Search Documents

By A. Haghighat, B. Lattimer

"Mine face ignition due to a high levels of methane is one of the most common fire incidents in underground coal mines. This work exams ignition scenarios in continuous miner headings. Depending on the magnitude of the ignition or resulting fire, the ventilation curtain in the continuous miner (CM) heading may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to the ventilation curtain on the ventilation flow into the CM area. The computational fluid dynamics software Fire Dynamics Simulator (FDS), Version 6.0 was used to predict the conditions that develop due to a 200 kW fire in the coal mine face following a methane ignition with different levels of curtain damage. Smoke layer depth, temperatures and mass flow into the CM area were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed of the curtain. Partial removal of the curtain allowed more smoke to accumulate in the CM area and a reduction in ventilation into the CM area. With full removal of the curtain, the smoke accumulated through the entire depth of the CM area and flowed out the entrance to the CM area and the ventilation completely bypassed the region. INTRODUCTION Active working faces in underground coal mines are one the most hazardous locations in terms of fire events. According to Mine Safety and Health Administration (MSHA) data analysis, the highest number of non-fatal fire incidents was reported at mining faces, intersections and crosscut areas in comparison with other locations from 2000 to 2012. About 464 fires happened at active working faces from 2000 to 2012, most consisting of a methane ignition, in some cases followed by localized fire. These are high risk incidents due to the potential to raise float dust and damage ventilation systems, particularly auxiliary systems such as curtain or tubing. Depending on the magnitude of the ignition or fire, the ventilation curtain in the continuous miner (CM) area may be damaged or dislodged, affecting the ventilation into the area. Five computational fluid dynamics (CFD) scenarios were considered to investigate the smoke layer depth, temperature, visibility, mass flow rate, and the behavior of airflow in an entry with a continuous miner (CM) located in it. The state of the auxiliary ventilation was varied based on the assumption that as an ignition increases it magnitude it will affect ventilation curtain proportionally. Visibility and temperature along the height of the entry at different sections were investigated and the interface height at each section was determined. Also, the fresh air height was studied for tenability analysis in future. FDS, Version 6.0 was used to predict the conditions that develop due to a 200 kW fire on the coal mine face following a methane ignition with different levels of curtain damage. Smoke view software was used as the post processor to visualize and analyze methane fire behavior at the face. Most entry fires are reported as fuel-controlled fires as they are rarely restricted to air access (Ingason et al, 2014). The working face fire in the following models was assumed to be a fuel-controlled fire."

Jan 1, 2016

By M. L. Mellish

In 1989, for the third consecutive year, both the production and consumption of coal in the United States reached record levels. Domestic coal consumption totaled 806.5 Mt (889 million st) in 1989, a 5.4 Mt (6 million st) increase from the year before (Table 1). US coal exporters also had a banner year. For the first time since 1982, exports ex¬ceeded 91 Mt (100 million st). US coal production in 1989 rose by a surprising 27.3 Mt (30 million st), reaching 889 Mt (980 million st) for the year. To a certain extent, the sizable difference between production and demand growth was due to smaller consumer stock withdrawals. Coal consumers withdrew only 12.7 Mt (14 million st) of coal from their stocks in 1989, com¬pared to 22.7 Mt (25 million st) in 1988. Despite strengthening coal consumption, exports, and production, coal prices to all domestic sectors declined slightly during the year. That essentially continued the trend of the past several years. On the labor front, the United Mine Workers of America struck the Pittston Coal Group in 1989. It was a bitter work stoppage that was not settled until February of 1990. This was the first major coal strike since 1985. The strike also precipitated a series of wildcat outages by UMWA members in June and July. At their peak, more than 40,000 UMWA members participated in the wildcat strikes. Except at Pittston, however, most miners were back to work by August. It is estimated that perhaps 4.5 to 9.1 Mt (5 to 10 million st) of coal production was lost due to the Pittston and associated wildcat strikes. However, some of this production may have been recouped by other coal companies not affected by the wildcat strikes, and by the affected companies after the strikes ended.

