Search Documents

By A. V. Tarasov

Based on the data available in the literature and the practical experience of new metallurgical plants, a method has been proposed and relevant studies conducted for metallurgical processing of zinc sulfide concentrates. Process conditions and parameters have been identified, which ensure high levels of recovery of zinc into solution. This is achieved by leaching concentrates under the normal pressure at a temperature of >90°C in the presence of ferric iron ions. Sulfide sulfur is converted to elemental sulfur in this process. To produce elemental sulfur it is necessary to maintain oxidizing conditions in the system, characterized by a positive Eh value. In order to eliminate the interfering effect of elemental sulfur formed in the process, it is possible to add surfactants into the concentrate pulp. The proposed technology has certain advantages as compared with the high-temperature pressure leaching and is considered as a basic technology to be applied to increase zinc production at one of the Russian zinc plants.

Jan 1, 2006

By F. Sakurai

The enlarged Mitsubishi process in Naoshima has been in steady operation since. May 1991. However, the sulfuric acid plants have been in operation for more than 30 years. The acid plants were modernized between 1999 and 2001 by renewing some of main equipment such as the drying tower and gas heat exchangers, and introducing new technology. At the same time, as an electric energy saving measure, the electric power consumption in the sulfuric acid plant was vastly improved by decreasing the volume of gas treated the installation of low temperature activity catalyst in the 1st pass of the converter and optimization of main gas blower runner. Furthermore, last year, the oxygen plant was replaced and enlarged, and anode production increased from 240,000 to 280,000 tonnes per year with an associated increase of sulfuric acid from 550,000 to 660,000 tonnes per year. This paper describes these recent improvements in the acid plant at Naoshima smelter.

Jan 1, 2002

By V. M. Paretsky

Most recent developments made in the Gintsvetmet Institute in the field of technologies and equipment for single-stage autogenous smelting of copper sulfide raw materials to produce white metal and blister copper on the basis of oxygen-flame smelting process and separation of highly basic calcium-containing slags have been discussed. This technology includes the oxygen-flame smelting process (KFP Process) to produce highly basic self-disintegrating ferrite-calcium slags with their subsequent flotation to recover copper and a basically new sparging smelting process (FBP Process) to produce combined slags subjected to decopperizing inside the same furnace. Results of special investigations of the slag structure obtained in the KFP and FBP processes and substantiating selection of their chemical and phase composition have been presented. It has been demonstrated that the above processes meet the stringent world-level requirements to advanced technologies with respect to energy conservation and environmental safety with different scales of production and within a wide range of specific conditions of particular operations.

Jan 1, 2006

By W. Persson

The first installation at a copper smelter of a Semtech OPC System for continuous, on-line production control of copper converting in PS converters took place in 1994. At present OPC systems are installed at 19 PS converters. The technology presents to the operator real-time information on the progress of the process he is controlling in the form of optical process parameters, thus facilitating dynamic process control. The optical process parameters are based on time- and wavelength resolved registrations of the light emitted by the off-gas flames and identification of correlation between these parameters and characteristic metallurgical process data. The present paper provides a description of the technology as seen by the furnace operators and a summary of operating experiences made during five years of full-scale, operation at various smelters, reviews influences from the technology on smelter operational practises and comments on recent developments as regards new applications of the technology.

Jan 1, 1999

By Toshihiro Tanaka

The information on viscosity and surface tension of molten slag is indispensable to design new refining procedures in ferrous and non-ferrous processes. For example, the authors have tried to develop "Capillary Refining" to remove impurities in liquid metals by applying capillary absorption of molten slag with those impurities into solid fluxes which have a lot of small capillary tubes. It is necessary to adjust the above physico-chemical properties to adequate conditions on the capillary penetration. In the present paper, we discuss our recent trial to predict surface tension and viscosity of molten slag in multi-component systems. We have derived a thermodynamic model to predict the surface tension of molten slag by using ionic size, molar volume and surface tension of pure components. In addition, we have applied neural network computation to evaluate the viscosity of molten slag. We found good agreement of the calculated results with experimental values of the surface tension as well as the viscosity in various slag systems.

