Search Documents

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By Arthur L. Crawford

PLAGER gold is perhaps the most difficult of the common mineral deposits to evaluate. Not only are the erratic pay streaks a source of never-ending uncertainty, but the spotty distribution of the gold in iso¬lated nuggets is a perpetual source of error and disappointment to the sampler. Experienced engineers have long realized this difficulty and have been wary in predicting assay values except in the most general terms, and then only after extensive and usually expensive sampling. During the past year I have had the opportunity of checking a number of gold placers, and from the results obtained I believe that the microscope may be employed to advantage in placer sampling.

Jan 1, 1933

By J. W. Jamieson

"The future of the marine mining industry is tied to the resource potential of the seafloor. Everything from economic feasibility, policy decisions and environmental impact assessments to extraction techniques and mining tool design rely on an understanding of the size, composition, and distribution of the deposits. Development and regulatory decisions must ultimately be tied to not only the grade and tonnage estimates of individual deposits or groups of deposits, but also an understanding of the uncertainty of these estimates. Here, we will discuss how seafloor massive sulfide (SMS) deposit grades and tonnages are evaluated, and the sources of the uncertainties associated with these values.TONNAGE UNCERTAINTYFirst-order tonnage (size) estimates for SMS deposits are primarily determined from calculating the volumes of material that occurs as positive bathymetric features on the seafloor. The extent of sulfide mineralization on the seafloor can be determined either from visual surveys (camera-tow, remotely-operated vehicle (ROV), or human-occupied submersible surveys) or from volume calculations of bathymetric features identified from digital elevation models of the seafloor, or a combination of both methods. For bathymetric models to be used to identify deposits in the absence of visual groundtruthing, data resolution of 1 m or less is generally required to confidently identify a feature as being hydrothermal in origin (as opposed to a volcanic or tectonic feature), and therefore near-bottom multibeam data acquisition (e.g., using autonomous underwater vehicle (AUVs) or remotely operated vehicles (ROVs) is required (Fig. 1). Specific characteristics of bathymetric features, such as shape, slope angles and surface roughness can be used to identify features of hydrothermal origin (Fig. 1). However, so far, bathymetric features mapped at a resolution of ~1 m cannot be relied upon to unambiguously distinguish a sulfide mound, and the additional use of multiple AUVmounted sensors, such as magnetometers, which can be used to detect hydrothermal upflow zones, or self-potential sensors, which detect electrical fields related to the oxidation of sulfide minerals, can increase the confidence that a bathymetric feature is indeed a sulfide body, without the need for expensive and time-consuming visual surveys (c.f. Petersen et al., this volume)."

Jan 1, 2017

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

By N J. Arunakumaren

A coal mine is proposed for an area where a major river traverses the project area. There were initial concerns that inflow of groundwater from exposures of high permeability alluvium associated with the river system could pose mine dewatering problems together with adverse impacts on surface water resources in the river. The project included collation and analysis of geological and hydrogeological data collected historically over a long period of project investigation and evaluation. The project also included establishment of additional groundwater monitoring points to provide a reliable groundwater contours. The groundwater level contours were produced to allow numerical models to be calibrated to support estimation of groundwater inflow. River bed cross sections were also prepared to assist study of the effect of river flow on the inflow. Two separate MODFLOW groundwater models were produced to simulate long-term groundwater inflow to the mine with an upper model consisting of the Quaternary and Tertiary alluvium lumped together and a lower, separate model consisting of Mesozoic coal measures. Analytical solutions were used to predict initial inflow from the alluvium and from the coal measures.

Jan 1, 2003

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By Wei Wei

Mining induced ground movement and/or stress redistribution could cause ground instability issues. This is particularly true when the extraction of large stopes is done with one or two large production blasts. Often enough, it is the nearby mine development like haulage drifts and cross cuts that are influenced the most by production blasts. Proper and timely mitigation of ground control issues due to stress redistribution is required. This is usually done by drift rehabilitation involving the installation of secondary support system in the affected areas of the mine development which include; slashing, wire mesh, and in some cases the use of shotcrete liners. It is imperative that such rehabilitation be implemented to the mine infrastructure in a timely manner in order to avoid aggravated ground control problems and production delays. If the real time performance of the support system is captured, it would be possible to determine the timing for rehabilitation job. Birchtree Mine in Thompson, at the Vale Manitoba Operation, has begun mining the 84 Deep Orebody. One of the identified risks is the stability of the crusher room under mining induced stress redistribution. It is proposed to use the U-Cell technology to monitor the primary support system performance (rebar bolts and extension bolts) and monitor the real time performances of the bolt axial loads. The U-Cell technology is a 7-inch long, coupler load cell that is screwed onto the threaded portion of a rock bolt prior to installation. Rehabilitation in the vicinity of the crusher area where U-Cells are installed is recommended when the bolts have reached 70% of their yielding capacity. Catastrophic ground failure can be avoided by adding secondary support in a timely fashion. This paper presents a case study at Birchtree Mine in Thompson Manitoba, where the performance of primary ground support system is monitored and recorded during production.