Jan 1, 1990

By A. B. Cecala

Video technology coupled with datalogging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. these techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties. the Helmet-Cam is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a datalogging dust monitor. these are worn by the miner in a backpack, safety belt or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data filesare downloaded to a computer and then merged together through a NIOSH-developed computer software program called enhanced Video Analysis of Dust exposure (eVADe). by providing synchronized playback of the merged video footage and dust exposure data, the eVADe software allows for the assessment and identificationof key work areas and processes, as well as work tasks that significantlyimpact a worker?s personal respirable dust exposure. the Helmet-Cam technology has been tested at a number of metal/nonmetal mining operations and has proven to be a valuable assessment tool. mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed eVADe software will be available for download at no cost on the NIOSH website.

Sep 1, 2013

By Kim B. Shedd, Erin A. McCullough, Donald I. Bleiwas

"The earliest known use of cobalt was to make blue glass in Mesopotamia before 2000 B.C.E. Since then, innovations across many diverse industrial sectors transformed cobalt into an essential commodity for contemporary society. The physical and chemical properties of the element cobalt and its alloys and compounds make them indispensable for a variety of applications, including aircraft engines, hybrid electric vehicles, machine tools, missile guidance systems, petroleum refining and smartphones. As a major industrialized nation, the United States is a leading consumer of cobalt and cobalt-containing products. However, with few exceptions, U.S. cobaltcontaining ore deposits are of low cobalt grade. Historically, U.S. cobalt mine and refinery output have not met domestic cobalt demand. As a result, U.S. cobalt chemical and alloy producers need to procure most of their cobalt from the international market, which can become susceptible to supply risk.The 1978 Cobalt Crisis illustrates supply risk. At that time, the Democratic Republic of the Congo (DRC) (then known as Zaire) was the world’s leading producer of mined and refined cobalt. An insurgent invasion of the country’s copper-cobalt mining region during a period of high cobalt demand and low producer inventories caused a temporary supply shortage in the international market. The monthly average cobalt spot price increased from $18/ kg ($8/lb) before the crisis to $99/kg ($45/lb) seven months later. The high price and concern about potential disruptions in supply prompted manufacturers to reduce or substitute for cobalt where possible, and encouraged increased recovery of cobalt from scrap. The DRC has regained its position as the leading producer of mined cobalt globally and continues to be characterized by high governance risks (U.S. Central Intelligence Agency, 2015; World Bank, undated). This article will present current and historical world cobalt production trends, which can help inform discussion about the variety of international supply chain risks consequential to its trade."

Jan 12, 2017

By Todd Burchett

Mining engineers spend countless hours and resources when designing a new underground coal mine. Their primary objective is to design the safest and most efficient operating mine with regards to coal production. A key variable often overlooked in this design stage is the slope conveyor. Typically, a slope conveyor is expected to operate with a 98-percent or higher availability. However, too often little effort is put forth by the mining engineer to optimize its design. Coal companies will rely on engineering, procurement, construction and management (EPCM) companies for the preliminary design, because the slope conveyor will be considered part of the surface material handling processes. This preliminary design will be used when soliciting quotations for the slope conveyor. Unfortunately, EPCMs may not have enough expertise with conveyors to optimize the design. This expertise is available with an original equipment manufacture (OEM) of conveyors, which ultimately may be responsible for supplying the slope conveyor. Each OEM will provide a bid package that represents what it considers to be the optimal design.

Jan 1, 2013

By Irwin R. Higgins, Richard S. Dennis

Acid recovery employs ion exchange resin as an adsorption media for the separation of inorganic acids from mixtures of acids and their metallic salts. This technology has been used to treat spent pickling and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. Acid recovery can also be used for electrolyte treatment to facilitate valuable metal recovery and to improve product quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process strong acid concentrations. TETRA'S CCIX™ continuous I-X contactor has been used successfully in a simple, continuous operating mode to separate acid from its salt. Efficient separation is enhanced by refluxing which allows acid to be produced as a salt-free product at nearly its original strength. Continuous treatment also recovers heat to the bath and improves metal quality due to consistent acid quality.

