Search Documents

By L. J. Blatnica

Throughout the 1980's the tem Mine-Wide Monitoring System has had various meanings for manufacturers of these systems and underground mine operators alike. System suppliers had visions of grandeur in the early 80's as they envisioned each mine, that has more than a single section, installing a computer based monitoring system to provide surveillance, control and documentation of the entire mining operation, including everything from a single heat detector to the weekly payroll. In a few cases this may have become reality but the truth is these systems have quietly become a steady but unspectacular workbase for the modern mining industry of the 1990's. As it exists today the total market for underground monitoring systems may not exceed $10 million annually. Suppliers have lowered their expectations of the dollar value of this particular market. Some were entering a new market because of experience with computer based data acquisition systems. Others had been active in the mining industry for years with more traditional equipment (communication systems, methane monitors, safety equipment, etc.) and decided to become involved with Mine-Wide Monitoring Systems.

Jan 1, 1990

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Project-scale decisions in surface mining operations rely on the optimization and subsequent evaluation of pit limits. This process ignores the ability for mine plans to adapt as more information is gathered. Stochastic methods, which consider uncertainty in the pit optimization, generally act to refine the boundaries of the pit on a fine scale. This paper extends uncertainty-based methods to consider unique scenarios through a clustering of the realizations that are being optimized. This results in the generation of multiple sets of similar realizations. A separate pit is optimized on each set of realizations, resulting in the production of a series of planning scenarios. This accounts for the adaptability of mine planning as more information is gained. A decision-making framework is then applied to the resulting scenario plans to select the optimal choice. The improvements stem from the joint uncertainty considered when realizations are grouped that is not considered when the probability of a block being in any optimized pit is considered. Mining operations today can benefit from considering additional planning options as identified and evaluated in this workflow.

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By R. Brown, A. J. S. Spearing, M. Treinen, M. Theisinger

The mining and use of coal creates a significant amount of waste material that needs to be safely disposed of. It is likely that in the medium term, the Environmental Protection Agency (EPA) in the U.S. will categorize all such products as a new category – special waste. This would make the materials subject to many of the requirements for handling toxic waste, which will complicate the disposal of such products and significantly increase the disposal costs. Underground disposal would, therefore, seem to be the obvious solution, especially if the placed material can have low or no permeability, so that water table pollution does not present a serious long-term issue after placement. Significant additional advantages could be derived from this backfilling, including the reduction or elimination of surface subsidence, increased extraction, reduced surface waste disposal footprint and the elimination of explosion-proof seals in worked out areas. The research using a specific coal waste product as a typical example proved that the method of placing the backfill at a high density with low permeability is technically viable, but it must be made more cost effective and the other potential benefits quantified and costed in order to present a true comparison.

Jan 1, 2010

By R. V. Ramani, C. J. Bise

INTRODUCTION Classification of coal seams as thin, medium, and thick is both subjective and relative and is more a reflection of the statistical mode of the thicknesses en- countered in a mining region. A geological factor more precisely understood as defined than thickness is the inclination of the seams to the horizontal, commonly referred to as the pitch or the dip of the seam. Thick and steeply pitching seams present far more challenges to the ingenuity of the mining men to devise methods for their extraction than the thick and less steeply inclined ones. In a marginal case, where a thick coal seam may be minable by surface or underground methods, the decision bears a close relationship to the technological developments in the mining scene. Near surface thick coal seams are a special gift of nature and are not as wide- spread as the ones that call for the application of under- ground methods. Recent advancements in surface mining equipment have made it possible to surface mine to great depths. Stripping ratios of 30: 1 (cu yd of over- burden removed per ton of coal) have been achieved. The extraction of thick seams which preclude the use of surface methods is the concern of this chapter. Specifically, the objective here is to outline the special technological factors in underground mining of thick coal seams and to illustrate through several case histories the methods that are practiced in the North American continent. For the purposes of this chapter, a thick seam is defined as one which is not readily minable with currently available equipment without modifications to the extraction method or the equipment. At the present time, a thickness of 4.8 m (16 ft) can be considered as the lower limit, although developments in equipment and methods can be expected to push this limit upwards. The data for the case histories were collected from two extended mine visits in 1975 and 1978, and from other published accounts of the mines visited. Reference is drawn particularly to reports by Bise, Ramani, and Stefanko (1976) and Rarnani and Kenzy (1979). THICK SEAM MINING METHODS The various methods of mining thick seams can generally be grouped into three major categories: full face methods, where the entire thickness of the seam is re- covered in a single pass; slicing methods, where the seam is extracted to its full thickness by horizontal or inclined slices either in an ascending or descending order; and caving methods, where the seam is undercut and the en- tire coal seam is recovered by caving the top coal into the excavated cut, or some variations of the basic sub- level caving method. As shown in Table 1, in each of these methods, the coal is removed by either room-and-pillar or longwall methods. Hydraulic mining and transport of the coal in open flumes or in pipelines are also practiced. Addition- ally, the void created by the removal of coal may be filled with a packing material (stowing) except in the caving methods. The pitch (dip) of the seam, particularly when it is greater than 0.26 rad (150), imposes severe operational limitations on mobile equipment. A more detailed general discussion of the methods can be found in Bise et al. (1976) and Vorobjev and Deshmukh (1964). Specific discussion on the many variations of the three basic methods can be found in the papers presented at the international symposia that were held in

