Search Documents

By John D. Smith

This paper describes how a knowledge of inherent rock characteristics can aid the mining engineer in his design of a mining method for a massive domelike structure. The paper shows how the pertinent rock characteristics were measured and analyzed and how the data obtained was used for design purposes. This analysis was conducted in 1964 in a producing salt dome, since that time, mine management has tried certain of the recommendations for mine design changes. The results of such changes are presented.

Jan 1, 1968

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By M. Deniz Turan, HASAN NIZAMOGLU, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings, or flotation waste, formed during copper production may be considered in the class of valuable wastes because of the amount of copper they contain. With the decreasing grade values of copper ores, the utilization of wastes like tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental senses. This study was carried out with the aim of using ammonium derivatives for the recovery of copper from tailings waste produced during copper production and utilizing their complex formation characteristics. In the conditions of six hours of leaching at 30 °C in the presence of 22.5 percent ammonium hydroxide and 100 g/L ammonium persulfate, 91.47 percent of the copper was transferred into the solution, while iron was not transferred, indicating that copper can be selectively recovered from tailings.

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By R. K. Singhal

In 1990, Canada produced 69.4 million tonnes of coal of which some 65 million tonnes was produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia produce approximately 55 million tonnes of coal by surface mining. These two provinces also provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5m to over 8m. Most of the Canadian surface mines are large (over one million tonnes per annum) using modern mining equipment such as shovels, high capacity trucks and draglines. At present the industry is going through another of its up and down cycles but has continued to make impressive gains in productivity. This has been achieved through greater mechanization, better management practices and a will to succeed in a highly competitive world market. This paper presents an insight into the current status of the Canadian Coal Industry and essentially updates the information given by the authors at previous SME meetings.

Jan 1, 1992

By S. Goodfellow, J. C. Ordóñez-Calderón, K. Esmaeili, N. Houshmand

A good understanding of the hardness of ore being handled and processed in a mining operation can significantly improve operational efficiencies by providing valuable data to support decision-making through the mining value chain (drilling, blasting, comminution). This study presents the results from the application of Machine Learning (ML) to predict rock hardness using various geophysical and geochemical features. Core samples from a mine site were logged using a multi-sensor core logging system. Measurements including ultrasonic p-wave and s-wave velocity, elemental concentration via portable XRF, and Leeb Hardness, were measured every 2 cm along the length of the core. The ML model was set up to predict the Leeb Hardness using the elemental concentrations and ultrasonic velocities as predictors. The Leeb Hardness values were grouped into three bins and used as a classification target for the ML models. Various ML models, including linear regression, support vector machines, decision tree, XGBoost, Random Forest, K-Nearest Neighbors, and Naïve Bayes were tested. The model performance demonstrated that the Random Forest and XGBoost models produced the highest accuracy of 74-91%. Random forest and XGBoost were then selected to perform regression models to estimate a Leeb hardness value rather than a hardness class. These models were able to estimate the Leeb hardness value by 4.57-4.87 % error.

Mar 2, 2022

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

By H. P. Cole

A team of researchers at the University of Kentucky, working under a USBM contract, developed over 65 simulation exercises for teaching and testing problem-solving and decision-making skills to miners and mining engineers. These skills involve both improving judgment and decision making in mine emergencies and enhancing the learning of real-world engineering design principles. The exercises are ideally suited for either latent image format or for computer-aided instruction. Exercise features are summarized, the structure and field testing of typical exercises described, and sample frames of individual exercises presented. Empirical data are summarized that describe the effectiveness of using these short, time-efficient performance tasks that simulate real problems and that provide immediate corrective feedback for teaching and testing critical skills. I

Jan 1, 1991

By Klaydison Silva, Pedro Silva, Letícia Damet

The current situation of the global mining economy is increasingly focused on the utilization of materials previously discarded in the mining process. The waste from the past, through new processing routes, is gaining new contours for use as high-value-added products. The strategic mine planning process has consequently had to adapt to the new economic reality. In standard scenarios, the focus was primarily on mine sequencing aimed at the highest economic return, with all infrastructure allocated as a necessity of mining. This work aims, in strategic planning, to configure and select the best composition of mining structures. The entire Mine-Plant-Waste-Tailings-Products chain will be considered as a factor in the sequencing of a multimine complex, to achieve the most sustainable utilization of the current mines’ waste. The sequencing is based on concurrent flows of process configurations and capacities, structure sharing, and flexibility of feed types. These factors will guide the sequencing, which will be constrained by components such as waste and tailings disposal rates, lithology feed relationships, and especially product composition through market specifications, all while respecting product shipping capacities.

Feb 22, 2026

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By C. C. Muir

At the outset, I believe reference should be made to comparatively recent world developments in copper which have an important bearing upon the Canadian position. COPPER SITUATION No one can doubt the marked change for the better compared with not so long ago when less than adequate attention was paid to marketing and to uses of the metal. I need not show you graphs of world copper prices, which except for relatively brief periods and war conditions were, until about three years ago, not unlike the topography of the Canadian Rockies. There remain, of course, some non-industry factors who yearn for the old days of "roller-coaster" copper prices.

Jan 1, 1964

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016