Jan 1, 2006

By Mala Nath, Atjit Mallick, Asheesh Kumar

"The present research work is aimed to focus on the development of chemically stable light weight microporous carbonaceous material, such as activated charcoal incorporated either with titanium n-butoxide, titanium diisopropoxide bis(2,4-pentanedionate), vanadium 2,4-pentane-dionate or zinc 2,4-pentanedionate having varying wt% of the metal (2-8%) using ethanol as solvent at 40--50 oC followed by calcinations at 100, 150 and 200 cC, except the samples with titanium diisopropoxide bis(2,4-pentanedionate) which are calcinated at 80 oC. Atomic absorption studies along with FESEM revealed that the maximum incorporation of metals (Zn, V and Ti) in activated charcoal was observed with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC , 4 wt% of vanadium 2,4-pentanedionate at 100 oC, 2 wt% of titanium n-butoxide at 100 oC and 2 wt% of titanium diisopropoxide bis(2,4-pentanedionate) at 80 oC, and equilibration time of 20-24 h was used in each case. Hydrogen sorption behavior in these carbonaceous materials has also been studied at 77.4 K and low pressure up to I bar. The highest hydrogen uptake obtained was 1.45 wt% (164.5 cm3 (STP)/g at P/Po = 1.0) for activated charcoal incorporated with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC.IntroductionTwo of the major challenges for humanity in the next twenty years are the shrinking availability of fossil fuels, the global warming and potential climate changes that result from their ever-increasing use. So it is necessary to fmd an energy source that is convenient, flexible and controllable. One possible solution to these problems is to use an energy carrier such as hydrogen, and ways to produce and store hydrogen in electric power plants and vehicles. Hydrogen storage is the bottleneck for the breakthrough of hydrogen as energy carrier in automotive applications [1]."

Jan 1, 2012

By Tang Chaobo

Employing manganese carbonate ore and zinc oxide dust as material, Mn-Zn compound oxide powder for soft magnetic ferrite was prepared by a serial methods, as follows: leaching by using sulfuric acid, removing aluminium and silicon by neutralization and flocculation method, using ammonium bicarbonate to co-precipitating Mn and Zn, calcinations and washing to removing impurity content. The optimal technical condition was obtained by experiments. The difficulty of removing impurity such as Si, Al, Ca, Mg, from leaching solution was solved. The impurity content in the production meets with the preparation standard of high quality soft magnetic ferrite. The compound oxide powder obtained in the experiment was made into lower power loss magnetic ferrite, the quality of magnetic ferrite meet the standard of PC40 which was established by TDK corporation.

Jan 1, 2006

By M. Mujahid, A. Maqsood, M. H. Asghar, K Iqbal

"Thin film multilayer anti-reflection coatings (Si02/Si/Si02) having thicknesses 286/571/143nm were deposited by RF magnetron sputtering deposition technique on 0.5mm thick Si(100)-substrates. Post-deposition annealing is also carried out in the temperature range 150-650°C for 4hr at the rate of 10°C /min. Si Optical window was designed at 4.21lm wavelengths and correlated with modeling software. The films are transparent in the 3-51lffi band of the electromagnetic spectrum, firmly adhered to the substrate. The prepared multilayer thin films are characterized optically and structurally using a spectrophotometer, an atomic force microscope, x-ray diffraction and a scanning electron microscope. Optical and structural characterizations show that the %transmittance is between 60% and 75%, no appreciable change in crystal structure and roughness of coatings vary between 9 and 25 nm when annealed in the temperature range of 150-650oC. Local elemental characterization on the surface of the thin film was carried out using energy dispersive spectroscopy. The quantitative result of energy dispersive spectroscopy has also shown that the ratio of Si to 0 on the film is 0.67: 1.IntroductionSi02 thin films have unique properties in the interfaces with Si and most studied materials in the field of microelectronics and optical devices [1]. Multilayer thin films are using nowadays in the design and fabrication of the shrinking systems with a variety of fields such as optoelectronic devices. The physical properties and parameters can be controlled at scales of microns down to nanometers by using RF magnetron sputtering system [2].Silicon and Silicon dioxide are used as coating materials [3]. These thin films are laid on top of each other in SiO2/Si/Si02 order by RF magnetron sputtering on top of a substrate as given in Table 1."

