Search Documents

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By Steve Brace

Electronic detonators have been commercially available to the mining industry worldwide for over ten years. It is estimated that total cumulative global sales will have reached 25 million units by the time of the Conference in February 2004. This is below 0.2% of all detonator types sold during this period. Perhaps 20 million will have been used underground in South African gold, diamond and platinum mines. These will have been produced by South African companies, in South Africa for South African customers. Here efforts have met with greater success and in 2003 fully 5 million, or 3% of local detonators sold, could be of an electronic type. However, it is estimated that about US$7.00 (R50.00) has been expended on R & D, manufacturing facilities and marketing, for each unit so far sold. Large sums of money continue to be spent. Despite the apparent success in South Africa, is it justified? Electronic initiation systems have not produced significant technical benefits to the end-user underground nor corporate profits to the supplier. Some doubt they ever will (even from the large surface operations where the price per unit is much higher). A conclusion might be that they have failed. In 1998 Smit and Pistorius wrote a paper titled “Implications of the Dominant Design in Electronic Initiation Systems in the South African Mining Industry”. This ISEE paper seeks to summarise and review the conclusions of the earlier work. These were: that a dominant design had not yet emerged; the type of connector and the way in which detonators are connected and programmed would be a strong determinant influencing the development of a “winning” product; technical aspects rarely solely determine which becomes the dominant design (marketing, social and economic factors often have a strong influence); electronic initiation systems were an emerging technology for the underground gold mining industry in South Africa and because it was under severe cost pressure the mines would look to them to raise productivity and hence profits; finally, as a dominant design begins to emerge, one could expect a number of players to exit from the industry.

Jan 1, 2004

By Ann Barron, Mark Abernethy

Regardless of the care exercised by a blaster, seismic and acoustic effects produced by blasting can be disruptive and alarming to many people. With the general trend toward larger blasts, increased population, and urban sprawl, as well as sensational accounts of explosives - related incidents by the news media, fear and concern often leave residents searching for damage to their property. As a result, many blasting companies today find themselves at the center of litigation at an accelerating rate. Obviously, the best strategy for handling vibration and airblast complaints is to operate in a manner that does not create grounds for them in the first place. During the bidding process, ask questions. See the actual site to perf o rm an “exposure analysis.” Collect as many facts as possible before blasting including geological issues, contractual obligations, zoning, historical use of site, disruption of daily life to local residents, demographics of the surrounding area, as well as any unfavorable public opinions or prejudices connected with local construction projects or mining operations. A consultation with local pre-blast firms may assist in tracking down previous problems in the area.

Jan 1, 2004

By T Clemens, D Trumm

Adopting environmentally acceptable practices in New Zealand is a crucial requirement for mineral wealth development. Recent planned expansions in the coal industry have increasingly placed mining in the media spotlight. A lack of appropriate national environmental guidelines has resulted in inconsistent responses and assessments of current and prospective mine sites. Such inconsistencies have lead to delays in decisions on developing economic mineral deposits that may have only minor short-term impacts, and have also allowed unacceptable environmental management practices to continue elsewhere.   A research collaboration between CRL Energy, Landcare Research, University of Canterbury and University of Otago aims to provide regulator groups and the mining industry with a unified approach to the requirements of the Resource Management Act 1991, which is the legislation that predominantly drives the nationÆs environmental policies and guidelines. The tangible outcome of this research programme will be guidelines for an integrated decision-making framework based upon robust multidisciplinary science. The result of this unified process will facilitate the development of viable mineral deposits and prevent excessive environmental impacts.   The framework will be derived from a synthesis of four objectives. Objective 1 identifies potential water quality impact. This objective is based on a targeted geochemical study of the lithology and waterways of the West Coast and Southland. Objective 2 categorises the degree of impacts on the ecology of receiving aquatic ecosystems and determines the processes that drive aquatic ecosystem recovery. Objective 3 identifies best strategies to sufficiently manage impacted ecosystems, and to prevent future unacceptable impacts. Objective 4 combines the findings of Objectives 1 - 3 into a standard decision-making framework. The development of this framework development will include wide consultation with representatives of the mining industry and regulator groups. It is anticipated that this multidisciplinary approach will provide a robust and coherent, standardised system that will assist in achieving industry and environmental targets.

