Search Documents

By S. Panigrahi

The SO2-ammoniacal ammonium sulfate leach liquor generated by leaching of manganese nodules, after removal of minor quantities of iron and manganese, contained copper, nickel, cobalt, zinc and (NH4)2SO4. After extraction of copper from the leach liquor with LIX 84I, stripping of ammonia from the Cu-barren raffinate was carried out followed by precipitation of metal ions from the ammonia-stripped solution as sulfides. Leaching of the sulfide precipitate was carried out with H2SO4 to obtain a leach liquor containing 0.58 kg/m3 Cu, 2.67 kg/m3 Zn, 2.00 kg/m3 Co, 24.68 kg/m3 Ni and 10.0 kg/m3 (NH4)2SO4. After extraction of copper and zinc from the sulfate leach liquor with LIX 84I and D2EHPA, respectively, the solution was left with Co and Ni. Extraction of cobalt from the Cu- and Zn-free solution was carried out with 0.1 M PC88A and stripping of the cobalt-loaded organic was carried out with the cobalt-spent electrolyte (pH 1.4). Extraction of nickel from the cobalt-free solution was carried out with 90% neutral 1M NaPC88A followed by stripping of the nickel-loaded organic with 120 kg/m3 H2SO4 solution. Extraction of metal ions increased with increasing equilibrium pH and extractant concentration. The maximum separation factors, with respect to the pH and extractant concentration variation studies, were 3796.7 and 15350.0, respectively. The extracted species for the metal ions were CoA2?3HA and NiA2?5HA.

Jan 1, 2009

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By I. Yildirim

Free energy of interaction between particles in water can be calculated if one knows the values of appropriate interfacial tensions, which in turn can be determined from the surface free energies of the particles involved. The latter can be determined using the Van Oss-Chaudhury-Good (OCG) equation. This method requires the measurement of contact angles of well-defined liquids on the surfaces of the particles of interest. In the present work, the contact angles were determined using heat of wetting, capillary rise, and thin-layer wicking methods. The results are compared, and the utility of the surface free energy data obtained from the contact angles are discussed.

Jan 1, 2002

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By M. Bunch

"THE SUPER CYCLE IS GONE The utopia of the rising sales volume, for mining companies from 2002-2011, was entirely due to rising production volume and prices. The Australian mining sector experienced an 18 percent annual growth rate in revenues, and 11 percent growth in prices. (1) However, EBIT remained flat during the same time period. In addition, Australian mines saw a 7 percent annual decline in both labor and capital productivity. (2) Mines in the U.S. and Canada produced similar results, whereas the world-wide mining industry has seen a productivity drop of 40% since 2001. (3) The decade “Bull Run” of rising prices was trashed by companies that chased low-quality assets while increasing debt on their balance sheet. It seemed everyone believed the “super cycle” would last forever, while completely ignoring the history of cycle downturns. Worldwide mining operations are as much as 28 percent less productive today than a decade ago, according to new McKinsey research. The results from McKinsey’s new MineLens Productivity Index (MPI), which adjusts for declining ore grades and mine cost inflation, show that the pronounced decline in productivity is evident across different commodities and is seen in most mining players and geographies. (4) McKinsey sees three important areas of focus to address the root causes of productivity decline. 1) Embed effective management operating systems at mines 2) Prioritized operational excellence and capabilities development 3) Focus on innovation Reality has now settled back in and companies are struggling to make ends meet. The basic management staple of controlling costs and improving the production/productivity that was lost in the excitement is now back in play. Traditional cost-cutting approaches, such as across-the-board spending cuts, layoffs, and hiring freezes are only short-term initiatives and will not permanently improve a company’s cost structure or improve long- term competitiveness. This can only be accomplished by engaging front-line employees and empowering them to make necessary improvements in their daily work. It is time for leaders to lead and develop cultures of continuous improvement within their organizations in order to sustain their mining project to the end of mine life. Successful operating managers require two different skill sets of Leadership and Management; knowing how to lead people in their organization and how to manage the work they do."

Jan 1, 2016

By Eric M. Hill, Daniel E. Walsh, Hsing K. Lin, John T. Hollow

The Fort Knox Mine is located in Alaska’s interior where the average ambient air temperatures range from -24°C in January to 16°C in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Plant slurry temperature cycles seasonally and allows for a unique opportunity to measure the impact temperature has on gold leach kinetics, carbon adsorption efficiency and cyanide destruction reactions. Mathematical models have been developed to accurately predict actual mill performance. This paper describes the development of the models and presents data that allow for a better understanding of the impact of circuit operating temperature on process efficiencies.