Jan 1, 1995

By Bruce H. Mason

Lightweight aggregates are classified as those minerals, natural rock materials, rock-like products, and byproducts of manufacturing processes that are used as bulk fillers in lightweight structural concrete, concrete building blocks, precast structural units, road surfacing materials, plaster aggregates, and insulating fill. Other uses include architectural wall covers, suspended ceilings, soil conditioners, and other agricultural uses (Mason, 1989). One unusual agricultural use recently reported was for bedding on a crocodile farm on the south coast of Natal. It seems that female crocodiles became upset because there was no vermiculite in which to lay their eggs due to the late arrival of a consignment of vermiculite. The vermiculite was being used as a substitute for river sand to nest crocodile eggs (Griffiths, 1989). The various lightweight aggregate materials may be classified into four groups as follows: 1. Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials, such as pumice, scoria, tuff, breccia, and volcanic cinders. 2. Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing shale, clay, or slate in rotary kilns or on traveling grate sintering machines. 3. Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. This group of lightweight materials, with the exception of slag, has become less significant and will not be discussed in this chapter. Other lightweight aggregates are beginning to appear in the marketplace. Some are the result of manufacturing processes on industrial byproducts and/or waste products, such as fly ash and incinerator residue (Bigner, 1992). 4. Manufactured Insulating Ultralightweight Aggregates-pre- pared by pyroprocessing ground vermiculite, perlite, and diatomite. The application of diatomite in brick and in extruded and aggregate forms has declined in recent years (Kadey, 1983) and will not be considered in this chapter. Lightweight aggregates for structural concrete and concrete masonry units, according to the American Society for Testing and Materials (1986) consist of "aggregates of low density used to produce lightweight concrete, including: pumice, scoria, volcanic cinders, tuff and diatomite; expanded shale, clay, slate, perlite, vermiculite or slag; and end products of coal or coal combustion" (Mason, 1989). Lightweight aggregates are distinguished from other mineral aggregate materials by their lighter unit weights-1 281 to 1 602 kg/m3 or less for loosely packed lightweight aggregates-as com- pared to 2 002 kg/m3 or more for crushed stone, sand, gravel, air-cooled slag, and other common mineral aggregates. The specific gravities of these lightweight aggregates are also used to classify them for use in concrete; they range from the extremely light materials, used for insulative and non-structural concrete to expanded shale, clay, slate, and slags used for structural concrete. Vermiculite and perlite are sometimes referred to as super light- weights. Insulating concrete (non-load bearing) weighing as little as 240 kg/m3 can be made with these aggregates. Natural aggregates such as pumice, pumicite, and scoria are normally made into concrete weighing about 400 to 480 kg/m3. Expanded shale, clay, and slate produced in a rotary kiln make structural concrete ranging from 1 201 to 1 842 kg/m3. Expanded shale and clay produced by sintering make concrete that ranges from 1 442 to 1 922 kg/m3. Air-cooled slag produces concrete ranging from 2 162 to 2 403 kg/m3. The low density lightweight aggregates are used primarily for insulating purposes. They have relatively low compressive strength. The middle density aggregates are used for insulation and for fill. Those at the upper end develop excellent compressive strength and are used in many structural applications (Anon., 1971). In recent years, the production of lightweight aggregates in the United States for all uses (including insulation and construction materials) has averaged about 19 Mtpy (Table 1). The production and consumption of lightweight aggregate is closely tied to the fortunes of the construction industry and the need to construct energy efficient buildings. Recent years have seen the production of lightweight aggregate approach the levels of the early 1970s. The period of 1979 to 1981 was a low point in production levels. The low levels of production were caused by significantly higher plant energy costs due to the large amounts of fuel and energy used in the production of most types of lightweight aggregate. Lower levels of construction activity also affect production levels. This chapter focuses on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and on both the production and use of manufactured structural light- weight aggregates. Some additional comments are made on byproduct materials. Separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders are elsewhere in the volume. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials.

