Search Documents

By Vljay K. Chhipa

Artificial intelligence is" an emerging technology in the field of computer application. Expert system have been developed to imitate human intelligence and reasoning process. Expert systems have much scope of application in the decision making process in mineral exploration as such decisions are highly subjective and expert opinions are very helpful. This paper presents a small expert system to analyze reasoning process in exploring for uranium deposits in sandstone.

Jan 1, 1989

By Gordon R. Wicker, Willem P. C. Duyvesteyn, Robert E. Doane

A versatile acid leach process has been developed which is applicable to a broad range of oxide nickel ores. Inherent in this process are high recoveries of nickel and cobalt, as well as a relatively low energy consumption. These features extend the range of economic exploitation of laterite deposits to low grade limonites and to garnieritic ores not suitable for pyrometallurgical processing. Particular advantages can be realized in treating orebodies containing both limonite and garnierite and ores containing significant amounts of cobalt.

Jan 1, 1979

By A. Geoffrion, L. J. Cousineau

In underground powerhouse excavations, the access to the horizontal sections of the penstocks is most often critical. Other factors which influence the schedule include: the sequences of excavation, the interface dates between contracts, the type of support for the overhead cranes and whether the roof in the powerhouse is a reinforced concrete arch or a suspended prefabricated material. At Outardes 3, Churchill Falls and LG-2, these factors, along with the size of the powerhouse and the local topgraphy and geology were studied to produce the optimum schedule.

Jan 1, 1983

By Charles H. Tiernon

Separation of particles on a table deck* results from differences in specific gravity, plus a number of other interrelated phenomena: size of particles; shape of particles; stratification (consolidation trickling); and hindered settling. The effective use of these factors may be controlled and aided by the following table adjustments: differential action of the drive or head motion; speed of motion; length of stroke; side tilt; end elevation; size of deck area; shape of deck; character of deck surface; riffle design; amount and distribution of wash water; feed water-to-solids ratio; feed rate; and feed uniformity. The typical concentrating table used in the US coal industry is essentially a rhombohedral-shaped deck supported by a suitable subframe. It generally slopes in the direction of the short axis, tilts upward at the refuse end of the long axis, and is differentially reciprocated in the direction of the long axis. This head motion tends to move the particles longitudinally toward the end of the table. At right angles to this movement, wash water (distributed along the high side of the table) tends to move particles down the slope parallel to the short axis of the table. Hence, the natural path of a particle on a concentrating table is from the feed box corner to the diagonally opposite corner of the deck (Fig. 1). There is a natural tendency for heavier particles to sink to the deck of the table and for lighter particles to stay nearer the surface. As a consequence, the heavier particles are carried further along the longitudinal axis since, being on or near the surface of the deck, they are more affected by the table's reciprocating action. The lighter particles, being at or near the top of the moving bed, travel slower in a longitudinal direction and thus separate from the heavy particles. Wash water and the diluting water in the feed cause lighter gravity particles to move down the short axis of the table. The feed material then fans out from the feed box, where it enters onto the table with heavy gravity particles moving in one direction and lighter particles moving in another. By properly adjusting all of the previously mentioned factors, a clear-cut separation is possible between high- and low-gravity particles, or between refuse and coal. Riffles are of great importance to tabling. They create considerably more capacity than is possible with smooth decks, and they are responsible for better separation accuracy. Particles in their downward movement along the deck's slope are delayed behind the riffles. Hindered settling, consolidation trickling, and other phenomena occur as the particles tumble over the riffles and stratification ensues. The heavier particles settle to the deck of the table and are trapped behind the riffles, thus insuring their positive movement toward the end of the table. Since stratification and separation of particles are not complete as a result of any one riffle, a series of riffles are used. The cycle of stratification and hindered settling is repeated from riffle to riffle. The result is purer products as particles fan out and progress forward and downward over the table. The smallest, heaviest particles stratify downward to the surface of the deck more quickly and are carried out by table movement toward the refuse end at a faster rate than coarse, heavy particles. Light gravity, larger pieces ride on the top layer of particles and flow down the deck's slope as a result of the cross flow of wash water at right

Jan 8, 1980

By Donald R. East

The impacts of the economic storage or disposal of mill tailing wastes are becoming more important to the mining industry as environmental regulations become more demanding. Mill tailings have long been considered the stepchild of the extraction process and have not, until recent years, been treated as a separate entity of the mining and milling process with distinct and complex physical and chemical characteristics. As a waste product, the economic value of mill tailing is usually very small whilst economic and the environmental liabilities can significant. be Disposal of tailing is commonly identified as the single most important source of environmental impact for many mining projects.

