Search Documents

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent suficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involvetd the purchase of several hundred tons of halls of a specific type which were then run in one or more ball mills for a period ranging from several months' to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1'2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent suficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involvetd the purchase of several hundred tons of halls of a specific type which were then run in one or more ball mills for a period ranging from several months' to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1'2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By D R. Anstey

The growing demand for iron ore from Western Australia has led to an increased focus on the development of magnetite and lower grade iron ore deposits. The need to process and beneficiate the ore from these projects can result in the generation of significant quantities of iron ore tailings over the life of a project. Over the coming decades, the management of iron ore tailings will become a significant aspect of the mining landscape in Western Australia.The tailings generated from iron ore projects differ signifi cantly from other mineral tailings currently produced in Western Australia. Iron ore tailings are generated on a scale not matched by any other mineral process and can often contain asbestiform or potentially acid forming components. New iron ore projects are coming under increased environmental scrutiny because of their large scale operations and the sensitive environments in which they occur. This combination of factors creates some unique challenges for the management of tailings generated by iron ore mining in Western Australia.This paper presents the fi ndings of two studies conducted in recent years to overcome the challenges posed by iron ore tailings. The paper discusses the role of laboratory testing in the development of management strategies for asbestiform minerals in tailings. It also presents a numerical modelling approach for evaluating the rates of rise in the storage of magnetite tailings. The paper concludes by outlining how the findings of these studies can be applied to reduce tailings management costs, lower risks and improve environmental outcomes for the management of tailings from iron ore mining.

Jul 11, 2011

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By E. D. Attanasi, M. W. Bultman

Most statistical measures of mineral exploration continued downward in 1986. Prospects in 1987, however, appear to have brightened for exploration as the overall economic health of the mineral industry improved. The Society of Economic Geologists (SEG) survey of US and Canadian firms documents the marked decline in US mineral exploration since the early 1980's. From 1981 through 1986, the total exploration expenditure by US firms declined by more than 73% (Fig. 1). Exploration expenditures by US firms declined by 66%%. US based professional exploration staffs were slashed by 70% (Fig. 2). Also, many firms have written off some reserves because of weak markets or have not delineated new reserves to replace production. The Canadian government reported that between 1981 and 1986 Canadian molybdenum re¬serves had declined by 30%, lead and zinc reserves by 20%, and nickel and copper reserves by 15%. The SEG survey also shows the immediate impact of the decline in the dollar on US exploration expenditures abroad. Between 1981 and 1986 the share of the exploration dollar spent by US firms outside of the country declined by nearly one-half and exploration acreage abroad declined by 69%. The downward trend of the last six years may finally be near the end as a leaner and more efficient minerals industry starts to gear up for a period of increased activity. An industry survey reported to Mine Development Bimonthly (Metals Economics Group) indicates that mining firms were expected to increase exploration expenditures in 1987 by at least 10% above 1986 levels. Worldwide expenditures for 1987 by companies covered by the report were expected to top $800 million. It is the first time since 1984 that an increase in exploration expenditures was expected. Also, the US Bureau of Land Management reported a 30% increase in new mining claims for fiscal year 1987 over fiscal year 1986. The bulk of the increase in claims was in states having intense gold exploration, particularly Washington and Oregon. Much of the optimism is undoubtedly due to the increases in metal prices that occurred in 1987. Some of these increases include gold, average price up about 20%; copper, average price up 24%; aluminum, average price up 26%; and nickel, average spot price up 20%. The SEG survey shows precious and base metals accounting for 89% of the exploration expenditures in the US in 1986, up 52% from 1981. The US Bureau of Mines estimates that 80% of US exploration activity in 1986 was directed entirely at gold (1986 Minerals Yearbook). Worldwide exploration plans indicate the continued dominance of gold exploration. New programs were announced for Ghana, Malaysia, and Indonesia. Major new exploration programs were also launched for lead-zinc sulfides in Morocco, platinum and palladium in northwest Brazil, rare earth minerals in Greenland, diamonds in Indonesia, and heavy minerals off-shore Australia. Significant gold discoveries were made at Angels Camp in Oregon; South Africa, near Potchestroom; India, in the Chitradgra district; Northern Ireland near Mt. Speerin; Chile, San Cris-

