Search Documents

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By M. Kuchta, S. Iverson

INTRODUCTION Underground blasting with perimeter damage control can reduce the requirement for loose rock scaling and reduce the risk of ground-fall injury. In previous work Johnson and associates (2010) from the National Institute for Occupational Safety and Health (NIOSH) developed a rock blasting perimeter damage and control design method included in the DRIFT software tool (NIOSH, 2018). This blast design software tool utilizes current methods of perimeter blasting with the added design element of a buffer row coordinated with the perimeter row to reduce perimeter damage. The coordination is in applying one of several blast damage models to calculate the damage extent for each production, buffer, and perimeter blast hole in the design. The calculated damage is then applied to the spacing between the blast holes. The basis of the buffer row design is the practical damage limit and is supported in this paper with computer models of signature blasts and full blast rounds using PFC2D (Itasca Consulting Group, Inc., 2018). Practical damage limit The practical damage radius (Rd) is not to be confused with burden. The practical damage extends toward the burden side and inward into the rock mass. For all practical purposes, the practical damage radius equals one half the burden (Hustrulid, 1999). The maximum extent of radial crack damage around a blast hole (Rcrack) and the maximum extent of radial crushing damage (Rcrush) are illustrated in Figure 1. A “practical” radius of damage (Rd) lies between the crushing limit and the cracking limit. The “practical” damage means that if the rock mass lying outside of the practical damage circle were removed, the rock remaining within the circle would easily break apart. Blast pressure and strain Work by Johnson (2010) and associates included signature blast tests in large concrete blocks. A signature blast test in concrete as exampled by strain data in Figure 2 was designed to monitor the dynamic strain at incremental distances from a single fully coupled blast hole, measure crushing and radial cracking extent by wire-sawing to expose the damage, and relate the damage to overbreak that is common in underground blasting. The initial slope or rising strain as the stress wave passes by the strain gages shows very high strain and strain rates close to the single blast hole. Since the derivative of strain versus time is strain rate, a line tangent to each of the strain curves at the maximum strain rate is drawn and the strain rates identified. The high strain rates were then plotted on a semi-log in Figure 3 to show a linear trend. The strain rate is greater than 100 s-1 within 20 cm from the blast hole for the signature blast experiment. The strain rate at the blast hole wall is projected to be 300 s-1. Figure 4 illustrates the damage in the NIOSH block exposed by a wire saw cut.

Jan 1, 2019

By B. C. Haydon

Manganese silver ores are well known to be refractory towards cyanidation. Various processes have been suggested for improving the amenability of these ores. A sulfurous acid pre-leach is one such process. This paper traces the development and implementation of the sulfurous acid pre-leach process for the retreatment of manganese silver tailings at Tonopah, Nevada. An account of the test work program is presented, followed by a description of the operating plant and specimen metallurgical performance. The paper also summarizes the history of the Tonopah tailings, their mineralogy and makes reference to previous application of the sulfurous acid pre-leach process.

Jan 1, 1984

By Michael E. Karmis

New and developing communication systems en-able underground miners to, not only connect to the surface from an increased communication coverage area, but also to be discovered in the event of an emergency. Communication and tracking systems are required by the U.S. Mine Safety and Health Ad-ministration (MSHA) regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broad-cast devices results in a reliable communication network that can better withstand disruption in daily operation and during a time of emergencies. Research on wireless communication in mines has been ongoing since 1922, when the U.S. Bureau of Mines performed experiments in its experimental mine in Bruceton, PA (Schiffbauer & Brune, 2006a). Ac cording to Dobroski and Stolarczyk (1982), ?as early as 1922, Bureau of Mines experiments showed that radio propagation in mines was possible but not practical.? In 2006, the underground communication technologies available to the mining industry had inherent problems that limited communication capabilities. Because harsh underground mine environments significantly reduce line of sight and propagation range and introduce power and safety concerns, the overall effectiveness of underground communication technologies were limited. After several coal mining accidents in early 2006, the U.S. Congress responded with the Mine Improvement and New Emergency Response (MINER) Act, enacted

Jun 1, 2010

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By William I. Weisman

Natural sodium sulfate is obtained from both brines and solid deposits. The brines almost always contain other salts with sodium chloride predominating. They may be obtained from surface occurrences, such as Great Salt Lake or from shallow subterranean deposits. Althought many sodium sulfate minerals are known to exist, only three are of commercial significance. These are thenardite, the anhydrous salt; mirabilite, the decahydrate; and glauberite, the double salt of sodium and calcium sulfate. The reader is referred to Weisman (1983) for details on mineralogy and geology of sodium sulfate minerals. Sodium sulfate deposits, either in the form of brine or solid minerals, are found in many parts of the world. Natural sources, by far, provide the primary supply of commercial grades in Canada, Mexico, Spain, and probably in the U.S.S.R., Chile, Argentina, and Turkey. In the United States, production of natural material and synthetic (including by-product) are about equal in volume and have been for many years.

