Search Documents

By M. Bai

The influence of mining on the hydro-geomechanical environment is greatly constrained by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of geometry changes, can be reasonably predicted through a coupled finite-element model introduced in this paper. Verification of the model has been tested using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1993

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By Armando Correa de Araujo

Cationic flotation of quartz is currently utilized for the concentration of iron ores and for the cleaning of phosphate concentrates. The present work deals with depression of quartz in the presence of aluminum ions during cationic flotation. It was established-that aluminum ions depress the flotation of quartz with an amine, especially under neutral and very slightly alkaline conditions. Studies of adsorption of Al ions on the quartz surface as a function of pH correlated with depression of this mineral with an amine as collector. The presence of Al ions also enhanced the depressant action of corn starch on quartz The sodium salt of ethylenediaminotetra-acetic(EDTA) was found to be an effective complexing agent to supress the depression caused by aluminum ions.

Jan 1, 1984

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By Peter G. Zambas

In planning an underground room and pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore-body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1971

By J. H. Canterford

To date, large-scale solution mining has received little attention in Australia, although the potential of this technique has not gone unnoticed. The possibility of long-term damage to the local environment has also been recognized. Because no two orebodies are the same, it is clear that the application of solution mining techniques and the assessment of environ- mental damage will be somewhat different for different orebodies, even though the general principles will be the same. At present the most significant copper solution mining operation in Australia is at the Mammoth (Gun- powder) Mine in northern Queensland. This mine currently produces more than 3 000 t of cement copper a year.1

Jan 1, 1981

By Dale R. Andrus

Why is there such an increased thrust toward positive multiple use land management and where will it lead? History and purpose of the mining law of 1872. John Marshall discovered gold at Sutter?s mill near Coloma, California, on January 19, 1848, and utter chaos resulted. The great migration of people to the undeveloped western lands had begun. Prior to this discovery, copper, lead, and iron had been the minerals for which the laws were made. With this discovery of gold on the public domain, it became apparent that congressional legislation was necessary. This became even more apparent as each of the numerous mining districts which were springing up in California, and elsewhere in the west adopted local miners' customs to regulate their activities. Although these early miners acted under mining district rules and in some cases state regulations, they were, in reality, appropriating minerals without sanction of federal law.

Jan 1, 1970

By B. J. Sauer

Misapplication of AC induction motors for mine crusher and mill applications has long been a frustration for both the driven equipment supplier and the mine operator. Proper selection of AC induction motors is critical to providing efficient production. This paper focuses on the selection of AC induction motors for gyratory crusher, cone crusher, and grinding mill applications. The criteria for motor selection includes: proper enclosure, driven equipment torque requirements, bearing life, temperature rise, starting requirements, ambient temperature, altitude and accessory requirements.

Jan 1, 1999

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By Vikram P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in terns of the compression strength, impact resistance (drop test), abrasion resistance and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder used. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1981

By H. C. Rolseth

The first step in the quarrying of granite, following removal of any overburden material, involves the freeing of large blocks from the formation. For many years the use of explosives was the accepted method of obtaining these blocks. Even today there are operations where this is considered to be the most economical method even though it does result in a high percentage of damaged stone. In more recent times the preferred procedure at most quarries has been to produce a continuous vertical cut or slot completely around the block to be separated. Originally, this was done by drilling a series of closely spaced holes around the block and breaking the web between the holes with a chisel-like tool known as a broaching bar. The machine used in this mechanical method of producing the relief slot is known as the channel bar. The modern day approach to the production of continuous channels was introduced to the industry around 1955 by the Linde Division of Union Carbide Corporation. The method employs a small rocket - jet burner producing a high temperature, high velocity exhaust flame which when directed against the granite causes it to disintegrate. This method, which has come to be known as "Jet Channeling", is now used by practically every major granite producer in the United States and Canada.

Jan 1, 1968

By Don L. Deardorff

The Deserado Mine and transportation system is the fuel supply portion of the Bonanza Power Plant project. Deserado Mine con¬sists of an underground mine with a capacity of 1,224,700 tonnes (1,350,000 tons) of clean coal per year, a 649 tonne (715 tons) per hour closed water circuit jig type preparation plant, a 5.6-kilometer (3 ½ -mile) overland conveyor with covered slot storage, a unit train rail load-out and 59.5 kilometers (37 miles) of totally independ¬ent, captive electrified railroad. Planning and exploration started in March of 1978. Construction of all facilities was completed in April of 1984, approximately six years after initial planning was commenced. This paper will discuss exploration, environmental permitting, mine planning, engineering and construction of the Deserado Mine project.

