Search Documents

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By J. W. Jamieson, J. Escartin, A. Steinführer

Evidence of hydrothermal activity on two Mid-Atlantic Ridge oceanic core complexes (OCCs), at 13º30’N (the Semyenov 1 through 5 fields) and 13º20’N (the Irinovskoe field) (Fig. 1) were studied using CTD casts, dredges, TV-grabs and SP surveys during previous research cruises to these sites (Cherkashev et al., 2013, McLeod et al., 2009). In late 2013, the Semyenov and Irinovskoe fields were revisited, this time with an autonomous underwater vehicle (AUV) and a remotely-operated vehicle (ROV) during the ODEMAR (Oceanic Detachments at the Mid-Atlantic Ridge) cruise on the French research vessel "Pourqoui Pas ?". Here we present the first visual surveys and direct sampling of these vent sites. High-resolution (~2 m) bathymetry of the 13º30’N and 13º20’N OCCs and their associated vent fields was collected during 4 and 5 AUV dives, respectively, using the GEOMAR AUV "ABYSS" (Fig. 1). These surveys were flown between 70 m and 100 m above the seafloor, typically at a constant height to reduce vehicle movement. The AUV was equipped with Eh, turbidity, and temperature sensors in order to detect active hydrothermal venting. Over twenty ROV dives with the ROV "VICTOR 6000" allowed for the visual exploration of the OCCs and collection of 59 hydrothermal rock samples from the vent fields. As a result of these exploration activities, the first robust estimates of the size of the deposits, and the geologic controls on sulfide accumulation at these sites can be determined.

Sep 1, 2014

By Christopher J. Bise

INTRODUCTION A mine's power system represents the driving force behind all of the extraction and auxiliary operations, because the production and transportation of mined material and the operation of equipment, such as fans and pumps, are all dependent upon a power source. Once, compressed air was the primary power source in mining; today, however, electrical power dominates. This chapter reviews the basic theories of com- pressed-air and electrical power and provides several examples of applications in mine power systems. COMPRESSED-AIR POWER General Compressed air has been, and should continue to be, an important source of power in mining operations. It has been used as a means of blasting coal in conventional mining and is widely used to operate stopers, mucking machines, and other air tools in both coal and hard-rock mines. Such applications demonstrate the suitability of compressed air for applications requiring linear motion, but it is also utilized for its reliability and safety. A compressed-air system is composed of a compressor, a receiver, a distribution network, and the air-operated machines. A compressor takes in air at normal atmospheric pressure (free air) and compresses it to a higher discharge pressure. The discharge pressure must be high enough to overcome the friction in the distribution system of pipes and hoses and deliver the compressed air to the machines at the pressure recommended by the manufacturer. The most common type of compressor used in mines is the reciprocating compressor in which the air is compressed by a piston in a cylinder. An air receiver is a container or storage tank that is located in the distribution system between the compressor and the machines. It stores compressed air, when the full capacity of the compressor is not being used, and gives a more steady flow of air to the machines. The distribution network consists of pipes, Oalves, elbows, tees, and hoses that transmit the compressed air from the receiver to the machines in the mine. It is essential that the distribution system be designed with the proper sizes and lengths of pipe, hose, and other components to keep pressure losses well within allowable limits. The air-operated machines consist primarily of drifters, stopers, pluggers (sinkers), slushers, and several other pieces of equipment. Compressor Operation Every compressor is made up of one or more basic elements; a single element, or a group of elements in parallel, comprises a single-stage compressor. Many compression problems involve conditions beyond the practical capability of a single compression stage. Too great a compression ratio (absolute discharge pressure divided by absolute intake pressure) may cause excessive discharge temperatures or other design problems. It, therefore, may become necessary to combine elements or groups of elements in series to form a multi- stage unit, in which there will be two or more steps of compression. The number of stages commonly used in reciprocating compressors is as follows: Pressure Number of stages 0- 150 pig 1 80- 500 psig 2 500-2500 psig 3 2500-5000 psig 4 When pressure is referred to as pounds per square inch gage (psig), it means the pressure (in pounds per square inch) above barometric pressure as measured by a gage. The sum of barometric pressure and gage pressure is the absolute pressure (in pounds per square inch). The gas is frequently cooled between stages to reduce the temperature and volume entering the subsequent stages, thereby reducing the work required for compression. The basic reciprocating compression element is a single cylinder compressing on only one side of the piston (single-acting). A unit compressing on both sides of the piston (double-acting) consists of two basic single-acting elements operating in parallel in one casing. The reciprocating compressor uses automatic spring-loaded valves that open only when the proper differential pressure exists across the valves. Intake valves open when the pressure in the cylinder is slightly below the intake pressure. Discharge valves open when the pressure in the cylinder is slightly above the discharge pressure. In Fig. 1, Diagram A shows the basic element with the cylinder filled with air at atmospheric pressure. On the corresponding theoretical pressure-volume

