Search Documents

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By F. Grandjacques

INTRODUCTION Selective Reduction of Nickel in Oxidized Ores Oxidized nickel ores, either garnieritic or lateritic, contain much more iron than nickel. The regular carbon reduction in an electric furnace is operated in such a manner that the greater part of iron oxides is reduced simultaneously with nickel oxide, resulting in a low nickel content ferronickel. In order that the nickel content of residual slag may be suitably low, -excess carbon must be fed so that the carbon content of the ferronickel thus obtained is that of casting iron. The metal also contains other impurities such as silicon, chrome, etc. In order to convert the casting iron into slightly carburized ferronickel with high nickel content, the greater part of the carbon and more than half the iron contained therein must be oxidized by means of oxygen. Energy is thus consumed as carbon, and power to reduce iron oxides, and more energy is consumed as oxygen to re-oxidize the iron contained. This method can be economically adopted for nickel ores with grades ranging around 2. 5 to 370, but it gets excessively costly when nickel grade falls below these values. This is why, for nickel ores with low nickel grades and high iron content, studies were conducted to develop a selective reduction process which, while reducing only a small part of the iron oxide, would provide efficient reduction of nickel oxide. Rich ferronickel is thereby obtained, with nickel content ranging around 30 to 50%. Due to the presence of slag with a high iron oxide content, the metal thus

Jan 1, 1979

By J. P. McKinney

Benchtop experiments were performed, in which an electric field was used to enhance separation of water from phosphatic clay suspensions from a central Florida mine. A constitutive relationship was established that relates the increase in solids content to operating time and the applied electric field. An upper limit to the degree of separation was found to be a function of electric field, and the time required to achieve this limiting value was also a function of electric field. The energy requirement for removal of water ranged from 1.25 to 175 Wh/kg water removed as a function of the electric field. A mathematical model was developed that provided good agreement to the experimental values and served to validate the constitutive relationship.

Jan 1, 2011

By E. S. Smith, Sunirmal Banerjee

INTRODUCTION Social awareness of the detrimental impact of man-made wastes on our environment has grown considerably during the last two decades. Increased public and institutional concerns have resulted in the implementation of a wide variety of regulatory controls of disposal of wastes. These regulations have often reflected significant conservatism in expecting guaranteed elimination of pollution risks. This sort of expectation assumed a state of knowledge which was not readily available to the major producers of wastes. The mining industry, in particular, has been affected by such regulations in terms of excessive costs and loss of benefit. As a result, investigations are in progress (1) to generate newer methods for satisfactory stabilization of mine and mill wastes and (2) to apply the available technology to achieve the standards set by the regulatory agencies at reasonable costs. This paper presents a conceptual scheme for stabilization of mill wastes by suitable management of operations and accelerated consolidation of tailings slurries. The main discussion in this paper is aimed at the ability of the proposed scheme to address the major considerations in effective disposal. Comparison in both cost and effectiveness are also made between the proposed scheme and various other currently used disposal concepts. MAJOR CONSIDERATIONS IN EFFECTIVE DISPOSAL The primary objective of an effective tailings disposal scheme is to provide containment of the contaminants in such a manner that the undesirable impact of the wastes on the three basic elements of our environment--land, air, and water-would be minimal. Bearing the above objective in mind, one may justifiably list the major considerations in the choice of the disposal scheme in terms of its effects on land, air, and water (Bromwell, 1976) as follows: Effects on Land (1) whether the scheme makes optimal use of land.

Jan 1, 1980

By Ricardo Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Large (> 100,000 oz.) sediment hosted disseminated gold (SHDG) deposits are often spatially associated with anticlines. Many SHDG deposits are within or closely associated with windows. Windows are erosional manifestations of fold culminations (4-way closed anticlines). Hydrocarbons are often trapped in fold culminations in the Canadian Rockies, and may account for degraded hydrocarbons in many SHDG deposits. In the Eastern Basin and Range Province, Mesozoic anticlines may have been large scale conduits fm gold bearing Mesozoic and Cenozoic hydrothermal fluids which became trapped and/or concentrated at the fold culminations.