Jan 1, 1994

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

By Grover Wallace

At is important for today?s mining executives and leaders not to underestimate the fact that, while the recent downturn in the economy did take its toll on balance sheets and productivity, factors such as emerging countries, aging workforces, globalization and individual knowledge growth did not lay dormant while the economy was in a lull. It is key for mining leaders to be proactive in their talent strategies. Successful mining companies are developing a clear, concise and communicated strategy and placing a high priority on recruiting the right talent in global markets that parallels their business strategy. They are focused on placing the right people in the right jobs.

Jan 1, 2011

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the U.S. National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs) and manufacturers of filtration and pressurization systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3-89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent with the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality to equipment operators inside of enclosed cabs of mobile mining equipment, thus minimizing respirable dust exposure.

Jan 1, 2014

By L. S. Fountain

A national survey, 1978-1980, found 180,973 waste impoundments used by industrial mining, municipal and other interests. Possibly 27,000 contain hazardous materials. The potential hazard of leaks polluting water supplies is a growing concern. An electrical technique was developed to efficiently and speedily detect and locate leaks in geomembrane-lined liquid impoundments without emptying the contents. A potential applied between the liquid and earth causes electric current to flow through leaks in the insulating geomembrane material to ground. The cur- rent density around the leak is used to detect and locate the leak. Field tests show single and multiple leaks 2.54 cm in diameter or less can be detected and located to within less than 30 cm.

Jan 1, 1986

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By David Dvorkin, Thomas C. Anderson

INTRODUCTION A major function of the Mine Safety and Health Administration (MSHA), Denver Safety and Health Technology Center (DSHTC), Ventilation Branch, is to provide engineering analyses of underground mine¬ ventilation systems for coal, metal, and nonmetal in¬spection departments in accordance with field surveys and data analyses. Health and safety problems such as the control of diesel contaminants, dust, methane, radon, and radon daughters all are dependent upon ventilation. It is necessary for the ventilation engineers at DSHTC to have a complete understanding of the various and highly complex ventilation systems used in the nation's mines. Only through the proper assembly and analysis of data can the engineer determine the causes of prob¬lems and make suitable recommendations. Furthermore, the engineer must have the ability to predict the results of any such recommendations. In the study of the ventilation system at any indi¬vidual mine, it is common practice to collect data on airflow quantities and pressures at key points throughout the mine. However, these data give only a single point¬-in-time view of the system. As the mine develops and progresses, the system undergoes numerous changes; as the mine becomes more extensive, the ventilation re¬quirements increase, and the costs rise. For proper utilization of the available resources, it is necessary for the engineer to have a sound engineering basis for deci¬sions on how best to ventilate the mine. To evaluate the system as a whole, particularly re¬garding possible system changes, it has become necessary to rely on computers to perform the calculations in¬volved in analyzing the network. This chapter sum¬marizes the implementation of such computer capabili¬ties at DSHTC, as well as the services that are available from DSHTC. ANALOG SIMULATIONS AND ANALYSES OF VENTILATION NETWORKS As early as 1954, the US Bureau of Mines (USBM) in Pittsburgh, PA, was using an analog computer as an aid in analyzing ventilation systems. The Mcllroy Fluid Network Analyzer used filament-tube resistance elements and an electrical power supply to simulate mine-ventila¬tion systems electrically. This system is shown in Fig. 1. Analog simulation has proven to be a practical tool, providing fast analyses of complicated problems after the initial setup has been completed. Advancements in electronic technology over the past 24 years have made possible the construction of an analog computer that has streamlined several operating features of the previous machines. The DSHTC Ventilation Branch now has an improved electronic analog computer to assist in the analyses of ventilation systems. General Features As shown in Fig. 2, the analog computer used at the DSHTC Ventilation Branch has three "element" cabi¬ nets, a console, and a printer. The cabinets contain the fan elements and the airway-resistance elements that are used to "program" an analysis problem; each element is independent of the others. The console contains the "patchboard" and the controls necessary to operate the analog computer. The patchboard connects the inde¬pendent elements into the circuit appropriate for simu¬lating the ventilation system. The total system is controlled from a panel on the console, while the value corresponding to each element is set on the individual controls located on the face of each element. The control panel has three visual output displays that give the quantity of flow, the pressure of the output junction with respect to a datum, and the differential pressure across each element. The control panel also allows manual selection of the element to be monitored, or automatic scanning and printing of values for the entire system. Capabilities The analog computer can simulate an existing mine¬-ventilation network. This is accomplished by collecting field data at the mine to give a complete pressure-¬quantity network. Resistance values for each airway branch may be determined from the quantity of flow in the branch and from the pressure differential between the end-point junctions of the branch. The basic rela¬tonship to determine the resistance is expressed as: H=R •Q2 where H is the pressure differential, R is the resistance, and Q is the quantity of air in the flow. After the resistance values are known for all of the airways in the circuit, the elements on the analog com¬puter can be set to the corresponding values. The elements are designed to reflect the basic relationships, with electrical potentials corresponding to pressures and