Jan 1, 1986

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

The Canadian mining industry is one of the strongest in the world. Not only does the country produce a sizable amount of minerals and metals, Canada plays host to hundreds of global mining companies, large and small. The country, for the most part, recognizes the importance of natural resource development, particularly mining, to its economic well being. Like any country, though, there are federal and provincial regulations on the books that the industry takes issue with. But there are also certain economic incentive programs in place to encourage exploration and mine investment. And, unlike the industry and the United States government, the Canadian government and mining industry appear to have a reasonable working relationship.

Jan 4, 2010

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007

By Maurício Covcevich Bagatini, Maycon Athayde

Nowadays, the HPGR (high-pressure grinding rolls) is an intermediate step between filtering and balling in the most modern iron ore pelletizing operation. The operation debottlenecks filtering process and reduces pressure over the typical milling process to control particle size to the balling. The present study evaluated aspects of microwave application to the iron ore concentrate fed to HPGR in a bench scale unit. Iron ore concentrate was irradiated varying the microwave exposure time and grinding efficiency was evaluated. The moisture influence in the HPGR efficiency was also assessed. The pellet feed blaine surface area (BSA) improved by 300 cm2/g and % < 325# fraction by 3%. Scanning electron microscope (SEM) images show the formation of micro-cracks onto the particle surface induced by microwave; the effect observed helped improve the milling process performance, in addition to the moisture reduction observed due to the temperature increase.

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By Steve Kral

More than 124,000 people involved in the mining and construction industries throughout the world poured into Las Vegas, NV in March for ConExpo-Con/Agg ’99. Show organizers said this triennial exhibition is the largest equipment show in the Western Hemisphere and one of the largest exhibition of any industry. “Clearly, Con-Expo-Con/Agg ’99 was one of the largest trade shows of any industry ever held in the Western Hemisphere,” said Bruno Benna, co-chair of the event. Attendees included mining industry representatives, including aggregates, and sand and gravel producers. In addition, many of the attendees work in the construction, reclamation, forestry, asphalt paving, landscaping and concrete industries. According to show records, about 52% of those attending were company presidents, vice presidents, chief financial officers or managers.

Jan 1, 1999

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By Lawrence M. Zanko

Eighteen coarse taconite tailings samples were collected in 2000-2001 from five western Mesabi Range taconite (iron ore) operations located in northern Minnesota, i.e., EVTAC, Hibbing Taconite (Hibtac), USX Minntac, Ispat Inland (Minorca), and National Steel Pellet Company (NSPC), to test their physical, geological, chemical, and mineralogical properties [Zanko, L.M., Niles, H.B., Oreskovich, J.A., 2003. Properties and aggregate potential of coarse taconite tailings from five Minnesota taconite operations, Minnesota Department of Transportation, Local Road Research Board, St. Paul, MN, Report No. 2004-06 (also as Natural Resources Research Institute technical report, NRRI/TR-2003/44)]. The goal was to assemble a body of technical data that could be used to better assess the potential of using a crushed taconite mining byproduct like coarse tailings for more widespread construction aggregate purposes, primarily in roads and high¬ways. An important part of the mineralogical assessment included X-ray diffraction (XRD) analyses and microscopic (polarized light microscopy, scanning electron microscopy, and transmission electron microscopy, i.e., PLM, SEM, and TEM, respectively) evaluation of the size and shape (morphological) characteristics of potentially respirable microscopic mineral particles and fragments. Quantitative mineralogy, based on XRD analyses, showed that the dominant mineral in all samples was quartz (55-60%), followed by much smaller amounts of iron oxides, carbonates, and silicates. Specialized microscopic analyses and testing performed by the RJ Lee Group, Monroeville, PA, on both pulverized (-200 mesh, or 0.075 mm) and as-is sample composites showed that no regulated asbestos minerals or amphibole minerals were detected in the western Mesabi Range samples. A small number (26) of non-asbestos and non¬amphibole mineral cleavage fragments/mineral fibers were detected by SEM out of 1000 fields analyzed, but most were identified as min¬nesotaite and talc, silicate minerals common to the Biwabik Iron Formation. Amphibole minerals, absent in coarse tailings samples from the five western Mesabi Range taconite operations, were present in a single eastern Biwabik Iron Formation sample collected in 2003 for Lake County from the Cliffs Northshore operation in Silver Bay, MN. Importantly, the Superfund Method for the Determination of Releasable Asbestos in Soils and Bulk Materials [United States Environ¬mental Protection Agency (USEPA), 1997. Superfund method for the determination of releasable asbestos in soils and bulk materials, EPA 540-R-97-028, U.S. Environmental Protection Agency, Washington], as modified by Berman and Kolk [Berman, D.W., Kolk, A.J., 2000. Modified elutriator method for the determination of asbestos in soils and bulk materials, Revision 1: Submitted to the U.S. Envi¬ronmental Protection Agency, Region 8, May 23, 2000] failed to generate any protocol fibers, i.e., fibers longer than 5 µm and thinner than 0.5 µm, from either the western coarse tailings samples or the single eastern Biwabik Iron Formation sample. The combined findings suggest coarse tailings and other taconite mining byproducts should be treated with the same common sense safety and industrial hygiene approach practiced for all mineral-based materials that have the potential to generate respirable dust. © 2007 Elsevier Inc. All rights reserved.

