Search Documents

By S. J. Porter, M. T. McRae

The Melbourne City Link project includes two three-lane highway tunnels, 1.6 and 3.4km long, respectively, which are both approximately 16 meters wide and 9 meters high. The tunnels will be excavated through interbedded, moderately to highly jointed siltstones and sandstones of the Silurian Age Melbourne Mudstone formation over the major parts of their lengths. The strength of the intact rock varies from less than 5 MPa to greater than 70 MPa. Based on the available information regarding the performance of large span tunnels in weak rock, it was considered that the commonly applied empirical design guidelines for tunnel support, based on rock mass classification systems, should be augmented by more explicit design methods. The support design was, therefore, validated by analytical procedures, including numerical analyses, which are described in this paper.

Jan 1, 1997

By Jianliang Li, Jan M. Mutmansky

This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels.

Jan 1, 1992

By LeEtta M. Shaffner, John R. Marks

INTRODUCTION In the last twelve years, underground stoping methods at the Homestake Gold Mine have evolved from open cut-and-fill with jacklegs, cribbed raises and electric slushers to ramp-based mechanized cut-and-fill (MCF) and vertical crater retreat (VCR) with dieselpowered loaders, trucks and drill jumbos. The evolution was swift. Unfortunately, ventilation practices have had trouble keeping pace. Stope ventilation is still too dependent on auxiliary fans and coolers. A single large MCF stope might contain up to eight headings, each of which requires significant ventilation resources when a diesel loader is present. Air is shortcircuited all too frequently through mined-out VCR panels. These factors and the recent rapid decent of the center of mining prompted a study to improve ventilation practices and to more accurately project future requirements. BACKGROUND In 1992, the underground portion of the Homestake Gold Mine produced 8336 kg of gold from 1407 ktons of ore (268,000 oz from 1,551,000 st). The ore is hosted in low to medium grade meta-sediments. Stoping took place from 420 to 2347 m below the surface (1400 to 7700-ft levels). The weighted center of mining was 1662 m deep (5450-ft level) in 1990 and is projected to be 1890 m (6200-ft) in 1993. The deepest level is 2440 m (8000-ft) where the virgin rock temperature (VRT) is 56.1°C (133F). The mine is ventilated by 504 m3/s (1,069,000 cfm) measured at mid-exhaust-circuit density. The air-conditioning system includes an 8.1 MWR (2300 ton) controlled recirculation plant, a 2.0 MWR (580 ton) chilled water plant, a 1.0 MWR (290 ton) exploration drift refrigeration plant, 28 spot-coolers totaling 3.4 MWR (960 tons) and 35 spray coolers totaling 1.5 MWR (420 tons). The mine employs 117 diesel units with a total nameplate rating of 7961 kW (10,672 hp). These units include twenty-four 1.5m3 (2-yd) loaders, twenty-six 2.7m3 (3.5-yd) loaders, fourteen 3.8m3 (5-yd) and two 7.6m3 (10-yd) trucks, and assorted utility vehicles and drill jumbos. THE STUDY In April 1991, the University of Nevada-Reno (Mackay School of Mines) and the South Dakota School of Mines and Technology cooperated with Homestake on an MCF study. Mackay instrumented a stope with thermocouples, air velocity meters and hygrometers (Duckworth, 1992). South Dakota Tech conducted a finite-elements computer analysis of a back-filled MCF stope with/without light-weight shotcrete insulation on the sidewalls and back (Chellam, 1992). Homestake conducted an empirical analysis of deep-level MCF stoping. This paper describes the Homestake study. Twenty-three of the forty MCF stopes deeper than 1800 m were surveyed at least once during the last quarter of 1992. The stopes not included were being cable-bolted or back-filled. Figure 1 shows the complexity of one of the ramp-based stoping areas included in the survey. This particular stope has six separate production headings. A baseline wallrock heat load was derived for each stope or heading from psychrometric calculations. Broken ore, waste rock fill and fissure water were noted when present and the effects included in the baseline heat load. Other heat sources often mentioned in the literature such as metabolic heat from workers, heat from explosives and small electric loads were neglected. Fan heat was considered part of the ramp & crosscut heat load and thus not included in the study. Diesel heat was addressed separately. RESULTS Survey results, plotted as the heat flux against VRT, are shown in Figure 2. The equation for the regression line is: W/m2 = 2.1236*VRT - 75.405 The 0.31 correlation coefficient is poor which implies that the results should be used cautiously. Previous experience strongly suggests that differences in productivity are most likely responsible for the scatter in data points. A rapidly advancing stope will have a

