillmann et al. [1]. Não foi possível obter a assinatura química dos processos produtivos, visto que a análise estatística dos dados mostrou uma incoerência no modelo utilizado por Dillmann et al. [1], que assumia que a regressão linear passava pela origem dos eixos.

Aug 8, 2018