Search Documents

By Jiao Li, WenhuiMa, KuixianWei, YongnianDai, Cong Zhang

The paper studied the diffusion process of nitrogen and characteristic distribution of iron impurities in the bottom of cast crystalline silicon ingot along the direction of crystal growth. According to the dynamics analysis of the decomposition of Si3N4 coating, the diffusion process of nitrogen into multicrystalline silicon ingot during casting process should be divided into three steps. The diffusion length of nitrogen in multicrystalline silicon ingot is 700 μm. The results of EDS analysis indicate that the distribution characteristic of iron in multicrystalline silicon ingot is concerned with the diffusion process of nitrogen in this length. Based on the above research results, the distribution model of iron in casting multicrystalline silicon ingot was established and verified by the experimental results.

Jan 1, 2015

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By Melvin H. Miles

"Considerable research has been conducted on the anodic oxidation of methanol in fuel cells. The electrochemical reduction of carbon dioxide in aqueous solutions to form methanol is the same reaction in reverse, i.e. CO2 + 6 H+ + 6 e- ? CH3OH + H2O. The same catalysts and conditions may operate for both reaction directions. This carbon dioxide reduction reaction, however, must be able to compete with the electrochemical reduction of water to form hydrogen gas. Thermodynamically, the reduction of CO2 to form CH3OH is slightly more favorable than the reduction of water. The use of nearly neutral electrolytes rather than acidic electrolytes makes the reduction of CO2 kinetically more favorable. The thermodynamics of various reaction steps are presented. Similarities exist with the electrochemical reduction of CO2 and the green-plant photosynthesis process that converts CO2 to carbohydrates.IntroductionVirtually all of the oxygen in the earth’s atmosphere is of biological origin having been generated by green-plant photosynthesis from water and carbon dioxide [1]. The net reaction can be represented byCO2 + H2O ? O2 + [CH2O] (carbohydrates, etc.) (1)Chlorophyll and enzymes promote this reaction, and the energy required comes from sunlight. The actual photosynthesis process is a complex multistage reaction and requires 469 kJ mol-1 of energy supplied by the sun. Isotope tracer experiments using 18O have shown that both the oxygen atoms in the O2 molecule originate from H2O, whereas oxygen atoms in the carbohydrates come from CO2 [1]. The total amount of water on the earth is split by photosynthesis and reconstituted by respiration and combustion once every 2 million years or so. The photosynthetically generated oxygen gas temporarily enters the atmosphere and is recycled about once every 2000 years [1]. The carbon dioxide is partly recycled in the atmosphere and oceans after an average residence time of 300 years and is partly fixed by precipitation of CaCO3 and other carbonate minerals [1]."

Jan 1, 2008

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993

By Martin B. Schranz

Copper sulfate pentahydrate is recovered from the spent etchant waste stream of a printed circuit board manufacturing facility by cooling crystallization. The fluidized bed crystallizer contains submerged cooling surfaces which are bathed in a stream of air. The air bubbles provide agitation which improve heat transfer, reduce fouling and maintain crystals in suspension. The recently patented apparatus (US 5,523,064) has advantages when compared to a conventional surface cooled crystallizer including capital cost, ease of operation and production of larger more uniform crystals

Jan 1, 1997

By N. Moelans

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NiINiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at 1100 and 1200°C and pO2 values between 10-3 and 10.12 bar were obtained. The measurements were evaluated with? thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Moelans. N.

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NilNiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at I 100 and 1200 °C and pO2values between 10-3 and 10-12 bar were obtained. The measurements were evaluated with thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By M. Sizgoric

Certain types of mineralogical alteration due either to weathering or serpentinization, and the effects these transformations have on the flotation of nickel sulfide ores are discussed. These effects are generally deleterious due to: (a) the poor flotation properties of the alteration minerals (as in the case of tochilinite), (b) the nature of the alteration texture (as in the case of violarite), or (c) .close association of the alteration products with other undesirable minerals (such as nickeliferous smythite). Several examples from INCO Metals Company's mines and mineral prospects are given as illustration.

