Search Documents

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

"In the mining industry, high-level commitments to adopt sustainability have been made at the corporate levels of mining companies, but there continue to be problems when attempts are made to adopt these high-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into day-to-day minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies. A proposed methodology to achieve integration of sustainability at the operational level will direct the systematic and rigorous identification and characterisation of sustainability issues in an operation. The methodology allows different approach strategies for assessment, comprehensive accounting of sustainability indicators and has the ability to identify sustainability issues which may have significant business implications that cannot be identified using traditional analysis processes."

Jan 1, 2011

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

By Charles A. III Cravotta

Streamflow and water-quality data for the northern part of Swatara Creek, which drains a 112-km2 area in the Southern Anthracite Field of east-central Pennsylvania, indicate iron, copper, and lead, and to a lesser extent manganese and zinc, are transported with suspended particles during stormflow conditions. During stormflow conditions, concentrations of these constituents typically peak prior to peak stream stage as a result of scour and transport of streambed deposits. In contrast, sulfate is transported mostly as a dissolved ion. Concentrations of sulfate, specific conductance, and pH are inversely related to streamflow, indicating dilution and acidification during stormflow. This effect is attributed to the mixing of poorly buffered stream water having pH 6.0-6.5 with weakly acidic storm runoff having pH 4.0-4.5 and low dissolved solids.

Jan 1, 2000

By P. L. Webster, S. D. Thompson

Sevim and Wang (1988a) have presented a model for designing haulage systems in underground coal mines. The authors contend that their model uses a heuristic algorithm to optimize various haulage system parameters. In reality, it would be nearly impossible to optimize a haulage system, because mining plans are uncertain and often change with respect to time. Therefore, haulage system design poses both a stochastic and a dynamic design problem, and its optimization appears to be well beyond the scope of heuristic algorithms. In regard to the authors' design model and its practical significance, a number of additional issues warrant further discussion and clarification. These issues include: l) their model's alleged advantage over simulation models, 2) the correctness of their belt network design, 3) the correctness of their bunker design, 4) the necessity of their proposed bunker clearance policies, 5) the correctness of their shaft-bottom bin design, and 6) the

Jan 1, 1991

By R. Poulin, A. Lamontagne, N. Tassé

This paper presents the results of a laboratory investigation aiming to verify the concept of co-mingling of waste rock with layers of compacted tailings. Overall, co-mingling is expected to delay the onset and reduce the magnitude of acid mine drainage (AMD) production in waste rock. To denionstrate the efficiency of the method proposed, five different column tests have been set-up. Columns were fed with deionized water at the top and drainage waters were collected and analyzed. Bacteria counts were done on the tailings and waste rock after the column tests. Permeability in saturated conditions and capillary parameters were measured for the tailings. The results obtained show that the co-mingling method would be effective in mitigating AMD by maintaining nearly water-saturated conditions in compacted tailings, thus reducing oxygen supply in waste rock by preventing thermal air convection and minimizing oxygen advection and diffusion.

Jan 1, 2000

By Paul Hosford, B. Thrall

There has been a surge of exploration activity and interest in mineral properties located in cold Northern climates, with gold and copper properties as the two most attractive targets. There are already a number of mining operations located in the Arctic, for example, Red Dog, Polaris, and Lupin, all located in the Canadian Arctic. The logistics of sustaining operations, the engineering design and construction methods for such inhospitable regions are now relatively well understood. However, at least three of the proposed new mines in the Yukon Territory, Canada are designed to be heap leach operations. Rescan Engineering has recently completed Feasibility studies for two heap leach operations in the Yukon, one of which, the Brewery Creek Mine, is now in operation. The purpose of this paper is to explore some of the engineering and operating concepts that have been developed to make heap leaching an appropriate process method for gold recovery in a cold climate. Many of the readers will be familiar with the general and specific details of heap leaching, and it is not the intention of the authors to deal with any of the established "do's" and "don'ts" that have been addressed in numerous previous papers, but only with those pertaining to cold weather operations. This paper also examines these design concepts in specific relation to the results of the first winter's operation at Brewery Creek Mine, the first "far" North heap leach operation.

Jan 1, 1997

By Robert B. Hopler

For many years the explosives industry was a technological enigma: it was at the 'cutting edge' of some technologies and in the backwaters of others. For example, for at least the past 85 years, the industry routinely measured time to one-millionth of a second for determining the detonation rate of explosives. At the same time, however, formulations were usually hand-written in 'formula books,' such as the alchemists may have done. Also, due to the fact that the equipment had proven to be safe, many of the mixers and packing machines in use until recently were those patented in the 19th century; improving efficiency was not worth the possible risks that might be encountered. In recent years, the wide availability and portability of computers and their adaptation to specialized applications have revolutionized the explosives industry, much as it has many others. With the advent of the water-based emulsions and slurries (water gels), and the necessity to design totally new processing and delivery equipment, the opportunity arose to apply modern techniques to many aspects of the business. Table 1 lists some computer applications currently in use by explosives manufacturers and end users. The use of high-tech production controls, equipment design aids, field measurement devices and other computer applications is so pervasive in the industry today that any brief article such as this must be considered only as a broadbrush overview of the subject.