Jan 1, 1990

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column, and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. The results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed.

Jan 1, 2003

By Allan D. Fernie

Many long conveyors, 2 - 20 km plus, have been installed over the past 10 years. Conveyor belt life, depending on the conveyor length and material handled, will generally range from 10 - 15 years. To replace long conveyors splicing one or two rolls into a conveyor run on an intermittent basis can be prolonged in an operating system involving considerable downtime and scheduling problems. This paper presents some of the methods used to- date and highlights forward planning for such an event. Special belt handling equipment required and the execution of a belt change operation are described in detail. Wright Engineers Limited have worked in collaboration with Canada Conveyor to design and implement the methods described herein.

Jan 1, 1993

By David D. Gallagher

Customer demand for greater efficiency and reduced operational costs on modern overland conveyors has focused attention on the conveyor belt's rolling resistance properties. Studies have indicated as much as 60% of the power losses on a long horizontal conveyor can be attributed to the indentation of the pulley cover rubber as it passes over idlers. This paper will compare tan delta values of different compounds with large scale rolling resistance test data from the University of Hannover. Results will then be compared to actual power consumption data gathered on several long overland conveyors using identical belt construction except with different pulley cover compounds. Concluding comments will be made indicating substantial operating cost differences based on the rolling resistance of the cover compound.

Jan 1, 2000

By J. C. Yingling

An approximate analytic- model is developed for minerals liberation when comminution processes are applied to multi-component ores, i.e., ores that include grains of multiple mineral species. The model employs a one-dimensional representation of ore texture similar to that employed by King (1979) and Klimpel and Austin (1983). The spatial texture representation is viewed as being generated by a stationary semi-Markov process. Associated semi-regenerative processes are defined that can be used to establish, approximately, the joint distribution of particle size and composition, where composition refers to the identities and relative proportions of mineral species included within the particle. Numerical predictions made by the model are compared to size and composition distributions observed in previous experimental studies.

Jan 1, 1992

By P. Tsang, S. S. Peng

Mine floor failures, such as floor heave and floor buckling, occur frequently in underground coal mines where soft mine floor exists. The types of failure can usually be classified into two categories; shear punching failure and tensile failure. A model based on the Winkler's elastic foundation is proposed in this paper for floor stability analysis. The model considers material properties of floor strata, in-situ horizontal stress, pillar size, entry width, and configuration of multiple-entry system and predicts stress conditions in the mine floor based on given in-situ mining and geological conditions, as well as deformation of the mine floor. This information is used to predict possible failures of mine floor by comparing the strength of mine floor with its stress condition. The validity of the model is verified by in-situ data described in this paper.

Jan 1, 1992

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to pining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1992

By George W. Luxbacher

The inclusion of a new term "planned subsidence" in the Surface Mining and Reclamation Act of 1977 has lead the U.S. coal mining industry into a new aspect of engineering: subsidence planning. Subsidence planning has necessitated the integration of geotechnical, civil, and mining engineering disciplines. Although much of the foundation and application work has been completed, subsidence planning is still a developing area. This paper discusses the application of subsidence planning in several brief case studies (a high voltage transmission tower, a sewage treatment plant, and a slurry impoundment), emphasizing the risk assessment aspects necessary to account for some of the uncertainties that may exist.

Jan 1, 1986

By Steven A. Tesdahl

Maintenance means keeping equipment running or restoring it to operating condition. However, the 21st century will usher in a broader need for equipment management, a cradle-to-grave strategy to preserve equipment functions, avoid the consequences of failure and ensure the productive capacity of equipment. Profitable future mining operations will have reduced the 35% of operating costs typically spent on maintenance and the unfavorable impact of downtime that often multiplied these costs by 300%. They will survive those operations that tried to carry outdated "maintenance" thinking beyond the year 2000. These surviving operations will have applied modern management techniques, technology and information to align the efforts of people with the needs of equipment. Future managers will use equipment management as an integral part of an overall production strategy. They will see it as a means of raising productivity, improving performance and minimizing downtime to maximize profitability. This global thinking will characterize all operations planning to survive in the competitive world of mining of the next century.