Jan 1, 1981

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

Pyrometallurgical reactors constitute a key processing component in the total primary and secondary resource cycle, being involved both in primary smelting, converting and extraction, as well as the reprocessing of scrap, from aluminum cans to end-of-life automobiles. To effectively control the overall resource cycle, one needs to take a systems modeling approach of the whole cycle, seeking to also understand the dynamic process behavior of the individual components of the cycle, and then especially the part that contributes most to the chemical conversion, namely the pyrometallurgical reactor. This paper highlights the role of pyrometallurgical thermodynamics, in the whole resource cycle and specifically places equilibrium thermochemistry in the context of process dynamics where large variable inventories are recycled or maintained within the system. This paper will therefore review the semi-empirical dynamic modeling tools, which are used to model complex systems with the specific goal of developing dynamic predictive models, which also include slag-alloy chemistry, towards controlling the recycling in a feed forward manner. To illustrate the primary processing side, high carbon ferrochrome will be presented as a brief case study. It also will show how the distributed nature of the chemistry of melts in the case of primary extraction, and secondary materials such as recycled end-of-Iife vehicles, have a significant impact on the process outcomes and model predictions. It is therefore argued that the fundamental thermodynamics and kinetics in metallurgical reactors playa final crucial role in modeling the closed material cycle, but only when it is used in conjunction with process systems theory based on reconciled data for parameter estimation and model calibration.

Jan 1, 2003

Pyrometallmurgical reactors constitute a key processing component in the total primary and secondary resource cycle, being involved both in primary smelting, converting and extraction, as well as the reprocessing of scrap, from aluminum cans to end-of-life automobiles. To effectively control the overall resource cycle, one needs to take a systems modeling approach of the whole cycle, seeking to also understand the dynamic process behavior of the individual components of the cycle, and then especially the part that contributes most to the chemical conversion, namely the pyrometallurgical reactor. This paper highlights the role of pyrometallurgical thermodynamics, in the whole resource cycle and specifically places equilibrium thermochemistry in the context of process dynamics where large variable inventories are recycled or maintained within the system. This paper will therefore review the semi-empirical dynamic modeling tools, which are used to model complex systems with the specific goal of developing dynamic predictive models, which also include slag-alloy chemistry, towards controlling the recycling in a feed forward manner. To illustrate the primary processing side, high carbon ferrochrome will be presented as a brief case study. It also will show how the distributed nature of the chemistry of melts in the case of primary extraction, and secondary materials such as recycled end-of-life vehicles, have a significant impact on the process outcomes and model predictions. It is therefore argued that the fundamental thermodynamics and kinetics in metallurgical reactors playa final crucial role in modeling the closed material cycle, but only when it is used in conjunction with process systems theory based on reconciled data for parameter estimation and model calibration.

Jan 1, 2003

By Manuela Castaneda, Henry A. Colorado

This paper is about the use and stabilization of iron oxide based powders with arsenic contents coming from the purification of water. Cement paste samples with 0.0, 2.5, 10 and 20wt% of waste were fabricated by mixing mechanically all components. There are two main positive impacts of using this waste, first, this waste is produced in large amounts worldwide, and therefore the stabilization has a significant impact for the environment. Second, the waste can be used as an admixture and filler for cement, and therefore reduce the amount of cement in the concrete, which has a major impact in the CO2 footprint since cement industry produces a lot of this gas. Compressive strength and density tests were tested after 28 days. Microstructure was analyzed with scanning electron microscopy and x-ray diffraction. Results show that compressive strengths greater than 20 MPa were obtained and the samples had calcite, portlandite and ettringite phases.