Jan 5, 1988

By Jingcheng Li

Currently many underground coal mines worldwide have installed or been planning to install a tracking system to trace miners mainly for their safety. Although many systems have been reported functional, a lack of sophisticated and systematic error correction methods apparently is still an issue for them; often it results in a low system resolution. To improve the system resolutions, this paper introduces two position adjustment methods for mine tracking systems. The first is an entry-matching method that optimally adjusts an off-course tracking device to the closest tunnel (entry). The second is a distance measurement adjustment method that accurately adjusts the position of a tracking device along an entry according to a measured distance from the device to a reference point. The coplanar node-path network mine model is used as the foundation for the development of these two methods.

Jan 1, 2009

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By James S. Browning

Heavy liquids have been used to separate minerals of different specific gravities for many years.4 5 6 7 8 9/ The method permits substantially quantitative evaluation of a variety of minerals and requires much less time than the usual methods of chemical analysis. This Bureau of Mines investigation was conducted to determine the applicability of heavy liquid mineral separation to the evaluation of certain spodumene and kyanite ores, prepared mixtures, and plant products. After careful standardization of the particular mineral and associated gangue, estimates of chemical analyses could be obtained from results of heavy liquid separations.

Jan 1, 1960

This paper describes experimental investigations into the reductive decomposition of arsenopyrite/pyrite (FeAsS/FeS2), a gold and silver bearing iron/arsenic sulphide using metallic iron powder. The main objective was to establish and experimentally confirm the thermodynamic and kinetic feasibility of reductively decomposing the sulphide matrix for precious metals recovery. In this context, cyanidation leach tests were conducted on the reductive leach residues. The arsenopyrite/pyrite flotation concentrate, mainly studied in the hydrochloric acid medium, decomposed through the non?oxidative chemical dissolution reaction and the reductive decomposition reaction for the arsenopyrite and pyrite components, respectively. Desulphurization levels below 65% were achieved at pH values below 0.15 and iron to concentrate ratios above 1, and the system was characterized by overall very slow kinetics. The reaction system had a direct linear relationship with iron to concentrate ratio and an inverse relationship with pH. An analysis of the pyrite/iron galvanic system showed that pyrite forms a partially inert cathodic surface on which the anodic dissolution of iron occurs, supported by the hydrogen evolution reaction. This phenomenon explained the low desulphurization levels and the mineral decomposition seemed to be restricted to the non?oxidative chemical dissolution reaction for the arsenopyrite component. The cyanide leach of the reductive leach residues showed very little improvement in gold recovery. The reductive leach process for arsenopyrite/pyrite has considerable limitations in terms of both desulphurization and precious metals liberation. Keywords: Pyrite, arsenopyrite reductive leaching, hydrogen sulphide, invisible gold

Jan 1, 2009

By Noel N. Moebs

Five LANDSAT lineaments in the coal mining region of southwestern Pennsylvania were investigated by the Bureau of Mines to determine their geologic character, relation to subsurface conditions, and the means of discriminating one from another. The investigation included earth resistivity and very low frequency (VLF) electromagnetic traverses, soil moisture sampling, and a correlation with coal mine roof conditions. The lineaments could not be detected by the methods used, suggesting that they might be a surface phenomenon unrelated to subsurface geologic structures or roof stability in coal mine workings beneath.

