Search Documents

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By Yonghong Qin, Songbo Ma, Qi Zhang, Peng Gao, Jianwen Yu

Herein, the coal-based reduction was proposed to utilize the ferronickel slag of Jingchuan company. An excellent index with metallization rate of 99.22%, iron grade of 77.91%, and iron recovery of 92.79% was obtained at carbon addition coefficient 2.0, reduction temperature 1573 K, reduction time 60 min, the particle size of coal and ferronickel slag − 2.0 mm, and CaO content 15%. The 2FeO·SiO2 was reduced to Fe and SiO2 with the increase of temperature. The CaO could promote the reduction of iron oxide. Most of the sulfides (Fe, Cu, Co, and Ni) in the sulfonium were reduced to metal. The reduction degree increased with the reduction time and reduction temperature. The higher reduction temperature represented the higher peak value of reduction rate and the shorter time of reaching the peak value. The isothermal reduction process included three stages: early stage, middle stage, and late stage. The mechanism function were f(α) = 1/2(1 − α)3, f(α) = 3/2(1 − α)4/3[(1 − α)−1/3 − 1]− 1, and f(α) = 4(1 − α)[− ln(1 − α)]3/4, respectively. The activation energy of three stages was 183.498 kJ·mol−1, 420.077 kJ·mol−1, and 656.619 kJ·mol−1, respectively.

May 24, 2022

By Haitao Wang, Shen Wang, Dongyin Li, Yongjia Xu, Jinzhao Liu, Xiangjun Chen

The safe and efficient driving of the roadway along the gob is becoming an increasing challenge due to the influence of the integrity and bearing capacity of the side coal and rock mass in the gob under the roof cutting mining mode. The mechanism of protection of the gob-side roadway is shown by modeling the influence of roof cutting and the application of a destress technique on the lateral coal and rock mass zones. The distribution characteristics of stress, displacement, and fracture in the overburden are analyzed by numerical simulation method under the three working conditions. The results indicate (1) construction of row holes and blasting can form artificial structure’s fracture plane above the roadway, which can effectively cut the connection of overburden. The artificial structure’s fracture plane decreases the peak value of the lateral coal body’s support pressure. The peak point and the critical location of the stress reduction area are both transferred to the deep part at the same time, providing adequate space for the gob-side roadway. (2) The stress arch foot in the lateral rock mass rises to the rock layer at the bottom of the roof cutting plane after top cutting, as does the high-pressure area of deviator stress. The fracture plane prevents lateral coal and rock mass instability and limits the negative effects of roof deformation above the gob-side roadway. (3) The triangle slip fracture zone moves to over the roof cutting drilling zone due to the fracture plane, showing a high position compared to its original zone.

Jul 11, 2023

By D. R. Babich, E. R. Bauer

Noise-Induced Hearing Loss (NIHL) continues to be a concern of the mining industry. A new noise standard (30 CFR, Part 62) is aimed at reducing NIHL in mining through engineering and administrative noise controls. However, the difficulty and expense of implementing engineering controls can make administrative controls an attractive alternative for reducing worker noise exposure. Over the last three years, the National Institute for Occupational Safety and Health (NIOSH) has conducted worker noise exposure surveys in underground and surface coal mines and coal preparation plants. The surveys revealed numerous possible administrative controls and an approach to implementation and analysis. The surveys have shown that worker dosimetry, time-motion studies, and equipment noise profiling are important aspects of effectively utilizing administrative controls. A description of the approach for selecting, implementing, and evaluating administrative controls, and a list of administrative controls, are reported.

Jan 1, 2004

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

By John F. Shea

When Dick Robbins asked me to give a keynote address, I felt it might be in order to review some of the practices and techniques used in tunneling and work up to some of the concepts now used to mine and construct tunnels. Needless to say, there have been many changes in tunneling technology and also many changes in the Safety Codes controling them. An example of this latter change was the fact that in 1931, my father excavated the Owyhee Tunnel No.5 with gas locomotives. He was able to do it because there was no natural gas in the rock and the ventilation system was designed to free the tunnel atmosphere from powder and exhaust fumes. Today OSHA rules would never permit gas locomotives underground, although there were no incidents on this particular project. One of my first tunnels, as Project Manager, was the Clear Creek Tunnel for the Bureau of Reclamation. Our method of handling muck was the Conway Muckers. This unit was a valuable improvement to the hand mucking of previous generations. The Conway was also used in our Navajo Project, in New Mexico. Unlike the Clear Creek project, where water was one of our main problems - up to 7,200 gallons per minute, at a pressure of 395 pounds per square inch - in the Navajo Tunnel, we had a mixed face which caused a major problem with our support system. In one of the Navajo Tunnels, there was a major cave-in, when the squeezing shale came in during an attempt to strengthen the support system. Although moving shale was not a constant problem, there were areas where the shale was five to six feet above the spring line.