Jan 1, 2004

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By ManhKha Trinh, Neal Pyke

Dofasco was the first company to adopt oxygen steelmaking in North America in 1954, two years after the first LD vessel installed and operated successfully in Linz, Austria. Since then, Dofasco has investigated and implemented several strategies to maximize hot metal usage and minimize overall cost. Some key strategies -low hot metal silicon, combined blowing conversion, vacuum degassing tank upgrade and BOF slag carryover control - are discussed. Post combustion, scrap preheat, carbon injection trials along with current operating philosophies are described.

Jan 1, 2004

By A. Vahed

The Goro Nickel Project is situated in the Southern Province of New Caledonia. Inco Limited and Goro Nickel S.A. have developed a process that features the use of pyrohydrolysis to produce nickel oxide. The process treats a blend of laterites by Pressure Acid Leaching followed by solvent extraction of nickel and cobalt using Cyanex 301®. Purified nickel chloride solution is converted to high purity NiO product and 6M hydrochloric acid, which is recycled back to the SX circuit. In co-operation with Andritz AG, spray roaster and fluid-bed pyrohydrolysis technologies were examined for this purpose. Tests were conducted at the Andritz AG pilot plant in Vienna, Austria, and at Goro in larger scale installations. The latter served to establish process engineering design parameters for scale-up. Several process variables were investigated in both technologies and the off-gas characteristics were established. Fluid-bed pyrohydrolysis was selected for the Goro commercial plant, primarily because it produced a granular nickel oxide. The main focus of this paper is to outline the results obtained in pilot plant studies of liquid fueled fluid bed pyrohydrolysis for the Goro Project. Keywords: lnco Goro Nickel, Fluid Bed Pyrohydrolysis, Pilot Plant Tests

Jan 1, 2004

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By T. Yalcin, S. Brunet

The flocculant-assisted hydrocyclone involves the addition of a flocculant to the cyclone feed for the purpose of obtaining a clear cyclone overflow, and thereby eliminating or reducing thickener requirements in tailings disposal operations. This paper describes the testing of this concept on the iron ore tailings of Quebec Cartier Mining Company's Mount Wright Concentrator. The current practice at Mount Wright makes use of conventional hydrocyclones and thickeners for the disposal of their tailings, which are generated in a spiral gravity separation circuit. The test work was conducted primarily on their cyclone overflow product which becomes the feed to the thickeners. A detailed study was carried out to determine the sedimentation properties of these tailings in terms of their response to a variety of flocculating reagents, and to varying conditions of pH, pulp density and flocculant dosage. The tailings were then processed in a laboratory hydrocyclone with the aid of flocculants. The use of a shear resistant flocculant, in particular, was found to yield cyclone overflows with low solids contents. Based on the test results obtained, a conceptual flow sheet has been proposed for the treatment of the iron ore tailings at the Mount Wright Concentrator.

Jan 1, 2004

By Steve Kral

The concept of sustainable development is not new to the mining industry. Many people involved with mining have argued that the industry throughout the world has always supported the communities where they operated. They say that the mining industry was employing sustainable development practices before the phrase became fashionable. The mines employed residents and supported the local economy through tax payments and the purchase of goods and services from local businesses. In many cases, mining companies have built medical facilities and contributed money, equipment and services to local schools. In modern times, mining companies have donated reclaimed land to the local communities for use as parks and recreational facilities.

Jan 1, 2004

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Yuanbing Ling

Keywords: Calcium sulfate, Sulfuric acid, Phase transformations, Thermodynamic analysis As part of a boarder research project, seeking the development of a cost-effective process for direct production of the high value material, -calcium sulfate hemihydrate, from sulfuric acid at atmospheric as opposed to elevated pressure conditions, the fundamental work presented here has been undertaken. This includes experimental monitoring of phase transformation reactions and thermodynamic analysis of the relationships among the various phases, namely, calcium sulfate dihydrate, hemihydrate and anhydrite in aqueous sulfuric acid solution at temperatures ranging from 20oC to boiling point.