Jun 1, 2012

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By Robert L. Brooks

This paper is intended for companies at all levels of the Explosive Industry and in particular, those that do not have a risk manager. It is strictly informational in nature and no reference is made, or intended towards any existing insurance company or agency.

Jan 1, 1993

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By J. P. Rider

Health surveillance efforts indicate that the development of lung disease and overexposure to respirable dust in underground coal mires continues to afflict mine worker. Results from the most recent round (1992 - 1996) of the Coal Worker's X-ray Surveillance Programs indicate that approximately 8% of the examined miners who had at least 25 years of mining experience were diagnosed with Coal Worker Pneumoconiosis (CWP) (category 1/0+). During the period between 1995-1999, mine operators and MSHA inspectors collected 9968 and 1365 dust samples respectively, from longwall designated occupation (DO) personnel. Analysis of these samples showed that 1970 (20%) of the mine operator samples and 25.8 (19%) of the MSHA samples5 exceeded the 2 mg/m3 dust standard. The continued development of CWP in coal mine workers and the magnitude of respirable dust over-exposures in longwall mining occupations illustrate the need for improved dust control technology on longwalls. Figure 1 illustrates the major longwall dust sources as determined in the early 1990's.4 This article describes the ongoing research to find ways to minimise shearer dust levels as a function of changes in dust control parameters, and research to determine the impact of high air velocities on shield dust entrainment.

By Joseph M. Denk, Gary J. Wirth

This paper summarizes a three phase face ventilation study which was conducted from September 1989 through March 1990 to determine face area methane liberation patterns on two extended longwall sections. The coal seam being mined was considered gassy and the mine liberated an average of 14.4 million cubic feet per day (cfd) or 0.41 million cubic meters per day (cmd) of methane through the mine fans. The mine also used an extensive underground degasification program to recover up to 13.4 million cfd (0.38 million cmd) of methane. Data was collected while the longwall sections were mining from the beginning, middle and end of panel extraction to determine the relationship between the methane liberation and extent of longwall retreat. As expected, methane concentrations did increase from the headgate (intake) to the tailgate (return) side of the longwall face and peak concentrations were detected above the shearer as it passed a methanometer location during mining. There were significant differences in the methane liberations due to the location of the active face within the longwall panel. Results from this study could be used to determine a minimum design face air quantity for an extended longwall section operating under similar conditions.

Jan 1, 1991

By F. Milton Lewis, Roshan B. Bhappu

In Part I of this article, published in the September issue of MINING ENGINEERING, Edward S. Frohling and Robert M. McGeorge of Mountain States Mineral Enterprises, Inc., reviewed the general overall financial aspects and methods of raising the necessary capital for developing the mine. In Part 2 of this two-article series, we will present several case histories to show how realistic feasibility studies are used for evaluating the choices and options entailed in mining ventures. Basically, after a potential ore body has been discovered, and the necessary funds obtained for the development of the deposit, the next major problem is one of ascertaining what specifically is to be produced, and the costs of production. The profit potential of the mining venture can then be accurately assessed by the mine owner, operator, or loan officer.

Jan 10, 1975

By Bruno Lemelin

Falconbridge Ltd Raglan Mine has been in production since 1998 and has produced annually some 900 000T of ore grading 3.1% nickel, 0.9% copper and 0.06% cobalt. The mine is located in Nunavik, Northern Quebec. The current mine life is estimated at approximately 20 years. Reserves are composed of numerous small ore bodies situated across a 65 km strike length. Planning the extraction of the ten small mineralized zones represents a great challenge to optimize. The overall objective is to maximize the company?s return on net assets. Actual planning uses computerized technology tools like Automod and Mine2-4D, and a conventional discounted cash flow method (DCF) of calculating net present value (NPV). The complex setting of Raglan could benefit from advance valuation techniques such as the real options method (RO). This paper will present the characteristics if the mines that make it a good candidate to use RO to gain further insight.

