Search Documents

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By J. Koinig, K. Mussger, St. Reischl

Jet grouting is a viable supplementary measure for NATM tunneling in special softground conditions. In particular it is used as a type of forepoling to maintain face stability and to provide initial support for large openings until the shotcrete lining reaches sufficient strength. For this purpose cement grout is injected under high pressure through horizontal pipes outside of the tunnel perimeter and thoroughly mixed with the soil producing 1 to 3-foot diameter cylindrical beams. Excavation of the tunnel then proceeds beneath this umbrella of 40 to 50 foot long beams. Design and construction experiences from recent projects are presented for tunnels diameters between 30 and 50 feet in fill and alluvial and colluvial deposits.

Jan 1, 1987

By J. M. Mutmansky

The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous-miner-generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory-generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared.

Jan 1, 1995

By Daniel J. Kennedy, George W. Klinowski

A significant portion of each mine is ventilated with the help of auxiliary fans delivering fresh air to the faces of its developing headings via flexible or rigid ducts. Quality and volumes of air delivered to the blind working faces are essential for creation of safe and acceptable conditions for employed crews. Well designed and properly maintained delivery systems are necessary in each mine. The Cape Breton Coal Research Laboratory, part of the Canada Centre for Mineral and Energy Technology located in Sydney, Nova Scotia, Canada, developed a tracer gas based technique which provides fast and accurate evaluation of any auxiliary ventilation system performance. In addition, important information about the system's behaviour is gathered which can be used for designing a similar system in comparable conditions.

Jan 1, 1989

By A. Aubut, A. Proulx, O. Tavchandjian

Results obtained from conditional simulations and multiple indicator kriging were compared in the assessment of two different mining methods proposed for the extraction of the down-dip extension of a nickel-sulfide ore body located in the Thompson mining camp, Canada. An enhanced turning band simulation algorithm, supplemented with an unfolding technique, was used. A floating stope optimization process was used to effectively compare tonnage and grade figures. A calibration exercise was also conducted in the upper portion of the ore body. This study demonstrates that conditional simulations provide better spatial models for conceptual mine design and capital budgeting decisions.

Jan 1, 2004

By David F. Gibson

This paper presents an outline of several models that have been developed to aid surface mine planners evaluate alternative mining methods and dragline sizes. The models presented belong to a larger group of models that are incorporated in the SEAMPLAN computerized mine and reclamation planning system. SEAMPLAN was developed in the College of Engineering at Montana State University. Initial funding for the development was derived from the USDA Forest Ser- vice and EPA. Enhancements to SEAMPLAN are currently being funded by DOE (Contract DE-AC22-80ET-14173). SEAMPLAN is a comprehensive surface mine and reclamation planning tool that contains a number of major modules: Data Entry and Review, Production Analysis, Reclamation Analysis, and Impact Analysis. The Production Analysis Module contains programs that enable the user to evaluate alternative methods of removing overburden in a surface coal mine and then to assess auxiliary activities required to support the overburden removal operation. A set of these programs addresses the use of draglines for removing overburden. Six basic dragline mining techniques have been modeled. For one-pass dragline operations four methods can be analyzed: (i) simple side cast, (ii) side bench, (iii) extended bench, and (iv) extended bench with side bench. Two methods of two-pass operations are modeled: (i) single dragline, and (ii) tandem draglines.

Jan 1, 1982

By Ping Xia, Yaoxin Lu

With productivty increment. it becomes very important to monitor the underground production environment. This paper presents a multi-level computer monitoring and managing system, which was specially developed for the mine. In this system, TF-200, Industrial Standard Buses (STD) and 32 bytes Super micro-computer were integrated into one body as hardware; Data Base was designed by means of software engineering method in the software development; on maitenance of the system, the parameters are managed concentratedly and data are classified to process; therefore, the ystem gets to the advanced level in China. The system is composed of four sub-stations: Signal Transmission. Data Collection, Data Processing and Image Display Sub-system. Signal Transmission Sub-system(STSS) A frequency-division transmission method is used. Data Collect ion Sub-system (DCSS) Industrial Standard Buses (STD) is used. It can change data from STSS into suitable form for DCSS, Calculate average value every minute, decide alarm and transmit data to DPSS. Data Processing Sub-system (DPSS) The host is a S/120. With UNIX Operation System. the data from DCSS can be classified. stored, displayed. printed, by means of real-time and time-division processing. Additionally the functions of the historic data search and data analysis are provide. Image Display Sub-system (IDSS) The real-time and historic data was displayed for curves and diageams on screens. This system has been in operation.

