Search Documents

By Julie Hunt

Rimfire Minerals Corporation: early stage precious metal exploration specialists with discovery opportunities in partnership with major and mid-tier gold producers or prominent junior exploration firms. Mike Roberts, Senior Geologist

May 1, 2006

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By Li Shibo, C. Halls

The compositions of olivine, pyroxene and chromite from the Proterozoic ultramafic complex are analagous to those of cumulate ultramafic rocks of tholeiitic origin, suggesting that the parent magma may have been tholeiitic rather than komatiitic. The complex contains economically significant Ni-Cu sulphide mineralisation. The high sulphide/silicate ratio is best explained in terms of the segregation of sulphides from a large volume of magma, of which all but the ultramafic cumulate fraction has since been eroded. Platinum-group minerals that have been identified include sperrylite, moncheite, native platinum, froodite, merenskyite, michenerite and Pd-rich pentlandite lamellae exsolved from pyrrhotite. They are characteristically found in close association with chalcopyrite, either along the contacts between hydrosilicate and sulphide grains or in cracks within pentlandite and chalcopyrite, which may also be intergrown with galena. Crystallisation from a Cu-rich residual magmatic liquid also enriched in Pt, Pd, As, Sb, Bi, Te, Zn and Pb is postulated.

Jan 12, 1993

By M Oyarzún

Direct relationships between rock texture and BWi (grindability index) have been established based on geological and metallurgical information supported by optical microscopy observations, gathered from 731 samples.Each recognised rock texture is observed to be related to a certain BWi range and, this texture is also characteristic of distinct lithological subunits (recognisable at mapping scale). Therefore, this relationship may provide an important tool for early milling in situ estimation.Since each textural type is a response to rock formation conditions, the causality of the relationship between BWi and texture is based on such conditions and, particularly, on the interfacial free energy among its components.According to the abovementioned textural features, the greater the free interfacial energy between mineral components, the greater the necessary energy required to break its grain boundaries and, consequently, the greater the necessary energy required for milling.If the textural evidence indicates that the rock was able to adjust the shape and/or size of its components – in a natural tendency of all systems to minimise energy– then the necessary energy required to break its grain boundaries will be lower.

Sep 5, 2011

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982

By Lucas Ladeira Lau

A legislação ambiental vem se tornando mais restritiva em diversos setores industriais. Isto não tem sido diferente para o setor siderúrgico. Com a inclusão de limites de emissão de elementos traços nas legislações ambientais mundo afora, este tema vem ganhando importância. É conhecido que a qualidade das matérias-primas utilizadas nos processos siderúrgicos pode interferir nos impactos ambientais de seus processos. No caso do processo de sinterização, a presença de elementos traços está ligada a composição de sua carga. Com o objetivo de determinar quais elementos irão compor as emissões atmosféricas, resíduos, efluentes e produtos faz necessário estudar o modo de ocorrência dos elementos traços em cada insumo. A interação entre as propriedades de cada elemento e as condições de massa e termodinâmicas permitem o estudo de seu comportamento e partição. Assim, o objetivo deste trabalho é levantar o estado da arte da sinterização de minério de ferro e suas emissões, estudando a origem, o comportamento e a partição de elementos traços e radionuclídeos, quando submetidos às condições do referido processo.

Aug 1, 2018

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By Carlton E. Brown

This report contains information on the cells or containers used to hold a known small depth (usually 1 mm. or less) of the dust-containing liquid from impinger, 5/6/ filter-paper,7/ and other samples collected from the air while the particles revealed by a microscope (equipped with a 16-mm., 0.25- or 0.50-N. A. objective and ordinarily used with axial light-field illumination) are counted in order to obtain an index of the concentration of dust in the sampled air. Information is given on such subjects as the kinds of cells available, kinds used, actual depths of cells, and construction of simple, inexpensive cells. ACKNOWLEDGMENTS The interest, encouragement, and assistance received from H. H. Schrenk, chief chemist of the Health Division, in the preparation of this report are gratefully acknowledged, as 'is all other assistance received.

