Search Documents

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI's threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

By D. J. Reddish

This paper illustrates how numerical modelling has been utilised to predict water and gas pathways around active longwall panels using two case studies. This information has proved invaluable m the design of methane drainage schemes and for risk assessments undertaken at the mining planning stage. The modelling approach described has now been applied successfully to several situations in UK coalmines in order to optimise the position, length and orientation of methane drainage boreholes. The first case study describes the numerical modelling of the stress and shear plane development mund a longwall panel. The simulation was used to predict potential gas pathways through regions of low stress confinrment which are conducive to fluid flow. The conclusions from the modelling were utilised to allow an increase in the volumes of gas drainage and allow the efficient mining of the panel. A detailed discussion is provided on the model construction, determination of input paramters and optimisation of the borehole positions Details are provided on how the models allow a prediction of the fracture patterns, stress distributions and zones of reduced permeability around an active longwall panel. The second case study describes the numerical modelling of a fault adjacent to a face line drivage of a panel that had just started to be retreated. An inrush of water had occurred and a concern was whether further mining would lead to more extensive inrushes or whether the water inrush was associated with more local, limited capacity water bearing features. The role of a fault that was positioned close to the locality of the mine workings was examined. Fracture patterns stresses, strata permeability and water flows were predicted using mechanical and hydro-mechanical coupled models.

Jan 1, 2003

By Bruce Hebblewhite

An ACARP-funded industry research project in Australia recently investigated the problem of premature rock bolt failures in underground coal mines. The project carried out limited sampling from 9 different collieries in NSW and Queensland, followed by a more comprehensive, controlled sampling from one colliery. Over 50 broken bolts were collected and subjected to metallurgical analysis at UNSW to determine both the steel composition and to analyse the fracture surfaces. Prior to this study, there had been anecdotal evidence of similar bolt failures from a number of sites within the industry. The sampling and analysis conducted by this project - whilst being below a statistically representative sample of the entire industry bolt population - highlighted the fact that bolt failures were continuing to occur at a number of sites, in both older and recently installed bolts. The failures were almost entirely attributable to stress corrosion cracking (SCC). It appears that a combination of factors - including steel composition, bolt manufacturing process, loading environment, geological and hydrological environment, bacterial corrosion - can all contribute to this problem. There is no simple solution, however, as with similar research findings from the UK, it appears that steels with higher values of fracture toughness, or Charpy Index, are less susceptible to SCC. Testing to date has been limited to bolt failures below the resin encapsulation horizon. A real concern is the potential extent of the problem at higher horizons, within the encapsulation. These may require some form of non-destructive testing (NDT) for detection. Initial trials in Australia of the ultrasonic device developed by DMT in Germany have proved encouraging. Further testing using this device is anticipated in future research. This paper describes the outcomes of the project, completed in 2002.

Jan 1, 2003

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By Al Campoli

One of the critical variables affecting resin bolt performance is the size of the resin annulus, defined as the difference between the hole and bolt radius. The vast majority of the millions of resin roof bolts installed each year in the United States employ an annulus between 0.125 and 0.188 inch. As the annulus size decreases the resin flow around the bolt becomes more difficult, increasing the resin pressure induced by bolt insertion. As the resin pressure increases the loss of resin into bedding planes and vertical fractures in the rock increases. As the annulus size increases the mixing of the resin paste and mastic becomes less efficient. Thus, the lower and upper limits of the optimum annulus size is determined by insertion pressure and mixing considerations, respectively. Previous U.S. Bureau of Mines researchers have concluded that a 0 125 inch annulus is optimal. However, others have recently reported that a 0.095 inch annulus with special rolled deformation (SRO) bolts provide superior anchorage to standard rebar with a very large 0.250 inch annulus, attributing SRD resin loss in weak ground to oversized holes. The effect of annulus size on unit length pull strength and resin loss to fractured rock was investigated. Short encapsulation pull tests with resin annuluses of 0.125 and 0.095 inch resisted an average of 2.25 tons per grouted inch, with no significant variation. However, annulus size has shown a dramatic effect on the magnitude of resin lost to simulated rock fractures. No. 5 standard . No. 6 standard, and No 7 J-Bar rebar were inserted into two different viscosity resin cartridges designed for 4 foot boll encapsulation into a one inch inside diameter metal tube, To simulate a rock fracture, a 0.250 inch diameter orifice was located near the capped end of the tube Resin loses increased as annulus size decreased, with a minimum loss of 35% and a maximum loss of 60% associated with 0.125 and 0.095 inch annuluses, respectively.