Jan 1, 1982

By R. V. Ramani, K. V. Raj

"The air flow problems in open pit mines are complex. Computational fluid dynamics (CFD) models provide a detailed knowledge of the airflow pattern and velocity distribution, temperature, and pollutant concentration within an enclosed domain of the open pit. A range of turbulent model can be selected for varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithm they use; as a result, prediction varies from model to model. This paper presents a study of pollutant transport in an actual open pit mine under stable boundary layer. The objective is mainly to test two turbulence models using the same input conditions, model constants, and similar geometry. Measured data are used to compare results of the two CFD models, namely, the kappa-epsilon (?-e) model and the Large Eddy Simulation (LES) model. Despite the complex synoptic situations, different meteorological input data and the fast changing conditions, the simulation results from both the models are in good agreement regarding the dispersion of pollutants.INTRODUCTION Modeling of contaminant transport under Arctic air inversion is an important step for an assessment of the amount of pollutants within the open pit. The Airflow in open pit mines is of larger scale and does not follow the principles of pipe flow. The air flow problems in actual open pit mines are thus far more complex. CFD models provide a detailed knowledge of the airflow pattern and air velocity distribution, temperature, and pollutant concentration within an enclosed domain of an open pit. There is no known application of CFD in three-dimensional modeling of air flow in large open pit mines. Two equation RANS kappa-epsilon (?-e) and Large Eddy Simulation (CFD) models, however, have been developed to solve the stable boundary layer (SBL) problems in Atmospheric Sciences (Baklanov 2000, Basu and Porté-Agel 2006, Dop and Axelsen 2007, Bandopadhyay et al. 2014). Because an exact flow situation in open pit mines is not known a-priori, it is therefore, necessary to investigate various turbulent models to identify the appropriate model that would simulate the flow phenomena with reasonable accuracy, and predict the contaminant distributions within the pit. Dispersion models differ in their assumptions and structures as well as in the algorithm they use and, as a result, predictions vary from model to model. Furthermore, it is also important to investigate the behavior of a CFD model in simulating a complex phenomenon such as the transport and distribution of contaminants in open pit mine under Arctic air inversion. The simulation of an enhanced period of turbulence in SBL is of particular interest because traditional air pollution dispersion models cannot explicitly treat such intermittent events, and yet the SBL is often the worst-case scenario in an open pit pollution transport"

Jan 1, 2015

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure, and other types of sensors are increasingly being used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP) while older forms of serial communication are being retired. This paper presents the selection, configuration, and testing methodologies that were employed by researchers from the National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide Internet Protocol data transport. INTRODUCTION To enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry [1]. However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology (IT) infrastructure in place to handle the data transport requirements for the newer IP-based technologies that are part of IIoT. This was the case with a mine in the Western United States; it lacked the infrastructure to perform critical monitoring in remote headings. The mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH’s) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder system to achieve IP data transport using commercially available land mobile data radios. DATA RADIO SELECTION The primary selection criteria for the data radios were network data format, modulation type, and radio channel spacing. The network data format decided upon was Internet Protocol. This format allowed for straightforward integration between the IP-enabled data acquisition system located in a remote heading and the network switch located in the control room. It also eliminated the added complexity of additional network hardware such as Ethernet to Serial converters. IP additionally provided a direct path to integration into higher bandwidth networks, such as fiber optic, should they become available."