Jan 1, 2005

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

Gary R. Steele is vice president, corporate marketing with Energy Fuels Resources. As such, he knows the global uranium market. The following are some of his thoughts on uranium?s place in the global energy picture. ME: What are Energy Fuels Resources? thoughts on the global nuclear power industry? Steele: The global nuclear power industry is a major contributor to the electrical needs of the world. Though generation by nuclear reactors has primarily attracted attention through the reactor accidents at Three Mile Island and Chernobyl, nuclear power continues to quietly and safely provide power to a growing and power-hungry world population. As of March 2008, 30 countries were operating 439 nuclear power reactors. Nuclear power plants provided about 15 percent of the world?s electricity production in 2007. France leads the world in nuclear utilization, with 77 percent of its power coming from nuclear plants. And Lithuania, Slovakia and Belgium each derive more than 50 percent of their power needs from nuclear plants. For much of the developed world, nuclear generation has already been contributing significantly to the supply of electricity. Additionally, 34 new nuclear plants are under construction in 14 countries. Leading the rush to build new nuclear generating plants are China, Russia and India. Each of these countries is building six new nuclear power plants. These 18 plants, totaling almost 12,000 MW of generation capacity, will require about 7.25 kt (16 million lbs) of U3O8 for their initial fuel load and will consume about 2.45 kt/a (5.4 million lbs/year) for the rest of their operating lives. The rest of the world, outside of the United States, has used nuclear power as a viable and economic generation alternative since the commercialization of utility nuclear reactors. And current activity supports the strong future of the nuclear alternative internationally.

Jan 1, 2008

By C. A. Young, J. D. Miller

Thermodynamic data has been obtained for oleate chemisorption at fluorite (CaF2) and calcite (CaCO3) surfaces using adsorption isotherms determined previously at room and elevated temperatures by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS). Linear regression analysis was used to statistically derive free energy data as a function of temperature assuming oleate chemisorption followed Langmuir-type adsorption. Enthalpy and entropy changes were subsequently ascertained from the Clausius-Clapeyron equation and fundamental thermodynamic relationships. Essentially, no difference in the free energy of chemisorption at the two mineral surfaces was found; however, the differences in enthalpy and entropy values were significant. By comparison, the results showed that oleate chemisorption at fluorite surfaces was more extensive and more entropically driven due to more water being displaced. Results correlate well with values determined in the literature for other mineral collector systems. These findings help explain the greater hydrophobic character of fluorite than calcite in both the absence and presence of oleate.

Jan 1, 2002

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By Edward H. Jr. Boyle, Paul R. Thomas

Introduction It is estimated that nearly 40% of all the gold ever mined in free world countries has been produced by South African operations. There is concern that this immense productive capacity will soon decline. Such a decline could reduce world gold supply and lessen the ability of market economy countries (MEC) to exert the major influence upon the world gold market. This paper addresses three general issues concerning South African gold production: • How much gold remains to be recovered from the demonstrated resources of the 44 evaluated South African mines; • How long can production at current levels continue; and • What will be its cost. Table 1 provides production data on the world's 10 largest producers for the years 1971, 1981, and 1983. As shown, South African gold production declined significantly from 1971 through 1981. As of 1981, annual South African gold production had dropped by more than 311 t (10 million oz) in 10 years. Despite this, its mines still produced 656 t (21 million oz) that year, about half the world total. From 1981 through 1983, this trend was reversed. Annual South African gold production increased by more than 21.8 t (700,000 oz). The trend reversal was also evident in the US, Canada, and Australia. This illustrates the general, inverse relationship between gold price and gold production. In South Africa especially, as gold prices increased substantially during the 1970s, the average grade of ore mined (pay limit) was lowered as new, lower grade areas and materials were exploited. Gold production declined in volume. But gold revenues increased, and the lives of the operations were extended. The 1981-83 period was one of declining (US dollar-based, average annual) gold prices that resulted in increasing South African production as average ore grades were raised. South Africa currently accounts for 50% of world production (Fig. 1). Figure 2 illustrates South Africa's contribution to total MEC production in 1971 and 1983. Although South Africa's relative share of production has declined, it still represents the single most important source of new gold supply. In 1983, it supplied more than 65% of total MEC production. South Africa currently produces more than twice as much gold as the Soviet Union (ranked second in world production), and 11 times more gold than the US (ranked fourth in world production). Barring major discoveries, South African gold production is expected to peak in 1987 and begin to decline again throughout the 1990s. The rate of decline is ex-