Jan 1, 1999

By M. Karmis

mining factors and representative ground movement parameters. Based on this analysis, the previously developed prediction methods were modified and tested for their applicability in the Appalachian coalfield. Finally, in order to facilitate the implementation of the prediction methods, as well as the data processing of the monitoring program, a number of computer software were developed and will be discussed in the paper. Surface deformations above underground mines and their prediction and control have been the topics of an extensive research effort by Virginia Polytechnic Institute and State University over the past few years. During the initial stages of this research, a number of case studies were collected from the literature, the mining industry and various government and state agencies and, based on the analysis of this information, appropriate prediction methods were proposed (Goodman, 1980; Webb, 1982; Hasenfus, 1984; Karmis et al., 1984). Although the prediction methods were based on sound concepts, it became evident that their accuracy and implementation were a reflection of the size and quality of the collected case studies. In this respect, the data bank was rather insufficient and posed certain questions regarding the development of subsidence information due to inappropriate length and spacing of monuments used in subsidence surveys, density and accuracy of such surveys, lack of monitoring horizontal movements, etc. In an effort to alleviate these problems, a comprehensive monitoring program was initiated in the coal mines of southwest Virginia, which included: - Two longwall and five room and pillar mines. - In total, seven longwall and sixteen room and pillar panels. - Monitoring lines in excess of 35,000 feet. - Vertical as well as horizontal measurements. A high accuracy digital computer tacheometer was used in all surveys and the type and spacing of all monuments were in accordance with well accepted guidelines. The data from this monitoring program completed the initially collected data bank and, thus, enabled a much needed statistical analysis between

Jan 1, 1987

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By Rodger Fry

All coal deposits contain anomalous geologic conditions which have an impact on roof control, Run-Of--Mine (ROM) coal quality and production costs. To remain competitive in today's coal market and provide a safe working atmosphere, mine operators need to know in advance of mining the geologic conditions which prevail in the coal deposit. In order to identify geologic anomalies within a coal seam and surrounding roof rock in advance of mining, the Radio Imaging Method (RIM) survey procedure has been developed. This paper describes the RIM procedure and how it is used to predict various geologic conditions within a coal deposit. Figure 1 illustrates the RIM in-mine and surface surveys which can be used in an underground mine. [ ] RIM is an electromagnetic (EM} wave process which consists of in-mine and surface survey techniques. Both techniques are used in underground coal mines to detect faults, interbedding, sandstone channels, and thinning coal. Thesurface survey can also be used to determine seam correlation and continuity in strip and underground mining. In-mine and surface surveys work by propagating EM waves along straight paths through the coal. As the RIM signal travels along a ray path, it interacts with the seam material and surrounding rock. This interaction causes the signal to lose energy thereby decreasing its strength along the path. The amount of energy loss per unit path length depends upon the coal seam height and type of surrounding roof and floor rock. A reading of the signal level is taken at the end of the ray path at the receiver location. This reading is used to determine the loss (attenuation) rate of the signal along the path. The signal level data is compiled and analyzed through computerized algorithms which construct images of any anomaly present. This graphical depiction of the coal provides a basis for further geologic interpretation. By comparing the images reconstructed by the RIM analysis to in-mine geologic mappings made while mining through RIM study zones, it has been confirmed that RIM can help detect the following; Rapidly Thinning Coal Incompetent Roof Rock Poor Floor Lithology

Jan 1, 1984

By Rajendra Singh

In India, pillar mining is contributing more than 90% of underground production which involves extraction of a part of coal from bords with pillars around as natural support in the development stage. #Liquidation of these pillars with splitting and stooking, broken nature of face during mining under complex geomining factors like massive roof, varying treatment of goaf and over or underlying workings result in high stresses and deformation in and around the neighbouring piilars, causing operational problem and hazards to mine safety. This paper suminarises the results of three case studies of depillaring under shallow depth with or without stowing. Assessment of nature and amount of mining induced stresses and deformation was done under these conditions, by insitu instrumentation and observation at three depillaring panels of Girmint. Samla and Lachhipur collieries of ECC at 54, 90 and 110 m depth cover respectively. The value of induced stresses and associated deformations was comparatively low in well caved and stowed waves, whereas for massive roof the roof fall followed overriding of pillars and stooks, with very high value of induced stresses and deformaton in absence of stowing. The stress in the centre and outer edges of the pillars changed with respect to depillaring face advance or splitting of pillars. The caving panel of Girmint colliery under weak coal measure formation, showed maximum induced stress in the pillar at 4 m distance from the face which was 1.2 times (16.6 kg/sq.cm) the preminlng stress of the area. The main roof fall over partially stowed goaf of Lachhipur colliery under massive roof strata caused overriding of pillar after crushing 39 stooks of 7.5 x 7.5 sq.m in rythmic sequence with development of 133lsq.cm maximum induced stress. Well stowed Waf of the same panel reduced this value of abutment stress to 2.3 times (65 kg/sq.cm.) body stress after 40 m further advance of the face from the crushed zone. The depillaring at Samla colliery even under massive roof strata induced low stress, equal to 0.8 times field stress only under the same condition with stowed goaf. The studies revealed the effectiveness of stowing in the goaf over loading of pillars and stooks.

Jan 1, 1990