Search Documents

By Zhiyuan Ma, Yong Liu, Xianjin Lyu, Jianfang Lyu, Jikui Zhou

A stable and continuous leaching process for niobium and tantalum extraction from ferrocolumbium tantalum (FT) was developed. The effects of initial concentration of HF and H2SO4, grinding fineness, leaching time, and temperature on the leaching rate of Ta, Nb, Fe, and Si were studied. Experimental results show that the leaching rates of Ta, Nb, Fe, and Si were enhanced by the increase of acid concentrate, fineness, leaching time, and leaching temperature. The optimum process conditions are HF initial concentration of 5 mol/L, H2SO4 initial concentration of 2.5 mol/L, − 74 μm percentage of 65%, leaching time of 20 min, and leaching temperature of 25 °C. Continuous leaching of FT was carried out by feeding ore and acid every 20 min. By leaching with HF − H2SO4 for 4 h, then adding appropriate amount of HNO3 into the solution and keeping for another 1 h, a high Nb extraction rate of 99.8% was achieved. The established method provides a promising technique for the high-efficiency separation of niobium and tantalum from FT.

Jun 5, 2022

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. High-grade Transvaal chalcopyrite was neutron irradiated in a TRIGA reactor to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes during which time significant anomalies were observed. First, an initial period of rapid dissolution lasting a few minutes; second, an arrest or "plateau" region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effect of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured. The initial rate data were correlated by considering the rapid reaction to be due to the dissolution of surface oxidation products or the formation of an iron depleted surface layer. The data for the second slower reaction have been explained to be due

Jan 1, 1972

By Arash Habibi, Anna Cable, David Loring, Aleksandar D. Bugarski, Logan Ingalls, Calvin Rutter

The results of diesel particulate matter (DPM) monitoring were used by the underground mining industry to mitigate adverse effects of exposure to DPM. NIOSH Method 5040, currently used for ambient and personal exposure monitoring, does not provide needed real-time information. The objective of this study is to develop a methodology for continuous monitoring of DPM concentrations in an underground environment, founded on the application of the Dekati electrical particle sensor (DePS). The DePS, which measures concentrations of submicron aerosol in real time using a diffusion-charging sensor, was evaluated by comparing the results of the concurrent measurements with reference methods at several locations downstream of the diesel-powered equipment. The DePS results were found to correlate well to those obtained by reference methods. However, it was found that dependence of the response on the physical and chemical properties of aerosols necessitates sitespecific correlation factors for the targeted matrices. The site-specific factors for number and mass of diesel aerosols were derived using the results of concurrent measurements with TSI NanoScan, FLIR Airtec, and carbon analyses performed on the concurrently collected filter samples. The results showed that methodology based on compensated DePS measurements would be suitable for continuous monitoring of DPM in underground mining operations.

Dec 1, 2022

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016

By S. L. Crouch

The general term "coal mine burp" refers to the sudden and violent failure of in situ coal. Coal bumps occur in most countries where coal is worked by underground methods, and are related to both geological factors and mining tech¬niques. Although no single set of circumstances is solely responsible for causing coal bumps, it is generally agreed that at least one of five conditions is necessary in order for then to occur: 1,2,3,4 (1) the depth of cover exceeds 500-ft., (2) the overlying strata are relatively strong and stiff, (3) the coal is structurally strong, (4) the floor does not heave readily, and (5) the mining method produces high stresses over a large area of the seam. Except for the last, these conditions relate to geological factors that are impractical to control. Consequently, methods of controlling or minimizing the occurrence of coal bumps usually are concerned with mining techniques. Coal bumps have been successfully controlled by both longwall and 'yielding pillar' mining systems 4. The longwall system is particularly effective in controlling bumps, but does not eliminate them completely, especially in strong coal seams being worked at comparatively great depths, say in excess of 2000-ft.5. Under such conditions, auger drilling or water infusion often prove helpful 5,6. These techniques are used to destress or otherwise alter the mechanical properties of the coal in an attempt to shift the peak "abutment pressure" away from the immediate vicinity of the face. Under 'normal' conditions, however, it can be expected that the coal near the face will be crushed under the prevailing high stress conditions and that the peak abutment pressure will automatically be shifted into the solid coal. In this context, coal mine bumps can be characterized as unstable releases of energy associated with successive yielding of portions of the coal seam with progressive mining. Longwall and yielding pillar mining systems are effective in controlling coal bumps because they ordinarily do not allow the zone of peak abutment pressure to become 'surrounded' by destressed coal.

