Search Documents

By Bing Song, Fei Xi, Xuewei Lv, Kai Zhang

The electric arc furnace process is a common method to produce high TiO2 slag from ilmenite. The pre-reduction process was proposed in recent years in order to reduce electricity consumption. In order to enhance the pre-reduction degree, high energy ball milling was proposed to improve the specific surface area of the ilmenite prior to reduction. In this study, the carbothermic reduction behavior of milled ilmenite concentrate was investigated. It was found that the ball milling method can result in a higher reduction rate and improved metallization of iron. The metallization of iron increased with increasing the time of ball milling. The metallization of iron with milling reached 89.49% when the time of ball milling was 70 min., while the FeO content decreased with 70 min. of milling from 11.84% to 4.76%.

Jan 1, 2014

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994

By Mei Song, Qingyu Deng, Xuewei Lv, Lu Liu, Chenguang Bai, Meilong Hu

"The carbochlorination of several silica materials was carried out in the temperature range from 900 °C to 1200 °C. In this study, silica oxides and gaseous chlorine with carbon as reductant were used. The optimal carbon silica mole ratio in different temperature was calculated by Factsage software and the results showed that the optimal values are 1.2, 1.4, 1.6, 1.8 at 900 °C, 1000 °C, 1100 °C, 1200 °C, respectively. According to the experiments, the chlorination ratios of several silica materials were increased with temperature increasing. In the same temperature, the chlorination ratio of diatomite is the maximum and the chlorination ratio reaches 79%% when C/SiO2 reaches 3 at 1100 °C.1, IntroductionPolycrystalline silicon is the main material to manufacture the silicon polished section, solar battery[1] and high purity silicon wafers[2], also which is the most basic function material of semi-conductor industry, electronic information industry and solar photovoltaic battery industry[3]. The conventional manufacturing process of polycrystalline silicon would be divided into three parts: the improved Siemens method, which was introduced and became the main process to produce the polysilicon products in China. Silane method and fluidized bed method. Silicon tetrachloride and chlorosilans have been employed as by-products in several fields like electronic, telecounications and metallurgy[4-6]• At present, the main applications of silicon tetrachloride include production of trichlorosilane by catalytic hydrogenation, synthesis of fumed silica and ethyl orthosilicate, production of optical fiber grade silicon tetrachloride.The conventional routes for the silicon tetrachloride production have been reported, including the direct chlorination and the chlorination process of ferrosilicon, abandon catalyst and silica[7]."

Jan 1, 2013

By M. Z. Mubarok

Effect of single addition of a lignin-based biopolymer additive, DP 2782, at various dosages as well as in combination with thiourea on cathode polarization during copper deposition was investigated by performing potentiodynamic and galvanostatic measurements using a potentiostat. The result of electrochemical measurements was compared with the behaviour of cathode deposition with glue and thiourea additives. Surface micro-appearance of the copper deposit after 1 h galvanostatic scan under current density of 330 A/m2 and various additive type and dosage was evaluated by scanning electron microscopy (SEM) examination. It was found that the addition of 2.5 mg/l biopolymer gave sufficiently polarizing effect of copper deposition. SEM examination of the cathode surface after galvanostatic scan revealed that the combination of the biopolymer with thiourea (2.5 and 3.5 mg/l) resulted in a compact deposit which is comparable with that resulted from the test with glue and thiourea.

By Hiroshi Maeta, Takao Kino, Hirota Osono, Kikuo Matsusaka, Azusa Shida

"Prior to refine an ultra-high purity material, it is necessary to estimate the surface cleanness of a base material. In this report, the cleaning method of a surface for refining of an ultra-high purity aluminum has been studied. Aluminum sample of 99.999% purity was p9lished mechanically and electrically and washed with various solvents. Surface composition and a depth profile near the surface were examined. Based on the experimental results, surface structure of an ultra-high purity aluminum was discussed.IntroductionRecently, studies on high purity metals have become of interest, and we have reported .various properties of an ultra- high purity aluminum1- 2)In order to purify a metal, it is necessary to clean a work area and to make vacuous as possible. So, we are studying the purification of aluminum by an ultra-high vacuum refining system and a zone refining system set up in a clean room with cleanliness class of 1000.Now, in order to avoid a mixing of impurities into the refining metal, a surface cleanness of a base metal is very important factor. The purity of the base aluminum used our work is 99.999%, but the surface state of the base aluminum is not clear. Aims in this work .are to investigate the surface state and to obtain the cleaning method of the base aluminum.Experimental procedureSamples used in this work were 99.9% (3N), 99.99%(4N) and 99.999% (SN) aluminum produced industrially and 99.9999% (6N) aluminum purified by us."