Jan 1, 1984

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

By Tracey A. Conrad, Mark E. Mussett, Max Kaufmann

The varied benthic habitats of the Pacific Ocean are comprised of different types of seafloor geology. These geologic domains generally consist of sedimented abyssal hills, high relief features such as seamounts, and polymetallic nodule fields that vary in spatial extent and abundance. Nodules represent a deep ocean habitat type, and are of economic interest owing to their metals content. Multibeam data can be used to classify seafloor geology. The wide swath of hullmounted multibeam systems used in deep water provides efficient coverage of large areas of seafloor. Our research examines how multibeam backscatter and bathymetry data, with regional environmental parameter assessments and GIS analysis, can help identify probable polymetallic nodule fields in the deep remote ocean prior to groundtruth seafloor observations. A workflow for processing 30 kHz hull-mounted multibeam data within QPS Qimera and FMGT software was developed to facilitate multibeam processing, while also generating a terrain model and backscatter products. An additional GIS protocol for evaluating multibeam data products, including cluster analysis, was also developed. These methods were applied to a test case of publicly available multibeam data collected by the Ocean Exploration Trust and NOAA. Processed multibeam products were used to identify areas exhibiting coarse sediment backscatter characterization with low relief; filters for water depth at or below the regional CCD, seafloor age, and sedimentation rate were then applied. Sophisticated GIS cluster analysis further identified trends within the data to forecast where coarse sediment domains, potentially including nodule occurrences, exist. The test case multibeam data allow determination of the composition and variability of seafloor geology. This analysis can further identify where previously unexplored nodule fields may exist and edify estimates of nodule extent throughout the ocean. The research methods and outcomes contribute to marine spatial planning, ecosystems modelling, and mineral resource management initiatives.

Feb 22, 2026

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By Alistair James, Mo Shahsavari, Leon Botham

The 1889 Johnstown Flood, which killed 2,209 people, was a preventable disaster stemming from systemic decisionmaking failures. This paper applies modern Risk-Informed Decision Making (RIDM) frameworks to analyze the historical context and explore alternative outcomes through hypothetical multiverse scenarios. By reconstructing the risk landscape of the South Fork Dam, we demonstrate how structured hazard identification, risk assessment, and stakeholder communication could have mitigated or prevented the catastrophe. Three counterfactual scenarios—proactive maintenance, community engagement, and regulatory oversight—are evaluated to quantify potential lives saved and economic benefits. The study acknowledges historical barriers, including technological limitations, lack of governance, and socioeconomic disparities, which constrained risk-aware decisions in the 19th century. The analysis draws critical parallels to contemporary engineering challenges, particularly in tailings storage facility (TSF) management, where similar risk blind spots persist. The paper concludes that RIDM is not merely a technical tool but a governance imperative, essential for ethical and sustainable engineering practice. By learning from historical near-misses and failures, the modern engineering community can strengthen resilience and accountability. This work contributes to the growing body of retrospective risk analysis, offering a methodological framework for applying RIDM to historical disasters to inform future safety standards.

Feb 22, 2026

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017

By R. Ribeiro

The designers of the new Arafertil concentrator in Brazil provided for complete automatic control of the grinding circuit to meet the operating objective of maximum throughput at a specified grind. Analog control methods were selected because of proven reliability and simple maintenance, and in order to minimize commissioning time and effort. This paper summarizes the step-by-step effort required to progress from local loop control of certain individual parameters to an integrated system capable of achieving the design goal. Emphasis is placed on the practical aspects of commissioning a control system.

Jan 1, 1979

By A. Lashgari

Surface coal mining in the Appalachian region consumes a significant amount of energy in the form of diesel fuel and blasting agents. emission of oxides of nitrogen (Nox) from these sources represents an environmental challenge to the mining industry. this paper presents the results of research work related to determination of Nox emission of mining equipment and blasting agents, which is part of a broader industrial project conducted by the Appalachian research Initiative for environmental research (ArIeS). Data for this project are collected from an operating surface coal mine in West Virginia. the research work presented here may be used by mining professionals to aid in quantifying Nox emission and determine strategies for reducing its overall environmental impact.

Oct 1, 2013

By D. Wenstrup, K. Perry, J. Hatfield, P. Sainato, B. Lusk

Concrete-infused cloth is used in several civil and mining surface applications whose circumstances are similar to some of those in underground mining. A feature of this material is that it cannot be overhydrated. In underground conditions, however, the excess supply of water to the cloth for hydration could lead to muddy and potentially unsafe working conditions, as well as resource wastage by supplying more water to the construction site than is needed. The objective of this study is to verify the water-to-cloth ratio and study the effect of hydration level on the strength of the Concrete Cloth product. We found that the strength increases with increased hydration up to a 1:2 water-to-cloth ratio by weight, after which the strength holds steady regardless of additional hydration. This confirms the 1:2 water-tocloth ratio by weight for hydration and confirms that strength is retained even if the cloth is excessively hydrated.

Jan 1, 2014