Search Documents

By Michael J. Miller

In the design of a modem mill, a stockpile storage system for raw and/or semi-processed ore has become almost indispensable. This paper discusses the benefits of such stockpile storage as well as the various types of belt conveyor stockpiling units available. Particular attention is given to large radial stackers since they offer the greatest flexibility. Stacker control systems and accessory equipment are briefly discussed. Various alternative reclaiming arrangements for stockpiles are reviewed and a discussion of the advantages and drawbacks of each arrangement is included.

Jan 1, 1979

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By LeRoy D. Loy

To facilitate effective land reclamation and comply with existing state regulations, surface coal mine operators have in recent years adopted new mining techniques and equipment utilization for steep-terrain mining. In contrast to direct spoiling with draglines or shovels, these new mining methods require some form of overburden haulage from the excavation face to the point of reclamation. Although current mining methodologies such as Block-Cut, Modified Block-Cut, and Mountaintop Removal with Head-of-Hollow Fills have proven effective in achieving reclamation objectives, some production problems have resulted from pit congestion and excessive equipment delays. Recognizing this problem, the United States Bureau of Mines contracted Skelly and Loy to design innovative mining concepts utilizing conveyor haulage in place of trucks, loaders, dozers and scrapers. Project objectives required definition of current bottlenecks and development of mining systems to: alleviate bottlenecks; increase production potential; facilitate additional resource recovery; enhance reclamation; reduce safety hazards; and improve mining economics. Successful completion of project goals within a four year program involves systematic implementation of the following separate work phases: 1) Develop Concepts for Block-Cut Mining Systems; 2) Determine the Economic and Technical Feasibility of Concepts; 3) Prepare Detailed Design and Specifications of Concepts; and 4) Prepare Specifications for Conducting Field Tests of the Most Promising Concepts. At the time of this publication, Phases 1 and 2 are finalized with Phase 3 efforts well underway.

Jan 1, 1977

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

By Sara Swiokla Korsikas, Toren Olson, Amado Guzman, Yuri O. Zepeda P

Ore agglomeration has been used as part of the heap leaching process for the last 40 years. However, industrial experience shows that the lack of a universal agglomeration standard has limited the benefits of this, otherwise, valuable unit process. The more complex the ore, in terms of the nature and relative abundance of fines (<74 μm), the more important that the agglomeration product satisfies some minimal requirements. This paper presents an agglomeration scale that identifies the quality standards for agglomerates and documents the resulting mechanical, physical, and hydraulic (hydrodynamic) behavior associated with each level on the agglomeration scale. The hydrodynamic properties of an agglomeration product are critical for the proper design of a leaching operation and, as shown in this paper, can be used to select the optimal pretreatment method for a given ore sample. Agglomeration as a unit process not only allows better conditioning of the hydrodynamic behavior of the ore but also creates an opportunity for optimized delivery of reagents to kick-start the leaching process which may ultimately improve the economic performance of leaching. Industrial case data is used to demonstrate the shortfalls associated with low-quality agglomeration and the benefits of improved agglomeration which range from enhanced porous structure (better percolation and drainage characteristics) to better metallurgical response (faster kinetics and higher metal recovery). Proper agglomeration has been used to render otherwise untreatable ores into valuable leaching resources.

Feb 9, 2024

By W. H. Schiffbauer

The U. S. Bureau of Mines has been investigating methods and technology that, when applied to existing continuous coal mining machines, may improve production and safety. Toward those goals, a microcomputer network has been designed that provides automated control and monitoring of all mining machine systems using a single twisted pair cable (two conductor stranded wire twisted together to provide a level of noise rejection). The network also provides -connections for intelligent sensors and systems for navigation and diagnostics. The flexibility of the network is demonstrated in that features can be added and removed without redesigning the whole system. A general description of the network&apos;s integration to a Joy&apos; 16CM, Joy 14CM, Jeffrey 102, and a custom built auger machine is provided. The microcomputer networks for the Joy 16CM and the Jeffrey 102 have been installed onboard the mining machines and have been extensively tested at the Bureau of Mines test facility. The Jeffrey 102 system has also been tested in an actual highwall coal seam. Both systems have performed satisfactorily. The microcomputer networks for the Joy 14CM and the Auger Miner have been tested and await installation on the respective machines.

Jan 1, 1990

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques have been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

Feb 23, 2014

By J. MCGUIRE, E. J. Haas, B. Demich

Near misses can enhance awareness of the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, the value of these reports and how they influence subsequent actions or controls to reduce on-the-job risks are unclear. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. The analysis provides insight into ways that risk-communication and management programs can be improved to reengage workers and their situational awareness on the job.