Jan 1, 1976

The mining industry is an important economical factor in Vietnam. Mining is presently being conducted at about 60 locations and at over 1000 mines. Petroleum extraction and coal mining are the most important parts of industry though metals such as zinc, tin, chromites, iron are also extracted. Last year the sector produced 20 million tons of crude oil, 26 million tons of coal and 500,000 tons of apatite. In particular, Vietnam is one of the world?s largest producers of anthracite, and it is one of the top producers of ilmenite and zircon in the Asia-Pacific region. The government intends to increase the mining production on all levels, however, at present one can observe adverse impacts of the mining activities on the natural environment such as insufficient waste dump rehabilitation, occurrence of acid mine drainage, mining subsidence and emissions as well as lack of appropriate water treatment facilities. This paper describes the current mining situation, future perspectives, the major environmental challenges of the country and approaches to solve these problems. Particular emphasis will be given to the research project ?RAME ? Research Association on Mining and Environment in Vietnam?, a venture carried out by universities, research centres and industry. This project is worked out in collaboration with the national Vietnamese coal and industrial minerals company VINACOMIN.

Jan 1, 2006

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof (XP) enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4) air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway (TR). Researchers at the National Institute for Occupational Safety and Health (NIOSH) measured TR pressures of lithiumiron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 294 bar (4260 psia) of pressure during a TR, far exceeding minimum pressure containment specifications for conventional XP enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce TR pressures to levels below that expected for CH4-air ignitions. Measured TR temperatures were below the minimum autoignition temperature of CH4-air.

Nov 6, 2020

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using either a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion, and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent.

Jan 1, 1990

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, demand for coal exceeds its countrywide supply, despite its natural abundance, due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98% of total raw coal production within the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an eco-friendly manner, especially in the populated areas adjacent to the mining zone and, hence, require restricted blasting operations. It eliminates blast hole drilling, blasting, and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks. This paper encompasses the applicability, advantages, constructional features, and performance assessment models for each working mode of a surface miner. The current paper discusses the correlation between coal production and key productivity indicators, namely, machine shift-time, pick, and diesel consumption of surface miner in three different geo-mining conditions. Furthermore, relationships between machine shift-time, pick, and diesel consumption of surface miner and coal production were evaluated through bivariate regression analyses along with their coefficient of determination. These key productivity indicators of surface miner follow polynomial relationships with coal production on a daily and monthly basis, having Pearson correlation values from 0.774 to 0.907 and coefficient of determination, from 0.664 to 0.909 in opencast coal mines.

Jan 20, 2023

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By A. Anttila

The grinding mill is probably the most common unit operation used in mineral processing. There is, however, much which can still be done in the way of optimization. This paper discusses the results of a well controlled pilot scale test in which the performance of a tumbling mill with a conventional rubber lining equipped with lifter bars is compared to that with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14 percent more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case the -20 mm ball charge required 26 percent less grinding energy than one with a -30 mm ball charge. The energy savings can. in most cases, be converted to increased capacity. The wear of the grinding media is difficult to assess over a short period test but the results suggest it is somewhat less when a smooth lining is used. The wear of the linings has not been included in this study but it is generally accepted that the use of the magnetic lining reduces the lining costs dramatically. Computer simulation using the Millsoft code, developed by Mishra e.a. confirms and explains the increased effectiveness of comminution when smooth lining and smaller grinding balls are used.

Jan 1, 1998

In its largest product launch in company history, Cummins Engines welcomed more than 200 customers, vendors and media to witness the unveiling of its new QSK95 engine at its Seymour Engine Plant in Seymour, IN on Nov. 1. It took the efforts of 150 engineers to design the QSK95 and more than $100 million in investments to establish a new production line and test facility at Cummins? Seymour Engine plant. The result of these efforts is a new platform of engines that Cummins says will provide as much as 2,983 kW (4,000 hp) and will be the most powerful, high-speed diesel engine ever built.

Jan 1, 2012

By G. Deschênes

In an earlier study (Deschênes et al., 2009), gold and silver were shown to be efficiently extracted from samples taken from the Kupol Mine in Russia using lead nitrate in a cyanide leach system. In the current study, a com-parison of the technical and economic merits of a new technology called CANMET enhanced leaching process (CELP) was made with the cyanidation/acidification-volatilization-recycling (AVR) process using eight metal-lurgical variability samples, as well as a large composite sample, which was to represent the initial two years of Kupol mill feed. The composite sample leach feed assayed 33.4 g/t Au and 289 g/t Ag. The metallurgical results from the large composite sample demonstrated that CELP produced very similar gold and slightly higher silver leach extractions compared to the conventional cyanidation/AVR leach conditions at 1/2 the cyanide concentra-tion (1,000 ppm NaCN in CELP vs. 2,000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton was approximately the same for the two technologies (total cost of CELP with the use of Merrill-Crowe at $46.48/t, with cyanidation/AVR at $46.13/t). However, the implementation of CELP would eliminate a capital expenditure of approximately $5 million for an AVR system based on a 2005 feasibility level cost estimate. Eight variability samples used to confirm the composite sample results showed that, on average, the gold leach extractions with CELP and the conventional leach conditions were very similar, but the average silver leach extraction was 2.1% higher for CELP. Furthermore, CELP silver leach extraction was 4.6% higher on average compared to conventional cyanidation for the four mid-grade variability samples evaluated. The decision was made to remove AVR cyanide recovery from the flowsheet and implement CELP at Kupol. The ability to use the conventional leach equipment with CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2010

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997