Search Documents

By Sang-Su Lee

This paper shows the application of the porous plug system in the Mitsubishi continuous copper smelting and converting process. This system has already been adopted and utilized in the steel industry to enhance productivity. Recently, some copper smelters have adopted this system but the results have not been satisfactory. The porous plug system was installed at the anode furnace in December 2001 to reduce the oxidation time and decrease the oil consumption. A good effect was that the nitrogen stirring of the melt through porous plugs improved the melt heat transfer. As the result of the enhancing heat transfer the oil consumption and the build-up inside the furnace were actually decreased. But until now the oxidation time has not been sufficiently reduced. In the future, further research and tests are needed in order to increase the productivity and save costs.

Jan 1, 2003

By Yuuki Hagio, Hiroyuki Tobo, Michihiro Kuwayama, Yasutaka Ta

"Reduction of CO2 emission is necessary to remedy global warming, however, promising approaches of CO2 separation require a large amount of energy. Molten slag, which is generated as by-product of steel production, has high temperature, but its energy has not been harnessed. To recover the thermal energy from the slag and to apply to separation of CO2 are economical and environmental conscious ways. We propose a new heat recovery system, in which, molten slag is solidified continuously on water-cooled roll and the solidified slag plates are charged into counter-current heat recovery equipment. In laboratory scale experiments, heat recovery ratio of more than 30% was acchived by controlling the thickness of slag.IntroductionThe steel industry in Japan has been working on the projects of ""Environmentally Harmonized Steelmaking Process Technology Development (COURSE50)"". COURSE50 aims at developing technologies to reduce CO2 emissions by approximately 30%. One of the main technologies is to capture and recover CO2 from blast furnace gas using chemical absorbents to regenerate CO2-laden chemical absorbents by separating CO2 from the absorbents. As one of the solutions, JFE Steel Corporation has been developing sensible heat recovery process from steelmaking slag. It is effective to recover and use unutilized high temperature waste heat within a steel plant as the thermal energy required."

Jan 1, 2012

By Zhang Jianliang, Xu, Zuo, Runsheng, Haibin, Kexin, Jiao

Full oxygen blast furnace iron-making is one of the new technologies, which is most likely to realize large-scale application. In this paper, based on the technology of full oxygen blast furnace, the reduction behavior of pellets is studied systematically by using the analytic method of non-isothermal dynamics on the different atmosphere(CO,H2) and the dynamics model of gas-solid reduction reaction is constructed, which lay the foundation of reduction model establishment of full oxygen blast furnace burden. The result shows that the time of pellets which began to react is delayed with the increase of the content of H2. When the temperature is between 650 'C and 1050 'C, the content of H2 in the reduction atmosphere is larger, and the rate of the reduction pellets is larger. The reduction rate changes at 780 'C, and a certain amount of H2 in the reducing atmosphere will significantly improve the reduction reaction when the temperature is above 780 'C. Non-isothermal reduction behavior is controlled by interfacial chemical reaction and internal diffusion under high reduction potential. H2 ratio in reducing atmosphere increased from 0% to 100%. The reduction reaction of the apparent activation energy decreased from 49.03kJ-mor1 to 33.74kJ·mor1.

Jan 1, 2013

By Peter Willbrandt

The flash smelter at NA was commissioned in March 1972 with an initial throughput of 50 tons of dry copper concentrate per hour. As a result of various measures, for example, oxygen enriched process wind, extension of the radiation part of the waste heat boiler, etc., the throughput could be increased to the present 70 tons per hour of dry concentrate. NA's plant is located on the outskirts of the city of Hamburg. The flash smelter's location and the growing awareness of the German population as regards environmental issues necessitate again and again considerable capital expenditure being spent on environmental protection. Thanks to the numerous small and large measures taken to protect the environment the emissions of dust, heavy metals such as arsenic, copper, lead, etc., and as well SO, could be drastically reduced. This paper will be giving an overview on the present state of the flash smelting process and the impact of the increasing environmental awareness at NA.