Jan 1, 1987

By F. E. Joyce, Charles Prasky

This report describes the response to high- temperature sulfatization of a variety of manganese minerals and companion compounds which may occur either as a principal component or as a gangue material in low- grade manganese deposits . Fourteen manganese samples representing oxide , carbonate , and silicate minerals as well as seven compounds which might occur as gangue with manganese minerals were tested batchwise in a bench- scale apparatus under conditions which would be favorable for the sulfatization of manganese . The manganese minerals substantiated thermodynamic predictions and responded to sulfatization but to varying degrees . The gangue materials , MgO , MgCO,, CaO , and CaCO3 , were sulfatized readily in contrast to the iron oxides and the aluminacontaining material which were not .

Jan 1, 1964

By Luiz Gustavo Franco Amaral

The recent tragedies that occurred in Brazilian territory had a greater impact than that presented in the major newspapers and led an entire industry to question the technology and techniques that were previously practiced in the mining industry. With this, there is the prospect of new projects and innovations in the most varied branches of engineering. This publication presents computational technologies to support the decision making of engineering projects aimed at the mining sector and explores the benefits obtained from the use of current technologies in the mining sector. Recent works are referenced in order to propagate not only the methodology employed in these researches, but also to provide the reader with an overview of the industry and companies that invest in technology to support their decision making in the most diverse projects gains on products and processes obtained through this practice.

Oct 3, 2019

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By H. J. Levinstein, H. J. Guggenheim

RbFeF3 is a transparent ferromagnet with a large faraday rotation which permits the direct observation of magnetic domain structures in bulk crystals. If the position of dislocations within the crystal were known a study of domain wall dislocation interactions would be possible. In this paper an etch pitting solution is described which gives a one-one correspondent between the etch pits and the dislocations intersecting the (100) surfaces of RbFeF3 crystals. In addition, RbFeF3 is shown to have sufficient plasticity so that known arrays of dislocaticms can be put into the crystal. It is concluded that RbFeF, is an ideal material for the investigation of domain wall dislocation interactions. THE influence of lattice defects on the motion of domain walls in ferromagnetic materials has been studied extensively both theoretically and experimentally.4 The experimental data obtained has been qualitative in nature due to the lack either of a quantitative knowledge of the magnetic domain array in the material or of the nature of the dislocation configuration in the material. At room temperature RbFeFJ has the cubic perovskite structure. It is ferromagnetic below 86°K.5,6 It is also transparent and has a large faraday rotation in the magnetic state.7 The domain structure of this material is observable in three dimensions in crystals which are millimeters in thickness.' Since RbFeF3 satisfies the requirements of having an easily visible three-dimensional magnetic domain structure, it was of interest to determine if the dislocation structure of the material could be determined and if the material was sufficiently plastic so that dislocations could be introduced into the as grown crystals. This is a report of the results of that investigation. EXPERIMENTAL PROCEDURE The crystals of RbFeFs used in this experiment were grown by a technique described elsewhere.5 In order to obtain flat strain-free surfaces, the samples were first cut to the crystal orientation desired and the surfaces were polished by employing standard metallographic techniques. The samples were then immersed in a solution of 1 to 3 g of KOH in 100 ml of water. This solution removes the damaged surface layers uniformly leaving a film on the surface of the sample. Etch pits are obtained by immersing the sample in an approximately 50-50 solution of 30 pct peroxide and concentrated acetic acid. The film formed during the KOH treatment turns deep red in color in the etching solution and flakes off the sample. The etching time required depends upon the pit size desired and

Jan 1, 1970

By D Macfarlane, T McMorran

  This paper describes the design and construction of the upper section of the Pike River Mine Access Road. The road extends 11 km from Logburn Road alongside Big River on the West Coast of the South Island of New Zealand up Pike Stream to the new mine portal on White Knight Stream (Figure 1). This new road starts on alluvial terraces, then partially follows an old logging road before entering virgin bush and traversing the true left bank of a steep sided gorge on Pike Stream some 50 - 100 m above the stream before dropping down to the mine entrance. Its development has been an extended process from route selection, consenting through to design and construction.   The paper focuses on the 1 km section of road between the Amenities Area (Figure 1) and the portal. This section of road is a steep section through the gorge, principally on Conservation estate, and has presented the most challenges and required the greatest effort to obtain the regulatory approvals, prepare the design and to construct. This paper outlines the history of the challenges faced and how the road was successfully developed.