Jan 1, 1945

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By Oliver Bowles

"Properties and Uses.Iceland spar is a name given to a pure crystallized form of calcite (CaCo3) which is sufficiently transparent and free of defects to be used in the manufacture of optical instruments. While the actual requirements are small, the degree of purity and physical perfection demanded renders it somewhat difficult to obtain suitable material.The properties of value in Iceland spar are its transparency combined with double refraction. It is used in the manufacture of polarizing microscopes, saccharimeters, colorimeters and photometers. Its most important use is in the manufacture of Nicol prisms, which constitute an essential part of every polarizing microscope. The principle governing the construction of the Nicol prism is as follows:Ordinary light in passing through a crystal of calcite is resolved into two rays of plane polarized light vibrating in planes at right angles to each other and having different indices of refraction. Thus the two rays follow different paths through the crystal. The prism of Iceland spar is cut diagonally and cemented together again with a transparent cement having an index of refraction intermediate between the two rays passing through the prism. Canada balsam is employed for this purpose. The prism is cut at such an angle that the ray having the greatest index of refraction meets the surface of the balsam at an angle greater than the angle of total reflection, and it is thus deflected to the side of the prism, while the second ray passes through. Thus one of the rays is eliminated and polarized light vibrating in a single plane is obtained."

Apr 1, 1920

By D. Robert Weir, Verner B. Sefton

The reduction roast-ammonium carbonate leach-hydrogen reduction process for laterites has been under development by Sherritt Gordon for the past 20 years. The process can treat high iron or low iron laterites, with some process modification, and gives extractions of 88-93% Ni or 82-88% Ni, respectively. Five campaigns on a 1 tonne per day Pilot Plant and four campaigns on a 35 t/d Demonstration Plant have been carried out on laterite from three different deposits, and many other laterites have been investigated in the laboratory. The Marinduque Surigao Nickel Refinery in the Philippines was designed on the basis of this work. The process comprises roasting to selectively reduce the nickel and cobalt in the laterite, leaching the calcine in ammonium carbonate to dissolve the metals, recovery of cobalt by precipitation of a mixed metal sulphide, concentration of nickel from the carbonate solution by basic nickel carbonate precipitation and recovery of high purity nickel by hydrogen reduction of nickel from ammonium sulphate solution. Ion exchange has been developed as an alternative to BNC and for recovery of trace nickel from BNC barren liquor. Details of the development of some of the process steps through the laboratory to commercial plant are discussed. The process metallurgy has been confirmed in the commercial plant.

Jan 1, 1979

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By L. Ferland, D. LaRonde, J. C. Caron

"The free-world production of columbium ore concentrates has doubled in the last five years. St. Lawrence Columbium and Metals. Corporation has contributed largely to this expansion, its production rate increasing from 720 tons of concentrates per year in 1961 to 2 200 tons in 1965.To follow the normal market development, the Company initiated an engineering study aimed at establishing the most economical mining methods, thus permitting it to increase its milling rate from 1,000 tpd in 1964 to 2,000 tpd in 1967 and possibly to 3,000 tpd in 1968. The results of this study pointed out the advantages to be gained in converting from an open pit to an under-ground operation. This paper describes how the mining engineering department has successfully developed ""stopes"" from the walls of its No. 2 open pit, in order to assure continuity of its operation during the interval required to develop its underground mine."

Jan 1, 1967

By T. C. Huber

The southern African region has a high concentration of mineral resources and supplies much of the world?s platinum demand. As a result, the international community watches South Africa to understand the impact of supply on global markets. An analysis of supply certainty and risk plays a key role in the future of growing demand in various sectors. The southern African platinum industry experienced substantial growth in the early part of the 21st century, resulting in bullish forecasts for growth during the period of 2000?2006. However, southern African platinum producers saw a significant drop in production over the following three years as a result of many dynamic factors in operations and the global economy. Between 2006 and 2009 there was a million-ounce shortfall between forecast and actual production. This was raised as a concern at the Fourth International Platinum Conference in 2010 by Stephen Forrest during his keynote address, specifically regarding the lack of understanding in the market of the causes of this shortfall and any action that was being taken to address them. This paper reviews publicly available information in the media and corporate reports and communications for the period January 2006 to December 2009. In addition, several interviews were held with key stakeholders in the industry to provide further perspective. The paper then highlights the main reasons that are reported to have affected the loss in production over the period and discusses the possible implications of the information that the mining industry does and does not disclose regarding platinum supply.