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By J. G. Groppo, A. E. Bland, B. K. Parekh, W. F. Stotts

Many coal preparation plants discard fine coal (generally minus 100 mesh) because it is difficult to beneficiate economically. At the Kentucky Energy Cabinet Laboratory (KECL), the waste streams from several Kentucky preparation plants were evaluated for cleaning with counter-current column flotation. A series of performance evaluations were conducted using a 0.05 m (2 in.) internal diameter (I.D.) 7.9 m (26 ft.) high laboratory column. The objectives of these tests were to assess the performance in terms of recovery and percent ash in clean coal and to optimize the operating parameters relative to combustible recovery and grade. Refuse streams containing 30-50 percent ash were upgraded to 2-8 percent ash with Btu recoveries of nearly 90 percent. A pilot scale column flotation cell was installed at the Bell County Coal preparation plant. This pilot plant utilized a 5.79 m (19 ft.) high and 0.15 m (6 in.) I.D. column to verify the performance data of the 0.05 m (2 in.) I.D. column for two different waste streams. Performance evaluation and pilot plant testing results related to scale-up are discussed.

Jan 1, 1988

By Scott L. Burrill

In the past 100 years in the mining industry, many references are made to the "Widow Makers", &apos;Miners Con" and many other derogatory names related to physical hazards. They reflect the lack of understanding of the problem facing the early day miner. Workers were enticed, in some cases, to take a chance against a medical question mark that could not be explained by the doctors of those early days. The optimism of the mining man and the challenge of work led him to believe that the physical results could not apply to himself and only applied to some of his fellow workers. Much of the time, to his dismay, he found that he had lost to the game of chance. As medical knowledge improved and mining management began to understand the effects of conditions in the mines and beneficiation plants, steps were taken to alleviate or eliminate the health hazards that were present, The organizations engaged in mining that did not take an active interest in employee health found themselves to eventually be placed in the position of being forced to take action by Federal and State legislation. We find ourselves in the 1970&apos;s on the threshold of a new era where the general public is concerned vociferously about "their" environment and the industry feels the governmental controls more strongly than ever before. It can be said that in the past 100 years we have advanced from the "Widow Makers" of the 1870&apos;s to the "Retirement Makers" of today. The difficulties of the early days in underground mining were of times compounded in the beneficiation plants above ground. As late as the 1950&apos;s some crushing and milling installations in the United States were operating under environmental conditions that complied to the then existing legislation but were below the health level sought by conscientious management. The Mission Concentrator Crushing Plant was designed in 1959 and placed in operation in July, 1961. In the past ten years the crushing plant has been continuously complimented by technical people, government inspectors and casual

Jan 1, 1971

By Jodi Banta

In an effort to reverse the trend of declining enrollments to mining engineering programs that began in 2015, the University of Arizona has implemented a number of interventions over the past five years, including ramping up its pre-college mining education and outreach, and undertaking several enrollment research projects. This article is the second of two installments to discuss the results of our latest study. The first part can be found in the September 2025 issue of Mining Engineering magazine. To better understand mining’s competitive position, the School of Mining Engineering and Mineral Resources conducted a comprehensive study to determine: 1. How prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree. 2. Factors affecting students’ choices of degrees and career plans. 3. The roles parents and educators play and how they influence students.

Nov 1, 2025

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968

By F. Ikumapayi

Hydrogen peroxide production was measured during the grinding of a complex sulfide ore, and its oxidizing effect on solid surfaces was investigated using Fourier transform infrared spectroscopy (FTIR) with diffuse reflectance attachment measurement. In turn, an attempt was made to correlate the formation of hydrogen peroxide, surface oxidation and sphalerite flotation. Additionally, in order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the effects of major components of calcium and sulfate species present in recycled process water and the effect of temperature on sphalerite flotation were investigated through bench-scale flotation tests using complex sulfide ores. The significance of process water species in flotation was studied using tap water, process water and simulated water containing calcium and sulfate ions. Formation of hydrogen peroxide was revealed during the grinding of the complex sulfide ore, and its formation was counteracted by diethylenetriamine (DETA). The FTIR spectrum of the pulp solid fraction showed varying degrees of oxidized surface species, which are related to the concentration of H2O2 analyzed in pulp liquid. Bench-scale flotation using two different complex sulfide ores showed that sphalerite recovery is better in process water than in tap water. Flotation results also indicated a varied recovery of sphalerite at different temperatures in either tap water or process water.