Jan 1, 1998

By B. Denby, R. Hollands

Mine information is often multi-disciplinary, dynamic and spatially complex. Different departments use the same data in many different ways, information changes over time and mines change their shape continuously. Earthworks InTouch is a radical VR-based system developed by AIMS Solutions and marketed by Earthworks, which provides a rapid and intuitive interface to a wide range of mine information. VR is used to provide an interactive and visually accurate, dynamic 3D model of the mine workings and equipment operating in the mine. Individual objects in the mine can be linked to external applications that provide up-to-date and context sensitive information. Equipment movement can be simulated or tied in to real-time survey from GPS systems for example or excavator productivity data can be extracted from a production database. The paper will highlight the major advantages of using such a VR interface to access valuable and time sensitive information.

Jan 1, 2002

By Misra M., P. Grimes, Chen. S.

The combustion of petroleum products produces emissions which contain oxides of nitrogen (NOx), hydrocarbons (HC), and particulate matter (PM) which have adverse health and environmental effects. In recent years there has been increasing interest in the use of water-fie1 emulsions as a substitute for conventional fuels. Emulsified fuels are emulsions of water in fuel, which are typically made of 10 to 20 percent of water mired with certain additives and fuel. Studies have shown that the emulsified diesel can significantly reduce the emissions of NO, PM and car- bon monoxide and increase the fuel efficiency. In order to produce a stable diesel emulsion, the development of an effective surfactant additive is critical. The stability of diesel emulsions is influenced by many factors, including size distribution of the droplets, the viscosity of the continuous phase, the physical properties of the interfacial film, and temperature. This paper describes a method to produce emulsified diesel and combustion results obtained from various tests. It has been found that the diesel emulsion made with this additive package was stable during the test, and the emissions were lower in NO, CO, and PM compared to the baseline diesel.

Jan 1, 2005

By J. Gallagher

Henderson Mine has been transporting molybdenum ore using a rail haulage system for the past 21 years. Due to the age of this system, limited performance, and obsolescence, a capital investment decision was imminent. Henderson used this opportunity to evaluate other transportation methods and continuously improve their mining practices. These efforts resulted in a new mine plan for Henderson, which ensures that Henderson will continue to supply high quality molybdenum into the 21st century. This paper will discuss the dramatic changes taking place at the Henderson Mine as a new production level is mined. These changes include the installation of an underground crushing, conveying, and truck haulage system, as well as increasing the scale of the panel caving process. Each of these topics will be discussed, as will their rock mechanics and material flow implications.

Jan 1, 1998

By Samuel M. Brock

Problems related to strip and auger coal mining have grown with the development of the industry and the economy. New technology has produced equipment that has made mining by surface methods not only highly productive, but potentially highly destructive of water resources and natural environments. On the other hand, growth of the economy has produced an increased demand for clean water, and created new demands for amenity values that natural environments provide. Thus, opposing forces have created conflicts in resource use. And these conflicts have made surface mining highly controversial. Resolving the controversy will require the solving of complex economic and social problems. The essence of the economic problem created by surface mining is that, in the absence of proper regulation, substantial costs resulting from the process are borne by the public rather than the mine operator.

Jan 1, 1968

By III Scotland

Genstar's underground mine at Texas, MD experienced a failure of the mine roof and subsequent damage to an underground backfill caused by surface floodwaters. A hydraulic backfilling program was developed in house to stabilize temporary repairs to the mine roof, replace 2300 yards of pneumatically stowed backfill, and complete a permanent repair to the mine roof. A flowable backfill material was developed, tested, and later marketed as the result of experience gained during this project. In addition, Genstar personnel developed backfilling techniques to meet the requirements of the repairs and completed work without the additional expense of non company services or contractors.

Jan 1, 1992

By R. L. King

An expert system is a computer system that performs tasks that are considered by most people to require human expertise. Since their functioning relies heavily on large bodies of knowledge, they are often referred to as knowledge-based systems. These systems can contain the skill and knowledge of an individual human expert or the combined knowledge of a group of experts. The knowledge embodied in an expert system can consist of specific facts, HSHA regulations, heuristics or rules-of-thumb used by the expert, and databases. The purpose of this paper will be to introduce the participants in the ?Increase Competitiveness Thru Innovation? session to expert systems. This introduction will enable the participants to better appreciate the balance of the papers to be presented in this session. These papers will deal with specific mining problems and a proposed innovative solution. This paper will discuss such topics as problem-solving paradigms, rules of inference, knowledge representation, and the structure of expert systems.

Jan 1, 1989