Jan 1, 2018

By L. S. Gourevitch, E. B. Kremer, A. Y. Fidlin, Y. M. Katsman, I. I. Blekhman

A new kinetic approach to simulation of fracture is given. The main object of the simulation is forecasting transformation of ore lumps size distribution in squeezing of ore layer between two planes. The approach rests on fundamental principles of energy and mass conservation and on new ideas about fracture physics connected with fractal geometry. On this base an integro-differen tial equation of layer crushing kinetics is formulated. This equation is similar to well-known kinetic equation of grinding, but here we use elastic energy density in place of time as an independent variable while selection function is considered by us to be dependent on this variable. Properties of the equation have been investigated by us and its analytical solution has been found. It allows to compute simultaneously both the evolution of the size distribution process of squeezing and force-displacement diagram. Results of theoretical calculations provide a good fit with experimental data.

Jan 1, 1995

By Chee Theng

"It is not surprising that the most popular key takeaway from the Developing Diversity in Mining workshop (see box) held on the first day of the SME Arizona Conference in December was, “Have more parties!”The adage that mining professionals work hard and play hard was clearly demonstrated at the two-day conference in the JW Marriott Tucson Starr Pass Resort & Spa in Tucson, AZ. Nearly 550 participants, some of whom had left behind frigid temperatures and thick parkas in their hometowns, attended a full slate of technical sessions, shared industry experiences and knowledge, reconnected with buddies in the industry, and made strategic new contacts in the conference’s collegial environment, aided by the mild Arizona winter.To start off the technical sessions, John Mansanti, president and chief executive officer of Crystal Peak Minerals and 2017 SME president, entertained a packed lecture room with his keynote lecture on “Tariffs, Embargos, and Cartels ... Oh My! A Perspective on Potash.” Mansanti gave the audience the benefit of his more than 35 years of experience at companies including Barrick Gold, Newmont Mining Corp., Placer Dome, Freeport-McMoRan and Intrepid Potash, where he was senior vice president for operations, technology and strategy. At the luncheon, Justin Cross, general manager of Freeport-Mc- MoRan’s Bagdad operations, spoke on how the role of a leader in mining is transforming from one based on technical expertise to one based on the ability to collaborate, to lead and to adapt to changes in technologies and skill sets, in his talk on “Knowing When to Learn, When to Lead and When to Manage.”"

Feb 1, 2019

Just 104 km (65 miles) from Phoenix, AZ, Rio Tinto hopes its new Resolution Copper Mine will be a showcase for the Rio Tinto management philosophy. Its goal is to have a net positive impact. In every place that Rio Tinto mines, it wants to be able to have an overall beneficial effect on the local community, environment and economy. ?We?re constantly working to understand our impacts, to understand how to minimize our impacts and understand how to mitigate those impacts,? said Resolution Copper Mining chief executive officer David Salisbury, from the global headquarters of Rio Tinto Minerals in Green-wood Village, CO.

Jan 1, 2010

By Pedro Pablo Vasquez Coronado, Victor Octavio Tenorio

"Productivity in openpit mines depends on the observation and adjustment of critical phases of operation. As one of the most expensive activities in openpit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad hoc methodology for analyzing the key performance indicators (KPIs) involved in the production cycle, it is possible to compare actual performance and ideal operating conditions and develop an alert system when operating conditions are subpar with the expected production standards.Study objectivesThe purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle, or when the time of completing production tasks is falling outside a predefined value. This alert is compared with predefined KPIs and is used to determine corrective actions.The alert will:• Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process.• Demonstrate the utility of KPIs in the extraction of ore and waste and how they help to identify equipment performance.• Develop software interfaces to visualize the alert system in order to increase awareness in the operations supervisor.• Make recommendations for future applications that can help improve the productive process of an openpit mine.Problem statementTransporting material in openpit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity while subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded and other delays. This creates inefficiencies in fuel consumption and energy utilization.For the identification of delays, a contextbased system could be required in order to help optimize the haulage cycle time by controlling delays in loading, haulage and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2015