Jan 1, 1994

By Jacob Feld

Introduction The best way to eliminate the possibility of rapid excavation in tunnel work is to start an argument between Owner Engineer and Contractor. And arguments are readily started when work is progressed without a frank open agreement on the rules of the game. Fifty years ago a tunnel contractor took a job to excavate and line a tunnel, providing all labor and materials under the guidance and continuous instruction of the Engineer who provided all survey work, checked each new heading and set the lines for the next round of drill holes, usually designed and ordered protective measures, kept record of progress and controlled payment for the work. In my first job in a tunnel, muck cars were loaded by hand and hauled by donkeys. Progress was, at today's criteria, not rapid. The Contractor or in the case of a large concern, his executive field representative was always at the site, knew most of his men by name, and there was a mutual feeling of respect between him and the Engineer in charge of the work. Misunderstandings were cleared up when they came up, expeditiously and fairly, even though satisfaction was not always expressed. The Owner came for the ground breaking and usually for the holing through shot. The Owner had full reliance on the Engineer's ability and integrity. The Engineer recognized the Contractor's expertise in being able to man the job and produce results.

Jan 1, 1974

By Philip U. Santacroce, James H. Meinholz

INTRODUCTION The Milwaukee Metropolitan Sewerage District (MMSD), is a special purpose sub-regional agency that provides collection and treatment services for sanitary wastewater for an area of 420 square miles (1088 km2) in 27 municipalities in the Milwaukee, Wisconsin metropolitan area. During its almost 75 years of existence, it has constructed 464 km of intercepting sewers, the majority in tunnel, and two sub-regional secondary wastewater treatment plants. The present program, the $1.7 billion Milwaukee Water Pollution Abatement Program, was started in 1977 and developed from ongoing internal planning, the Federal Clean Water Act and court judgments. Elements of the Program include improvement and expansion of the two treatment plants; rehabilitation of older in-place sewers; building new interceptors and relief sewers and providing capacity for high volume storage in approximately 32 km of deep, large diameter rock tunnels; reducing combined sewer overflow; and disposal/utilization of the solids that remain after the treatment process. The construction phase of the Program accounts for $1,105,900,000 within 335 separate construction contracts, 211 let to date, and covers a span of 15 years, starting in 1979 and running through 1994. Conveyance System construction cost is estimated to be $650,000,000 or about 60 percent of the total. Through December 1986, in terms of dollars, the total construction program is about 38 percent complete with Conveyance at 34 percent complete.

Jan 1, 1987

By Z. Eisenstein, H. Heinz

INTRODUCTION Contemporary underground transit systems often require cross sections which are not adaptable to shield tunnelling. Due to the frequently large dimensions of these cross sections, which are normally situated at shallow depths and in soft ground, full face advance is not feasible because of ground control and construction requirements. Ground deformation and face stability are controlled by "staged excavation", which consists of sequentially driving smaller, specially arranged, individual headings hence avoiding full-face excavation. Shotcrete is normally used for initial support and these tunnels are frequently described as applications of the New Austrian Tunnelling Method (NATM). Figure 1 illustrates the relative size of large cross section tunnels with respect to conventional shield tunnels. Within the scope of this paper, 'large' cross sections are defined as those whose continuous (i.e., without intermediate pillar support) cross sectional excavated area exceeds 60m2. This definition includes most double track highway, railway and subway tunnels, subway stations and some single track railway tunnels. Excavation schemes which have been more frequently used for continuous cross sections (i.e., with no intermediate pillars) are presented in Figure 2. This classification is an extension of that presented previously by Eisenstein et al. (1986). The symbols used for classifying the excavation schemes are formed by the letter T (for "type"), followed by a number, which represents the number of excavation stages fully embraced by a shotcrete ring, termed "cells" by Lessmann (1986). The numbers inside the cross sections in

Jan 1, 1989

By Faruk Oksuz, Clay Haynes, David Egger

The United States Army Corps of Engineers (USACE) has committed to solve a major drainage problem in the suburban Chicago community of Griffith, Indiana. The Cady Marsh Ditch is currently undersized and on occasion spills its banks causing flooding and economic setbacks to the community. Preliminary studies have identified both tunnel and surface solutions as being attractive and viable. The USACE has decided that this project is an opportunity to use the design-build contracting approach to maximize ingenuity in project approach and to allow the market to dictate whether a surface or subsurface solution is most attractive. The tunnel would be over one-mile in length through sands, gravels and clay. Water control will be an issue during tunneling. The paper will explore the contracting approach to the project and the adaptation of Underground Technology Research Council (UTRC) guidelines for underground contracting to a design build project. The roles of Owner, Owner’s consultant, and design-build contractor will be defined as interpreted by the USACE and key contract provisions will be described and contrasted with a traditional design-bid-build approach to tunnel construction.