Jan 1, 1991

By R. Y. Wan

Newmont Gold has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for the pretreatment of low-grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the preg-robbing characteristics of the carbonaceous matter in the ores. Therefore, an alternative heapleach process using ammonium thiosulfate was developed to extract gold from these preg-robbing bioaxidized ores. The ammonium thiosulfate leach process was successfully applied in both laboratory and pilot plant tests. Satisfactory test results were achieved, encouraging the continuation of process development.

Jan 1, 1997

By V. Roze, R. N. Parkinson, R. Shepherd

The alphaDOSIMETER is a complete, integrated system designed to monitor the immediate worksite of underground miners where the disintegration for radon daughters is a risk to the health of mining personnel. The dosimeter weighing little more than one pound is worn by each miner throughout the entire shift and is powered by the miner's cap lamp battery. After this integration period, the unit is connected to a reading network whereupon the day's data is dumped, calculated and stored. Beginning in July 1980, prototype units were subjected to vigorous underground testing in uranium mines in Canada and the United States and in tin mines in Cornwall, U.K. The testing results are summarized and proposals advanced for a typical mine monitoring system utilizing the alphaDOSIMETER.

Jan 1, 1981

By S. Page, R. Bhaskar

The development is described of a real-time tracer gas sensing system for use in fell-scale laboratory studies of air flow behavior around mining machines. A semiconductor sintered tin-dioxide gas sensor is used for gas analyses. A data acquisition and analyses software specific to the sensor characteristics was also developed as part of the system. The system permits the study of transient behavior and assists in obtaining a better understanding of the movement of air around mining machines and in the study of the effect of potential airflow modification devices on the dust exposure of face personnel. It seeks to replace the current method of using a centralized infrared gas analyzer that polls several sampling points using an array of solenoid valves and gas line purgers. The polling results in a significant time lapse between the first and the last set of readings. The system described in this paper has the advantages of real-time sampling and safe operation.

Jan 1, 1992

By H. Colijn

The ever increasing price of bulk commodities forces buyers and sellers in world markets to take a more careful look at methods for obtain¬ing accurate accounting of commodity trans¬actions in commerce and material utilization in processes. Depending upon the application of a sampling and weighing system or the use intended, inaccuracies can result in an eco¬nomic loss of income or a loss in quality of the process. It inevitably results in a loss of control of ones costs. The accuracy of samp¬ling and weighing systems is today extremely important, as they are recognized to be the key components of the overall management system designed to provide both quantitative and qualitative control. This paper will be confined to the weighing systems only and will deal with various as¬pects of system design, calibration and opera¬tions. Special emphasis will be placed on new developments and requirements in this field.

Jan 1, 1988

By M. Misra, J. Nanor

The removal and stability of arsenic over a wide pH range (3.0-10.0) from synthetic solutions and industrial waste effluents (including mining waste tailing slurry) can be accomplished with addition of impure lanthanum chloride alone or in conjunction with ferric sulfate. The long term stability of these correspond­ing precipitated compounds is critical from the disposal stand­point. In this paper test results of this new process for arsenic removal and stabilization from the above mentioned systems are presented. Also, precipitated arsenic compounds (lanthanum arsenate, lanthanum-ferric arsenate, ferric-lanthanum arsenate and ferric arsenate) from synthetic solutions have been charac­terized. The characterization technique used was XRD. XRD patterns which shows that the lanthanum arsenate and lan­thanum-ferric arsenate formed in acidic and alkaline pH at room temperature are crystalline. On the contrary, ferric arsenate and ferric-lanthanum arsenate compounds formed under the same conditions as lanthanum arsenate were amorphous.

Jan 1, 1998

By David R. Wayman

This paper summarizes environmental compliance and related issues associated with underground construction and tunneling operations, whether new work or rehabilitation. Underground construction and tunneling operations have (in most cases) both an underground and surface component. Since many of the major tunneling projects occur in urban areas, often is areas inhabited for several decades or centuries, environmental problems may already exist in a project area, though that may not yet have been formally recognized. Large projects often attract more than their fair share of regulator attention. This paper addresses the issues with the greatest potential to be encountered by underground constructors, with the emphasis on minimizing contractor liabilities, both in the short- and long-term. Minimizing contractor liability begins with understanding bid documents, contract provisions and necessary means of protection, and carries through project execution by responsible control of hazardous materials, avoidance of media contamination, proper waste disposition, as well as compliance with other environmental requirements.