Jan 1, 1993

By Shigehisa Endoh, Hitoshi Ohya, Atsushi Inaba, Shigeki Koyanaka

"Recycling should be promoted to keep the global environment. However, it is difficult to detennine the quantitative impact. A life cycle assessment is one of the most reliable methods to estimate the global environment impact.Exergy is useful like entropy when considering the sustainable development. All of our activities have been obtained exergy resources and/or energy itself and throw away waste and/or waste heat. We are trying to use exergy to estimate the quantity of energy and matter for resource accounting. For recycling plastic, plastic has two aspects; material and energy source.The environmental assessment of plastic recycling suggests that the exergy reduction of the entire system is estimated by the yield of matter and the process efficiency. The material recycling is better than the thennal recycling when the process efficiency is high. However, the thennal recycling is much better for the low efficiency. The transition point is able to be decided by the efficiency of the manufacturing and the electric power generation.IntroductionRecently, many of the global environmental problems have become conspicuous like global wanning, ozone layer depletion and acid rain. Some of the methods like life cycle assessment for solving these problems have been presented. Anxiety concerning the proble1ns of energy and resources has led to a rapid increase in the interest in describing and understanding the conversion processes of energy and other resources in today's society. All human activity is supported by obtaining power and products of high exergy from the environment and throwing away the waste material and the waste heat of low exergy back the environment. However, the total exergy in the whole system becomes absolutely smaller than before.The rate of obtaining high exergy products and energy itself by human activity and the speed, by which waste and waste heat having low exergy are thrown away are too fast to attribute to environmental problems [1-3].A material's use by recycling was often common in a circulating society mainly. A significant amount of energy is consumed during circulation. An environmental impact assessment method for the process or the system has not been devised when both of them are taken into consideration. Even if the life cycle assessment evaluation, which has been correctly used up to now, is applied, it is not sufficient for an overall evaluation concerning matter and energy.The real sustainable development is that the exergy reduction value by all human activities on the earth is kept within the range of the exergy reduction in order to consider the earth as closed stationary system. It is important to evaluate the process or the system by using the exergy, and design them so that the exergy loss may decrease as much as possible. We have to consider what process improvement is the most effective."

Jan 1, 2000

By Thomas Niehoff, Dave Stoffel

"Energy in the form of natural gas, oil and electricity is expensive and will continue to be a rare resource in the future. Recycling of metals, instead of primary production, is a logical and crucial step towards energy conservation. Energy consumption can be impacted by using advanced combustion systems for metals recycling. Air-fuel combustion has been the conventional method to melt and recycle metals. Global competitive pressures, “greenhouse” gas emissions, and high energy prices force melt shop operations to optimize energy usage and reduce overall operating costs. Oxy-fuel combustion and process technology can be applied to metal recycling operations to meet these objectives. Linde has converted several hundred furnaces from air-fuel to oxy-fuel technology and has extensive experience in optimizing the use of oxygen in furnaces. Additionally, Linde has the process knowledge necessary to avoid costly start-up issues that can accompany the transition to oxy-fuel technology. This paper will describe the benefits and potential issues for conversion to oxy-fuel.IntroductionThe furnace combustion system is the heart of a fossil fuel fired melting process and must be properly matched to the furnace to work as one cohesive unit. Furnaces vary widely in size, shape and features. Rotary furnaces are barrel-shaped and can be designed for tilting or nontilting operation. In a rotary furnace, the products of combustion create a single or double pass through the furnace prior to exiting. Reverberatory furnaces are box-shaped and can also be designed for tilting or non-tilting operation. Reverberatory furnaces are constructed of single or multiple chambers, with or without metal bath movement, and designed for continuous or batch processing. Different furnaces are used for different feedstock materials and products.Furnace combustion systems also vary in many ways. Combustion systems can be of air-fuel or oxy-fuel based technologies, or a combination of the two, resulting in an air-oxy-fuel system. Each of these types of systems has different combustion characteristics which can produce very different results. Here we will describe specific differences in melting processes and their associated energy requirements."

Jan 1, 2009

By Marcelo Jimenez Bustos

The Chagres Smelter was the first in Chile to follow environmental regulations to control sulfur dioxide emissions. Because of this, the operation and development plans have had to incorporate environmental planning as part of its policies for almost three decades. The present article shows the development of the environmental standards applied to its operations, investments and operational improvements carried out to meet the regulations and improve competitiveness. Results to-date and future plans are outlined, as well as their impact on operations and the environment.

Jan 1, 1993

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

The wettability behavior of graphite with silicon is a key factor for its application as a crucible in silicon making industry. A previous study was carried out to determine the correlation between the physico-chemical behaviors of different types of graphite and the final contact angle for the graphite/silicon system. In this study, experimental vacuum annealing treatment by varying the exposure time at high temperature of 1000 °C processed by X-ray photoelectron spectroscopy and SEM analyses enabled to found a correlation between the oxygen content in the graphite and the final contact angle for the graphite/silicon system. Finally, the experimental results with and without vacuum annealing treatment have shown that a deep infiltration of silicon inside the graphite occurs in case of high level of oxygen content inside the graphite’s pores.