Jan 1, 1990

By Debbie Nakamura, Daniel Tempelis, John E. Shamma

The Metropolitan Water District of Southern California established a Board of Consultants to assist them in administering the design and construction of the Inland Feeder Program tunnels. The Board acts as an expert review body for the owner, looking at key issues that can potentially impact the success of the program. The use of the Board evolved over the life of the project, and its composition was modified to better address the needs of the owner, and the Program requirements. The experience, function, and value of such a board is analyzed and discussed in this paper.

Jan 1, 2003

By W. L. Han, Y. D. Zhang, X. C. Li

Meta-systhetic technique for large systems engineering has been placed on the agenda. The meta-systhetic A1 approach should involve the integration of digital and knowledge info, from qualitative to quantitative analysis, etc. Some algorithms of meta-systhetic technique such as ANN-ES and GA-ANN are introduced. A case study follows - mining conditions evaluation by meta-synthetic A1 methods, including: setting up the structure of evaluation indexes system, deciding their grade of membership by ANN-ES algorithm; determining the weight values of evaluation factors by GA-ANN algorithm; and developing the integrated evaluation model.

Jan 1, 2002

By H. Suharyono, M. Lutsky, R. Hogg

Sediment consolidation in highly flocculated suspensions occurs only if the self-weight of the material exceeds its compressive yield stress. A simple model for sediment densification is presented and applied to the simulation of thickener operations. Measured relationships between sediment self-weight and the extent of consolidation are used to establish underflow densities. Supernatant turbidity data provide the information necessary to predict overflow clarity. It is shown that thickener depth can play a role in determining solids-handling capacity as well as dewatering performance. The application of the model to the design and operation of full-scale thickeners is described.

Jan 1, 1995

By A. B. Samaddar

A prototype automated mapping and spatial information management system has been developed, and illustrates how a powerful map manipulation capability and a comprehensive display system can be combined using both raster and vector mapping: The concept of a mapbase and information retrieval mechanism, query language as well as text and graphical menus, is introduced. The Geographic Information System (GIS), which has been built around a system for storage and retrieval of spatial and textual data, allows interaction with geographic space represented on a displayed map. The prototype is demonstrated using maps and information of an open pit mine.

Jan 1, 1989

By Jonathan M. Pachter

Introduction The Bailey mining complex is located in Greene County, PA, in the Talley Run valley. It includes two Pittsburgh No. 8 seam deep mines (Bailey and Bailey No. 2), a coal preparation plant, and two refuse areas. Clean coal is shipped from the complex by way of a 24-km (15-mile) rail spur. It con¬nects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Co. (Consol) began a permitting effort aimed at building the mine. Construction began in Dec. 1981, less than six months after the first application submittal. Clean coal was produced by the Bailey preparation plant in Sept. 1984. Several factors allowed quick permitting at Bailey. Effective project planning, including early formulation of a project planning team, and identification of red flag issues helped. So did innovative responses to environmental questions, and development of environmentally sound project designs. Forming a project planning team Consol management decided that Bailey mine construction had to begin in late 1981. A project permitting team was immediately formed to see that this goal was achieved. Team members included a project manager and personnel from Consol&apos;s engineering, environmental, and operating departments. Communications among all team members was crucial in obtaining the various state and Federal environmental permits. All project permitting team members participated in weekly meetings during application preparation. Discussions at these meetings ranged from recent public contacts, to application content, to environmental design considerations. Establishing a project manager was critical to the team&apos;s success. The project manager was responsible for seeing that permit acquisition, facility construction, and operation of the mining complex proceeded on schedule. The project manager had the final word, mediated disagreements, and frequently served as project spokesman to the public. Identifying red flag issues Red flag issues are those environmental factors with the most potential for delaying the schedule or stopping the project. The first red flag issue identified was organized local opposition. This opposition had completely derailed a US Soil Conservation Service proposal to build a multipurpose dam on Enlow Fork, a short distance