Jan 1, 2000

By S. S. B Wang

Zirconia-based ceramic materials have potential applications in high temperature furnace insulation, hot extrusion and casting dies, pressure nozzles, cutting tools, engine parts and electronic materials. High purity and superfine powders of zirconium oxide (baddelyte) were synthesized from a solution containing zirconium oxychloride and urea under hydrothermal conditions. crystallization of the metastable tetragonal zirconia using magnesium oxide or yttrium oxide as stabilizing agents was successfully achieved. The mechanism of hydrothermal reaction to produce these powders are discussed.

Jan 1, 1989

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Ann M. Hagni

Electric arc furnace (EAF) dust from the secondary steel industry contains lead, cadmium, and chromium that causes it to be classified as a hazardous waste. Pyrometallurgical treatment of EAF dust is directed at recovering zinc and simultaneously rendering the dust non-hazardous. The mineralogy of the EAF dust is important in determining the occurrence and phase relationships of the zinc, lead, cadmium, and chromium contents. The principle phases in EAF dust as determined by reflected light microscopy, SEM-EDS, and XRD are solid solutions of the iron spinels (franklinite, magnetite, and jacobsite), zincite, hematite, and Ca-Fe-Si glass. Chromium is present in small amounts in solid solution in the spinels. Cyclone sizing of the minus 53 pm particles shows that more than 50% of this size fraction are less than 10 pm in diameter. The <I0 pm particles contain zinc as both franklinite in solid solution with magnetite and jacobsite, and zincite as determined by transmission electron microscopy and XRD. Auger electron spectroscopy did not detect coatings of volatile phases on the surfaces of EAF dust particles.

Jan 1, 1994

By Shigem Kuramoto

Pure copper is known to exhibit intermediate temperature embrittlement when it is deformed at a slow strain rate, and a small addition of zinc suppresses this embrittlement. In the present study, the relation between zinc addition and hydrogen behavior was taken into account since the impurity hydrogen is believed to deteriorate the ductility at intermediate temperatures. Pure copper and Cu-l mass % Zn alloy specimens are prepared by melting in argon and in vacuum, so that a comparison can be made between the specimens with normal hydrogen content and those with&apos; less hydrogen content. Tensile tests are performed at temperatures ranging from room temperature to 600 "C, and hydrogen behavior is analyzed using a newly developed testing machine that can detect gas evolution from the specimens during deformation and fracture in ultra high vacuum. The small addition of zinc to pure copper decreases hydrogen content, leading to the improved ductility at intermediate temperatures. In addition, the samples of both pure copper and Cu-1%Zn melted in vacuum exhibited higher ductility at intermediate temperatures than those melted in argon atmosphere, which is attributed to reduced hydrogen content.

Jan 1, 1998

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By S. H. Amini

The effects of CaF2 and ilmenite on dissolution rate and diffusivity of CaO in calcium alumino-silicate based slag in a temperature range of 1500 ? 1600 ºC were studied by using the rotating disk/cylinder technique. The effect of rotation speed on the rate of dissolution in the base slag indicated that mass transfer in liquid slag played a significant role in controlling the dissolution. At a constant rotation speed, the effect of 5 wt% addition of fluxes tothe slag on the dissolution rate was investigated at various temperatures. While CaF2 had the highest effect, addition of ilmenite increased the rate of dissolution significantly. The diffusivity of lime in these slags was quantified using the dimensionless mass transfer correlations for rotating disk/cylinder in the melt. The diffusivity values were deduced using the data on dissolution rate and solubility of lime in the slags. The measured diffusivity in base slag at 1500 C was found to be about 1.32 10-5 cm2/s and increased to 3.07 10-5 cm2/s at 1600 °C. Addition of 5wt% CaF2 increased the diffusivity by a factor of 3 to 5, while 5wt% ilmenite increased the diffusivity by a factor of 2 to 3 in the temperature range of 1500 to 1600 ºC. The two examined fluxes reduced the activation energy of diffusion.

