Search Documents

In some 35 years in the explosive and construction industries, we have probably seen the extremes in drilling and blasting practices. All of you know that it is difficult if not impossible, to separate those two operations, particularly when we are searching for an optimum. Early in my career while doing engineering survey work for a major cross country pipeline construction company, we witnessed some of the wildest blasts imaginable, and they were wild for two reasons. Both the drill hole diameter and the drill pattern were such that when loaded with explosives, the factor in terms of pounds/cu. yd. was extremely high. On the other hand, in 1982 we were in an underground coal mine where just one hole was used to prepare a 20-ft. (6m) wide face. In this coal mine, they brought down 7 yd3 (5.35m3) of coal with just 1 lb. (.454 kg) of explosive. On a pipeline job, the factor may only be .1 yd3 per lb. of explosives. Open pit operations in the same geographical area may have almost the same type of rock, but similarities could end there. The several operators over the years will have installed different size-crushing equipment or variances will exist in other facets such as drilling, excavating, and haulage units. That tells us that if we have 6 operations in that common area, we are faced with a fact that there is an optimum drilling and blasting pattern for each of those six. We start at that point. We will note from Figure No. 2 the simple equations for determining either cu. yds. or tons. For a rock heavier than limestone, it may require only 10 to 11 cu. ft. (.31m3) for 1 ton (.91 metric ton) of rock in place.

Jan 1, 1986

By Hamid Maleki

This paper reviews a study conducted for Australian Coal Research Limited (ACARP) to assist Anglo-American operations with better understanding of coal burst mechanics and control based on U.S. practical experience, investigations, and inspections in three major U.S. coalfields over the past 45 years. The study examined both nonviolent and burst-prone case studies to identify contributing risk factors and addressed failure mechanisms for major U.S. coalfields in Utah, Colorado, and Kentucky, which have diverse characteristics. To investigate the mechanics of coal burst, a multipronged approach is used. First, field measurements in three mines from East Mountain, Utah, are complemented with finite-difference stress analyses to address the importance of horizontal stress in coal pillar mechanics of violent failure. Second, the computational procedures for estimating seismicity resulting from slip along geological discontinuities are reviewed, as these measurements point to seismicity being the trigger mechanism for violent failure of marginally stable structures. This joint-slip seismicity mechanism is in agreement with the more recentimproved re-examination of mining-induced seismicity (MIS) data from the Crandall Canyon Mine, Utah by University of Utah (UOU). Third, a hybrid statistical-analytical methodology is applied for identifying significant factors affecting coal burst. It utilizes data from 30 case studies including those from Utah, Colorado, Kentucky, and other eastern U.S. mines. The statistical approach reinforces field measurements and points to strata rigidity, joint spacings, and horizontal stress field as significant factors affecting damage resulting from coal bursts. This provides practical capabilities for identifying operations of higher risk using a rigidity-cavability variable. Overall, the study provides valuable insights into the mechanics and risk factors associated with coal bursts in major U.S. coalfields. By utilizing a multipronged approach that incorporates both field measurements and statistical-analytical calculations, the study offers practical capabilities for identifying operations of higher risk and improving coal burst control.

Jul 1, 2023

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970's is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972

By EREN KOMURLUR, ATILA GURHAN CELIK, IBRAHIM GUNES

In this study, laboratory and site studies were performed to investigate the usability of a new insertion apparatus designed for the split-set type of friction bolts. The new apparatus decreases the friction during the bolt insertion by a temporary diametric compression of the split tubes. According to the results, the new precompression apparatus was found to be advantageous in terms of the insertion practicality and prevention of the buckling problem. By allowing increases in the ratio of bolt diameter to drill-hole diameter, the new apparatus was found to supply relatively high normal stresses and friction capacity in drill holes after opening its clamping mechanism.

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By F. H. Buttner

Commodity currency intrigues most of us because of the problems it offers to solve for the Third and the First Worlds. What problems might be solved, if commodity currency were to be adopted in the Third World? That is really the question we are probing here right now. It would take a while to think through all their subtle consequences of this question, but, off the top, it might well have at least three important impacts. Most important of these to this audience is relief from unfair Third World competition. Second, it might well liberate Third World economies from financial indebtedness to the First World and give them freedom from the liquidity limitations. The third benefit is that it might help relieve World trade tensions. All three benefits are interrelated. We could start our speculations on the application of commodity currency from anyone of these starting points. But let us use the starting point most important to you, unfair competition to the U.S. mining industry. From there we might wind up with some thoughts on things you, yourselves, can do to improve things.