Jan 1, 2012

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By J. P. Downey, L. G. Twidwell

"The high density sludge process (HDS) is a commercially proven acid rock drainage wastewater treatment process that is based on acid neutralization and metal precipitation. Previous studies have established that metal removal efficiencies in precipitation-based wastewater treatment applications can be improved through metal ion adsorption on ferrihydrite and/or aluminummodified ferrihydrite. This study was conducted specifically to determine whether the metals removal efficiencies at an existing industrial facility could be improved by promoting ferrihydrite and/or aluminum-modified ferrihydrite precipitation during the pH adjustment stages of the HDS process. The metal tenors of the treated wastewater samples are compared with those obtained through baseline experiments, which were designed to simulate the conventional HDS operation. The subject metals were: aluminum, arsenic, cadmium, copper, iron, manganese, nickel, and zinc.IntroductionThe HDS process is commercially proven ARD wastewater treatment technology that involves raising the wastewater pH by adding hydrated lime, caustic soda, or another alkaline substance. In addition to neutralizing the acidity, many dissolved metals precipitate as pH is elevated. Waste volume is minimized by capturing and immobilizing the precipitated solids.However, ARD streams characteristically contain multiple dissolved metal species. The response of various metals to pH adjustment in the HDS process is neither uniform nor quantitative, so minor to trace concentrations typically remain in the treated wastewater following solid-liquid separation. The effectiveness and applicability of the process would be improved if a means were found to further reduce the metal concentrations.Previous research and industrial applications have proven that metal ion adsorption on ferrihydrite (FH) and/or aluminum-modified ferrihydrite (AMF) increase metal removal efficiencies. Ferrihydrite and AMF are considered ideal for cation and anion adsorption from an aqueous solution at the appropriate pH [1]. Ferrihydrate adsorption of dissolved heavy metals is widely practiced throughout the world [2, 3]. It is established that FH and AMF effectively adsorb As contained in aqueous solutions [4]. Arsenic removal by adsorption on FH is the U.S. Environmental Protection Agency’s (EPA) Best Demonstrated Available Technology [5]. Twidwell and Leonhard also demonstrated that heavy metals (Cd, Cu, Ni, and Zn) are effectively removed from solution by coprecipitation/adsorption using AMF and FH [6]."

Jan 1, 2008

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002

By Julian Szekely

A review is given of the current metals processing operations, where electromagnetic forces play an important part in affecting the performance of the system. These include arc furnaces, plasmas, the Hall Cell, electromagnetic stirring and others. These considerations will be extended to discuss what new frontiers may be breached by the intelligent application of electromagnetic phenomena. The topics discussed will include magnetic flow control, levitation melting and cold crucible melting and refining.

Jan 1, 1988

By Jouko Kallionen

Advanced Flotation Technology is the application driven design of flotation cells to achieve the optimum performance for each type and grind of flotation. This can be applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Standard, engineered, components are matched to provide mechanism design and cell dimensions for each case according to feed parameters and flotation type. Advances in process control have been achieved with high level controls and operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed. Excellent results of this Advanced Flotation Technology in large scale porphyric copper ore have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified.

