Search Documents

By James R. Myers

A source of clean gas containing sulfur dioxide and sufficient oxygen for conversion to sulfur trioxide is essential to the production of sulfuric acid. SO2 containing gases obtained from roasting sulfide ores are heavily contaminated with inorganic dust and volatile impurities. If not removed, these contaminants will reduce product acid quality, foul the catalyst beds and mist eliminators, and accelerate equipment corrosion. This paper reviews conventional gas cleaning systems for metallurgical acid plants, followed by a discussion of modern systems utilizing DynaWave Scrubber technology. This technology is based on a unique approach togas scrubbing that can concurrently accomplish several gas cleaning/processing tasks. Scrubbing liquid is injected into the gas stream to create a "Froth Zone". This is a region of extreme turbulence, with a very high rate of liquid surface renewal. It efficiently removes both particulate matter and gas contaminants, and is also a cost effective quenching device for gases as hot as 1250 o C.

Jan 1, 1992

By Hector Carreon

During fretting, high points or asperities of the mating surfaces adhere to each other and small particles are pulled out, leaving minute, shallow pits and powdery debris. Sometimes these surface conditions are neglected, but they are important in some application such as the aerospace industry. In this research work, non-contacting and contacting thermoelectric power techniques are performed in fretted 7075-T6 and Ti-6Al-4V samples. It has been found that the contacting and non-contacting thermoelectric power measurements are associated directly with the subtle material variations such as work hardening and residual stresses due to plastic deformation produced in the fretting zone but surface topography. Therefore, both techniques could be used for a global characterization of the most relevant fretting induced effects. Potential of these techniques to monitor subsurface changes in other severe surface plastic deformation processes are clearly envisaged.

Jan 1, 2015

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By P. R. Taylor

Diamond films have been successfully formed in an inductively coupled plasma (ICP) chemical vapor deposition (CVD) system from several gas mixtures: CH,-H,, C2112-112, and C2112-112-02' Our previous thermodynamic study indicated that the substrate temperature could be lowered by the presence of oxygen species at moderate system pressures (0.3-0.5 atm) and that higher volumetric growth rates required a high temperature source and a moderate pressure system in CVD processing. The principal experimental results were consistent with the thermodynamic predictions. The deposited films were characterized by laser Raman spectroscopy, scanning electron microscopy, and X-ray diffraction. The films were well faceted and uniform, with the growth rates over 10 pm/hr on molybdenum substrates. The crystal size ranged between 1 and 2 microns for a two hour experiment. It was possible to decrease the substrate temperature to below 800 °C in this system.

Jan 1, 1995

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By Jeong-Hwan Kim

The liquid-liquid reactive process (solution process) is often adopted as a synthetic method for precipitated calcium carbonate (PCC) in laboratory studies for its simplicity in operation or ease in controlling process variables. Still, PCC are produced commercially by passing carbon dioxide through a milk of lime, i.e., by a gas-liquid reacting method (carbonation process). Few studies on the carbonation process have been conducted, since the process variables are interrelated and difficult to control compared to the solution process. In this study, both carbonation and solution processes were employed to study the polymorphs of calcium carbonate and growth rate of PCC crystals. The effects of the characteristics of limestone ores as a raw material in the synthetic system of PCC on the synthetic characteristics of PCC were also investigated. To control the nucleation rate in the synthetic systems, the shape factor was considered most important. Single-phase aragonite PCC could be synthesized under a variety of controlled experimental conditions such as ionic strength, solution composition, concentrations of additive ions, and temperature.

Jan 1, 2006

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO'TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By Vaughan R. Voller

In many high temperature processes involving liquid melts the common practice is to solidify a fraction of the melt adjacent to the containment wall; a practice that can provide protection of the structural components of the process. The position, shape and transient behavior of these so called "skulls" and/or "ledges" are directly dependent on the thermal process conditions. This paper presents a model of a generic ledge process that can predict the steady shape of a ledge. Two numerical implementations are presented and compared: (1) based on a space grid of continuously deforming finite elements (2) based on a conjugate grid of fixed control volumes and deforming boundary elements.