Jan 1, 1982

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968

By C. A. Young

Cyanide is a toxic species that is found predominantly in industrial effluents generated by metallurgical operations. Cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent accidental spills. Various methods of cyanide remediation by separation and oxidation, including photolytic advanced-oxidation processes, are therefore reviewed. Reaction mechanisms are presented throughout the paper. The methods are compared in regards to their effectiveness in treating various cyanide species: free cyanide, thiocyanate, weak-acid dissociables, and strong-acid dissociables.

Jan 1, 1996

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By T. N. Andersen

The history of gold and silver analyses shows an interesting duality. On one hand, classical chemical and instrumental methods have evolved to meet changing needs, but on the other hand, the age-old and somewhat empirical fire assay has remained a popular tool. Inasmuch as gold and silver generally have been present in ores at low concentra¬tions, methods have been challenged by a need for sensitivity and selectivity coupled with reasonable assay time. A progressive increase in the importance of low grade materials as ore sources has led to the need for improved methods. Assays of these materials are required for process control and accounting in operating plants as well as for guiding research and development activities. The analytical response to these needs is evidenced by numerous reviews published through 1977-¬e.g., cf Kolthoff and Elving (1966), Beamish and Van Loon (1966, 1972, and 1977), Young (1971) , Mallett (1970), and Sen Gupta (1973). In this paper we present a brief sketch of the history and status of various gold and silver methods. A more detailed summary of atomic absorption spectroscopy (AAS) is Given, as this method has gained in popularity more than other assay methods. AAS methods currently in use are summarized and discussed briefly. This paper is not meant to be a detailed review, as are the above mentioned publications. Rather, we borrow from those works and more recent papers to report trends in gold and silver analyses (particularly in AAS). Also, we discuss some selected poten¬tial problems, and problems that have been experienced by this laboratory.

Jan 1, 1981

By Chee Theng

"Mineral processors know you can put in the best technology in the world but it won’t work optimally without the support of the operators. Conversely, you may have complete operator support but won’t get top results without the right technology. When the two come together, the returns can be phenomenal.The first day of talks at the 68th Annual Colorado MPD Conference, held April 26-28 at The Broadmoor in Colorado Springs, covered the ground on these industry wisdoms.Coming together as a team“Think of the people, not just the lab and the numbers. That makes all the difference,” said Dee Kippers, of FMI Henderson Mine, in her talk on “Process optimization during a market downturn (A Moly MacGyver story).” Kippers told an entertaining story of the journey she and her team took in tackling the issue of an annual spike in iron content in the product at Freeport- McMoRan’s Henderson primary molybdenum mine near Empire, CO.As the metallurgists tried one thing after another — cranking up the iron depressant, adjusting pH with sodium hydroxide and hydrated lime, modifying reagent levels — Kippers found that when she shared her results with the operators, communicated with them on what she was doing and got their input, they were more willing to work with her, and more understanding and supportive of her efforts.The results make the case for getting people on board and coming together as a team. The cost savings from their optimization efforts, with little capital investment, have been “enough to cover the annual salaries of our metallurgy department and then some,” Kippers said.Considering the environmentDavid Lemieux, of Dundee Sustainable Technologies (DST), talked next on “Cyanidefree process for gold extraction,” presenting the results obtained from a demonstration campaign of the company’s novel chlorination process for gold extraction and associated arsenic stabilization process. Developed at an investment cost of C$35 million, they are ready for commercialization, having been demonstrated on the laboratory, pilot and demonstration scales.The DST process is differentiated from the Plattner chlorination process, which was in use from 1851 to 1916, by moderate process conditions of atmospheric pressure and ambient temperature — the result of using sodium hypochlorite solution, or bleach, instead of direct injection of chlorine gas — and new, cheaper materials of construction, such as polymers, plastics, fiberreinforced plastics and Teflon, resulting in lower capital and operating expenditures."

Jan 7, 2018

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

By Jake Gibson

"As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action toward decreasing greenhouse gas (GHG) and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel, accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery-powered ac systems and diesel-fired heaters, going noidle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, standalone mobile equipment HVAC.The history of GHGs and climate changeIn 1896, Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960s, Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Fig.1).In 1988, the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgment of a rising global annual temperature. The IPCC consists of more than 2,500 scientific and technical experts from more than 60 countries. Because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998, requiring all participating countries to reduce their GHG emissions by at least 5 percent from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States). In 2002, the Bush administration announced a policy for climate change relying on domestic, voluntary actions to reduce the "greenhouse gas intensity" of the United States economy by 18 percent by 2012. The U.S. still attends the Kyoto conference of parties (COPs) but does not participate in negotiations, as it is not bound by its terms."

Jan 1, 2014

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005