Jan 1, 2007

By B. Barry, M. S. Klima

"Testing was conducted to evaluate the effects of hydroacoustic cavitation (HAC) treatment on two bituminous coal slurries and the subsequent separation of each slurry in a classifying hydrocyclone. HAC treatment was performed using a pilot-scale circuit fabricated by Furness-Newburge Inc. The circuit was designed to induce cavitation by means of flow through an ultrasonic resonator chamber or enhanced cavitation by initial flow through a cavitation chamber followed by flow through the ultrasonic chamber. The test materials were nominal -1,500-micron and -150-micron Illinois-basin bituminous coal slurries, which were obtained from an operating coal preparation facility. After 5 sec of HAC treatment, the median size of the -1,500-micron material was reduced, with ash values for certain size fractions decreasing more than 5 percent compared with untreated samples. Extending treatment time led to greater degradation of the +1,180-micron material and an increase in the -25-micron material, with ash reductions occurring for material in the -850+150-micron size range. Size degradation was less for the -150-micron material. Subsequent separation of the treated slurries was carried out in a hydrocyclone with diameter of 102 mm. HAC treatment led to a decrease in the ash value and an increase in the heating value of the underflow stream compared with the feed material. For example, the ash value was reduced by about 16 percent for the -1,500-micron material and 25 percent for the -150-micron material with heating value increases of 7 and 33 percent, respectively, after HAC treatment. Overall, HAC treatment appeared to have a slight effect on the size selectivity curves.IntroductionUltrasound in the range of 20 to 1,000 kHz, referred to as power ultrasound, consists of high energy waves that can create zones of compression and expansion when used to irradiate liquids (Frederick, 1965; Leighton, 1994; Mason and Lorimer, 1988). This action generates varying pressure regions leading to cavitation or the formation, growth and near-immediate collapse of microscopic voids or bubbles (Frederick 1965; Leighton 1994; Mason and Lorimer 1988). Collapse occurs when the bubble reaches critical size and cannot absorb additional sound field energy, and the critical size is governed by the ultrasound frequency (Shchukin et al., 2011)."

Jan 1, 2015

By Ann G. Kim

Acid drainage from underground coal mines and coal refuse piles is one of the most persistent industrial pollution problems in the United States: This Bureau of Mines report reviews the acid mine drainage problem generally and describes research currently underway to combat it.

Jan 1, 1982

By Fernanda de Melo Fernandes

A deposição de filmes finos por plasma melhora várias propriedades físicas, químicas e biológicas de superfícies que contribuem para o enobrecimento dos materiais. O objetivo desse trabalho é estudar a cinética de deposição de filmes finos de cobre, utilizando a técnica da gaiola catódica, alterando a espessura da tampa da gaiola, e sua relação com a variação da potência do tratamento. Filmes de cobre caracteriza-se como bom condutor elétrico e térmico, o que justifica seu uso em microeletrônica, segundo a U.S. Environmental Agency (EPA) existem 282 tipos de ligas de cobre bactericidas, habilitando sua utilização em ambientes estéril. Assim, realizou-se deposições de filmes finos de cobre sobre substrato de vidro, variando a corrente do processo e a espessura da tampa da gaiola. Avaliou-se a variação de peso da amostra depositada, definindo o peso resultante das deposições. Realizou-se também a caracterização por difração de raio-X, microscopia eletrônica de varredura e análise tribológica (calotest). Os resultados mostraram que, o tratamento com espessura de tampa de 12 mm promoveu o filme mais espesso e mais contínuo dentre todos os tratamentos, com uma grande quantidade de cobre depositado, o que induz que a razão ideal diâmetro de furo/espessura da tampa é 0,67.

Oct 30, 2017