Jan 1, 1996

By Yonghua Li, Fanling Meng, Weitao Zheng, Xiaodong Wang

The NiTi thin films were deposited onto copper substrates by magnetron sputtering. Tensile tests were carried out on CSS-44100 electron universal test-machine. X-ray diffraction profile Fourier analysis method has been used to study the mechanical properties of deformation NiTi thin films. The surface micrographs of the NiTi thin film were obtained using scanning electron microscopy (SEM). It has been found that the dislocation density and the deformation storage energy density increased with elongation increased. Microhardness was calculated from the dislocation data. The results showed that the microhardness values were not in a good agreement between calculated values and measured values. The oxide layer on the surface of NiTi thin film affects the measured values of microhardness. The Vickers hardness measured values are larger than the calculated values. The experimental results showed that a series of parallel cracks grew in a concerted fashion across the thin film and the cracks were equally spaced.

Jan 1, 2015

By June-Yong Eom, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

The nitrogen solubility in liquid Mn-Si, Mn-Si-Fe, Mn-Si-C and Mn-Si-Fe-C alloys has been measured by the gas-liquid metal equilibration technique in the temperature range of 1673-1773 K. The additions of silicon, iron and carbon significantly decreased the nitrogen solubility in liquid manganese alloys. The experimental results were thermodynamically analyzed by the Wagner’s formalism to determine the first- and second-order interaction parameters of silicon, iron and carbon on nitrogen in liquid manganese. The thermodynamic parameters can be used to predict the nitrogen solubility in ferromanganese and silicomanganese alloy melts as functions of the melt composition and temperature at given nitrogen partial pressures.

Jan 1, 2014

By Shulan Wang, Xuan Liu, Li Li

"Electrochemistry of Fe(III) in 69CaCl2-12CaF2-19KF and 81CaCl2-19KF (mole percentage, %) was investigated at 827 oC on molybdenum electrode by cyclic voltammetry, chronoamperometry and galvanostatic electrolysis using Fe2O3 as the Fe(III) source. The reduction of Fe(III) to Fe was conducted in one step and controlled by diffusion process. Fe(III) shown greater reduction rate and diffusion coefficient in molten 81CaCl2-19KF than in 69CaCl2- 12CaF2-19KF. Galvanostic electrolysis of Fe was performed in both molten salts with a cylindrical cathode rotating at 200 r/min and dendritic iron deposit was obtained.Keywords: iron; electrolysis; electrochemistry; molten saltIntroductionThe production of iron and steel causes huge emissions of CO2. Iron electrowinning in molten salts with dissolved Fe2O3 using an inert oxygen evolving anode is an alternative process to reduce or eliminate the formation of CO2. Research on novel process of producing metal has been reported recently [1-2] by using CaCl2 as the main electrolyte and dissolving CaO in CaCl2 due to the high solubility of CaO in the melt. This process has been used in preparing many active metals and alloys [3-14]. In the present work, the electrochemical behavior of iron in CaCl2-KF was studied and transport property of iron ion in the melt was discussed.ExperimentalCaCl2,CaF2 and KF (in analytical purity) were dried in air for 48 h. Mixed salts used in experiments were placed in a graphite crucible (??58 mm inner diameter). The graphite crucible together with the salts was heated at 473 K for 12 h in a furnace with flowing Ar (99.99%) before further heating. Temperature inside the furnace was measured by an S type thermocouple. Electrochemical measurements, such as cyclic voltammetry and chronocoulometry, were performed in a three electrode cell by EG&G PAR273A potentiostat/galvanostatand. Galvanostatic electrodepositon of iron was conducted in a two electrode cell. Molybdenum (??2 mm) and iron (??5 mm) were used as the working electrode (WE) and the reference electrode, respectively. A graphite crucible and a magnetite rod (??25 mm ) consisted of 100% magnetite and sintered at 950 oC in argon atmosphere for 2 h with electrical conductivity of 366 O-1m-1 at room temperature were used as the counter electrodes in the galvanostatic electrolysis experiment. Carbon (??10 mm) was used as the counter electrode in electrochemical measurement. The deposits were washed in distilled water bubbled with argon and dried in air before being characterized by X-ray diffraction (PW3040/60 diffractometer) and scanning electron microscope (SEM, SSX-550)."

Jan 1, 2014

By R. W. Smith

The flotation response and electrokinetic behavior of Chlorella vulgaris and Chlamydomonas sp . when using dodecylamine hydrochloride as collector were studied in the absence and presence of Pb(I1). Also, an electron microscopy study was made of the algae after Pb accumulation. The flotation behavior of the organisms after Pb accumulation appears at least partially related to the location of the abstracted Pb onto or into the organisms.

