Search Documents

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By S. R. Rao, J. A. Finch, E. El-Ammouri, K. Ngoviky, P. A. Disten

Sludges produced by lime treatment of acid mine drainage (AMD) can contain significant quantities of base metals which represent both a potential hazard and a loss of values. A new technique for metal recovery from sludge is proposed by combining selective acid leaching and adsorption of metal ions by activated silica sol. The process is demonstrated on two AMD sludges, one containing primarily nickel and the second zinc. They were first treated with sulphuric acid (pH 3.5) to selectively leach the target metals and then activated silica sol was added to the leach solution to adsorb the nickel and zinc. Thickening and centrifuging gave about 90 percent rejection of the input volume to effluent. The adsorbed metals were redissolved by strong acid into a concentrated solution relative to the feed and the silica sol was recycled.

Jan 1, 2000

By James R. Runkle

Studies in eastern Ohio, northern West Virginia, and southwestern Pennsylvania determined whether subsidence caused by longwall mining influences soil moisture and tree growth. Soil moisture was measured both over new longwall panels and over an unmined control area throughout the growing seasons of 1990, a wet year when the panels were excavated, and 1991, a dry year. No significant effects of mining could be detected. Tree growth was studied in two pairs of woodlots. In each pair, one woodlot was located over a longwall panel excavated about 1980 and the other over an unmined area. Differences in tree growth between mined and unmined areas were neither significant (for most species) nor consistent in direction. The above results imply that if mining does have impacts they are likely to be highly site-specific and localized such as by disruptions of springs or soil slippage.

Jan 1, 1986

By Timothy C. Richmond

The Stillwater District is located in south central Montana approximately 75 miles southwest of Billings, the state's largest city. It lies along the northeast front of the Beartooth Mountains and is within the boundaries of the Custer and Gelatin National Forests. The district contains some of the nation's most spectacular mountain scenery. Montana's highest peaks, including 12,799 foot Granite Peak, rise a few miles south of the area. Much of the district is located on a gently undulating plateau which averages 8500 ft. above sea level, broken by hills up to 10,000 feet and slashed by glacially carved canyons, some of which are more than 3,000 feet deep.(Fig. 1) Immediately to the north and east, the land falls away to the Great Plains, stretching unbroken to the Mississippi River. Two major tributaries of the Yellowstone River, the Stillwater and Boulder Rivers, traverse the area and several large streams originate in the district itself. Access to the high mountain country and the adjoining Beartooth Primitive Area is restricted to a few horse and jeep trails continuing from the terminus of improved roads in the bottom of the Stillwater and Boulder Valleys. Hunters, fishermen and cabin owners make intensive use of the area along its improved transportation routes, but hikers seldom venture more than three miles beyond the end of the roads. People from the Billings area are the most frequent visitors.

Jan 1, 1974

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By Eileen Ashworth

Introduction A study was completed that investigated the enrollment in mining engineering programs in 24 universities and colleges. All programs considered in the study award four-year bachelor of science degrees in mining engineering. They also provide all the engineers for the mining industry and a large portion of the geotechnical engineers working on environmental problems, storage of hazardous waste, civic, and Federal government underground projects. The numbers used as the base for the study are those reported by each program to SME-AIME and published yearly (SME, 1986). Data for the study came from the period 1975-1985. Also, since some programs include students in related disciplines and special categories, such as cooperative students, a few inaccuracies were unavoidable. A 23-page document has been prepared that reports on the overall picture of current enrollment, the trends, and discusses the results, perceived effects, and what can, or should, be done. There has been an obvious, and dramatic decrease in total undergraduate enrollment since the late 1970s. In 1978, 3117 students were enrolled. In the 1985 fall semester, enrollment was 1022, less than one-third. There were 485 seniors, 265 juniors, 147 sophomores, and 125 freshmen. The downward trend in total enrollment is likely to continue for at least another two years. Class size The catastrophic drop in enrollment is shared by all programs across the country. It does not discriminate between types of programs, coal or hard rock mining, or location. In general, 1985's enrollment is about 30% of whatever the maximum enrollment was in any program, though this varies from the teens to 50%. The latter percentage occurs only for some programs with special circumstances, particularly new programs not well established in the late 1970s. The beginning of the decline in enrollment has occurred at slightly different times as affected by the demise of each program's local industry. The numbers in each class produced from a specific freshmen year (Fig. 1) are worthy of comment. The dramatic drop in enrollment for all classes after 1982 is clearly demonstrated. The timing coincides with the general downturn in the mining industry, when many employed engineers were laid off and new graduates could not find jobs. Also, significantly fewer students are being attracted to mining programs as freshmen. The number of seniors shown seems inappropriate. Where did so many seniors come from and why are so few graduates produced? There is an increasing trend for students to take four-and-a-half or five years to graduate. Therefore, they are counted twice, once when they are first classed as seniors and again the following year. Some students purposely delay graduation to obtain more summer work experience and take additional courses. They believe that this gives them a better