Jan 1, 1973

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980

By C. Garcia, A. Potulska, J. J. Opazo, T. Comi

"The Sierra Gorda SCM sulfide ore processing plant began commissioning in the third quarter of 2014. Located in the Atacama Desert in northern Chile, the project is an open pit mine and Copper-Molybdenum processing plant is one of the most highly-instrumented operations in the world. It is the first hard rock operation in Chile and the second in South America to utilize HPGR technology. It is a significant Molybdenum resource especially in the first five years and the Molybdenum separation plant is complex. Designed to process up to 60 million lbs. of fine Molybdenum per year, it uses the latest technology and equipment to ensure superior recovery and product quality. It also has gas handling and alarm systems to fulfil the Company’s vision of “Zero Harm”. This paper discusses the overall operation and issues relating to the concentrator start-up. These include a review of the mineral processing design, the unified process control center and management information systems, and the correlation of geological and metallurgical performance data (mine-to-mill) for use in anticipating and preparing for treatment of diverse ore deliveries. INTRODUCTION Sierra Gorda SCM is a joint venture partnership with KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining, and Sumitomo Corporation (Japan) operating in northern Chile. The Sierra Gorda open pit mine and Copper-Molybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, well-instrumented mine in Chile. This paper contains a general review of the project including geology and history. This was a very fast-track project going from greenfield site acquisition to mill start-up in 10 years. Highly-experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied. The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (see Figure 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km from the village of Sierra Gorda at an elevation of approximately 1,700 m above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic, and Escondida, to name a few."

Jan 1, 2015

By Thiemo Hagedorn, Gerhard Weissbach, Ralph Bergmann, Wilhelm J. Kogelmann

The objective of this unique method is to multiply the advance rate of conventional tunneling while improving both ground control and the safety of the crew. The high advance rate is achieved by concurrent rock excavation and installation of concrete lining at fully synchronized work phases. The novel TACHUSMATIC system consists of a high-production, robotic cutter boom, an automated slip form and continuous mucking and conveying. This novel system utilizes the inherent bearing capacity of the rock that is activated by a small, initial deformation. The supporting resistance is then provided both by the rock mass itself and the pumped in concrete lining. During the hardening of the concrete, the hydraulic cylinders of the TACHUSMATIC automatically apply the appropriate support resistance, thus providing safe ground control. This novel tunneling system is practically a fully automated, fail-safe NATM that does not require highly skilled engineers and crew. The TACHUSMATIC can be used for construction of circular, rectangular and horseshoe-shaped tunnels. When equipped with the Alpine Multi-Tool Miner (MTM) systems, the machine can work in a wide range of ground and rock conditions. The use of novel, diamond-tipped cutter bits (picks) will increase hard rock cutting capabilities and will significantly reduce pick consumption. Because of its moderate cost, the novel system is an economic alternative to conventional tunneling even at short drivages. A new installation is cost-effective for tunnels longer than 750 meters (2,500 ft.) At a typical tunneling project, the cost permeter is about 25% lower than with conventional methods.

Jan 1, 2003

By Langtry E. Lynd

The titanium dioxide pigment industry in the United States has always relied to varying degrees on imported titanium concentrates. Dependence on foreign ilmenite was especially high (generally over 85% of consumption) until 1942, when large-scale U.S. production of ilmenite began, and has since ranged from 12% to 47%. Rutile import reliance was generally in the 45% to 80% range until the early 1960's, when increased use in the chloride pigment process raised dependence on imported rutile to over 90% in most years since 1963. Import reliance of zircon, obtained almost entirely as a byproduct of titanium mineral production, has generally ranged from about 30% to 65% of consumption. This paper will examine the history of U.S. sources of these heavy mineral commodities, and will discuss the potential U.S. future supply in view of changing industrial uses and processes and the anticipated development of new heavy-mineral-sand processing operations, such as those at Richards Bay in the Republic of South Africa and in Sierra Leone.

Jan 1, 1978

Experimentation was performed on the flotation of apatite and dolomite separately using anionic collectors in the presence of Mycobacterium phlei. Also, the flotation of mixtures of dolomite and apatite in the presence of anionic collectors and in the absence and presence of the bacterium were studied. It was found that M.phlei functions as a depressant for both minerals. However, it functions as a better depressant for dolomite than for apatite. Experimentation was extended to two different Florida dolomitic phosphate rocks. In this investigation a concentrate grade of less than 1.0% MgO was achieved.

Jan 1, 1997

By Charles H. McGuirk

The Port of Conneaut, the largest bulk material handling and storage facility on the Great Lakes, is using the latest electronic and visual testing devices to augment and enhance its well established computerized preventive maintenance system. The results of this comprehensive program have been impressive. The remaining life of components can be accurately forcast, and replacement can be programmed around operations, resulting in a significant improvement in system availability and reduced costs for the dock operator and its customers.