Jan 1, 1991

By Corby G. Anderson

Laboratory testing, interpretation and application of metallurgical technologies can be tedious, time consuming and costly. This paper outlines the use of proven statistical design of experimentation software for rapid optimization of laboratory testing and operating plants with limited representative sample utilization. This results in less costly required testing, a more thorough understanding of results and the ability to simultaneously optimize several variables and outcomes at once. At the Center for Advanced Mineral and Metallurgical Processing, this testing methodology has been used successfully in many metallurgical development and plant optimization projects thereby confirming its real world utility and application. Accordingly, several applied examples in flotation and hydrometallurgy will be outlined in this paper. This will include flotation testing of a copper gold ore, flotation testing of a copper, cobalt and gold ore, optimization of an industrial hydrometallurgical jarosite circuit and optimization of industrial nitrogen species catalyzed pressure leaching of a copper enargite concentrate.

Jan 1, 2006

By C. D. Seybert, J. W. Evans

"The elimination of convection is essential in experimental investigations of diffusive transport (of heat and matter) during solidification. This paper describes an investigation of an approach whereby a magnetic field gradient is applied to a electrically non-conducting diamagnetic liquid. A magnetic body force then arises which is dependent on the volume susceptibility of the liquid and thereby on the density. With the field gradient aligned vertically and of correct magnitude, the variation of gravitational body forces due to density variations (arising from temperature variations, for example) can be counterbalanced by a variation in magnetic body force.Preparatory to a study of convection control in diamagnetic liquids, PN measurements have been made of the convection occurring during the solidification of water. A peculiar flow arises because of the density maximum at 4°C. Modeling of the flow the steady-state solidification of water in an extremely high field magnet at the NHMFL indicates that flow can be significantly reduced, but it is suggested that, due to field gradient variations within the cell, flow cannot be completely halted. INTRODUCTIONNatural convection is inherently a part of terrestrial solidification. Density-based convection during solidification, due to gradients of temperature and/or concentration, has a significant effect on a material's properties. The design of products with specific material characteristics has required the development of many processes to control convection (such as in the growth of semiconductor crystals, and electromagnetic stirring in steel casting). The expansion of fundamental knowledge about the process of solidification requires collecting data in the absence of density-based convection, while most of science's solidification data (and thus the equations that science has fitted to those data) have been obtained under the influence of gravity. Only relatively recently, through clever experimental design (e.g., drop towers, high altitude parabolic flights, and space laboratories), have investigators been able to study solidification in an environment with ""micro-gravity""."

Jan 1, 2001

By Doug Halbe

?Many are called, but few are chosen.? The biblical adage applies not only to life, but also to hydrometallurgical processes. There have been, in the past, many outstanding successes with new processes ? and also some dismal failures. What are the odds of success for a new process? When there have been problems, why? What can you do to make sure these problems don?t occur with your process? What effect will a slow startup have on project economics? How do financial institutions ? the people who loan your company money for the project ? feel about new processes and why? Is it possible to predict or estimate the time required to reach design parameters?and if so, how do you sell this estimate to management ? and financial institutions? Probably most important ? when do you start thinking about the answers to these questions?

Jan 1, 2003

By Leonid M. Lerner

High temperature aluminum Alloy 8009 is a rapidly solidified/powder metallurgy aluminum-iron-vanadium-silicon alloy. This alloy in combination with hard oxide aluminum film has unique engineering properties which may recommend its use in compressors and impellers for aerospace applications. Various anodizing processes (including Sanford Low Voltage DC+AC Process) for these task will be evaluated and normal chemical composition, physical properties, and macrostructures of 8XXX aluminum alloys will be presented.

