Search Documents

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984

By M. P. Roy, P. K. Singh, A. K. Mishra, Ashish K. Vishwakarma, Vivek K. Himanshu

Ground vibration is one of the major hazards produced by rock-blasting operation. The accurate prediction of vibration is necessary for designing controlled blasting parameters. The existing vibration predictors consider maximum explosive charge weight per delay and distance as the parameters responsible for ground vibration. These predictors are based on the assumption that the geometrical parameters of the blast will be constant for a site. However, the mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, the other blast design parameters will also have an impact on ground vibration intensity. A principal component analysis is a dimension reduction technique. This technique along with multivariate logarithmic regression has been used in this paper to predict the ground vibration. The technique has classified the blast design parameters into four principal components. The regression with the scores from these principal components has been carried out. The evaluation of the model performance of predictors along with the existing empirical predictors has been carried out using R2 and RMSE values. The evaluation suggests that the predictor with logarithmic regression followed by principal component analysis gives better performance with respect to the existing empirical predictors.

Jul 30, 2022

By J. P. Allen

Cobalt, nickel, and manganese can be recovered quickly, cleanly, and selectively from cobalt-rich manganese crust by leaching in dilute acid solutions in the presence of hydrogen peroxide. Common selective precipitation methods can then be used to recover these metals from the leach liquor. The leaching reaction produces only oxygen as a byproduct, and the waste residue from leaching was tested and found to be non-hazardous under existing EPA specifications. The leaching process is effective in either fresh water or seawater. This research is a part of the Bureau of Mines program to identify the mineral resources of the Exclusive Economic Zone and devise methods for recovering their valuable components.

Jan 1, 1990

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By L. Zhou, A. Martikainen, G. Goodman

Continuous airflow monitoring can improve the safety of the underground work force by ensuring the uninterrupted and controlled distribution of mine ventilation to all working areas. Air velocity measurements vary significantly and can change rapidly depending on the exact measurement location and, in particular, due to the presence of obstructions in the air stream. Air velocity must be measured at locations away from obstructions to avoid the vortices and eddies that can produce inaccurate readings. Further, an uninterrupted measurement path cannot always be guaranteed when using continuous airflow monitors due to the presence of nearby equipment, personnel, roof falls and rib rolls. Effective use of these devices requires selection of a minimum distance from an obstacle, such that an air velocity measurement can be made but not affected by the presence of that obstacle. This paper investigates the impacts of an obstruction on the behavior of downstream airflow using a numerical CFD model calibrated with experimental test results from underground testing. Factors including entry size, obstruction size and the inlet or incident velocity are examined for their effects on the distributions of airflow around an obstruction. A relationship is developed between the minimum measurement distance and the hydraulic diameters of the entry and the obstruction. A final analysis considers the impacts of continuous monitor location on the accuracy of velocity measurements and on the application of minimum measurement distance guidelines.

Jan 1, 2012

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By S. Cotten

The concept for a Mine Escape Vehicle (MEV) is motivated by the desire to enable personnel to evacuate a mine rapidly as the first and most desirable response to any underground emergency. Under a NIOSH contract, Raytheon UTD developed a conceptual design for a vehicle that coal miners could use to facilitate their rapid exit from an underground coal mine in the case of emergency, including fire or explosion. The vehicle requirements include the capacity to provide life support functions for a number of miners, operate in an oxygen deficient, low or no visibility atmosphere, and travel at speeds faster than miners can walk out of the mine. To develop the MEV concept, three primary tasks were identified and executed. The first task focused on developing a realistic concept of operations (CONOPS) and associated high level vehicle requirements. The second task identified and evaluated currently available equipment and technologies that could be applied to address the CONOPS. The final task developed a design concept that integrated the identified components for the five (5) MEV sub-systems to provide the foundation for future detailed engineering design and prototype construction. The resulting MEV design concept is centered upon retrofitting existing mine personnel carrier chasses with available, mine-worthy equipment capable of addressing the MEV requirements. This approach offers a practical and economic avenue to prototype development and delivery with minimum lead-time and risk. Furthermore, by integrating familiar and available equipment into the design and CONOPS, the resulting Mine Escape Vehicles should also be more readily accepted by the mining industry.