Jan 1, 1993

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By A. D. Davis, G. A. Zabolotney

A ground-water flow model was developed to simulate the postmining recharge rate from precipitation at the Belle Ayr surface coal mine, which is located in the Powder River Basin near Gillette, WY Wyoming state regulations require that reclaimed lands should provide a rate of recharge that approximates the premining rate. Steady-state calibration and transient simulations showed that the postmining recharge rate through spoil is at least 50 mm (2 in.) per year, exceeding the original infiltration rate of 4 mm (0.16 in.) per year to shallow overburden aquifers. Major reasons for the increase include the flat topography of the reclaimed areas and the decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate that is less than 50 mm (2 in.) per year but still somewhat greater than the premining rate.

Jan 1, 1997

By G. D. Schena

A decision support system for the management of the mineral resources of a developing country has been derived. The system allows the evaluation of the impact of a mineral project in a developing country in the broad context of its economy. The analysis permits the assessment of the overall socio-economic consequences of mineral prospects and allows incorporation in the evaluation of issues that are broader in scope than the pure financial objectives. The system is built around the Leontief framework of economic analysis. The original input-output model, enhanced to incorporate country-specific behaviour is integrated with cost-benefit analysis and shadow pricing. The analysis leads to synthetic measures of profitability at market and shadow prices. These measures are useful to direct the mineral policy of a developing country through the exploitation of those mineral resources which are most likely to bring about economic growth and social advancement.

Jan 1, 1992

By J. Craynon, M. Karmis

Previous papers by the authors have presented a systems-engineering approach based on the premise that systems can only be optimized if all factors are considered and integrated into mine planning. This paper discusses the challenges inherent in optimizing the design of large-scale surface coal mining operations in Appalachia. Regulatory and permitting programs in the United States often focus on single parameters, rather than the full suite of desirable outcomes for sustainability. By utilizing geographic information system (GIS) tools to evaluate available data on environmental and social resources, the regulatory barriers which prevent operations from incorporating ecological and other sustainable development concerns into coal mine sustainability performance were identified. By analysis of the on-the-ground issues related to sustainability, the key parameters to be incorporated into an optimized coal mine design in Appalachia are discussed along with possible changes to the regulatory framework that would enhance incorporation of sustainability into coal mine design.

Jan 1, 2011

By W. Haupt, M. Thormé, H. J. Ertle, K. Reim

Though Germany has a very old mining history, her experience in uranium mining only started in the late sixties. Today in the Federal Republic of Germany (FRG) there are only 5 small mines in the exploration stage, namely Menzenschwand and Müllenbach in the Black Forest and Mähring, Popenreuth and GroBschloppen in northern Bavaria. In all these exploration mines much development is required to define shape and size of ore bodies. Mining engineers, government authorities and environmentalists alike are very much concerned about environmental safeguards and protection of mine workers against radon and its daughter products. Miners are affected by internal and external radioactive exposure. In general the external [f3]- and [µ] -exposures can be considered as small in comparison to the internal exposure and are therefore not discussed in this paper. The internal exposure is caused by the inhalation of radon and its daughter products and is relevant to the lung as the critical organ. The nobelgas radon is inert and does not from compounds with other elements easily. Contrary to the physical half-life of 3,8 days the biological half-life of radon is only 10 to 20 minutes. During the rentention time in the body only approximately 1 % of the long-lived decay products are retained in the system (SCHOGER, 1976). In this connection is it important that the radon resorption as well as the radon secretion varies individually and depends to a large extent on the age of the person (SCHOGER, 1960). RENOUX et al. (1978) have determined that the greatest part of the a(-activity in the air is attached to aerosoles with a diameter of 0,4/14. The radiation exposure of the lung by radon is negligible if compared with the exposure by short-lived decay products. For this reason one has introduced the concept of the potential [o](-energy (P) of the short-lived radon decay products, which means the total [ct]-energy, which is produced when an atom decays in the decay-series down to the long-lived lead-210. [ ] The unity of the potential [o]-energy concentration in the SI-system is 1 j/m3 air. In radiation protection however a specific unit is used namely the working level (WL): [ ] The WL-unit, though internationally recognised has not been introduced officially in Germany. Because of the large amount of tunneling still to be done in the FRG, the various mines departments responsible for safety and health in mining ask searching questions such as: - What are the laws governing radon emanation in tunneling? - Can workers be adeguately protected against radiation hazards? - How should one drive through high grade uranium ore? - What happens if the ventilation system breaks down?

