Search Documents

By C. G. Hunkin

In situ, or in-place leaching is concerned with the extraction of metals from natural mineral disseminations without removal from their geologic location which, in many cases, amounts to the reversal of the deposition process accompanied by a presumed increase in velocity of the processes, if the project is to be profitable. Solution mining processes involve removal of minerals such as sulfur, common salt, and potash, generally leaving cavernous voids, in contrast to in situ leaching which term is applied to the selective dissolution of a mineral from its gangue without sensible disturbance of the formation. Where such a process can be operated, the advantages are manifold and have been so recognized by miners from the earliest days of mining. Recent technological developments have encouraged a reassessment of the status of in situ leaching, and it now appears possible to extend the application of the method from a few isolated special situations to many uranium and copper deposits. Anaconda's interest in the techniques stems from long experience with vat and heap leaching, 'dump leaching, and natural leach activities associated with several established mines. Increasing activity through-out the industry has been noted, particularly in leaching low grade pillars and the peripheral zones of operating mines, often by the introduction of leach solutions via boreholes drilled from surface. Reactivation of dormant mines] using similar techniques has been successful. Over the long term, environmental improvement activity will lead to excess sulfuric acid production, even to a disposal problem. The cost of leach solutions and reagents must be reexamined in this light. The mineral industry now classifies as uneconomic deposits of readily soluole minerals whose potential value, on a per acre basis, may De several times that of many currently profitable oil field reser-

Jan 1, 1971

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By R. O. Harma

Wet autogenous grinding is utilized in three iron ore concentrating plants operated by The Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping.

Jan 1, 1982

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By Cheng Xie, Zhihu Li, Xiaoming Sun, Linsen He, Jiaxu Ding, Jinkun Yang, Yong Zhang, Zhenmin Qi

To solve the problem of large deformation of deep soft rock roadway, taking the soft rock roadway of no. 1 coal mine in New Shanghai as an engineering example, the deformation mechanism of surrounding rock of deep soft rock roadway is analyzed by combining theoretical analysis, numerical simulation and field test, and the control countermeasures centering on deep and shallow dense drilling are put forward. Through theoretical derivation, based on the masonry beam theory, surrounding rock structure S-R stability principle and composite beam principle, the length, angle, and spacing of deep and shallow dense drilling are determined. Through numerical simulation, the deformation evolution process of soft rock roadway surrounding rock after dense drilling pressure relief is reproduced, and the influence of drilling parameters (drilling spacing, dip angle) on pressure relief effect is analyzed and compared. The field application test and monitoring verify that the deformation control measures of deep and shallow dense drilling broken roof surrounding rock have a good effect of large deformation control of soft rock roadway, and provide a new support means for the safety and stability control of soft rock roadway.

Mar 2, 2024

By Wayne L. Johnson

The depth capability of engineering seismographs has been greatly increased by the use of signal enhancement, a technique in which seismic waveforms created by repeated impacts are digitized, stored, and summed. Summation amplifies the signal and partially cancels background noise. This gives a clearer picture of the wave aid makes it possible to determine the travel tune of signals from 'eater depth. Signal enhancement combined with continuous display of waveform, permanent recording of waveform, and precision digital readout of travel time has opened new fields of application in mining and engineering. Recent work has clown that replacement sulfides can be distinguished seismically from country rock at Bistee, Ariz. Work on the Iron Range of Minnesota indication,: that, by using a 300 pound weight as the source, the Biwabik iron Formation can be traced down dip to several hundreds of feet traverses over known areas show that reflections can sometimes be identified. Reflection, if identified preclsely, give a mere accurate estimate of depth and buried topography. Comparison of ( ) and weight drop have given some understanding of low wave amplitude varies win; source candid

Jan 1, 1971

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare's King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement's returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry's balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972

By D. Hong

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant has been studied. Experiments were carried out in an autoclave. The effect of stirring speed, temperature, pH of the solution, iodine and iodide concentrations on the dissolution of rhenium was investigated. It was found that high temperature and high pH of the solutions were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by mass transfer of iodine with an apparent activation energy of 15.77 kJ/mole.