Jan 1, 2010

By A. T. Iannacchione

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels. 1 Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m (26.5 ft) above the miner's head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roof beam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By Serhat Özdemir, Derya Öz Aksoy, Pınar Aytar Çelik, Ahmet Çabuk, Sabiha Koca, Hüseyin Koca

In carbonate flotation, oleate has been used for many years as a collector in industrial scale. Compared to sulfide minerals, the flotation of carbonate minerals requires more collector consumption and has lower yield and selectivity. It has been previously shown that surfactin provides higher yields in smaller amounts than oleate in the bioflotation of calcite as one of the carbonate minerals. In this study, the usability of surfactin as a flotation collector for magnesite was investigated. For this purpose, the adsorption of surfactin on the magnesite surface was inspected with analyses such as FTIR, SEM–EDS, contact angle, and zeta potential measurements. In addition, the effect of surfactin on the surface tension of water was also revealed. The same analyses were also performed for oleate as a reference point. All flotation experiments were performed without optimizing with both collectors. FTIR results showed that the surfactin, like oleate, was chemically adsorbed on the magnesite surface. Surface tension analyses showed that the surface tension of water decreased to approximately 32 N m− 1 at 10− 4 M oleate concentration, and this value decreased to below 25 N m− 1 at the same surfactin concentration. According to contact angle measurement results, the contact angle of magnesite was 85° after the surfactin adsorption of 2 × 10− 4 M concentration, while this value remained at 46° for oleate. Finally, according to flotation experiments, high temperatures and high collector dosages are necessary for acceptable flotation recovery with oleate, yet surfactin can produce the desired result at ambient temperatures and lower collector amounts.

Dec 13, 2022

By Y. V. Vasylchuk

An algorithm is presented for optimizing the classification of surface mine material subject to excavating constraints. High-resolution, expected-profit models are optimized to classification maps subject to site-specific excavating constraints. This optimization problem defies traditional closed-form analytical solutions. A practical heuristic algorithm quickly determines the optimum final destination for material subject to realistic selectivity constraints. The expected profit could be calculated from an estimated model if the value calculations are all linear; otherwise, simulation could be used. In both cases, a single expected profit for all destinations on a high-resolution grid is the starting point for dig limits optimization. Maximizing expected profit in a risk-neutral manner is correct given the repeated nature of grade-control decisions over relatively short timeframes.

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011

By John A. L. Campbell

Surface dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or imporve a surface dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and flocculation. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established (1). These data will be presented at a latter date.

Jan 1, 1969

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By S. -Y. Hwang

An ongoing problem for industry in Korea is effective removal of heavy metals from and safe disposal of spent power plant fly ash. This research endeavor attempts to develop selective separation of Ni from leach liquor using a selective chemical precipitation method. The research was conducted by changing two variables, the pH and the concentration of ions in solution. The effect of other ions present in the system on the separation efficiency of Ni species was also investigated by adjusting OH and NH3 concentrations. In the pH range of 7-9, the chemical precipitation method produced a high yield of Ni by precipitation from the fly ash leach liquor.

Jan 1, 2010

By George W. Bain

Deposits of metals in only slightly disturbed strata have been attributed to sedimentation processes contemporary with deposition of the strata. Recently this origin has been extended' to a greater variety' of deposits and local enrichment has been attributed to selective remobilization of metallic minerals in the host stratum. Effects attending metallization and deformation, and exact age' of the metallization are compiled to establish the sequence of events in ore deposit histories in order to clarify importance of remobilization within a formation relative to introduction from an outside source into an fav¬orable host. The pertinence respectively of deposit; origin and geometry to the work of the mining geologist is reviewed. Dwarf faunas in the Clinton iron ore, Tully pyrite bed and Rammelsberg deposit, indicate abnormal metal ions in the sedimentary environment. Slight¬ly disturbed strata are host rocks in the Swedish Kolm, Timna, Kupferschieffer, and White Pine deposit; the latter two have ore only in conjunction with tectonic structures.