Mar 1, 2017

By E. C. L. Cardoso

Hydrocarbon polymers, as PP, made from cheap petrochemical feedstock are important in many branches of industry. However, they have an undesirable influence on the environment and cause problems due to waste deposition and utilization. Polymeric materials composites account for an estimated from 20 to 30% of total volume of solid waste disposed. Thus, there is a tendency to substitute such polymers by those ones that undergo biodegradable processes. Polypropylene (PP) is a commodity, with high melting point, high chemical resistance, low density, with a balance between physical and mechanical properties and easy processing at low cost. Nevertheless, PP shows limitations for some special applications in automotive industry and civil construction. In order to minimize this deficiency, related to rheological behavior of polymer melt, especially referring to viscosity in processing temperature, a 50% mixture with HMSPP (High melt Strength Polypropylene) was used. PP/HMSPP was blended with 10, 15, 30 and 50% of natural (sugarcane bagasse) and synthetic polymers (PHB and PLA) aiming to partially biodegradable materials. The admixtures were subjected to gamma-irradiation at 50, 100, 150 and 200 kGy and then further assessed by mechanical tests in order to evaluate their degradability.

Jan 1, 2015

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Nils Lippmann, Ulrich Weber, Siegfried Schmauder, Jr. Mishnaevsky

"A computational approach to the optimization of fracture resistance of multiphase materials (here - high speed steels) by varying their microstructure is presented. The main points of the optimization of steels are as follows: (1) development and verification of the model: numerical simulation of crack initiation and growth in real microstructures of steels, (2) computational experiment: simulation of crack growth in different idealized quasi-real microstructures and (3) the comparison of fracture resistances of different microstructures and the development of recommendations to the improvement of the fracture toughness of steels. Numerical simulations of crack growth in real microstructures of steels and different idealized carbide distributions are carried out. On the basis of the simulations, recommendations for the improvement of high speed steel microstructures are given. It is shown that the fracture resistance of the steels is much higher for the fine than for the coarse version of the same type of microstructures.IntroductionThe purpose of this work is to develop an approach to the optimal design of multiphase materials on the basis of numerical simulation of their behaviour under mechanical loading. We suggest here the following strategy:1. Collecting input data for the simulations: taking a micrograph of a microstructure, and determining mechanical properties and failure conditions of the material constituents [1, 2],2. Simulation techniques and assumptions are tested for a real microstructure of the material: crack growth in a real microstructure is simulated and then compared with the experimental data,3. Computational experiments: different microstructures of materials are tested in the numerical model under the same loading conditions. The calculated service properties of the different microstructures are compared, and recommendations are developed. As differentiated from the ""real"" experimental techniques, the computational experiment is much cheaper and not labor- and time-consuming."

Jan 1, 2001

By T. Gunawansa, T. L. Alford, Zhao Zhao, A. R. Lanz, N. David Theodore

Many sustainability issues arise during the manufacturing processes that are currently used for solar cells. Solar energy is a renewable energy source that is independent of the earth’s resources, and it is therefore important for the development of more sustainable technologies. Microwave annealing (MW) has been proposed as a technically feasible fabrication scheme for large area silicon solar cells. Apart from that, microwave annealing has been demonstrated to be a promising alternative for repairing damage and electrically activating dopants in ion-implanted semiconductors for integrated circuit manufacturing. A microwave oven is cheaper than conventional furnace systems. In addition, microwave heating is much more efficient than conventional furnace heating, as heating is directly produced inside the material. This minimizes the loss of energy due to heating of the ambient. There is a need for more efficient processing techniques. In this study, microwave annealing is used as an alternative to the current postimplantation processing. Arsenic-doped silicon was microwave annealed (with an aluminacoated silicon carbide susceptor) to activate dopant atoms and to repair damage that was caused by ion implantation. Sheet resistance and Hall effect measurements were used to assess the extent of dopant activation. Rutherford backscattering spectrometry (RBS) with ion channeling was conducted to determine the extent of recrystallization. The dopant activation and recrystallization resulting from microwave annealing is compared with that resulting from conventional rapid thermal annealing (RTA) with the same heating profile. The results show that when compared to RTA, susceptor-assisted microwave annealing results in better dopant activation for shorter anneal times under the same heating conditions.