By John F. Oyler

The performance of high alumina refractory subjected to high compressive loads and high temperatures is an area in which operating experience is quite limited. This paper documents the results of five months of operation of a combustion chamber lined with 83 pct alumina brick subjected to compressive stresses as high as 45psi and hot face temperatures of about 2750°F. It also describes a method for predicting long term subsidence results based on the limited information available in standard hot load limit tests. Descriptions of the chamber itself and the pilot plant upon which its design was based are included.

Jan 1, 1978

By E. Lee Bray

"Editor’s note: The editors thank those who make this annual issue possible. A special thank you goes out to the Industrial Minerals Annual Review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech Geo, is the industrial minerals annual review editor. Edgar Blanco, member SME, of Freeport- McMoRan, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• NickTushar Gupta and Sallie Gaillard, of the USGS, members SME, agricultural materials.• Abhishek Choudhuryand Xihui Yin, members SME, of Montana Tech and Kemira, repectively, ceramic and refractory materials.• Bobbi Strange and Riddhika Jain, members SME, of Outotec, Martin Marietta and Outotec, respectively, chemical raw materials.• Snehamoy Chatterjee, Alyssa Kendir and Alind Chandra, members SME, of BMT, Universityof Kentucky and Michigan Tech, respectively,construction aggregates.• Subham Verma, Gauran Soni and Freddy Sime, members SME, fillers and pigments.• Kaiwu Huang, Thomas Hilderbrand and Ricardo Santander members SME, of Virginia Tech, Thiele Kaolin and Carbo Ceramics, respectively, sorbents, filters and process aids.• Rhaghay Dubey and William Rapier, members SME, of Outotec and a consultant, respectively, specialty minerals.On behalf of ME readers, the editors thankTwo U.S. alumina refineries produced an estimated 1.5 Mt (1.65 million st) of alumina from imported bauxite in the United States in 2018. The 500-kt/a (550,000-stpy) refinery in Burnside, LA, owned by Almatis Inc. produced specialty alumina used in the abrasives, ceramics, chemical and refractory industries. The 1.2-Mt/a (1.32 million-stpy) refinery in Gramercy, LA, owned by Noranda Alumina LLC produced alumina mostly for use in aluminum smelters but also produced specialty alumina. An upgrade project at the Gramercy refinery to convert 200 kt/a (220,000 stpy) of capacity to produce more profitable specialty alumina was completed in the first half of 2018, and another project to increase capacity was started but a completion schedule was not available. The amount of new capacity was not disclosed, but it would be used to produce nonmetallurgical grade alumina. The 2.3-Mt/a (2.5 million-stpy) refinery in Point Comfort, TX, which was temporarily shut down in March 2016, remained closed throughout the year."

Jul 1, 2019

By Andrew Allan

[The Thompson Creek Coal and Coke Corporation, a. mall company engaged in producing coal in the Rocky Mountains of Colorado, is currently engaged in a struggle of destiny to increase their production from inclined seam operation to compete with highly mechanized horizontal bed mines. This paper introduces some of the problems encountered it pitch seam mining as they apply to the convention, room and pillar system employed at the present time. Further described is the test work now being conducted to overcome these obstacles with an. attendant increase in productivity. Included in this test work is a mining machine designed especially for pitching seams, an automated longwall, and hydraulic mining of the latter compared with those of conventional work presently employed.]

Jan 1, 1965

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come, but they are just around the corner. This paper presents a vision of this up-coming revolution in our industry. This vision is comprehensive. It includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For our industry to realize maximum benefits from the information age, we must have a vision of the future that is shared by technologists, machinery producers, and miners.

Jan 1, 1994

By Virgil A. Bilyeu

The Pan American Mine, in southeastern Nevada, is about 26 miles west southwest of Pioche, Nevada, and about 266 miles southwest of Salt Lake City, Utah. The mine is located in the Comet Mining District, and since the ore occurrence is generally the same in the Comet and well known adjacent Pioche Mining Districts, the history of the two shall be considered the same. The Pioche District began about 1869 with the production of high grade gold and silver from fissure veins in the Cambrian Prospect Mountain quartzite. Peak production was reached in 1872 and then declined with sporadic production until 1924, when Combined Metals Reduction Co. shipped its first, complex sulphide ores mined from the CM bed at Pioche. Extensive ore bodies in this CM bed attracted interest in the same bed in the Comet District. Small pockets of high grade silver-lead were mined from fissures cutting the CM and other limestone beds above. Exploration in the CM beds at this time proved a large area of mineralization too low grade to be considered ore.

Jan 1, 1967

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022