Jan 1, 2006

By Ray Y. Lin

This study explores the formation of sodium pyrosulfate in molten sodium sulfate resulting from dissolution of SO3 at temperatures between 1160 and 1250 K. Solubility of SO3 in Na2SO4 melts at temperatures between 1160 and 1250 K under gas mixtures of SO2, O2 and argon was investigated applying a thermogravemetric analysis (TGA) technique. The activity of Na2O in the melt was determined with a high temperature electrochemical cell (ECC). Results showed that the SO3 solubility in molten Na2SO4 increases with decreasing temperatures and increasing SO3 partial pressures. Enthalpy of SO3 dissolution in molten Na2SO4 was calculated to be -119 kJ/mol for infinite dilute solutions. Thermochemistry of Na2SO4-Na2S2O7 melts was analyzed based on information obtained from both TGA and ECC techniques. Detailed examinations of the earlier low temperature measurements in the Na2SO4-Na2S2O7 system along with data from this study reveal that the solution behavior between Na2SO4 and Na2S2O7 can be satisfactorily treated as regular with the interaction parameter, , being 2.7 kJ/mol. The phase diagram and the field of SO3 partial pressure has been generated with the thermodynamic calculation using a regular solution approach.

Jan 1, 2006

By Evan Jamieson

The conditions under which various iron(III) oxy-hydroxides phases precipitate from iron(III) chloride and sulfate solutions at ambient temperatures (<60°C) are reviewed. Many of these precipitates are slow settling and gelatinous but ultimately transform into other more stable or crystalline phases. The phase that forms depends upon the rate of precipitation and pH. A comparison has been made of the iron(III) oxides formed upon the neutralisation of various iron(III) solutions with caustic, slaked lime or slaked magnesia which provide different rates of neutralisation and slowly dissolving solids with localised high pH. Mössbauer spectra of ferrihydrites precipitated under these different conditions are compared and interpreted. Particular attention is paid to the settling rate and settled volume which is likely to relate to industrial thickener and filter performance. It is shown that in pure chloride solutions, poorly settling ferrihydrite is usually produced at 20oC regardless of the choice of base. However in sulfate solutions fast settling precipitates are produced using lime and magnesia but not with caustic. In mixed chloride/sulfate solutions, optimum settling rates occur when the molar ratio of [SO4]2to Fe3+ is about 1:1 and when the sulfate concentration is <0.20 M. It is proposed that ?dense amorphous basic iron sulfate? or well-ordered ferrihydrite is formed on slowly dissolving lime or magnesia surfaces. Implications for industrial liquors are considered.

Jan 1, 2003

By Peter Koh

The velocity solid charge attains when dropping down concentrate chutes is an important boundary condition when developing mathematical models of flash furnace burners and reaction shafts. In this work an experimental rig was developed to measure the velocity attained when nickel concentrate and sand were dropped down a vertical pipe 3m long. The velocity measurements showed that the nickel concentrate did not fall as individual particles. The measured values of the velocity approached, but did not attain, those calculated for solid bodies, the disparity being attributed to friction at the pipe wall and fluid drag losses. After falling 2 m velocities between 5-6 m/s were attained. The analysis was extended and applied to understanding the intermittent problem of puffing which sometimes occurs from the top of the concentrate chute. The pressure at the bottom of the chute is the net result of two opposing pressures, namely that developed by (a)the process air entering through the velocity control device, and (b) the solids falling down the concentrate chute. Flow back up the chute occurs when the former exceeds the latter. The process air pressures in the burner were obtained from CFD simulations of a full burner. Variables considered included air speed through the velocity control device, drop height and furnace draft. The analysis was useful in highlighting the operating conditions which were conducive to puffing and in establishing procedures to minimise its occurrence.

Jan 1, 2006

By E. Almendras de Siegel

Pyrometallurgical processes have the thermodynamic capability of treating complex and dirty ores and concentrates to produce high purity metals and inert slags. Modem pyrometallurgical processes are environmentally sound and competitive with other processes. However, there is still a need for sensors and other practical tools that permit a rapid evaluation of the performance of these processes. In order to contribute to satisfying this fundamental requirement, the authors developed the IDENT.LA software that permits the automatic mineralogical analyses of inorganic materials, including the final and intermediate products of pyrometallurgical processes. The technique allows determining the grain size distribution of mineralized inclusions, the surface relations between metallic phases, and conducting modal analyses of the essential phases that are present in the samples. Three basic automatic operations are performed: creating a representative image of the sample; identifying the metallic and non-metallic phases; and measuring the features of the resulting image. The results are used to evaluate the performance of pyrometallurgical and other processes. In this paper, the authors discuss the application of the technique to a sample of slag from a slag cleaning process that uses a carbonaceous reductant. In this case, process performance impacts not only on the efficient reduction of the slag magnetite and on copper recovery but also on the quality of the process off-gas. The mineralogical analysis of the slag is a valuable tool in assessing process performance and in recommending changes of operating conditions.