Jan 1, 1981

By K. Komnitsas

Activities in the mixed sulphides industry, such as mining and beneficiation, cause adverse impacts to the environment due to excavation, treatment and disposal of low-grade ores and tailings containing residual sulphide minerals. The greatest impact is caused by the oxidation of sulphide phases contained in the tailings and waste rock and the subsequent production of leachates characterized by low pH and high concentration of heavy and toxic elements and sulphates, called acid mine drainage, that contaminates soils, surface- and groundwater. Therefore, rehabilitation of these sites is required in order to render these pollution sources inactive and minimize environmental impacts. The calculation of risk, based on acid mine drainage probability and magnitude of consequences at the disposal sites offers engineers, environmental scientists and authorities a valuable tool for the selection and application of the best remediation technology. Several parameters, such as the chemical and mineralogical properties of the wastes, the most probable pathways the contaminants follow, the potential receptors and the exposure scenarios have to be taken into account. Therefore, risk is the most critical parameter in decision-making regarding management of mining wastes and rehabilitation of disposal sites.

Jan 1, 2002

By Quan Li, Xiang Ren, De Lui, Yumin Zhang

SL-type continuous centrifugal separator with injection flow (Injection Flowing Film Centrifugation, IFFC) for separating fine and ultra-fine minerals has been developed recently in China and it is capable of recovering particles down to one micron in size. In this paper, the principle of its separation is discussed. IFFC is a special transient pulsating film which combines both thin film jigging and thin film concentration functions. It not only can intensify the looseness and stratification of the settled particles, but also create a hydraulic weir effect to improve recovery of fines and ultra- fines and significantly improve the performance of thin film separation. In a Chinese tin gravity concentrator, SL devices, SL-1200s (capacity 1.5-2.0 ton/hr) and SL-600s (capacity 0.5 ton/hr) were applied to treat -1 0 micron cassiterite slime(removed as tailings at the past) and to replace the old tin flotation system(-74+10 micron slime). The plant results show that 50-60% of the cassiterite can be recovered from -10 micron slime with an enrichment ratio of 10-12. Particle down to one micron were recovered. Under optimal conditions, the recovery from -74+10 micron slime can reach more than 85%. The recoverable size range can be determined by calculation.

Jan 1, 1995

By J. Bigu

Ventilation conditions in working environments are usually studied by anemometry or, in complex cases, b using special tracer gases such as SF6 and 85Kr. in conjunction with chromatographic and radioactivity techniques, respectively. In some working environments, such as underground uranium mines, however, use can be made of the natural radioactivity environment (e.g.. 222rn. 220rn, and their progeny) to investigate mine ventilation conditions of practical interest. Theoretical studies and experimental data in several underground uranium mines and mine locations show that certain thoron progeny to radon progeny concentration ratios are very good indicators of ventilation conditions. Furthermore, the growth and decay of radon progeny and thoron progeny provide valuable information on mine air residence and clearance times. Some specific examples have been analyzed, such as bacterially-assisted uranium leaching operations in a partially enclosed stope, and the effect on the underground environment of turning ventilation fans on and off for a period of time. Air residence times and other variables of interest, determined from the mine radioactivity environment, were compared with more traditional techniques, such as anemometry and tracer gas chromatography. These studies were also extended to a wet non-uranium mine which exhibited relatively high concentrations of radon and its progeny.

Jan 1, 1989

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By Steven A. Elmquist

Although past investigations (2, 5)have been conducted to determine crushing relationships, no program which covered a broad range of crushing conditions had been conducted. The previous studies appear to concentrate on small segments of the overall picture and did not fullfill our desired information objectives. The Crusher Variables Research Program conducted at the Mineral Research and Test Center (MRTC) of Rexnord, due to the broad range of variables utilized in a production size crusher, is believed to be the most comprehensive study of its kind as of this date. The principles developed by the Symons brothers in 1925, when they patented the cone crusher as we know it today, are still being used in the machine known as the Symons Cone Crusher, During the development of this novel crushing concept, a technique known as the fall of material (called the Bouncing Ball Theory1 by some) was used to determine an idea as to the proper head angle, eccentric and speed of eccentric rotation, The final variables used for the Symons Cone Crusher design were, therefore, the logical conditions to start with and use as a reference against which other variables could be compared.