Jan 1, 1999

By A. Dan Rovig, C. Kevin McArthur

Technical and managerial innovations in the minerals industry have allowed continuing mining activities in the United States, and elsewhere, as gold orebody quality has diminished or has become more refractory. Of course, world markets, permitting requirements, and political processes also have created a need for innovative practices that contribute to the survival of the mineral industry. The gold industry has been transformed, during the past approximately 40 years, from a predominantly underground mining and milling type of exploitation and extraction to the large-scale, relatively low-grade type of extraction that is common in the United States today. Indeed, with the introduction of gold heap-leaching technology and the development of mines that produce from large, relatively low-grade gold orebodies in the western United States, a "new" industry was born and continues to prosper today. It is worthwhile noting, however, that Dobra (1997) has reported that one of the major trends in the North American gold industry is a movement back toward underground developments.

Jan 1, 1998

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By David Logan, Sigurdur Finnsson

This project, which is intended to provide effective sewerage services to the Blue Mountains community, is located in the Blue Mountains National Park, about 60 km west of Sydney, Australia. The sewerage scheme consists of about 40 km of tunnels, out of which approximately 22 km have been completed. This paper describes the last major tunnelling operation on this project, the Hazelbrook to Katoomba tunnels. These tunnels, which mainly traverse the Hawkesbury Sandstone formation, are being excavated by a new 3.4 meter diameter Jarva Mk12C TBM. The mucking system consists of a continuous conveyor, which has allowed for some very impressive advance rates. The paper will consist of three main sections; the general geological conditions expected along the tunnel will be described in the first section. The second section will discuss the design and main features of the TBM, back-up system and continuous conveyor. The third section of the paper will describe the operational aspects and various performance data of the machine.

Jan 1, 1995

By William A. Holgate

Coal production in the in the Powder River Basin began its tremendous expansion during the boom of the mid-1970s. New mines were opened from 1976 through the early 1980s. This expansion soon placed Wyoming at the top of the list of coal producing states, where it has since remained. Mines are operated by large companies, with safety and production having equal priority. These mines have been some of the safest ever in the coal industry. Many Sentinels of Safety Awards have gone to them. Safety programs are varied, but there are commonalities. Mine safety at Wyodak Extra training is required of all supervisors. The company offers to pay for any additional first-aid training that employees participate in. Safety departments conduct weekly safety talks. All employees receive the monthly magazine Family Safety and Health compliments of Wyodak. Electricians receive extra training on electric wheel motors, from General Electric. Equipment operators receive extra training from Dresser.

Jan 1, 1994

By Julian Boldy

The discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage haloas a lithochemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 107-m (350-ft) level. This case history is presented in the context of its time and was the first volcanogenic ore deposit to be discovered utilizing mercury as a pathfinder in the Canadian Precambrian. The case history also illustrates that the practical application of an innovative technique coupled to a new geological interpretation can result in success, even on a property that was centrally located in a mining district and had undergone intensive exploration efforts over a 38-year period.

Jan 1, 1991

By Robert L. Cascio

The mining industry uses a large amount of electric power. Their equipment is subject to extreme environmental conditions and mechanical shock. A significant number of electrical accidents are a result of improperly grounded electrical equipment. Federal regulations require the safety ground bed resistance to be measured once a year or after modifications. Most commercially available instruments used to measure the ground bed resistance require the ground conductor to be disconnected and the power system disconnected for safety reasons. The "fall of potential1' method requires auxiliary ground rods and approximately two hours to complete the test. Although a new instrument was initially thought to measure the ground bed resistance immediately without isolating the ground bed, field tests have shown this method is not accurate. In some cases, a continuous measurement of the ground resistance is desired. A monitor has been developed and is presently being evaluated at several mines. These installations will be discussed.

Jan 1, 1992

By Lynn B. Hales, Randy A. Ynchausti

Because of the high economic value associated with small improvements in the operating performance of mineral processing plants, innovations in instrumentation, stabilization and expert control systems have been an ever-present part of the landscape in plants throughout the world since the I 960s. Expert control systems are computer programs that continuously monitor plant conditions; contain "expert knowledge" concerning the process, equipment and operational knowledge; and make timely recommendations for new process set points or even directly change the process set points to achieve desired management goals. Early rudimentary expert control systems first appeared in the early 1970s. They have grown from small, experimental but ambitious projects in which single unit operations were controlled to plant-wide systems that include technologies used in the U.S. space shuttle program. Experiences and results of applying these systems throughout the world will be explained discussed and analyzed. Typical results will be outlined and the use of expert control in the future will be projected.

Jan 1, 2000