Jan 1, 2012

By A. V. Lyamin, J. P. Wang, A. J. Li, Z. Qian

"For general stability analysis of rock slopes, rock mass strength and rock mass disturbance are definitely should be considered. In addition, the impact of earthquakes must be taken into account. In fact, the rock mass strength is very difficult to be assessed which causes the difficulty of analysing rock slope stability. Therefore, an empirical failure criterion, the Hoek-Brown failure criterion, has been proposed. It is one of the most widely accepted approaches to estimate rock mass strength. The rock mass disturbance is important and was found having significant influence on evaluating rock slope stability, especially for rock slope with poor quality rock mass. In the Hoek-Brown failure criterion, the disturbance factor can represent the level of the rock mass disturbance which would provide a reasonable basis for estimating rock mass strength.This research will not only discuss the slope factor of safety, but also consider the influence of the seismic force on rock slope stability assessment using pseudo-static method. In practice, only horizontal seismic coefficient is used. Various magnitudes of the disturbance factor and recommended blasting damage zone thickness are also taken into account. The blasting damage zone thickness considered ranges from 0.5 to 2.5 times of slope height. The research results have potential to be extended and then sets of comprehensive stability charts can be provided for the rock slope stability evaluations. They will be convenient tools for practising engineers. In this study, finite element upper bound and lower bound limit analysis methods are employed. Their applicability has been investigated in some previous studies. The differences between upper bound and lower bound solutions are less than ±10% which would provide reasonable and acceptable range for rock slope stability safety factor estimation."

Jan 1, 2015

By John E. Udd

"For decades, writers have expressed concern about impending shortages of professionals for Canada's minerals industry. Even under the present difficult economic circumstances, it is anticipated that the supply which will be available will not be adequate to meet the requirements in certain key areas including mining and petroleum engineering. It is evident that, unless further initiatives are taken, shortages will exist for some time.In this paper, the writer reviews information which relates to both the demand for, and the supply of, persons with advanced-level education in minerals-related disciplines. In particular, a summary is made of the information regarding supply which has been collected by the CIM General Committee on Education for many years.In concluding, the writer expresses some personal opinions regarding imbalances between demand and supply and offers some recommendations for future actions.IntroductionLast year, in a paper which was presented at the Annual General Meeting of the CIM in Calgary, the writer presented a review of the situation regarding professionally educated manpower for the minerals industry, and concluded that indications were that the gap between demand and supply was widening and that the situation could be expected to continue. Since that time, the deterioration of the nation's economy has caused an appreciable reduction in demand. Simultaneously, a further annual survey by the CIM has shown that the numbers graduating in certain specializations, notably geology and some of the technologies, are rising very rapidly. One of the great concerns of educators at present is that adequate opportunities may not exist for all of those who are now graduating.The danger of the present situation, then, is that a momentary lack of opportunities may cause potential students to choose alternative careers . Because of the lead-time which is involved, it is very possible that this could result in greater shortages during a period of economic recovery or expansion. Action must be taken to ensure that adequate numbers will be attracted to the industry, and this applies particularly to those who have already made the career decision and who are enrolled in minerals-related programs."