Jan 8, 1986

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024

By Karoly (Charles) Kocsis, Jeff Johnson, Felipe Calizaya, Tulio Dias, Natanna Nunes

Two pressure balancing chambers were constructed at a Colorado coal mine to reduce the risk of spontaneous combustion. Each chamber was established by installing a Kennedy stopping at about 10 ft (3 m) in front of an isolation seal, and equipped with two safety doors, a nitrogen injection system, and a set of environmental monitors. Several pressure balancing tests for different ventilation conditions were conducted in these chambers. During each test, pressurized nitrogen was injected into the chamber and the pressure differentials across the stoppings and seals monitored. This study presents a summary of the results achieved, lessons learned, and the basic requirements to operate a pressure chamber effectively.

Feb 1, 2024

By K. V. Raj, VASU GANGRADE

Airflow in large-opening stone mines is largely dependent on the natural ventilation due to the large cross- section area of the opening. The openings of such stone mines are typically twice or thrice the size of typical underground coal or metal/nonmetal mines. Due to the influence of natural ventilation, air velocities as well as the static pressure drop in the mines are low. Mines rely on auxiliary fans to ventilate active faces to reduce contaminant exposure to mine workers. The National Institute for Occupational Safety and Health (NIOSH) is conducting research on ventilation of large-opening stone mines to reduce worker exposure to dust and other contaminants such as diesel particulate matter (DPM). In order to reduce worker exposure to dust and DPM, an understanding of the airflow pattern due to auxiliary fans in the mine is needed. Under this research, NIOSH researchers are exploring the computational fluid dynamics (CFD) modeling to understand the airflow behavior in large-opening mines. In this paper, the team is presenting the results from three-dimensional CFD modeling of airflow in a large-opening stone mine and investigating the effect of a fan placement with the movement of trucks.

Feb 1, 2025

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977

By Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes, borehole geophysical logs and surface geophysics. Several case studies are presented to illustrate this application.

Jan 1, 1980

By Dan G. Wasyluk, Meryl J. Klassen, Tony J. Morris, Clive H. MacKay

The Rogers Pass Project in British Columbia has involved the construction of two railway tunnels totalling 16.6 km and a 345 m deep shaft. Systematic geological mapping was carried out at four headings during construction. The paper discusses the procedures used to record the geology, structure, rock mass characteristics and excavation performance. Coded data from the geological mapping and shift inspector reports was entered into a computer data base. The rock mass quality was evaluated for both the Geomechanics and Q classification systems. Continuous computer generated graphic logs were produced showing the excavated perimeter map, geological parameters, installed support and construction activities. The tunnel logs were updated on daily basis and used during construction by project staff for evaluating support requirements and monitoring excavation progress. The specific requirements, difficulties and advantages in mapping tunnels using a computer based system are compared to those of a conventionally mapped tunnel excavation with hand drafted tunnel logs.

Jan 1, 1987

By A. Palit, M. K. Mohanty

This investigation has concentrated on optimizing the newly developed Pansep linear screen and developing empirical models to predict the screening performance. Most empirical models developed in the past to predict the performance for industrial screens are suitable for the vibratory screens. Understandably, these models are deficient in predicting the performance of linear screens due to the difference in their operating principle. Thus, the main objective of this study has been to develop empirical models suitable for linear screens to predict the partition coefficient for a given size fraction as a function of the aperture size. The inadequacy of the conventional model equation originally developed for vibratory screen has been demonstrated and a modified equation developed to predict the partition coefficient as a function of the normalized mean particle size (d/d50c). In addition, new model equations have been developed for linear screens to predict the screening efficiency as a function of the separation size(d50) and to predict the separation size as a function of the screen aperture. It is believed that these model equations will be useful for the plant operators in selecting the mesh panels of correct aperture size and in predicting the product size distribution based on the selected aperture size.