Jan 1, 2007

By Franklin J. Stermole

L. Alan Weakly, member SME, is a senior staff engineer, Exxon Co. Weakly chaired a Mining Engineering committee formed to solicit materials for six planned "personal skills" articles, to be used in ME this year. What follows are Weakly&apos;s introductory comments to the series. Upon graduation from college several years ago, I thought that I was sufficiently prepared to embark in my chosen profession. A short time later I realized that several years of on-the-job training was going to be required before I could use my technical training effectively. It never occurred to me that, professionally, I was seriously lacking in any other skills. My spelling could use a little upgrading, but this was not a serious deficiency. I have been very fortunate to have had two employers that recognized that their engineering professionals did lack other skills and made every effort to give them training to correct these deficiencies. The skills I am referring to are those in administration and interpersonal relationships. Most mining engineers and geologists receive very little, if any, college training in these areas. In addition, many companies do not provide this training and many mining engineers and geologists are unaware of their deficiencies. It is for this reason the subject of personal skills development is being introduced in Mining Engineering. The mining engineer or geologist can pursue one of two basic career directions, managerial or technical. In today&apos;s technically sophisticated society and highly competitive business climate, both orientations require administrative and interpersonal skills. Most of us are technically qualified and we continue to upgrade our technical skills. But many studies indicate that we, as a group, are significantly weaker in administrative and interpersonal skills than other professional groups. In addition, these studies indicate that engineers, in general, take longer to reach managerial levels and fewer do so. This series in Mining Engineering, then, should help readers strengthen and broaden their professional capabilities. In all industries, including mining and petroleum, economic analysis of potential investment projects is done to select the projects that will give maximum future value from the investment of available capital. Rather than looking directly at the future values to be generated by investing capital in alternate ways for economic decisions, evaluators usually use either rate of return, present value, annual value, a profit to investment ratio, or various break even analysis results to reach economic analysis decisions in evaluating alternative investments. Alternative economic evaluation techniques are used in industry to properly analyze the economic potential of various investment projects. "Discounted Cash Flow" analysis is the phrase commonly used to describe these techniques. Whether you want to analyze projects in mineral, petroleum, real estate, refining, pipe-line transportation, or any other industry, proper application of discounted cash flow analysis techniques enables you to fairly compare the economic potential of alternative projects as well or better than you can using any other project evaluation approaches. It should be pointed out that investment analysis generally involves more than economic analysis. Financial and intangible considerations sometimes are as important or more important to investment decision-making than economic considerations. Economic analysis refers to evaluation of the profit generating potential of projects, that is selecting which alternative projects will generate maximum future value possible from available investment capital. Financial analysis, on the other hand, relates to analysis of where money is going to come from to finance various projects. Regardless of the economic potential of a project, if financial analysis indicates that we cannot finance the project, it likely will be shelved for financial reasons even though it may be economically satisfactory. Many evaluators use the terms "economic analysis" and "financial analysis" interchangeably, but this author considers that to be undesirable. Intangible analysis relates to project factors that are difficult to quantify in

Jan 2, 1984

By N. Merriam

This report describes Koppelman&apos;s work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997