Jan 1, 1999

By Laurentiu Nastac

"Two advanced control solidification technologies were studied in this article to improve the quality of the cast ingots as well as to control the solidification structure evolution during the plasma arc melting (PAM) processing of Ti-6-4 ingots: (i) electromagnetic stirring (EMS), and (ii) ultrasonic treatment (UST). The developed EMS modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure. The UST analysis tool is capable to model acoustic streaming and cavitation. It is used in this work to study ingot solidification under the presence of ultrasound. Predictions of the macrostructure, GET formation and primary dendrite arm spacing for PAM Ti-6-4 ingots processed with and without EMS or UST were discussed.1. IntroductionTitanium (Ti) alloys are melted, refined and cast into ingots through plasma arc cold hearth melting (PAM), electron beam cold hearth melting (EBM) and vacuum arc remelting (VAR) for jet engine applications. Process modeling has become a viable tool to optimize the PAM, EBM, and VAR processes. A comprehensive modeling approach to simulate ingot solidification phenomena in primary melting and secondary remelting processes of Ti alloys would include models for macroscopic mass transfer, heat transfer, fluid flow, acoustic, electromagnetic and species transport. The approach should also include microscopic models to predict the evolution of grain structure in solidifying ingots in conjunction with electromagnetic stirring (EMS) and ultrasonic stirring (UST)."

Jan 1, 2012

By Pertti Pekkala

Outokumpu has 25 years of experience in the SX area. The development of the solvent extraction plants responds to an ever increasing demand for lower operational costs wd for adaptability to process disturbances with minimized risks. In this paper the features of the VSF ("Vertical Smooth Flow") SX technology are described, such as the separated pumping and mixing, the homogenous gentle mixing, the droplet coalescence and the ultra pure settling. A major advantage of the mixing technology is the high stage efficiency of above 99 per cent. The connection between this and some features of the settler front section is clarified. The present design of VSF plants is based on experience of existing operations at, for example, Zaldivar, Radomiro, Morenci, Kokkola and Harjavalta. These production plants cover a unit capacity range of 60 to 3,600 m3/h expressed as a total flow. It is evident that there are no restrictive factors to increase the total flow up to 5,000-6,000 m3/h by introducing the VSF technology. The copper SX technology has a long history reflecting many individual features of the separate copper SX plants. Still it is necessary to verify all actual running parameters by pilot tests taking into account impurities, chemicals used etc. The design of SX plants is not only about the delivery of equipment but also a process concept, and it is best tailor-made and adapted to specific local requirements.

Jan 1, 1999

By Zhang Hengzhong

Ni-P-Fe slag is the by-product in the production of phosphate fertilizer in blast furnace with nickel contained serpentine ore as the raw material. It contains nearly 5-7% Ni, 65-7( Fe, and 10-12% P. The slag is very hard to process, it neither dissolves in aqueous ammonia, nor in sulphate acid. In the stiff the technique to treat the slag in order to extract valuable nickel was developed, it essentially consisted of the processes of roasting, leaching, separation and purification. Nickel sulphate was prepared with this method.

Jan 1, 1993

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Yutaka Saito

"Effect of moisture content must be fully understood for controlling the granule compaction of ceramics. It changes the mechanical behavior of spray-dried granules applied for compaction process, and governs the structure and properties of .ceramics. To understand the time-dependent change in processing, the kinetics was examined for change of moisture content for granules placed in a die and the pressed compacts also. The results were explained in terms of apparent moisture diffusion coefficients. They varied non-linearly with the PVA content in the granules. The results were explained through the non-uniform PVA distribution in the granules.IntroductionMoisture must be controlled in compaction process to produce the green compacts having uniform structure. It affects glass transition temperature of binder and thus the deformation behavior of powder granules under an applied stress. Several studies [1-7] have clarified the effect of moisture content on the compaction behavior of granules and the structure of resultant compacts for both die pressing and cold isostatic pressing (CIP) of pre-formed compacts. In these studies, the moisture contents in the system were equilibrated with the humidity in the atmosphere before compaction. In practice, however, the moisture content in the system may vary with time if the relative humidity of surrounding atmosphere is different from what the granules were equilibrated previously. This is very likely case in real production processes. However, the kinetics of moisture change in the granules as well as in the pre-formed powder compacts have not been well studied. For controlling the microstructure in a system, it is necessary to fully understand the kinetics of moisture change and its relevance to packing structure of powders."

Jan 1, 2000