Jan 1, 1979

By Ron Robinson

Booster fans have been in regular use in British coal mines since the first half of this century, but a large increase in their use did not take place until after the Nationalization of coal mines in 1947. From that time the need was identified to improve standards of ventilation in general and mining engineers specializing in ventilation were appointed at all levels in the mining industry. A comprehensive approach to ventilation surveys and planning, together with the realisation of the benefits of booster fans, led to their more rapid introduction. Many coal mines in the U.K. are at moderate depth and have virgin strata temperatures of 30°C or less. The ability to control climatic conditions by increased ventilation rather than resort to cooling systems has led to the introduction of booster fans and recirculation systems in these mines. Large makes of methane and high levels of coal dust production due to increased mechanization have also required enhanced ventilation standards. This paper deals with the reasons for selecting booster fans and the specific safety considerations involved in their use. Numbers, types and sizes of booster fans in the U.K. are outlined, together with notes on installation and performance. Remote monitoring and control from the surface is dealt with, and current legislation. The evolution of controlled recirculation is also covered starting with auxiliary fan systems in 1970 and leading to very large district schemes in the late 1980s. The research at Newcastle upon Tyne University and other establishments in the climatic conditions associated with recirculation is summarised and its use in assisting existing and proposed conventional and recirculation systems is indicated.

Jan 1, 1989

By Lloyd H. Yeager

Good morning gentlemen. I'm very pleased to be a part of this fine program for the Society of Mining Engineers. Gypsum, as many of you know, is one of the most unique minerals on earth. The very excellent presentations which you have just witnessed, revealed the geological aspects of gypsum operations. It is not our purpose this morning to pursue this subject further. Instead, we felt you would be interested in some of the uses of gypsum . . . and what the future holds for gypsum products. To help accomplish this, we're going to first show the Gypsum Association's new film, "Shape Of The Future. ' This short movie traces gypsum f ram mines and quarries to its ultimate destination in homes, schools, offices -- in virtually every type of construction. We think you'll be particularly interested in the description of gypsum's fire resistive nature.

Jan 1, 1965

Many of the deeper ore reserves in current gold operations as well as new gold deposits consist of refractory ore types. As process development for these mineralizations remains time-consuming and costly, minimization of exploratory testwork and the early identification of feasible process routes is critical. Since most of the processing parameters are related to the mineralogy of the ore (Marsden & House, 1992), thorough mineralogical analyses during exploration and development phases have become a technical and economical requirement. The determination of mineralogy-related processing parameters and especially the gold mineralogy is even more important for these ore types because refractory gold ores consist of many transitions from partially leachable to totally refractory. In addition to sulfide and gangue encapsulation, various other refractory conditions may exist. Together with accessory mineralogical detriments (e.g., alteration/ slimes, reagent consumers, scale formation, mineral preg robbing) they may complicate process selection and hamper optimal plant operation.