Jan 1, 1982

By G. Barr

"The Polymetallic Twin Metals Project deposits in Northern Minnesota are being developed by Twin Metals Minnesota. Amongst the flowsheet alternatives being examined at a prefeasibility study level is one involving flotation of a bulk concentrate followed by high temperature autoclaving of the concentrate using the PlatsolTM Process to solubilize all the valuable metals in the concentrate (Cu, Ni, Pt, Pd and Au). Autoclave operating conditions have been established in which recoveries of all the pay metals are in the 92 to 99% range, and the autoclave residence time has been reduced to an hour. The stability of the precious metals in solution after autoclaving has been assessed, as well as the impact of internally recycling process liquors to the feed to the autoclave.INTRODUCTIONPlatinum group metals (PGMs; platinum, palladium, rhodium, ruthenium, iridium and osmium) are traditionally recovered from their ores by production of a high-grade concentrate by flotation and/or gravity concentration followed by smelting of the concentrate. Concentrates are smelted to remove nonsulphide minerals and converted to remove iron and sulphur. The resulting high PGM grade matte is processed hydrometallurgically to leach the base metals, leaving a residue with a very high grade (20-40%) PGM concentrate for final refining to individual PGMs. Due to the complexity of this process and its high capital cost, this process can only be applied economically to high grade PGM ores. Lower grade PGM concentrates might be accepted as copper and nickel concentrates but may not yield attractive payment terms for the PGMs. The mineralized Duluth Gabbro region of Minnesota hosts several low grade base and PGM deposits and Twin Metals Minnesota is working to develop the Twin Metals Project deposits. Earlier studies at both pre-feasibility and feasibility level, by other mining companies, have failed to yield an economically viable project based on the traditional process. It is possible to produce a saleable copper concentrate from these ores, but economic recovery of nickel and PGMs into saleable concentrates proved elusive.In the late 1990’s and early 2000’s the Platsol™ process was developed at SGS in Lakefield, Ontario (at the time Lakefield Research Limited) for the NorthMet deposit (also within the Duluth Gabbro) owned by PolyMet Mining. The process developed was a high temperature chloride-assisted pressure oxidation process capable of dissolving simultaneously the base metals (Cu, Ni, Co, Zn), gold and the PGMs."

Jan 1, 2012

By K. A. ACKLEY

The petroleum industry experienced a year of satisfactory accomplishment in Oklahoma during 1945. Crude oil production was increased, a new record for recent years was established in well completions, and refinery operations were maintained at a maximum level. Daily average crude oil production increased to 382,000 bbl., reflecting a 13.5 per cent gain compared with production during the previous pear. Total wells drilled during 1945 amounted to 2556, a gain of 28.7 per cent over 1944 Refinery throughout averaged 187,500 bbl. daily, an increase of approximately 4 percent over the preceding year.

Jan 1, 1946

By Paul Biggs

This report presents information on 77 waterflood projects in 31 Montana oilfields. The study shows the locations of the projects, the sources and amounts of injection water, and the results in oil produced. Waterflooding, a secondary recovery technique, began in Montana about 40 years after the initial oil discovery in 1920. Often, the difference between water disposal by injection and pressure maintenance operations is not clear. Water injected at the projects in 1973 was 157.7 million barrels. In 1973, the 31 fields having waterflood projects produced 28.3 million barrels of oil valued at $88.4 million. Both in volume and value, this represents over 80 percent of the State's 1973 oil output. The projects are making possible the recovery of additional oil, thus contributing to the conservation of oil and lessening the impact of the current oil shortage.

Jan 1, 1976

By Filipe Sathler

O projeto CR298 se iniciou no final do segundo semestre de 2014 quando o Coque Rate (CR) médio era de 351,0 kg/t. A meta definida foi de atingir média mensal de CR de 298 kg/t em dezembro de 2016, permitindo aumento de produção com alta taxa de injeção de carvão PCI, porém, com baixo Fuel Rate, garantindo competitividade de mercado. Sendo assim, foi desenvolvido e divulgado um novo modelo mental de operação, processo, manutenção e gestão, envolvendo toda a área de Redução, Utilidades e Aciaria. Várias premissas técnicas foram estabelecidas com um plano de ação detalhado para garantir estabilidade no processo dos altos fornos de forma a obter este resultado. A meta foi atingida antes mesmo do planejado: CR 291,3 kg/t em Maio de 2016 e em 2016 a média anual foi de 297,0 kg/t, com Fuel Rate de 484,4 kg/t.

Oct 30, 2017