Jan 1, 2003

By Frank Palkovits

All technologies move through a cycle from infancy to maturity. Thickened tailings have moved into the young adulthood phase of its development. Many mining companies like the idea of reducing their water-taking and water disposal issues. This limits the risks associated with traditional surface water-covered tailings facilities and the reduced dilution possible through underground disposal of thickened or paste tailings. Just as home theater systems advertised as ?plug and play? are rarely quite that straightforward, implementing and improving a thickened-tailings system has its challenges. However, the technology has also developed in recent years so it is more accessible. Some success factors have emerged because of the new technologies. Is thickened tailings the right solution? The first step in success with thickened tailings should be whether it is, in fact, the right solution for a particular mine. And, if so, what type of thickening is best. The answer depends on several factors, including: ? Grain size: The grain size that is optimal for maximizing mill recovery is some-times not suitable for thickening. Other mineralogical factors, such as mica content, may also influence whether the tailings are suitable. ? Water issues: Available water does not always have the purity necessary for the process. Another issue to consider is that if water is in short supply, as is increasingly often the case, thickening may be a way to reduce the need to both take and dispose of water.

Jan 1, 2008

By Jacques Monette

Gold and silver cyanide complexes are presently desorbed from activated carbon by means of hot caustic elutions. These solutions may or may not contain additional sodium cyanide. There are several parameters which affect the rate of stripping. Some of these include pH, ionic strength, and tempera­ture. Stripping is conducted in recirculating (ZADRA) or once through (AARL) circuits. This paper describes the development of a new chemical eluant which increases the rate of stripping of both gold and silver cyanide complexes from carbon. Two case history applications are described.

Jan 1, 1995

By Tim Wolf

The paper "Weld Notch Affects on Pulley and Belt Conveyor Reliability" has done an excellent job of describing theoretical fatigue and fracture mechanics methods used in modern weld design. From this foundation, we intend to further detail areas previously discussed and present new research in the application of these principles to pulley weldment life prediction. Affects of changes in alternating stress range, mean stress, and residual stress have been investigated using controlled laboratory fatigue tests on a pulley weldment. Comparisons between these results, weld codes, and theoretical fatigue predictions will be made and discussed.

Jan 1, 1998

By Zhang Zhitie

The limitations in mechanism research of mineral comminution in the past and the basic features of the comminution process have been analyzed. Two kinds of catastrophe model, i.e., cusp model and swallowtail one in the mineral comminution have been put forward. The dissipative structure of the mineral comminution: entropy production rate, extra entropy, extra entropy production and system stability has been discussed. The physical nature of the behavior that an old structure was destroyed and a new one was produced in the mineral comminution process has been brought to light.

Jan 1, 1995

By Charles E. Scott

The molybdenum industry has been in a depression since the beginning of the decade. Real molybdenum prices are significantly reduced from 1979-1980 levels when there was a perceived capacity shortage and continued expectations of burgeoning demand. Primary capacity brought on stream since then has been unable to operate profitably and indeed, in light of high inventories and reduced demand, has been largely unnecessary. Structural changes in the molybdenum industry will be needed in the future to weed out superfluous capacity and to expand demand through new product applications.

Jan 1, 1986

By Huo Zuzhao

The main feature of caving methods is to draw ore from the overlying waste rock. Research on the movements of ore and waste plays a very important part in reducing ore loss and dilution and raising the economic benefits. This paper gives the basic theory of computer simulation of ore-draw, exposses the physical significance of mathematical model, puts forword a new formula of similarity characteristic value, brings forth a method of adjusting similarity, introduces the major functions of the simulation program and describes the ore draw control and stope parameter selection through computer simulation.

Jan 1, 1986

By J. -C. Roegiers, M. Thiercelin

Accurate toughness determinations are difficult to achieve in the case of soft or heterogeneous rocks. The existence of a large process zone ahead of the crack tip makes the determination of the apparent toughness crack length dependent, in the case of subsized specimens. In order to use practical size specimens, the authors propose a new toughness test, the Modified Ring Test, which pre- vents a largely developed process zone to form ahead of the crack tip. This test has also the advantage that its geometry is core-based. Numerical and experimental results are discussed.

Jan 1, 1986

By Milton E. Wadsworth, M. Ken Han

The kinetics of leaching of galena in hydrochloric acid solutions with sulfur dioxide gas have been investigated experimentally. The leaching method is then applied to complex sulfide concentrates to evaluate its selective leaching capability and to develop a new hydrometallurgical lead extraction process based upon the method. The leaching reaction follows a linear rate with an activation energy of 61.9,KJ/mole. The rate Is of first order with respect to the product [H+] [Cl-] . Excel lent selective leaching capability f s demonstrated and an attractive hydrometallurgical process flow sheet is proposed.

Jan 1, 1989