Jan 1, 1984

By Paul W. Johnson

Chemical mining is the in situ extraction of metals from ores located within the confines of a mine (broken or fractured ore, stope fill, caved material, ores in permeable zones) or in dumps, prepared ore heaps, slag heaps, and tailing ponds on the surface. These materials represent an enormous, untapped, potential source of all types of metals. The field of chemical mining, now in its infancy, encompasses the preparation of ore for subsequent in-place leaching, the flow of solutions and ionic species through rock masses and within rock pores, the leaching of minerals with inexpensive and regenerable lixiviants under prevailing conditions of the in-place environment, the generation and regeneration of such solutions, and the recovery of metals or metal compounds from the metal-bearing liquors. It is not inconceivable that eventually our ore reserves will consist largely of low-grade, refractory, and inaccessible new deposits and low-grade zones near previously worked deposits, caved and gob-filled stopes, waste dumps, tailing ponds, and slag-heaps. Chemical mining promises economic recovery from these types of deposits. Before it can come of age, however, a much better understanding is needed concerning its chemical and physical aspects.

Jan 1, 1967

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By R. H. Hanewald

The processing of EAF baghouse dusts from both the specialty steel industry and low alloy producers will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions or filter cakes, spent nickel and chromium plating baths, carbon refractories from pickling tanks, and super alloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery. This, along with the details of INMETCO's BDAT Test Program and results performed to pre-agreed standards with the EPA will be discussed.

Jan 1, 1992

By Kunzo Amano

Fully-bonded rock bolts have been widely used in construction sites and mines in recent years. The purpose of this investigation is to prove the effectiveness of rock bolt supports in unstable ground through in-situ tests and numerical analysis. 2. MEASUREMENTS AND PROCEDURES OF IN-SITU TESTS The fully-bonded rock bolts as the mine road¬way supports were tested in the Fukasawa mine which is located in the northeast district of Japan (Fig. 1). The Fukasawa mine (one of the Kuroko mines) started the production in 1973, and the present monthly production is slightly less than 20,000 tons. The ore deposit which exsists at about 400 m depth is divided into several small lenticular shaped bodies. They are distributed apporiximately 1500 m in NW-SE direction and 700 m in NE-SW direction. The hanging wall is basaltic lava and the footwall is tuff. The rocks surrounding the ore bodies are soft but relatively intact, so the trackless mining system has been adopted from the beginning of the development.

Jan 1, 1982

Ferric (Fe3+) ions are omnipresent in flotation circuits. Depending on pH and the nature of the ore body, Fe3+ ions may play a role in the adsorption of thiol collectors on sulfide minerals. To investigate this possibility, a two-compartment galvanic coupling cell was designed. This cell was used to monitor changes in contact angle of a sulfide mineral in one compartment, while varying concentrations of the Fe3+ ions in the other. The results showed that Fe3+ ions promote xanthate adsorption as indicated by the increase in contact angle. Implications of this finding in sulfide mineral flotation in general will be discussed.

Jan 1, 1998

By Donivan L. Gordon

One of the several problems facing society today is that of disposing of its solid waste. Each year this nation spends approximately 4.5 billion dollars to collect, transport and dispose of some 360 million tons of domestic and industrial solid waste. Although considerable sums of time and money have been spent in researching various techniques for solid waste disposal, it is presently agreed that sanitary landfilling represents the most economic and universally adaptable solution to the problem of solid waste disposal. However, regardless of the factors favoring sanitary landfilling as the waste disposal method of choice, it should be recognized as carrying with it a potential for the degradation of ground- and surfacewater resources. Through an interdisciplinary effort regulations were promulgated during 1971 in the State of Iowa to govern sanitary disposal projects. Consistent with a set of rationales developed to preserve environmental quality, these regulations set forth hydrologic and geologic standards designed to protect Iowa's water resources. Minimum requirements have been outlined in the regulations through which the natural favorability of potential landfill sites may be evaluated. Natural favorability is primarily defined in terms of the hydrologic and geologic relationships between a proposed landfill site and those in the locality of the site. The regulations specify that leakage from a landfill to a subcropping aquifer must be less than 0.04 cu ft/day/sq ft at the base of the landfill. This factor is offered to quantify the maximum allowable leakage for all sites in unconsolidated sequences underlain by subcropping bedrock aquifers, Based on groundwater research in Iowa, the assumption is made that 50 feet of till will be sufficient to inhibit the downward flow of liquids from a landfill into bedrock aquifers. This assumes a difference of no greater than 40 feet in hydrostatic head between the water table in the unconsolidated sequence and that in the bedrock aquifer. Owing to the fact that bedrock aquifers in many areas of the state are mantled by less than 50 feet of till the regulations provide for site modification, through engineering, to meet the specified leakage standard, In such instances the leakage factor is evaluated by means of the generalized Darcy's Law Q = PIA where:

Jan 1, 1974

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By QUANWEN PU, Yonggang Wei, Bo Li