Jan 11, 1984

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By S. Grogan

Next year marks the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). As the U.S. coal industry scrambles to cope with serious economic difficulties, it is appropriate to examine some other difficulties that have their origin in certain provisions of that ten year old law, and that bear directly on the economic viability of surface coal mining in the west. This paper focuses briefly on three technical issues in the reclamation of surface coal mines in arid regions, and suggests that innovation can resolve these issues. The coal industry operates within a narrow legal context, defined in 1977. In enacting SMCRA, Congress listed among the purposes of the Act ?... to...strike a balance between protection of the environment, agricultural productivity and the Nation's need for coal as an essential source of energy." I maintain that such a balance has never been struck, particularly with regard to the reclamation of mines in the west. One reason is that when SMCRA was enacted its supporters were aware of uncertainties about the potential for successful reclamation of western surface mines. Over the intervening years, as a recent Congressional study report (OTA, 1986) points out, "...the risks these uncertainties may pose to the long term success of western reclamation have been reduced significantly." Unfortunately, SMCRA's enforcement agency, the Office of Surface Mining (OSM) has not yet recognized this fact, and the western coal industry is paying the price.

Jan 1, 1986

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By W. D. Monaghan

Flame cutting and welding is one of the major causes of fires and explosions in underground U.S. coal mines. On May 20, 2006, a flame cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On January 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame cutting and welding operation at the Loveridge Mine caused a fire that resulted in sealing of the mine for an extended period. Finally, on March 19, 1992, an explosion at the Blacksville No. 1 Mine that was caused by welding resulted in four fatalities. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame cutting and welding operations to determine the root causes of these types of fires and explosions. The methodology included interviewing mining personnel who perform flame cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations, and MSHA reports of investigations and accidents statistics were analyzed. The results were used to identify and compare differences between flame cutting and welding practices and techniques in small and large mines, Eastern and Western mines, low seam and high seam mines, room and pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices and interventions were developed to reduce the number of fires and explosions caused by flame cutting and welding. This paper provides a summary of this work. Disclaimer: The finding and conclusion in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupation Safety and Health.

Jan 1, 2009

By Thomas C. Shapiro

This is the second in a series of articles on microcomputers and applications in the minerals industry. The first article (ME, Feb., page 129) discussed microcomputer terms and concepts. This article will discuss software for geology and mining. The third article will cover plant, administrative, and geotechnical software applications. Introduction Geology and exploration are areas where computers have a natural fit. Large volumes of data need to be tabulated, evaluated, and made into maps and reports that allow geologists and management to make a decision on a project or mine. Until recently, the programs that performed these tasks were cumbersome and not user friendly by any stretch of the imagination. Learning time to become an expert in these programs typically would be six months or more. The computers needed to run these programs are expensive mainframes. Several years ago, the use of minicomputers became popular because of their lower cost. Programs were adapted to fit these smaller machines and became friendlier. With the advent of micros, many programs. were rewritten and used the screen capability more effectively, thus providing a real advance in user interface. Programs and Price The definition of micro, mini, and mainframe is becoming blurred. For the purposes of this article, micro refers to either an eight- or 16-bit computer, costing less than $10,000 and, more typically, under $5,000. Mini refers to a 16- or 32-bit computer that typically costs more than $25,000. Mainframe refers to a 32-bit or larger computer that costs more than $250,000. There is a large gray area between micros and minis, and minis and mainframes. Technology and prices are changing so fast that the traditional definitions have become almost meaningless and price has become a better guide. With the arrival of the minicomputer, costs for hardware began to fall, but the programs have tended to remain unfriendly. In some cases, the minicomputer acted as a front end to the mainframe. Cost of both the programs and minicomputers could easily run a minimum of $70,000. A total cost of $200,000 would not have been out of line. The average geologist and company would have a great deal of difficulty justifying such a purchase. The advent of the microcomputer has changed all that. For $3,500 to $5,000, one can buy a 16-bit micro and a printer. Plotters with six pens are available for $2,000 that will produce a 280- x 430-mm (11- x17-in.) map. For several hundred dollars, software is available to act as a word processor, an economic spread sheet, or to perform ground water calculations. In fact, some programs are available for free. Some of these programs are relatively easy to learn. In addition, programs are being developed daily that are easy to use. More importantly, large programs that once ran only on mainframes are being converted

Jan 3, 1984

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009