Jan 1, 2006

By Y. Iguchi, T. Narushima, T. Shiozawa, M. Maruyama, R. Arashi

"In situ observation system for thermal oxidation using Raman spectroscopy' was constructed, and oxide films formed on liquid pure Al and Al-Mg alloys (Mg contents = 1 and 4 mass%) were analyzed at room temperature to 1273 K in dry oxygen. In situ Raman spectra of the surface of a liquid Al-:-4mass%Mg indicated the formation of MgO • AlP3 (spinel) as oxidation products, while a -AlP3 and MgO • Alz03 (spinel) were observed on a liquid Al-1mass%Mg alloy. It was suggested that the formation of MgO film affected oxidation behavior of these alloys.IntroductionLiquid aluminum alloys are cast to ingots mainly by the continuous casting process. It is well-.known that surface cracks could be caused by oxide films formed on the surface of melt during continuous casting and defects due to the film. With regard to oxidation behavior of liquid aluminum alloys, many investigations l -s have been carried out from the view point of formation of ceramic metal composites(CMC) which are expected as cutting tools and structural materials 1.2. It is very important for reasonable continuous casting and CMC formation processes to elucidate oxidation behavior of melts.Oxidation behavior of materials generally depends on compositions and properties of oxide films formed on the surface. If in situ observations of oxide films are available during oxidation, evaluation of oxide films and interpretation of oxidation mechanism could be expected. Laser Raman spectroscopy is one of the most appropriate techniques for in situ observation of oxide films under various atmosphere at high temperatures. The authors have discussed the effects of atmospheres and sample compositions on oxide film formation mechanism on Fe-Si alloy6 and SiC-B4C composite7 on basis of an in situ observation by Raman spectroscopy. In spite of many previous studies, systematic and clear explanations have never been gotten on oxidation behavior of liquid aluminum alloys. And no in situ observation has been made except for transmission electron microscopy(TEM) and X-ray diffraction(XRD)."

Jan 1, 1996

By Noritaka Horii, Katsuyoshi Kakinuma, Hiroshi Yamamura

"ZrO2 and Y2O 3-doped ZrO2 gel film were obtained by spin coating of sol from Zr-n-propoxide, n-propanol, acetylacetone, nitric acid, and water on a silica glass as a substrate. ·Dried gel films crystallized to monoclinic, tetragonal, cubic and their mixed phases, depending on the chemical composition of sol, .firing temperature, and coating cycles. ZrO2 films with highly preferential orientation were successfully obtained from a solution containing a large amount of n-propanol. The highly oriented ZrO2 film was found to have high transparency compared with non-oriented 'films. Electrical conductivity of 8 mol% Y2O 3 doped ZrO2 film was also measured.Introduction3 mol% Y2O 3 doped ZrO2, which has a tetragonal symmetry is ·well known to have a strong mechanical property and a high toughness. (1) On the other hand, 8 mol % Y 2O 3-doped ZrO2 is high oxide-ion conducting material and is applied to oxygen sensor, oxygen pump, and solid oxide fuel cell (SOFC). (2) Sol-gel methods using metallic alkoxide are widely applied for synthesizing ceramics such as high-purity fine particles, thin film, and fiber. (3) For ceramics films, many reports have been made on SiO2, (4) TiO2, (5) and PZT. (6) Several case studies have been done on zirconia film based on the sol-gel method, (7) - (11) but very few on preferentially oriented film and on systematic Y zO3 doping. Almost zirconia ceramic· films reported were prepared by means of dip-coating. Kamiya et al. (12) and Ganguli et al (13) converted zirconia into fiber. Sol from Zr alkoxide is usually very unstable, and a stabilizing agent such as glycol or ß-keton is used beforehand (7) (14)."

Jan 1, 2000

By Itavahn Alves da Silva, Jose Dimas de Arruda, Amanda Aparecida Fátima Arruda, da Silva de Souza, Carlos Antonio da Silva, Varadarajan Seshadri, Samuel

The knowledge of the flow field inside a continuous casting mold is essential to improve operational efficiency of the process and also to achieve better inclusion control. Physical modeling, PIV technique and CFD have been employed to assess the velocity distribution in the metal- slag interface region in a slab mold. The analysis of results shows how higher casting velocity and lower immersion depth of submerged nozzle can lead to higher turbulence in the slag-metal interface. The effects of density difference between slag and metal and interfacial tension between the phases have been highlighted.

Jan 1, 2016

By Yue Tian, Shengqian Wang, Lifeng Zhang

This paper is to discuss the removal of non-metallic inclusions from molten steel using a high frequency magnetic field. In experiments, a certain amount of aluminum was added to the molten steel in a crucible to generate aluminum inclusions. A layer of aluminum clusters were observed close to the wall of the crucible after the electromagnetic (EM) field was imposed. Three dimensional EM field and fluid flow simulation were performed and showed that over 91% inclusions transported to the skin depth (2.31 mm) of the molten steel. The calculation of inclusion removal agreed well with the experimental observation. The separation mechanisms of inclusions from the molten steel by the high frequency EM field were discussed.

Jan 1, 2014