Jan 1, 1966

By Kelly Sands

"Mitigation may be considered a hurdle when it comes to environmental permitting. For complex projects with site specific mitigation plans, the time to devise those plans and get them approved can be a long and costly endeavor. However, mitigation options are expanding and the mitigation banking industry has grown tremendously over the last two decades, helping projects move forward with less debate. Mining companies are recognizing the value that mitigation banks provide in helping to shore up project timelines and costs. Where possible, companies are taking advantage of the opportunities to buy credits from thirdparty providers offering mitigation bank credits. In some instances, mining companies are taking matters into their own hands by establishing mitigation banks to realize their own mitigation freedom. That can have its advantages and disadvantages, as discussed below. All in all, the expansion of mitigation options has streamlined the permitting process, introduced flexibility, improved project permitting timelines and loosened the permitting girdle.Compensatory mitigationCompensatory mitigation involves actions taken to offset unavoidable adverse impacts to wetlands, streams and other aquatic resources and authorized by Clean Water Act section 404 permits and other permits. As such, compensatory mitigation is a critical tool in helping the federal government meet the longstanding national goal of ‘‘no net loss’’ of Waters of the U.S., both in acreage and function.Section 314 of the National Defense Authorization Act for Fiscal Year 2004 required the Secretary of the Army, acting through the Chief of Engineers, to issue regulations “establishing performance standards and criteria for the use, consistent with Section 404 of the Clean Water Act, of on-site, offsite, and in-lieu fee mitigation and mitigation banking.” The provision also required that those regulations ‘‘maximize available credits and opportunities for mitigation, provide flexibility for regional variations in wetland conditions, functions and values, and apply equivalent standards and criteria to each type of compensatory mitigation’’ (73 FR 19595). The result was the Final Rule on Compensatory Mitigation for Losses of Aquatic Resources issued in 2008 (33 CFR Parts 325 and 332).”"

Jan 6, 2017

By B. Pina

The conversion of maf coal to pyridine solubles and gas was investigated in a microautoclave batch reactor for two Kentucky washed coal samples (Ky. #9 and Ky. #11). Solvent hydrogen donor strength was controlled by the tetralin content of a mixed 1-methyl naphthalene-tetralin solvent. Primary liquefaction conversions greater than 90% in 10 minutes of reaction time at 427°C were achieved in liquefaction solvents with moderate hydrogen-donor strength (circa 40% tetralin). A modified irreversible first order rate expression, containing a parameter (a) to account for the intrinsic reactives of the maf coal, described the experimental kinetic data rather well. The integrated form of this rate expression is -k1e x = a (a- ß)e (eq. 1) Parameter ß in equation (I) is the pyridine solubility of the starting maf feed coal, x is the primary liquefaction fractional number of conversion, k1 is the specific reaction velocity constant and ? is reaction time. Primary liquefaction rate was found to be quite temperature sensitive and independent of coal when a liquefaction solvent containing 40% or more tetralin was employed. Primary liquefaction rate appears to depend on liquefaction solvent hydrogen donor strength for solvents containing = 40 wt.% tetralin. The intrinsic reactives in the maf feed coal or a appear to depend mainly on the inertinite group maceral content of the coal for the two coals studied in liquefaction solvents containing 3 40wt.% tetralin. In contrast, a appears to decrease in liquefaction solvents of low donor strength., i.e; solvents with less than 40wt.% tetralin.

Jan 1, 1984

By W. C. Lacy

Traditionally Australia has been a leader in underground mining methods with world standards being established at Mount Isa, Broken Hill, Kalgoorlie, and Mount Lyell. With decline in higher-grade reserves and discovery of a multitude of near-surface oxide gold de-posits attention has shifted to bulk mining of low-grade gold ores by open pit methods, heap leaching and activated carbon recovery of gold values. The paper examines historical change in mining philosophy and the economic effects of isolation.

Jan 1, 1993