May 1, 2004

By Michael Moats, Adirek Janwong

The use of cylinder electrowinning cells, such as emew® technology, for the recovery of silver from primary and secondary sources has been growing. In this study, common operating parameters used in silver electrowinning were evaluated for recycling applications. Silver powders were produced from an industrial solution in a laboratory scale emew® cell. A design of experiments was employed to evaluate the effects of HNO3 concentration, iron concentration, current density and solution flow rate on current efficiency, particle size, bulk density, and crystallographic orientation. Current efficiency was affected by each parameter with increasing HNO3 concentration having a strong negative effect, increasing iron concentration and current density having moderate negative effects and increasing flow rate having a positive effect over the ranges examined. Finer particles were produced with increasing current density and decreasing flow rate. Bulk density increased when HNO3 concentration increased. The crystallographic orientation of all powders was dominated by the (111) plane. Increasing flow rate decreased the relative intensity of (200) direction. Based on these observations, silver electrowinning in cylindrical cells can operate at high current efficiency and produce larger powders at low HNO3 concentration, low iron concentration, low current density and high flow rate.

Jan 1, 2014

By S. Garcia, J. Gebhardt, D. McBride, A. Hernandez, A. Esplín, M. Cross

The Minera Yanacocha operation consists of several heaps interconnected with ponds and gold recovery plants and presents various operating challenges. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters and inventory issues. An integral component of the process water/mass balance is a model of each heap that describes heap behavior based on the individual characteristics of the heap. The heap models are linked to a mass balancing program in order to track flows and concentrations throughout the circuit. A case study of the process heap model is presented for the La Quinua heap, including results for the normal base line operation and several operational problems such as loss of solution flow to the heap (i.e., pump failure), increased flow to a section of the heap (i.e., pond volume control), effect of significant rain events, and impact of a change in material properties (i.e., change in ore type). The impact on heap operating efficiency is discussed with regard to effects on recovery and gold solution grades.

Jan 1, 2007

By Dominick Mandalari, David Mast, Heather Ullinger, Juan Granja, Amanda Foote

The City of Akron will construct the Northside Interceptor Tunnel (NSIT) project to control and reduce combined sewer overflows. One component of the project a large diameter tunnel diversion / flow control structure that will facilitate tunnel storage, divert dry weather flow to the treatment plant, and divert large wet weather events that are greater than the tunnel capacity to the Cuyahoga River. The structure is designed to pass up to 1.2 billion gallons per day of flow and includes floatables screening. This paper will discuss project background, factors that influenced shaft location, and options evaluated to manage the large design flows.

Jun 23, 2024

By Peter G. Chamberlain

Many mining engineers considering in place leaching for the first time are uncertain as to how to evaluate ore bodies for potential leachability. Evidence presented in this report emphasizes the critical role of permeability in such evaluations. Whether an engineer is considering leaching "tight" formations typified by the porphyry copper deposits of the southwest or the permeable uraniferous sandstones of Texas and Wyoming, permeability measurements are the keystone of any testing program. Permeability tests range from cheap and easy to highly expensive and sophisticated operations. Constant head, variable head, and pumping tests all have application in evaluating ore bodies for in-place leaching. Costs of these tests will not unduly deflate the pocketbooks of most mining companies. The basic procedures for selecting and running these field tests--including preparing suitable wells--are reviewed for the benefit of newcomers to in-place leaching.

Jan 1, 1979

By Peter G. Chamberlain

Many mining engineers considering in-place leaching for the first time are uncertain as to how to evaluate ore bodies for potential leachability. Evidence presented in this report emphasizes the critical role of permeability in such evaluations. Whether an engineer is considering leaching "tight" formations typified by the porphyry copper deposits of the southwest or the permeable uraniferous sandstones of Texas and Wyoming, permeability measurements are the keystone of any testing program. Permeability tests range from cheap and easy to highly expensive and sophisticated operations. Constant head, variable head, and pumping tests all have application in evaluating ore bodies for in-place leaching. Costs of these tests will not unduly deflate the pocket- books of most mining companies. The basic procedures for selecting and running these field tests-including preparing suitable wells--are reviewed for the benefit of newcomers to in-place leaching.

Jan 1, 1979