Jan 1, 2004

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By M. Pearson, W. Bristowe, A. Hanson

"There's no such thing as quality assurance; only quality control ... by inspection. "(1) A common misunderstanding in the procurement and construction of custom designed, fabricated pressure vessels and piping systems is that quality assurance can be achieved by simply referencing codes, standards, ISO 9002, QMS or other such programs in the contract documents. In the authors' experience, nothing could be further from the truth, not detrimental to the performance of the equipment than the exclusion of inspection activities and reliance upon warranties and "fit-for-purpose" clauses. Likewise, the expectation that fabricators, suppliers, or third party inspectors can provide such assurances is also unrealistic where they have limited knowledge of the process, material selection criteria, or limited technical resources. The development and successful execution of a quality assurance program is a collaborative effort by engineers, designers, material suppliers, equipment fabricators, and field inspectors with the full understanding and support of the end user.This paper presents an outline of the quality control activities undertaken by the authors for several recently completed and on-going hydrometallurgical projects. The activities include: prequalification of fabricators and sub-vendors, shop audits, material validation testing, material source control and verification, positive material identification of weld metal overlay, specialised welding inspection, contamination control for titanium and titanium-clad fabrication, eddy current and mass spectrometer (helium) leak testing of shell-and-tube heat exchangers, hot cycle testing of titanium clad equipment, tolerance verification for refractory lined equipment, final inspection and cleaning.

Jan 1, 2004

By J. C. Gathje

Newmont acquired the Phoenix Project through the acquisition of Battle Mountain Gold in 2000. Shortly after the acquisition, Newmont Metallurgical Services (NMS) and Nevada Operations began development work on a process to Pressure Oxidize (PDX) precious metal rich copper concentrates from Phoenix using the Lone Tree PDX facilities at Valmy, Nevada. The high precious metals content of the Phoenix concentrate - Au up to -300 g/t and especially Ag, up to -1700 g/t - led Newmont to the development of a High Temperature PDX process that achieves high cyanide leach recovery of Au and Ag, from the PDX solids, without the requirement for a messy and expensive "lime boil" or sulphate destruction process. Base metals content in Phoenix concentrates range from: 15-25 % for Cu, 1-10 % for Zn and 0-2 % for Pb. Excellent solution extraction of Cu and Zn is achieved while Pb is precipitated in the PDX residue. In addition to achieving high Au and Ag recovery this process produces very clean PDX discharge liquors that require minimum effort to remove contaminant metals and PDX solids that have superior settling and filtration characteristics. All of these factors contribute to lower capital and operating costs for the overall process. This paper describes the laboratory and PDX pilot plant developments for this process.

Jan 1, 2004

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003

By S. Nagamatsu

Alumina supported gold catalyst prepared by spray reaction method (spr) provides gold particle with about 20 nm of diameter. The gold particle size is larger than conventional gold catalysts. However, the spr catalyst shows higher catalytic activity for NO-CO reaction. In the present paper, we have discussed the local structures of spr-Au/Al2O3 catalyst by using Au L3-edge XANES spectra. In order to investigate the local structures of Au-sites, multiple scattering approach to XANES analysis was applied. Calculated Au L3-edge XANES spectra for fcc-Au and Au2O3 were in good agreement with the observed spectra. XANES spectra for spr-Au/Al2O3 were characterized by 4 types of Au sites (bulk, interface, surface and peripheral). In this case, almost all gold sites (> 90 %) are bulk site. The other sites are less than 10 % of gold particle. However, the experimental and the calculated results of Au L3-edge XANES spectra for spr-Au/Al2O3 require about 30 % of gold oxide or hydroxide. Bulk of Al2O3 contains a certain number of gold nano-particles, which was incorporated in the bulk Al2O3 support. In the interface area, gold oxide forms a few layers. This result was also supported by DV-Xa electronic structure calculations. The comparison of the catalytic activities of the spray catalysts and the impregnation catalyst for the NO-CO reactions imply synergy effects between gold nano-particles and alumina support.

Oct 1, 2003

By Paul J. Cascone

This paper will discuss the science behind the development of a unique gold alloy for dental prosthetic applications. The alloy (GOLDTECH BIO2000) contains 99.7% gold providing unquestioned biocompatibility and unsurpassed esthetics. The topics discussed are: (1) How the alloy meets the functional requirements of a porcelain-fused-to-metal dental alloy. (2) How the alloy color affects the esthetics of the restoration and why the color of gold is best. (3) Overcoming the intrinsic malleability of gold when grinding the alloy surface. (4) Preventing the oxide color from interfering with the alloy esthetics. (5) Attaining excellent porcelain adhesion. (6) How the design of the restoration allows for the production of single and multiple unit restorations. Gold 2003

Oct 1, 2003