Jan 9, 1985

By R. A. Speirer, T. C. Bettinger, L. P. Richardson

INTRODUCTION The Bureau of Mines (The Bureau) remote sensing researchers at the Denver (CO) Research Center, have been investigating computerized methods to detect and map surface linear features called "lineaments" for ground hazard assessment in mines. Many of these lineaments at the test mine site were found to correlate to subsurface geologic discontinuities such as faults, fractures, and joints that intersect coal seams at depth. These features adverse1 y affect the roof and rib integrity in underground mines, thus contributing to rock failures that may result in injuries to mine workers and loss of production. Advance knowledge of the existence of such hazardous geologic features can aid in mine planning and development. Lineaments may be observed in a variety of images of the earth&apos;s surface. Linear features that can be observed using Landsat mu1ti spectral scanner data (MSS) images range from regional (greater than 3 miles in length) to an intermediate length of from 1 to 3 miles. These images are recorded in discrete radiation bands in the green, red, and near-infrared portions of the el ectromaynetic spectrum. These data are acquired from the EROS Data Center of the U.S Geological Survey, Sioux Falls, SD, in digital format on magnetic tapes that are suitable for processing on certain minicomputers. Shorter lineaments length (less than 1 mile) can be observed in high- to low-a1titude aerial photography, radar, and infrared images with image scale ratios of 1:1,000,000 or less. These linear features can correlate to smaller dimensioned faults, and to fracture and joint sets at the local geologic scale. Other informational sources can help substantiate 1ineament analyses, such as well logs, mine naps, topographic data, and geophysical data acquired over the study site. These data must be in a digital format to process on the "DEC PDP 11/23 minicomputer system1". Data can be acquired in

Jan 1, 1986

By D. M. Larsen, N. D. King

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce dore&apos; at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338°F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1994

By K. N. (Mani) Subramanian

A 2.5 meter diameter column has been successfully used in a 100 tph flotation plant at the Harbour Lights Mine in Leonora, Western Australia, to produce a final gold bearing sulfide concentrate from the ore in a single stage. This pioneering application of column flotation cells to rougher stage was pilot tested using a 11 cm column, which demonstrated column&apos;s capability in rougher, scavenger and cleaner flotation stages. A hybrid circuit involving columns and mechanically agitated flotation cell s was adopted for the commercial installation. This paper describes pilot plant results, design of the plant flotation circuit, and early results of commercial operation.

Jan 1, 1988

By D. D. Misra

The paper presents a computer simulation package developed for the size¬-reduction circuits of Indian hematitic iron ores. The package is developed by linking independent procedures describing different unit operations like crushing, screening, recycling, etc. Mathematical models are used to quantify the unit operations involved. The models are selected after thorough analytical studies of the samples and data collected from four operating plants. The package developed gives a fairly accurate result with respect to, size and chemical composition of the flow stream and products. The program written in PASCAL can be used to try the flowsheet with various raw ores, as well as different flowsheets with the same raw ore.

Jan 1, 1989

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By Robert A. Jankowski, Charles Babbit, Natesa I. Jayaraman

The Bureau of Mines, together with Foster Miller Inc., has developed a compact, high pressure scrubber system for continuous miners. Powered by water energy alone, it can move up to 1.4 m3/s (3,000 cfm) of air and scrub a significant amount of the dust in the air. Full- scale model and underground trials showed excellent performance. Operated at 8.3 x 10[3] kPa (1,200 psi) and 38 L/m (10 gpm), the scrubber has reduced operator and return dust concentrations by more than 50 pct. This paper describes the full-scale model development, system fabrication and underground evaluations of this novel and inexpensive scrubber.