Jan 1, 1978

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By R. Bishop, J. Baggett, J. Monsalve, N. Ripepi, A. Soni

Technology plays an ever-increasing role in improving the safety and efficiency of mining operations. Laser scanning and photogrammetry are two useful methods for capturing 3D digital representations of real world objects. While both technologies have been applied to the mining industry in numerous ways, the practical applications in an operating underground limestone mine has been tested for this paper, including for visualization and site characterization. Each technology is capable of creating highly detailed geospatial point clouds, but are all point clouds created equal? This paper presents a comparison of a laser scan and photogrammetry of a limestone pillar and addresses the strengths and limitations of each method for creating digital models of operating underground limestone mines. INTRODUCTION The United States crushed stone business is a ~$14 billion per year industry representing 1,430 companies which operate 3,782 mining operations across the 50 states. In 2017 alone, 1.33 billion tons of crushed stone was produced with 76% used predominately for road construction and repairs, but also for the production of cement, lime, chemical and agricultural uses. Over 70% of domestic crushed stone producers source their material from limestone and dolomite deposits, with currently only 82 mines (2%) operating underground (USGS, 2018). Underground mining requires a different technical skillset, and poses great challenges for production that must be both safe and economical. Therefore, there are many risks that an operation must mitigate in order to produce underground limestone. Some of the challenges in underground limestone mining involve geological hazards that are unique to the rest of the industry. The geologic features such as faults and weaknesses can be difficult to assess in a production environment (NIOSH, 1998). The consequences of failure due to improperly designed underground mining ground support systems, such as from a roof failure, are not only life threatening for the miners themselves, but can easily shut down an entire mining operation.

Jan 1, 2019

By Jorgen Elbrond, Xiaoli Tang

In this paper we apply continuous-time option pricing theory (Dixit 8 Pindyck 1994) to show how to obtain an optimal investment rule for a mining project which requires sequential in- vestments. The application per se is to some extent very simple. The main purpose of the paper, however, is to draw the attention of mining people to how the option pricing theory may be used to capital investment decisions. This topic in economics is quite new but is attracting a lot of attention.

Jan 1, 1996

By Brent A. Elliott, J. Richard Kyle

This article reviews the production trends of industrial minerals since 2000 for Texas, the leading U.S. producing state of industrial minerals with a total value of $5.2 billion in 2017, equivalent to 6.9 percent of all U.S. minerals value. Most current Texas industrial-mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is concentrated in the 25 metropolitan areas of the state, with production of industrial minerals in nearby counties. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to meet in-state and regional demand. Texas’ most rapidly growing production of industrial minerals is industrial sand to supply proppants for multiple unconventional petroleum plays. Texas’ favorable geology and economic factors provide opportunities for the identification and development of new industrial-mineral production sites. Repurposing of former industrial-mineral production sites for post-production development likely will increase as efficient land use evolves. Understanding the geologic, economic and societal framework of industrial-mineral resources will facilitate more informed decisions about the complex issues that the region will face, including effects of sea-level rise on coastal infrastructure.

Because the Environmental Protection Agency has identified methane as a greenhouse gas, the importance of de gasification through gob wells has become more critical. It has been observed that the degree of methane emission is closely related to the geomechanical characteristics of coal bearing strata, roof, floor, and surrounding coal seams. Monthly production data from 250 gob wells were collected from the Warrior Basin in Alabama, and many interesting correlations were observed between methane production with longwall face width, face advancement rate, number of gob wells in a panel, and geologic columns. Extensive finite element analyses were performed to estimate the characteristics of the emission zone in an attempt to corroborate these findings. This paper describes an investigation for developing correlations between the geomechanical behavior of the methane emission zone with methane production.

Jan 1, 1996

By J. W. Gulyas

Settling a contract for process design involves a negotiation between the design engineers and the client. Clients wish to offload as much risk as possible by seeking various guarantees about the process performance. Design engineers respond with preconditions and qualifiers, believing that the risk must remain with those who stand to benefit. This paper presents the engineers? point of view on guarantee types and precedents, performance testing, damages that may be claimed, and remedies that can be provided with particular reference to the mining industry.