Jan 1, 1999

By Joo Hyun Park

A history of the research regarding the spinel in the community of the stainless steels has simply been reviewed, followed by the recent studies for the formation mechanism of the spinel in the ferritic stainless steel melts equilibrated with the highly basic slags and the crystallization behavior of spinel phase in the calcium aluminosilicate melts containing MgO and CaF2 during slow cooling cycles. It has been proposed that the content of aluminum and calcium in the steel melts as well as the basicity and the content of MgO and Al2O3 in the slags are quite important factors affecting the spinel formation in view of the formation mechanism based on the reduction of MgO (or CaO) and Al2O3 in the slags by the aluminum and silicon added to deoxidize the molten steel. The use of magnesia refractory was also recommended. The formation mechanism of spinel from the MgO inclusions readily formed in the steel melts equilibrated with the highly basic slags has newly been proposed on the basis of the ionic exchange reactions at the inclusion/metal interface and the crystal chemistry of oxides. The crystallization behavior of the spinel phase in the calcium aluminosilicate melts was enhanced by the Al2O3 based on the ionic reaction of spinel formation in the oxide melts, while the size of the spinel crystals in the oxide melts decreased by addition of CaF2.

Jan 1, 2006

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012

By Denise C. R. Espinosa

The amount of secondary batteries are increasing about 15% by year. Among these batteries, it can be highlighted the NiCd ones, due to their high consumption. In Brazil, the consumption of NiCd batteries grown quickly in the last 5 years, due to the dissemination of cellular telephones and other electronic devices. The first step of a process to recycle spent NiCd batteries is the pretreatment through unit operations of mining treatment. The aim of this work is to define a physical pretreatment to conditioning the waste to a pyrornetallurgical recycling process of spent NiCd batteries used in cellular telephones. Batteries were disassembled by hand to release the different components. The studied batteries are basically composed (by weight) of: 78% nucleus, 18% plastic case and 2% circuits. The grinding of the batteries was performed by knife mill and also by hammer mill. After grinding the material was screened and submitted to a magnetic separator.

Jan 1, 2001

By Alex I. Kociubczyk, Wilky Desrosin, Lucía Mabel Boycho, Alicia E. Ares, Carlos E. Schvezov

In the present research, commercially pure Sn and Zn, and Sn-Zn alloys (Sn-1wt.%Zn, Sn- 2wt.%Zn, Sn-4wt.%Zn, Sn-8wt.%Zn and Sn-8.9wt.%Zn, weight percent) were obtained by a horizontal directional solidification process with two opposite senses and heat extraction. The solidification process was realized using a horizontal furnace with two heat extraction systems at both ends. The temperature was measured using eight K-type thermocouples and an electronic recorder of temperature data. The resulting structures were analyzed using optical microscopy. From the solidification process the thermal and metallographic parameters were determined in all samples. The presence of defects in the solidified pieces was observed. Internal defects pretended to be dependent not only on the composition of the alloys under consideration but also on the size of the structures formed, also, on the velocities and accelerations of interphases, and on the variation of thermal gradients. A model of the phenomenon from the first principles is presented.

Jan 1, 2015

By Chang Wei, Zhigan Deng, Yizhao WANG, Cunxiong Li, Gang Fan, Xingbin Li

During the process of hematite precipitation, the transformation of Na jarosite convert into hematite has been studied in a batch reactor at different temperatures, ranging from 170°C to 200°C with 3h of the retention time in the presence of 30g/L Fe ( ) and 4g/L Na+. The composition of precipitation was seriously depended on the temperature, at 170°C hematite and sodium jarosite are the reaction products of iron precipitate, with an increasing in reaction temperature the sodium, sulfur content in precipitated decreased and sulfur mainly exist in forms of SO4 2-, and when temperature over 200°C hematite was the only phase in product. An increasing temperature was not only beneficial to iron precipitation, also conducive to jarosite conversion to form high quality hematite precipitate.

Jan 1, 2016