Search Documents

By B. R. Pothini, H. von Schonfeldt

In underground coal mining many excavated openings have a relatively short projected life span. To ensure safety for men and materials at a minimum cost over the projected operating life, only pillars for overburden support and roof bolts for support of the openings are used extensively. Mining activity constantly changes the geometry of the mine producing load changes on the structural support members of the openings that often induce unstable deformations which can lead to roof falls or pillar failures. The paper describes how simple deformation measurements can be used to design primary and supplementary roof supports and to predict roof falls and possibly pillar bumps. Specifically, bed separations in the roof measured directly with the help of borescopes and calculated from differential convergence data are used to optimize bolt links or support requirements for chemical stabilization of mine roofs. Roof falls are predicted on the basis of admissible values for cumulative convergence between roof and floor, convergence rate, and the change of the rate of convergence. The pillar extraction operations convergence anomalies detected from contouring identify bump prone pillars, while convergence and pillar dilation determine the yield zone in a pillar to verify pillar softening and de-stressing. Manuscript not received in time for publication.

Jan 1, 1983

By Armin C. Supp

Since 1975, about a dozen high capacity flotation plants have been installed in the Ruhr district. Depending on the size of the preparation plants, the design capacity of the flotation section is between 100 - 150 t/h. The flotation units generally comprise rougher and cleaner stages in which 5 to 6 or 4 to 5 agitators respectively are arranged in line. The unit volume allocated to each agitator is up to 16 m3. The type of flotation machines, the design of these plants and their instrumen¬tation and control equipment are described in detail. The run of mine coal in the Ruhr district is characterized by a wide variety of the volatile matter. Generally, a distinction must be made between coals with more than 30 - 35% V.M., which are preferably used in power station, and coal with lower V.M. content, which are preferably used as coke-oven feed. The difference between these coals in respect to grain-size distribution, ash cotent and flotation properties will also be described in detail.

Jan 1, 1985

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By Mike Preston

Attrition scrubbers may not be glamorous, but they are an important and sometimes neglected step in mineral processing. Optimal attritioning will significantly improve the results and efficiencies of subsequent processing steps and can lead to reduced costs and improved product yields. Why is attrition scrubbing used? Attrition means to wear away a surface, typically by friction or abrasion. An attrition scrubber does exactly this, using impellers to force particles against each other, causing intense scrubbing, grinding, abrasion and polishing. This process is not a new concept. It has long been used in the glass industry to remove surface contaminants from silica. But it is also widely used in many areas of mineral processing and other applications including soil remediation and plastics recycling. In mineral separation, for example, the scrubbers help improve yield and efficiencies by preparing feed materials for downstream processes such as flotation, magnetic or electrostatic separation. Inefficient scrubbing can lead to coatings remaining on valuable minerals and decreased yields, as the covered minerals cannot be processed efficiently or are mistaken as waste contaminates and removed. In the example of flotation separation, pre-flotation conditioning uses attrition scrubbers to provide better recovery of minerals while using fewer chemicals. If surface contaminants remain on the mineral, yield is reduced, as the unwanted coating acts as a barrier to the reactants, which make it unfloatable and, therefore, unrecoverable.

Oct 1, 2013

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

This review provides a new and comprehensive summary on studying colloidal interactions encountered in mineral processing with representative examples for critical information, which are of great scientific and practical importance. Colloidal interactions play a vital role in mineral processing, including grinding, physical separation (particularly flotation), dewatering and tailings management (Fig. 1). Despite great energy input in comminution to liberate valuables from gangues, hetero-coagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. The importance of colloidal interactions is becoming increasingly significant as we process ever more finely disseminated low-grade ores as a result of inevitable depletion of high-grade ore deposits. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. 

Heap leaching has become one of the prime technologies used for the recovery of precious metals from low-grade ores over the past ten years. The recovery process involves mining and stacking the ore on engineered leach pads, with or without crushing and/or agglomeration, followed by leaching with a low concentration sodium cyanide solution. The metal-bearing, pregnant solution is then processed by zinc precipitation or activated carbon absorption to extract the precious metals. The leaching process continues until all economic metal values are removed at which time the spent heap leach pads, the leached materials and excess process solutions require decommissioning. The management of these solutions may present a potential challenge for successful and environmentally sound decommissioning due to their composition, volume or continuity of generation from the spent ore even though active leaching has been terminated. The principal objectives of solution management in decommissioning spent heap leach pads are to meet all operative environmental regulations in a cost-effective manner and to leave the pads in a condition where they do not present a long-term liability either to the operator or to the environment. This involves the reduction in volume of the residual process solutions and/or treatment of these solutions to where they meet applicable water quality criteria. In the past, the environmental and economic aspects of decommissioning and solution management have been overlooked or under-estimated during the planning of mining operations. As a result, there is a potential for long-term liabilities and costs to be recognized only at the end of active leaching, a time at which operating revenues and cash-flow are minimal. Therefore, the decommissioning process requires addressing at the mine planning stage and agencies now require that a plan for solution management after the cessation of operations be submitted prior to initiation of mining. This paper discusses aspects of process solution management during decommissioning, both in terms of quantity and quality, and how potential issues may be recognized and planned for in the initial stages of heap leach design.