Jan 1, 2010

By Emmet K. Oslen

Kaiser Steel Corporation, the pioneer steelmaker on the Pacific Coast, was founded by the late Henry J. Kaiser. In 1944 the Company purchased from the Southern Pacific Railroad an iron ore property 200 miles east of Los Angeles known as Eagle Mountain. Today the domestic operation of Kaiser Steel Corporation consists of the iron mine at Eagle Mountain; two coal mines, one each in Utah and New Mexico; an integrated steelmaking complex at Fontana, California; and several steel fabrication and erection facilities along the west coast. Kaiser Steel also has interest in Hamersley Iron, Ltd., Australia, and Kaiser Resources, Ltd., British Columbia. Eagle Mountain Mine is located about 80 miles east of Palm Springs and adjacent to the southeast corner of Joshua Tree National Monument. The area is one of the most arid in the world averaging only two inches of rain annually. Geologically, the mine is at the western edge of the Basin and Range Province which covers about one-half million square miles of the western United States. The Province is typified by north to northwesterly trending fault block mountain ranges separated by sediment filled valleys, Production has totaled over 82 million tons of finished products since the first shipment in June, 1947. Over 500 million tons of material have been mined from the deposit to date. Eagle Mountain Mine is noted for the pioneering use of the largest and most up to date equipment to mine and process its ore. In 1961 Eagle Mountain received the first fleet of 100-ton haulage trucks in the mining industry. There were thirteen semi-trailer units in the fleet. The first 12 to 17-yard size shovel in the mining industry was placed in operation at Eagle Mountain during 1962. Rotary drilling was introduced at Eagle Mountain in 1954 to replace churn drilling. Eagle Mountain was the first major mine to use metallized slurry when three aluminum slurries were introduced for primary blasting in 1962.

Jan 1, 1972

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of 4 foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with MSHA’s lower coal mine respirable dust standard (1.5 mg/m3). Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used a low pressure air generated by a blower and water pressure using a NIOSH developed foam generator. Foam property tests comprising of a bottle shake test, foam expansion ratio, and water drainage were used to classify foams. The bottle shake tests determined that the lowest concentration of foam agent to be used was approximately 1.5%. Compressed air generated foams tended to have low expansion ratios (10-19) with high water drainage. Blower air generated foams had higher foam expansion ratios (30-60) with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The different foam agents produce foams with different material properties. Results of testing eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents, while having different foam properties, seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. INTRODUCTION About one-half of U.S. underground coal is produced by longwall mining. This technique allows for mining high volumes of coal, producing significant amounts of coal mine dust. This can lead to the overexposures to longwall miners and possibly occupational respiratory diseases black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [1]. When respirable quartz is present, the mine must maintain an average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present [2]. Respirable dust samples collected by U.S. Mine Safety and Health Administration inspectors for the five-year period from 2010 to 2014 found that 5.6% (53 of 943 respirable coal mine dust samples) of the longwall operators on the tailgate side exceeded the coal mine dust standard, and 4.3% (76 of 1768 samples) of the jacksetters exceeded the standard. If silica is present, the reduced standard is implemented, meaning that 11.4% (36 of 316 respirable coal mine samples analyzed for dust) of the jacksetters exceeded the reduced standard. Only 3.8% (18 of 478 samples) of the longwall operators on the tailgate side exceeded the reduced standard [3]. Had the 1.5 mg/m3 standard been in effect during this period, non-compliant samples would have been much higher. For example, over 15% of the samples collected at the tailgate shearer operator occupation exceeded the lower standard."

Jan 1, 2017

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not coprecipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Nov 1, 2011

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not co-precipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Jan 1, 2011

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By O. H. Rostad

The importance of geology in ore reserve estimation has been stated by several authors. King et, a1 (1982) reported that the geological factor was the key deficiency where serious weaknesses in ore reserve estimation appeared, especially in grade. The foundation for a successful mining operation is an ore reserve estimate that neither overstates nor understates the true situation as to tonnage and grade. Overestimation of reserves can have devastating economic results. Overestimation of tonnage may lead to wasting money on an overbuilt plant or worse yet, if grade is seriously overestimated also, to undertaking an operation that is doomed to economic failure from the outset. Understated ore reserves can result in building a plant that is smaller than optimum which may result in higher unit costs. At worst, understated tonnage of ore reserves can result in a missed opportunity for a profitable operation. Failure of the ore reserve estimator to properly take into account all geologic and allied factors pertaining to the deposit can result in an ore reserve estimate that is overstated either as to tonnage or grade or both. This paper will focus on these factors and will not discuss rules about distances above or below a drift that should be given a classification of proven or probable, etc. Each deposit has its own particular characteristics which often require modification of general rules for defining limits of proven and probable ore blocks that work satisfactorily in another deposit. A number of references are included which discuss some of these problems. Definitions of ore reserve classifications and an illustration are given in the Appendix.

Jan 1, 1985

By Jacques LeBel

After a brief definition of asbestos and a review of regulations, the elements of asbestos dust control are outlined for various asbestos manufacturing industries. To prevent the asbestos dust to become airborne, the general procedure is to control the dust at the source by enclosure and exhaustion. The asbestos dust is collected and removed from the air with bag filter collectors of high efficiency (better than 99%) to ensure that the air emitted to the general environment or returned to the workplace are below the existing asbestos emissions regulations. Dust control systems should be regularly inspected and serviced to maintain at all times the efficiency and reliability of the equipment. Other effective procedures for asbestos dust control are also considered.

Jan 1, 1984