Jan 1, 2003

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil Corp. (now part of Atlantic Richfield Co.) in the period 1.965 to 1968. The results of the work show that presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. This has implications for several types of retorts. Correlation of the results of this work with that of other investigators shows that the partial pressure of retorting products in contact with oil shale during retorting has an effect on yield. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to await commercialization of another process. The existence of a plant in which to test prototype size would markedly reduce such development costs. Results Preliminary development work with the apparatus was carried out using a fluidized bed of sand, as explained later, with the entire system brought up to temperature and flows stabilized. The shale was injected rapidly in a slug (batch) which had small mass compared to that of the high temperature system to make the reaction approach isothermality with reasonable approximation of instantaneous preheating. Typically, the temperature in the center of the bed dropped from 900°F to 600°F one minute after batch addition. It returned to 750' within three minutes and 900° within seven minutes. Obviously, the bed was quenched but it recovered rapidly. Average bed temperatures of 700' to 1020°F were examined to compare the effect of temperature with published results. Yields In the 700°F range were only 10 to 15%, of Fischer Assay (FA). Above about 950'F, oil yields decreased and gas yields increased. Nitrogen was used first as the fluidizing gas to provide a chemically inert medium. Incept for an insignificant dip at 895"F, Figure 1, oil yield was not affected by retorting temperature in the 800° to 900' range as long as residence time was adequate (16 minutes). At 925°F, the oil yield was some 103% FA. With further increase in temperature, the yield decreased to 86% FA at 1015°F. There is no increase in carbon on spent shale, the lost oil goes to Increased gas make.

Jan 1, 1972

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By D. T. Kirkwood

The practice of impounding mine water and liquid fine waste in underground mines is increasing. Often these underground impoundments are created by constructing seals or bulkheads designed to withstand the expected hydraulic pressures. Occasionally seals are built for another purpose, usually to act as explosion-resistant ventilation barriers. Due to factors such as clogged drain pipes or unexpectedly high inflow rates, these explosion-resistant seals sometimes become subjected to hydraulic pressures. The incidence of seal failures due to inadequate design and/or construction is also on the increase. Fortunately, to date, no lives have been lost by water seal failures, but a clearer understanding of the design and construction considerations specific to water seals is vital to keep this from occurring in the future. This paper presents technical considerations for the design and construction of seals which will specifically be required to withstand hydraulic pressures in underground mines.

Jan 1, 1995

"Controlling dust generation and keeping it below permissible limits at the working face of a room and pillar mine is a challenge for mine operators. With the recent changes in the respirable-dust regulation, it has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) stated that a flooded-bed scrubber, under its optimum condition, can achieve cleaning efficiencies between 58 and 90 percent. The performance of such a system can be maintenance intensive. Other industries face similar dust control issues. The University of Kentucky partnered with Toyota Motor Manufacturing for the development of a novel wet scrubber for capturing paint overspray, with capture efficiencies in excess of 98 percent and minimal maintenance. The aim of this study is to assess the ability of this novel wet scrubber to capture respirable dust in an underground coal mine. This paper presents the conceptual design and the computational fluid dynamics (CFD) modeling of this novel wet scrubber. It discusses the results of the CFD simulation performed on the novel wet dust scrubber. INTRODUCTION Dust generation from underground coal mining is an inescapable phenomenon. No matter the practices employed, it inevitably occurs. Elevated concentrations of coal dust are potential health and safety hazards. Although dust in an underground coal mine cannot be completely avoided, its influence can be mitigated through good engineering practices. The effect of dust on the health of mining personnel has had a significant impact. The prolonged exposure of airborne respirable dust (< 5 µm) can cause coal workers’ pneumoconiosis (CWP), silicosis, emphysema, and chronic bronchitis, collectively known as black lung (U.S. Department of Labor, 2014). According to the National Institute for Occupational Safety and Health, black lung has killed more than 10,000 miners between 1995 and 2004 (NIOSH, 2008). In addition to being a health issue, coal dust is also a safety issue to the underground coal miners. The generated dust, if not captured, is dispersed into the mine air through the ventilating air and deposited downwind on the return entries’ surfaces. In the event of a methane explosion, the coal dust, if insufficiently diluted with rock dust, triggers a coal dust explosion which is much more severe than a methane explosion and causes more damage (Kenneth et al, 2006). The Jim Walters No. 5 Mine and the Upper Big Branch Mine disasters which together killed 42 people and resulted in damage worth millions of dollars in property are the examples of coal dust explosions (U.S. Department of Labor, 2001 & 2010)."

Jan 1, 2016

By L. K. Lepley

A marine sonic sub-bottom profiling system and a hovercraft were used in an engineering geophysics survey of the tailings being deposited at the Mercur gold mine. Detailed density sections with vertical resolution of one meter were desired for computations of strength, permeability and potential self-compaction. The logistical problems of conducting a geophysical survey and in collection of geotechnical soil samples from an active tailing impoundment was solved by using the amphibious hovercraft for towing and transport on the impoundment. The "chirp" sonic system produced continuous, real-time geophysical cross-sections with vertical resolution of ten centimeters showing possible trapped gas. The hovercraft provided a platform over water, ice, slurry, and solid beach for collection of geotechnical information and physical samples.

Jan 1, 1994