Jan 1, 1983

By Keith A. Heasley

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence. Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents several case studies where a mechanics-based, boundary-element program is used to back-calculate the surface subsidence associated with various panels at several Northern Appalachian coal mines. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin scam or vein type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from the case studies in this paper demonstrate that the laminated model with calibrated properties can easily provide moderately accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies arc recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

Jan 1, 1999

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By G. Simmons

Santa Fe Pacific Gold Corporation (SFPGC) conducted pressure oxidation pilot plant studies at Hazen Research, Inc. on the Twin Creeks refractory carbonaceous gold ores during 1993 and 1994. Previous laboratory investigations demonstrated very good gold recoveries of 90 to 95%, using CIL cyanidation after batch pressure oxidation. However, results from the pilot plant showed that several ore types responded very poorly, with gold extractions of only 45 to 75%. Since these poor recoveries were unexpected, pilot plant testing was suspended for approximately four months while extensive research activities were conducted to determine the cause(s) and identify potential solutions. This paper describes the batch and pilot plant test results, the research activities that eventually identified the cause of the gold recovery problem, and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions.

Jan 1, 1997

By Edward S. Frohling

Va a ser discutida la información que se requiere para un estudio preliminar de viabilidad y la información adicional que se requiere para el estudio final de viabilidad de un nuevo depósito de mineral. El estudio preliminar de viabilidad se realiza con muy poca información y con un mínimo coste para el propietario. Sin embargo, el diseno del informe preliminar es similar al utilizado para el informe final. En este momento, se supone que el resultado del estudio preliminar es favorable y el propietario autoriza el estudio final de viabilidad a una compañía de ingeniería. Se describirá el tipo de organización para completar el estudio final de viabilidad. El informe final incluirá toda la información y datos relativos al nuevo depósito de mineral. La información presentada debe ser entendida lo mismo por el personal financiero que por el técnico.

Jan 1, 1982

By Jr. Moulton

Extractions of minerals from Searles Lake brines have taken place since 1873. Early operations were for borax and raw trona found on the surface, expanded after 1914 to include potash, salt cake, and soda ash. A new soda ash plant now in operation will double area production. The evaporite beds were formed by desiccation of Eastern Sierra runoff. The resulting series of brine-bearing salt beds supply the fluids necessary to feed the area chemical plants. Production methods include evaporation and crystallization for potash, borax, and salt cake; carbonation of brine to recover soda ash; and organic extraction of borax.

Jan 1, 1980

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical assessment of orebodies in the mining industry typically relies on bench-scale or lab-based characterization techniques. In this study, we investigate drone- and tripod-based field hyperspectral imaging as a potential addition to the geometallurgy toolkit in multiple applications. This pilot study tests hyperspectral imaging for largescale mineral mapping in and around the active Lisbon Valley copper mine, including natural exposures, previously producing U-V mines, highwalls, dumps, and leaching sites. Tests include different (supervised and unsupervised) mineral data classification methods, varying mineral spectral reference libraries, comparison with ground-truth geological and spectroscopic mapping and sampling, and integration with LiDAR data. The results show that hyperspectral scans can produce spatially registered maps of the distribution of different spectrally active mineral types over dumps, highwalls, leach pads, and natural outcrops. Clays, other phyllosilicates, carbonates, and sulfates showed up particularly well. The sensor was also able to distinguish dry from lixiviant-saturated areas and map different clay types on the leach pads, and shows promise for differentiating types and health of vegetation. These results suggest that hyperspectral imaging, if coupled with robust ground-truthing, can be a useful complement to existing geometallurgical techniques in the mining industry, such as geological mapping, blast hole sampling and automated mineralogy identifications, and handheld spectrometry. In particular, hyperspectral imaging has promise for mapping the distribution of acid-consuming minerals; mapping the distribution of swelling, sliming, and heap-blinding clays; and pinpointing problem areas on heap leach pad surfaces.

Feb 10, 2021

By C. E. Golson

The preparation of aggregates is a form of mineral processing which has been taken for granted for many years, mostly because of its lack of glamour when compared to the winning of metallic minerals from their ores. Many of the processes and equipment now used in the metallic mineral processing industries originated in the more prosaic preparation of aggregates. 'Their adaptation to metallurgical processes has led to developments both in their design, and in their use. Modern practice, has been so exacting in its demands that, in many cases, this improved technology is finding new applications in the very industry in which it originated the mineral aggregate industry, The low cost requirements, large tonnage capacities and complex specifications which govern the acceptability of its products have node modern aggregate processing a much different art than it was one or two generations ago. The basic conditions which govern the type and quality of mineral aggregates were presented in an addendum to a paper given at the San Francisco Meeting in 1959 by one of the authors.

Jan 1, 1961