Jan 1, 1993

By J. D. Cooper, D. W. Thompson, J. Basiuk, W. Cass, R. Ilves

The Department of Thoracic Surgery and Pathology at the Toronto General Hospital have had a long standing interest in the early detection and treatment of carcinoma of the lung. Our initial experience was with a population at risk due to a prolonged period of cigarette smoking. More recently our efforts have turned to industrial exposure, specifically in the nickel and uranium industries. [Initial Screening Project] (1) For a three year period 1963 to 1966 a cytology screening program was carried out through the Out-Patient Department. The study was limited to cigarette smokers over 40 in age. A total of 1586 patients were examined. Of the sputa collected, the classification is seen in Table 1. There were 11 malignant sputa present. Added to this number were 25 patients with symptoms, normal chest X-rays, but malignant cells on cytology, and a further 5 patients in whom an abnormality (eventually proven non-malignant) showed on X-ray, and sputum showed malignancy which was radio logically occult. (Table II). This gave a total of 41 patients with malignant sputum who were evaluated between 1960 and 1966. The clinical course of these patients is seen in Table III. Only 19 of 41 patients had localization and treatment of their tumour during that study period and this low rate of localization attests to the technical difficulties endoscopy in that day presented. The method of localization was as follows: a) 6 patients showed an area of segmental pneumonitis somewhere in this time period b) Using the rigid bronchoscope localized the tumour in 9. This was proven by direct biopsy, and frequently required more than one bronchoscopy over a prolonged time period. c) bronchograms and tomograms showed abnormalities in 5 patients. Of these 19 patients, 5 were treated by radiotherapy because of general condition or refusal of surgery. Three of the irradiated patients died of recurrent cancer within three years. The other two died within one year of unrelated disease. Fourteen patients underwent resection, with one operative mortality. At pathology, the tumours were "in situ" in 6 and invasive in 13. There was no evidence of nodal spread. When last followed up in 1979, there were no cases of recurrent tumour and no cases of second lung primary tumours. Similar experiences have been reported from the Mayo Clinic (2), Johns Hopkins (3) and Memorial Hospitals (4). Early detection of radiologically occult tumours which are in situ or minimally invasive has given uniformly good results. There have been no deaths from recurrent or metastatic cancer in surgically resected patients, and only one second primary tumour has been detected. Interestingly, the Hopkins group reports that 5 patients with Stage I squamous cell tumours refused operation. One refused any treatment and died of disease at 12 months. Three were radiated, and were alive from 14-38 months post-treatment, all with evidence of recurrent disease. [Sudbury Sintering Plant Study](5) From 1948 to 1963 an open travelling-grate sintering process was employed to convert nickel sulfide to nickel oxide at an International Nickel Company operation. The environment in this plant was particularly dusty and filled with fumes. It became apparent by 1969 that the incidence of bronchogenic carcinoma was markedly increased in workers from this plant. A concerted effort was made to track down all workmen with this exposure. During 1973 and 1974, 268 men were studied. Chest radiographs were done and showed no mass lesions. Sputum was collected on three consecutive days and analyzed. There were 12 men with malignant sputum, all of the squamous cell variety. Two refused any investigation, one presenting 31/2 years later with extensive hronchogenic carcinoma, and the other 5 years later with extensive carcinoma of the maxillary sinus. In the remaining ten patients careful rhinolaryngeal examination as well as a detailed bronchoscopy, involving examination, brushings and biopsy of all pulmonary segments was carried out. One patient was found to have laryngeal carcinoma and was treated by radiation. In nine patients, the malignancy was localized to the lung, leading to six lobectomies, two pneumonectomies and one sleeve lobectomy at operation. However, the follow-up in these cases suggests a different biological behaviour with these industrially related tumours. While no tumour has recurred locally, one patient has died of metastatic cancer and two patients have developed second and one patient a third pulmonary primary cancer. However, survival has still been much better than wits radiographically manifest lung cancer. [Technique of Localization] (6) Following a careful rhinolaryngeal examina examined and then the lower respiratory tract is examined. This is all performed under general anaesthesia. The trachea is examined with the rigid Jackson bronchoscope, collect-

Jan 1, 1981

By James E. Brewer

Procedure for approval by the U. S. Army Corps of Engineers of a new source of aggregate is in three phases. Phase 1 consists of an investigation of a quarry or proposed quarry by district geologist and laboratory geologist and/or petrographer. The quarry face or suitable outcrop is logged in detail or, if exposures are poor, cores may be taken to determine whether further investigations are warranted. Phase 2 consists of thorough laboratory testing. Cores and crushed material are subjected to a number of acceptance and quality tests for soundness, absorption, abrasion, reactivity, and other properties. Petrographic analysis is also made. Phase 3 is a physical and economic study of the site and involves determining quantity of stone avail- available, amount-and character of overburden, condition of haul roads and distance to rail shipping point, plant flow sheets and capacity, aggregate sizes produced, and approximate price of material at plant.

Jan 1, 1966

By Ignacio Salazar

Somebody sure gave me the wrong title. I can talk much more freely about the impact of the anti-nuclear movement on the DRILLING industry in New Mexico. In a word, it is being "clobbered." It doesn't seem like very long ago that my brothers and I were busy trying to find enough new equipment (and trying to talk bankers into lending us enough money) to keep up with drilling work we could get. Seemed like no matter how hard we worked, and how much money we borrowed, we were always one step behind where we wanted to be. We had so many holes to drill that all our crews were working three shifts a day, and over several states. The nation needed energy, and we were ready to help supply it. Exploration and development drilling jobs were all going full-blast. We had trouble keeping up with them. With luck, we figured we'd be able to get all our equipment out of hock before all the necessary uranium mines were developed.

Jan 1, 1979

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The paper evaluates the attenuation behavior of acoustic emission (AE) signals in four different materials used in marine environments. The study aims to identify materials with the highest and lowest AE signal attenuation, providing insights into wave propagation and structural monitoring in deep-sea mining applications.

Dec 1, 2023