The spent catalyst is one of solid waste resources, which contains precious metals with considerable recovery value. However, due to the different compositions of catalyst, the recovery process is difficult. Most of the catalysts are supported by alumina which has good alkali-soluble properties, while platinum is insoluble in alkali. Platinum is enriched by pressurized alkaline solution which is a kind of hydrometallurgical process. The novelty of this study is the separation of alumina and platinum from the spent catalyst and the enrichment of platinum in the solid phase. In this study, a leaching process using NaOH as leaching agent under high temperature and pressure was employed. The effects of alkali concentration, leaching temperature, leaching time, and liquid–solid ratio on leaching efficiency were investigated. The optimum process conditions were determined as follows: alkali concentration of 240 g/L, temperature of 200℃, pressure of 1.20 MPa, time of 1 h, liquid–solid ratio of 5:1. It was concluded that the leaching rate of alumina can reach 99.69%. The content of platinum increased from 0.1749 to 21.12%, the loss of platinum was 3.39%, and the enrichment ratio of platinum increased by 120.82 times. The leaching kinetics of alumina was studied based on the shrinkage core model. The activation energy of alumina leaching is 19.53 kJ/mol, and the leaching process is controlled by chemical reaction. Pressurized alkali solution can not only efficiently leachate alumina from the spent catalyst and enrich platinum, but also reduce the reaction time and increase reaction rate.

Feb 11, 2022

By K. Lapakko

Kinetic tests results are influenced by methodological variables, including test duration and mine waste particle size. Some samples tested produced neutral drainage in kinetic tests for more than two years prior to drainage acidification. The potential for long "lag times" can be assessed based on the mine waste mineralogy. The lag time duration can be estimated using this mineralogy in conjunction with dissolution rates observed in the kinetic tests. The influence of particle size on the drainage quality is dependent on the variation of the availability of acid-producing and acid-neutralizing minerals with particle size.

Jan 1, 1998

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By Stephen Semeniuk

Working with junior mining companies as a valuer, my experience with regulators is that simplicity works and the sales comparison method is the way to go. What I like about Mr. Ellis?s approach (as in his Table 7) is the integration of commodity prices with the timing of acquisitions and the implication of price changes in gold on the adjustment of individual project valuations. However, the sample gold-related appraisals in Ellis?s paper are pre-2008 transactions and readers should be made aware of the current market for such projects. Before moving on, to be noted is that the effective date of the Las Brisas appraisal (Ellis?s sample Appraisal 3) is Feb. 10, 2006; given that the subject value of Transaction 9, Choco 10 in Ellis?s Table 6 was listed as $353 million for a 95% interest in the con-cession, I am uncomfortable accepting that the acquisition was suddenly worth the adjusted value of $1,205 million (as given in Ellis?s Table 7). In some cases, illiquidity discounts can apply, and commodity-wise, in the one-month period between the acquisition in January 2006 and the adjustment to the Las Brisas conditions as of February 10, 2006, the indicated gold price change was only 41 cents/g ($12.60/oz); i.e., from $17.50/g to $17.91/g ($544.40/oz to $557/oz).

Jan 1, 2012

By R. L. Bonomi

Developing a mining venture in a foreign country, particularly in South Africa, can be a real challenge to those involved in the operation. The mining division of Southland Energy Corp. was asked to offer consultative support to the New Union Gold Mine, located in the Giyani District, Transvaal, Republic of South Africa, to aid in their expansion from an approximately 65 tonne per day exploration- exploitation project into a full scale mining operation of 300 tpd by January, 1987 with further expansion to 600 tpd by mid-year. This paper ad- dresses the development of the expansion plans, which are presently being implemented. History. Located in the Northern Transvaal, Republic of South Africa, the New Union Gold Mine is part of what is known as the Klein Letaba gold fields. Gold prospecting in the Klein Letaba gold field area dates back to the earliest years of European prospecting activities in the Transvaal where, reportedly, gold was discovered as early as 1887 (figure 1). The claims com- prising the present New Union Gold Mine have been explored by a number of individuals and relatively small mining groups since the early 1930's. The work done by these entities was aimed at recovering as much gold as possible in the quickest and cheapest manner possible and, as a result, the area was not explored in a systematic fashion. The long-term potential of the area, therefore, was not known until very recently.

Jan 1, 1987

By Steve Axen

In situ mining is now considered an alternative mining method for some ore bodies. The in situ operation consists of a well field designed from reservoir properties and geological information; the wells for such a field are then drilled, cased, and cemented, using good designs and practices to eliminate future problems. Injection and production (recovery) systems are required to be corrosion resistant. Hand in hand with the mining operation is the metal extraction plant, the entire operation offering an environmentally acceptable method for metal recovery. Great opportunity exists in this field for mineral engineers; presently, they must borrow knowledge from other fields, since the schools have not yet addressed this specialty.

Jan 1, 1979

By Ralbern H. Murray

Typical First Year Selling Price Strip Mined Western Sub-Bituminous Coal Based [Fixed Capital (1) $600 MM Construction Loan Interest $100 Working Capital $ 30 Start-up Costs $ 30 Total Capital Requirement $760 MM Annual Costs (First Year) $M/Year Coal (2) 443,550 Operating Costs(3) 53,000 Depreciation(4) 36,500 Interest(5) 45,220 After Tax Profit(6) 34, 200 Federal Income Tax (48% Rate) 31, 570 Gross Revenue Required 245,040 (Less) By-Product Sales (18, 000) Net Revenue Required 227, 040]

Jan 1, 1975