Jan 1, 1997

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By S. Bhattacharyya

"Coal bearing rocks are low in strength and have geological discontinuities and moisture sensitivity. Roof and rib falls have been a major cause of fatalities in underground coal mines. Mine engineers design ground control plans for regulatory approvals. A number of tools are available from the National Institute for Occupational Safety and Health to design and assess these plans. Quite often there is not enough geotechnical input information available and databases are used. The Appalachian coalfields have extensive scientific studies to provide reliable regional inputs. Coal mines in the western United States and Canada have different geological and geotechnical conditions, and less available data. Use of inappropriate inputs in the tools like Analysis of Retreat Mining Pillar Stability, Analysis of Longwall Pillar Stability, and Analysis of Roof Bolt Systems may result in unsafe designs or over conservative designs. The tools are convenient but thorough understanding of the inputs, calibration with local test results, and operating experience are important for effective designs. The current paper contains examples of difficulties faced during mine planning using the above tools. INTRODUCTION Sedimentary rocks hosting coal are low in strength. Scientific studies have placed the uniaxial compressive strength (UCS), triaxial strength, tensile strength, and shear strength of sandstone, shale, siltstone, and claystone in lower range of strength among engineering materials (1). Coal bearing rocks are most often weakened by the presence of faults, folds, slickensides, bedding planes, fractures, and other geological discontinuities. The host rocks and coal are often moisture sensitive. The geological discontinuities allow water to enter the strata from surface and underground sources. This combination of low strength, structural weakness, and presence of water results in difficult ground control situations for the coal mines. Roof (2) and rib falls have been a major cause of fatalities in the U.S. coal mines. Modern underground coal mines necessitate wide entries to accommodate large production equipment. The gate roads, section entries, and the mains entries of a highly productive coal mine are as wide as twenty feet (6.1 m). The actual intersection width is nearly thirty feet (9.1 m). Adequate ground control is a key to maintain safe production in such mines. Mine engineers and their consultants routinely submit ground control plans to the regulatory authorities. While working out the necessary roof control system the mine engineers are required to demonstrate the adequacy of the proposed system. There are multiple ways to demonstrate this. Some engineers use traditional load calculation approach of roof bolts (3). Some engineers use numerical methods. Yet a large number of professionals resort to a suite of ground control design software offered by National Institute for Occupational Safety and Health (NIOSH) commonly referred to as “NIOSH Ground Control Toolbar.” These software tools are free and easy to download from NIOSH website. The software included in this package are: Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Coal Mine Roof Rating (CMRR), Analysis of Roof Bolt Systems (ARBS), Analysis of Horizontal Stress Effects in Mining (AHSM), Analysis of Multiple Seam Stability (AMSS), Analysis of Retreat Mining Pillar Stability - Highwall Mining (ARMPS-HWM). These tools are relatively simple to install and use in planning and designing coal mines and prospective coal mines. They accept a number of geotechnical inputs which are collected from either an existing mining operation or from exploratory boreholes. In the absence of necessary input parameters, the programs use default values which are drawn from databases of geotechnical properties built by NIOSH."

Jan 1, 2015

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014

By Earle Faig

Along with other transportation modes, the barge industry will be greatly effected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events have caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of our long experience in moving large quantifies of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to the barging industry. Barge companies operate on a 40.23-Mm (25 000 mile) river system which includes the East and West Coasts and the Mississippi River System. Included in the Mississippi River System are the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior - Tombigbee and Mobile Rivers as well as some smaller tributaries. The Gulf Intracoastal Waterway, which stretches along the Gulf Coast from Brownsville, Texas to Apalachicola, Florida, is also considered part of the inland waterway system.

Jan 1, 1981

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By R. Merkl

Since the 1940s, decanter centrifuges have become more important for increasingly complex solid-liquid or solid-liquid-liquid separation processes. Sometimes processed industrial or metalliferous minerals are abrasive or are treated with corrosive chemical agents. Traditional mining applications include the processing of coal, gravel and other products, where low-speed decanters, as well as screen bowl decanters and filters, dominate. These have been increasingly replaced by high-speed decanters during the last decade. Decanter centrifuges also started to play a key role in applications such as drilling muds, processing carbonates and separating SX crud in copper platinum ore concentrations of nickel and gold. Communication between machine producers and mineral processing engineers is vital for the right choice of materials and the design of the right decanter centrifuge for the individual process.

Feb 1, 2012

By H. Jung, J. Kim, Y. Lee, Y. Seo

"Shale gas has become an increasingly important source of natural gas supply in North America and around the world. Horizontal drilling and multi-stage hydraulic fracturing are the two key enabling technologies for the economic development of these shale gas reservoirs. It is believed that gas in shale reservoirs is mainly composed of free gas within fractures and pores and adsorbed gas in organic matter (kerogen). It is generally assumed in the literature that the monolayer Langmuir isotherm describes gas adsorption behavior in shale gas reservoirs. In this work, we have analyzed several experimental measurements of methane adsorption from the Horn River Shale core samples that obey the Langmuir isotherm. INTRODUCTION In nature, gas shales are characterized by extremely small grain size, extremely low permeability on the order of nano-Darcy (10-6 md), small porosity, and high total organic carbon (TOC). Shale can serve as both source and reservoir rock. The amount of gas in place in shale is strongly affected by the TOC, clays, and the adsorption ability of methane on the internal surface of solid (Martin et al., 2010). Since a considerable amount of gas in shale reservoirs is adsorbed, investigation of gas adsorption can provide critical insights into evaluation of well performance and reservoir characterization. Generally, natural gas in shale reservoirs is stored as free gas in both larger mineral pores and natural fractures, as well as adsorbed gas within organic matter (Leahy-Dios et al., 2011). EXPERIMENT METHOD & THEORY Adsorption Experiment Several experiments were carried out on 9 shale core samples obtained in a vertical well drilled within Horn River basin (Figure 1). The CH4 adsorption isotherms were measured for the different depth. In order to measure the amount of adsorbed gas, the high pressure Belsorp-HP equipment applying volumetric method was used. The temperature was kept at 298 K and pressure was increased up to 18 MPa. Approximately 5 g of crushed sample was used for each measurement."

Jan 1, 2016

By H. A. Kortmann

For the commercial production of iron ore pellets from hematite ores, as it is practiced in various pellet plants, the addition of lime has shown to be an efficient means with a view to improving cold compression and abrasive strength of the indurated pellets considerably. Unfortunately, it has also been shown at the same time, that the metallurgical properties as, for instance, swelling behavior, softening during reduction under load and disintegration of the grain, can be adversely affected to a high degree. In the course of smelting tests carried out by renowned steelworks, blast furnace operation was heavily disturbed by the swelling and early softening of the pellets, also by their disintegration in the low-temperature range, which altogether led to a considerable lowering of the smelting rate (1, 2, 3).

Jan 1, 1972

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.