Mar 1, 2018

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By Chao Zhang, Jian Guo, Chaoquan Yao, Leige Xia, Xinyu Li, Jianliang Zhang

In this research, analytical reagents were used for the sintering experiments. And the sinters were using X-ray diffraction, scanning electron microscope and mineralogical microscope analysis to study the effect mechanism of manganese on the silico-ferrite of calcium and aluminum (SFCA) bonding phase formation during the sintering process. The results indicated that the increasing content of manganese would greatly reduce the content of SFCA, and promote the formation of calcium aluminum silicate and the amount of pores and cracks. The existence of manganese inhibited the silicon form into the SFCA and a great deal of Fe2O3 was participated in the crystal transition to Fe3O4. When the ratio of the added manganese was less than 3% in the mixing, the calcium ferrite was in substantially interleaving corrosion with hematite and magnetite. Both the porosity and silicate glass phase content were low simultaneously, which contributed to the sintering production.

Jan 1, 2015

By Anil Saigal, Jr. Fuller, Said Jahanmir

"All-ceramic crowns, including glass-infiltrated spinel composites, are coming into widespread use because of their superior aesthetics and chemical inertness. This study investigates the residual stresses that are developed in these composites as a result of cool down from the glass-infiltration temperature to room temperature due to slight mismatch in the coefficients of thermal expansion and its effect on the mechanical behavior of these composites. Two-dimensional finite element simulations were performed using an object oriented finite element program OOF. The OOF program is a combination of two programs. The first program, PPM200F, is designed to read an image file such as a micrograph. The individual pixels that constitute the micrograph may be collected into groups and their material properties assigned. PPM200F is then used to create the finite element model/mesh that OOF then reads. The average residual stresses are found to be tensile in the spinel matrix and compressive in the infiltrated-glass. There is large variation in residual stresses and strains from location to location with presence of locations at which the glass is under tensile stress. The crack initiation and initial propagation in glass-spinel composites is at the glass-spinel interface in both the glass and the spinel. The presence of residual stresses can lead to lower crack initiation stresses and degrade the mechanical properties of the composites.IntroductionGlass-infiltrated spinel ceramics are in clinical use as core materials in all-ceramic crowns and as inlays and onlays (1-3). Advantages of ceramic composites include near net-shape forming with high strength in the infiltrated state. Besides, spinel is quite translucent and may potentially be used without a veneer. However, these ceramic composites are subject to damage accumulation from repeat oral contact loading and often fail after a few years of use (4). This paper examines the residual stresses that are developed in these composites, after cooldown from the glass infiltration temperature to room temperature, due to the slight mismatch in the coefficients of the thermal expansion of the two phases."

Jan 1, 2001

By Luis W. Pommier

The wastes of the plating industry are generated in the process of rinsing the plated objects and during the cleaning of the plating shops. High volumes of hazardous waters are neutralized on site producing recyclable water, generating a metal rich, hazardous, filter cake. Occasionally, a complete plating bath has to be discarded which increases the metal content of the filter cakes. These filter cakes are discarded as hazardous at a cost of over $ 250 per ton. The metals found in the cakes are generally copper, nickel and chromium or zinc, lead and cadmium, assaying from 2% to 15% or even higher content of each metal The metals and their contents are highly variable. Some plating shops discard their products directly to hazardous waste sites, others, have them collected by companies which consolidate wastes from several producers prior to discarding. These wastes, richer in metal content than mine ores, need neither mining nor crushing and grinding for concentration. The commonly found impurities in the mine ores, i.e.: pyrites, arsenic, and valuable metals which are present in minute quantities, are absent in the filter cakes. The processes available to selectively recover the metals from the filter cakes, are discussed based on their technical and economic merits. The flow-sheets include leaching, solvent extraction when required, and electrolytic refining. Examples, showing the separation of copper, nickel and chromium and also of zinc and lead in pilot plants, show the technical and economic viability of the processes.

Jan 1, 1996

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b )process chemistry c)discharge options and recovery of treated water and d) sludge disposal The long term goal of any smelter and/lor refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003