Jan 1, 1992

By L. V. Wade

The use of longwall/shortwall mining systems is under increasing scrutiny by the U. S, coal industry as a means to reverse the decline in productivity. The success of these mining systems depends to a great extent upon designing the system hardware to best suit local conditions. Of particular importance in this regard is designing the various elements of the total ground support system, including face, face end, and gate road supports, to accommodate local geologic conditions. This presentation centers on the problem of selecting the face support system. The existing geologic situation can influence the selection of the face support hardware in a variety' of ways. In general terms, these influences can be grouped into the following four areas: 1. The capacities required of the support unit; 2. The roof, coverage supplied by the support units; 3. The flexibility required of the support unit to meet changing geologic conditions; and 4. The required stiffness characteristics of the individual support units both vertically and horizontally. The following will center on the first area, i.e., the required d capacities of the support unit, in particular, the maximum required load density for a particular geologic situation.

Jan 1, 1976

By R. L. Loofbourow

SEVERAL categories of storage are used depending on capacity. Operational storage, which is small in comparison with the market, facilitates handling surges of a few hours' or a few days' duration. Seasonal storage, usually larger, permits accumulation of product during sea- sons when demand is low, for delivery when demand is high. In producing areas, large storage may permit production at a uniform rate, without waste or distress sale. Near large markets such storage increases the efficiency of transportation, allows a more extensive or higher grade market to be served, and affords protection against interruption in delivery.

Jan 1, 1959

By J. E. Urosek

The Mine safety and Health Administration (MSHA) formed the Mine Ventilation Bleeder and Gob Training Committee in 1993. This committee was charged with developing a training course designed to enhance the knowledge and understanding of practical bleeder ventilation systems. The course will probably include a discussion on the theory behind bleeder system design, an in-depth look at the strengths and weaknesses of the basic bleeder system types, case studies, and a review of the systems currently in use. A database on active underground bituminous coal mines, gob areas, and the bleeder systems presently used was developed from questionnaires distributed to nine Coal Mine Safety and Health (CMS&H) districts. Representative systems were selected for thorough investigation to develop case studies. This paper introduces some of the material to be included in the course, including a description of basic bleeder system designs, a review of a portion of the database, and facts about the gob areas and bleeder systems investigated for the development of case studies.

Jan 1, 1995

By Rodrigo Jerez

This paper describes a Mixed Integer Linear Programming model that was developed for planning the coal operations at Mountain Coals, Inc., in Kentucky. The model incorporates the use of stockpiles as practiced and allows the operator to find the least cost combination of raw coal feeds, washing densities and blending to produce the different quality coals as required by the coal contracts.

Jan 1, 1984

By J. A. Bleeck

A discourse on the relationship between industrial minerals and paper production, concentrating on high grade, ultra fine ground calcium carbonate (mean particle size less than 2 microns) and precipitated calcium carbonate. The scope of the paper encompasses four basic areas relevant to the topic: 1. A tutorial overview of the papermaking process with an examination of various industrial mineral components in that process; 2. A discussion of basic technological topics pertinent to the utilization of carbonate in paper with emphasis on the relative aspect. Of natural ground calcium carbonate (GCC) and synthetic precipitated calcium carbonate (PCC); 3. An overview of paper and carbonate market, in both the United State, and Europe with emphasis on (a) current status and future growth trend. Of such market., and (b) discussion of the major influences on growth and development of such market.; and 4. Identification and discussion regarding the principal producers in calcium carbonate markets serving the paper indu.try in Europe and North America.