Jan 1, 1989

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002

By Stephen R. Brown

The principles of quality management are well developed and, from a practical stand- point, thoroughly implemented in the process industries of Japan. Although these principles are now applied to the U.S. manufacturing industry, and as a result, the steel industry, they have been largely ignored in the non-ferrous and precious metals industries. This paper presents the concepts and practical approaches to implement a total quality management program. Contrary to the beliefs of many managers, such a program increases yields, recoveries and output while it decreases unit costs. In fact, quality management incorporating statistical process control will be an essential ingredient for metallurgical plants to effectively compete in the &apos;90&apos;s.

Jan 1, 1991

By M. G. Ayat, J. W. Leonard

Introduction Coal preparation plants are continuously losing clean coal in their refuse and contaminating their clean coal product with impurities. This is due to the lack of a system by which the immediate efficiency of the cleaning operation can be determined at any given time. Moreover, the advantage of developing tagging/ tracing techniques would be a reduction in the time and money spent in evaluating the performance of advanced cleaning techniques. Currently, conventional sampling and testing, on-line analyses, and computer information systems are the major tools with which engineers analyze and control the efficiency of processing plants. Conventional sampling and testing is an effective analysis technique but it is slow. On-line analysis provides information on quality parameters rapidly, but these parameters do not provide all of the necessary information. The use of tagged particles in coal preparation plants may provide the necessary link between diagnosis and the application of computers to process control. In this work, a novel technique that uses tagged particles to generate partition data is presented (Leonard et al., 1982). Individually prepared tagged particles are added to the feed and detected in the product or refuse port of specific gravity based processes. Providing that a computer can interpret the output of a detection device and trace particles with predetermined physical properties through the coal preparation plant and that the trace particles actually represent desired raw material, sufficient partition data can be provided for computer analyses and control of processing efficiency. Coal tagging technique The use of tagged particles in coal preparation operations are in the early stages of development. Though there is a brief history of particle tracing in the mineral processing industry (Gardner et al., 1986; Foreman and Amundson, 1976; Poston et al., 1962), the concept has not yet been applied to the analysis and control of processing plant operations. Several methods for tagging coal particles have been identified. These include magnetic, radioactive, and fluorescent techniques. As far as the magnetic tagging of coal particles is concerned, a method has been developed to manufacture synthetic magnetic particles of various sizes and specific gravities. Ideally the synthetic particles would have identical size and density as the coal particles being separated.

Jan 1, 1988

By R. T. Webber, D. Moffett, D. W. Averill, G. H. Kassakhian

INTRODUCTION In Canada, radium-226 is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate barium-radium sulphate. Large settling ponds are provided to effect solid-liquid separation. However, the barium-radium sulphate precipitate [(Ba,Ra)S04] is a fine, slow-settling crystalline solid which is not easily removed by simple sedimentation systems. Consequently, settling pond effluents may contain appreciable quantities of particulate or suspended radium-226, depending upon the specific pond system and/or the time of year considered. Also, current technology is expected to be incompatible with ultimate disposal goals since safe recovery of the barium-radium sulphate sludge from the settling ponds may be difficult to achieve (IAEA, 1976). Under the auspices of Environment Canada, a Government-Industry Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical--chemical treatment systems as an alternative to settling ponds. In response to the Sub-Group recommendations, a bench scale feasibility study began in March 1976 at the Wastewater Technology Centre (WTC) of Environment Canada. The bench scale work was expanded and accelerated in 1977 with financial assistance provided by the Atomic Energy Control Board. The results of this study indicated that coagulation and flocculation of the (Ba,Ra)S04 precipitate greatly increased settling rates (Wilkinson and Cohen, 1977). Subsequently, a research program with a larger scope was initiated in January 1978; this program is jointly managed and funded by government and industry as indicated in Table 1. The principal goal of the Joint Government-Industry Program is the development of a physical-chemical process to reduce the radium-226 content of uranium mining and milling effluents. The following effluent radium-226 activities were established as targets for the program: 0.37 Bq/L (10 pCi/L) as total radium-226; 0.11 Bq/L (3 pCi/L) as dissolved radium-226. Process development work was undertaken at bench scale at the WTC and at

Jan 1, 1980