Jan 1, 2015

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

By Hal dun Kurama

In thus-study, Bigadic upper zone zeolitic tuff, which contains about 87% clinoptilolite was used as an ion exchanger for removal of Pb++, Cu++, Cd++ and Hg++ ions from wastewater. Bench scale experiments with two different glass columns, were carried out continuously under the closed/ open circuit conditions. Before ion exchange tests, zeolite samples were treated with NaCI (6ml/ min. and 42BV). The effects of particle size, bed volume, pH and flow rate on the ion exchange capacity were determined. Under the best operation conditions, the effect of initial influent solution concentration on ion exchange selectivity was tested. As a-result, it was found that the Bigadiç clinoptilolite had the following ion exchange capacities;

Jan 1, 1995

By Thenepalli Thriveni, Ch. Ramakrishna, Yujin Jegal, Ji Whan Ahn, Jyothi Rajesh Kumar

In alumina production or alumina refining, bauxite is converted to alumina (aluminium oxide) The rare-earth elements (REEs) are a group of 17 chemically similar metallic elements (15 lanthanides, including scandium and yttrium). Rare earth elements play a key role in many industrial applications, petroleum refining, clean energy, automobile, electronics, and defense applications. These rare earths are essential to the success of green technologies. China today controls more than 95 percent of the rare-earth supplies and nearly all rare-earth refining and after 2009 year rare earths crisis raises due to China’s export restrictions and growing internal demand for rare earth elements. The extraction of gallium and yttrium from Korean red mud (KC red mud) by selective acid leaching was explored. The recovery of gallium and yttrium from a leach solution of the Korean red mud using solvent extraction was studied. A number of extractants were investigated for the extraction of those mentioned two rare earth elements and also we proposed a flow sheet of rare earth elements respectively. The toxic heavy metals presented in KC red mud were removed by CO2 stabilization.

Jan 1, 2015

By Gaifeng Xue, Xiaohong Xu, Meng Liu, Yijie Song, Guotao Xu, Jixiong Liu

BN (Boron Nitride) based composites were prepared with hot-pressing by using h-BN as main material in ceramic preparation process. The relative density, bending strength, vickers’ hardness, thermal shock resistance, thermal expansion coefficient, thermal conductivity, phase composition and microstructure were tested and analyzed by using modern testing technology. The results indicate that the best formula is B, the relative density is 97%, the bending strength is 260 MPa, the hardness is HV5 343kg/mm2, the thermal expansion coefficient is 2.8×10-6℃-1, the thermal conductivity is 22 W/(m.K) and have no crack after thermal shock for 20 times by water cool. XRD analysis indicates that the main phase compositions are h-BN, β-Si3N4 and sialon. SEM studies show that the grains wrapped up by solid solution.

Jan 1, 2015

By Jeffrey L. Zelms

Environmental issues and how they are addressed -- or not addressed -- by the lead industry in the 1990s will determine the eventual fate of lead mining in both the U.S. and worldwide. Clearly, governmental regulation throughout the West will become harsher. Equally clearly, the industry has? failed to educate the public regarding lead. Instead of public support for a critical mineral, we face widespread public ignorance and paranoia. If we can demonstrate the public interest benefits of the industry, the 1990s will be a decade of continuing growth -- not dynamic growth, certainly, but growth at least comparable to the world economy. If, however, we fail to demonstrate the industry's public interest benefits, the 1990s could mark the beginning of the end of our business.

Jan 1, 1990

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By Fuqiang Zheng, Feng Chen, Wenting Duan, Yufeng Guo, Tao Jiang

High-quality titanium-rich material is of significance in the development of titanium industry as it is the main raw material to produce sponge titanium and titanium white using chloride process. Activation roasting of titanium slag with high Ca and Mg contents as adding H3PO4 followed by acid leaching was investigated to prepare titanium-rich material. The effects of H3PO4 dosage, roasting temperature and time, hydrochloric acid quantity, acid leaching temperature and time on TiO2 grade and removal of impurities were studied. The results show that after the finely ground titanium slag roasted with 8% H3PO4 at 1000 for 2h, most Mg impurities in anosovite solid solution structure were converted into simple acid–soluble compounds. The impurities such as Ca and Mg obviously decreased when the hydrochloric acid concentration was 20%, leaching at 100 °C for 2h, from which a titanium-rich material containing 82.56% TiO2 and 1.15% (CaO+MgO) was obtained.

Jan 1, 2016

By C. L. Lin

Multiphase, irregularly-shaped randomly-oriented PARGEN particles were grown to determine the breakage/liberation characteristics of such locked particles. The simulated locked particles were randomly broken to establish the liberation characteristics of the broken fragments. The progeny size distributions are consistent with Gilvarry's volume and surface flaw model for single particle breakage. The extent of liberation of both continuous and dispersed phases can be described from the conservation of interfacial area. In this regard the data can be normalized and liberation described for a wide range of dispersed phase grades and dispersion densities.

Jan 1, 1988