Jan 1, 1993

By John R. Marks

Introduction An engineer is a builder and a problem solver. He uses knowledge of the properties of matter and energy to furnish the needs of society. Engineers form the bridge between scientific researchers and the general public, most of whom are technologically illiterate. Mining, metallurgical, and petroleum engineers extract minerals from the ground and process them into usable forms. Then, other engineers further process them into society's needs. Minerals engineers deal with more uncertainty than other engineers. Each ore deposit has its own personality and each ore is metallurgically unique. Minerals engineers, therefore, must be flexible, often applying larger safety factors and contingencies than other engineers, and frequently functioning as a jack of all trades. A minerals engineer can work in coal, oil, oil shale, base metals, ferrous metals, precious metals, industrial minerals, strategic minerals, or in exploration. Other mining jobs include banking and financing, education and research, marketing and sales, and government. As a minerals engineer, you may be among the first to work on the ocean floor or the moon. College Preparation A difference between college and industry is the type of problems to be solved. A typical college problem has an exact answer derived from given information. An industry problem is more apt to have a solution chosen from a number of alternatives. Information required for the solution is not given. It must be measured, calculated, looked-up, estimated, or otherwise derived. Solutions involve trade-offs, economics, and human factors, as well as application of physical laws and theory. When a college problem is answered, you move on to the next one. In industry, however, the headaches may just be starting with the implementation of the solution. Students often complain that they see little use for the theory they are learning. This is valid. A good professor will link theory and practice. Another difference between college and industry is the price of failure. In college, you can make a half-hearted effort in an assignment and take your C or D. On the job, however, poor engineering results in potentially effective projects being rejected and unsound projects being undertaken. Poor performance results in cost overruns, schedule holdups, oversights, disgruntled employees, irate bosses, unsafe structures, and unreliable systems. The costs are time, money, and possibly lives. The student pays the university for his work - not the other way around. So the rewards for good schoolwork often seem nebulous. But education must be viewed as an investment. Working for good grades will help you think better, learn more, receive better job offers, and perform more effectively on the job. There is no substitute for hard work. Avoid taking the easiest electives. If you desire a more liberal education or dislike rigorous physical sciences, mathematics, or engineering courses, change majors. Remember, you are training to be an engineer, not a computer programmer or market analyst. At least one summer of industry employment is necessary for minerals engineering students. The sooner you gain actual experience, the sooner you will know whether to change majors. Most large companies hire students during summer. It is best to send out applications around Christmas break. First and second year students usually work as laborers. Upper-classmen may work as engineering technicians. Students must sometimes choose between returning to a company at a higher position or trying a different company at a lower position, for more varied experience. Both alternatives have advantages. Do your best on these summer jobs. The company is watching. If you do well, the chances are good you will get a job offer when you graduate. Good references are important when you begin job hunting. Interviewing occurs near the end of your school career. The standard procedure is to send your resume with a cover letter to each company you are interested in. The resume for a graduating engineer with little experience need not exceed one page. The cover letter must be written for the individual company.

Jan 2, 1985

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By AK Raina

Blasting is used in mining and civil excavations to break the rockmass for ore production or creation of space. One of the disadvantages of the method is that it causes breakage beyond the proposed excavation lines. Pre-split is used to control such breakage in rockmass. This paper introduces the use of digital image analysis technique (DIAT) to measure rock breakage and half cast factor (HCF%). A new factor, undamaged area (AUD%), is introduced to improve the prediction, owing to the shortcomings of the HCF%. A comparison of significant data of AUD% and HCF% showed that HCF% has a lacuna of overpredicting, whereas AUD% can be used effectively to address the issue. Artificial neural networks are used to solve the complexity of multiple variables involved in predictions and to ascertain the importance and sensitivity of such variables in prediction regimes. This method will help users to evolve blast-induced damage objectively. A comprehensive scheme of things for future developments is included, which can be helpful to researchers in defining their research in this area.

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By Jey K. Jeyapalan

A characteristic common to most tailings dam failures caused by earthquakes or excessive rain storm is that the tailings tend to liquefy and flow for substantial distances as a viscous fluid, with the potential for extensive damage to property and life. Failures of El Cobre, Chile (1965), Mochikoshi, Japan (1978), Aberfan, Wales (19661, Buffalo Creek, West Virginia (1972) are examples of such catastrophic incidents. In these four incidents more than 400 lives were lost, and the loss of property was approximately $200 million. In order to be able to assess the potential for damage in case of such a failure, it is necessary to predict the possible extent of flow slide movement. This paper discusses simple procedures for performing such analyses. Also, in order to illustrate the use of these analysis procedures in tailings dam design, two case histories are analyzed.

Jan 1, 1982

By W. Burger

For the development of deep, hard rock, mines fast access to the orebody is critical. In some cases the mineralized area is more than 1,500 m (5,000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill-and-blast operations. In hard rock conditions, roadheaders cannot be used effectively, so disc cutting is the first choice. For excavation of declines, tunnel boring machines (TBM) can be used in many cases. These provide, in certain rock conditions, considerably higher production rates com-pared to drill-and-blast excavation. Herrenknecht AG has developed a vertical shaft sinking machine (VSM) that is able to excavate shallow shafts in soil and medium soft rock. The ground is excavated by a roadheader boom. The muck is removed by a slurry system or a pneumatic system in combination with hoisting of skips. These machines have been applied successfully on shafts down to 100 m (300 ft). A pre-sink for a deep mine shaft has been excavated by this technology. For deep, hard rock shafts, a new shaft boring system has been developed by Herrenknecht AG in collaboration with Rio Tinto. Based on proven technologies, the system uses a unique arrangement of existing proven technologies. The system integrates excavation, mucking, primary rock support, installation of the final lining and shaft infrastructure. This new system improves the health and safety of shaft construction. Detailed performance estimates indicate significantly higher shaft construction rates are possible compared to conventional shaft sinking methods.

Jun 1, 2010

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963