Search Documents

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By J. Um, B. Morin, P. H. S. W. Kulatilake

Development of a three-dimensional mine visualization model for a section of the mine is addressed first. Discontinuity orientation and location information was taken from this visualization model for use in slope stability analyses. Estimated shear strength properties of discontinuities and mechanical properties of intact rock from the rock mass samples obtained from the mine are discussed next. The paper is then focused on the calculated maximum safe slope angles based on the performed kinematic and block theory analyses using the mapped discontinuities at the mine. Finally, the effects of water that exist in the rock mass, tension cracks, slope face inclination, overall wedge height and double benching on factor of safety of wedge stability are illustrated through limit equilibrium slope stability analyses.

Jan 1, 2002

By M. Fustic, A. H. Paul

The geology of the Muskeg River Oil Sands Mine is described to demonstrate how geologic modeling aided in resource evaluation and material characterization during the feasibility and construction stages. Bitumen is hosted in the clastic sediments of the Cretaceous McMurray Formation which is informally divided into members representing the fluvial, estuarine and marine environments of this transgressive sequence. Lithofacies mapping of drill core provides further detail to classify materials as resource type, for extraction suitability and for construction suitability. Geologic interpretation provides tools for the engineers to produce effective mine plans and for the operators to execute them during mine development.

Jan 1, 2002

By Tim O’Neil

“America’s mining industry brings good jobs to communities across America and provides the energy, minerals and equipment that are vital to our economic security and our way of life.” That was the surprise videotaped greeting from President George Bush at the official opening ceremony of MINExpo 2004in the Las Vegas, NV Convention Center. Jack Gerard reinforced the upbeat mood at MIN-Expo. He praised Nevada Gov. Kenny Guinn for his support of the mining industry, the state’s largest manufacturing sector. Gerard is the president and chief executive officer of the National Mining Association, the sponsor of MINExpo 2004.

Jan 1, 2004

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By John E. Newby

The Brightwater Conveyance System consists of four tunnel segments in three tunnel con-tracts, comprising over 21,760 m (71,400 ft) of pressurized face tunneling in complex glacial and non-glacial soft ground conditions with a large proportion 60 m (197 ft) or more below the ground surface with up to 7 bars groundwater head. This resulted in unique technical challenges for establishing geotechnical baseline values. The process used to develop these baseline values and specifications with regard to the level of risk that the owner, King County, was willing to accept is described in this paper.

Jan 1, 2008

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a substantial quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives we have considered original equipment manufacturer (OEM) haul trucks, commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application, and efficiently manage energy consumption.

Jan 1, 2011

By Y. Wang, K. S. E. Forssberg, A. Johansson, X. Lu

This paper presents the desulphurisation of a fine graphite powder below 80 µm by high gradient magnetic separation. The removal of pyrite (FeS2) and pyrrhotite (Fe1-xS) from the fine graphite powder was carried out with a modified version of the Sala dry HGMS with vibration assistance. In addition, a comparative study with dry and wet HGMS systems has also been performed. In order to establish the performance of the desulphurisation, a test series of varying parameters such as magnetic induction, matrix type/configuration and vibration were performed. As an equipment/process for removing sulphurous impurities from the fine graphite powder, the dry HGMS is deemed useful and comparative with the wet HGMS.

Jan 1, 2002

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By J. L. Hoover

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect bit drill wear and use the equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel Software. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

By Daniel Tao, Jike Qiao, Hao Ren, Feifei Ji, Gonglun Chen

The floatation of niobite was studied using a number of collectors at various dosages and solution pH’s. Octyl diphosphonic acid was found to be an effective collector for niobite flotation with good selectivity. A flotation recovery of 91.2% was obtained with 140 mg/l octyl diphosphonic acid at pH’s less than 5.0. Infrared absorption spectroscopy (IAS) and X-ray photoelectron spectroscopy (XPS) were used to characterize the interactions of niobite with octyl diphosphonic acid. Species distribution diagram of octyl diphosphonic acid and niobium species was used to elucidate the flotation behavior of the mineral with octyl diphosphonic acid. A chemical adsorption mechanism of niobite with octyl diphosphonic acid was proposed. Keywords: octyl diphosphonic acid, electrokinetic measurements, niobite flotation, XPS.

Jan 1, 2005

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study has been conducted to control iron in copper electrolyte streams using Eichrom Industries’s new Monophosphonic /sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27 g/L of iron and can be readily regenerated. In addition, the new resin can be easily synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydro-metallurgical streams.

Jan 1, 2000

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

By M. Alley, P. Schroeder, L. Zelazny, S. Nagle

The Old Hickory mineral sands ore body in Virginia (>2000 ha) currently supports a productive rowcrop agriculture. Reclamation experiments were implemented on pilot-scale mining pits from 1995 to 1998. Half of each mining pit was topsoiled (25 cm) while the remaining half was left as either (1) mixed tails/slimes or (2) re-graded subsoil over tails/slimes treated with 112 Mg/ha yardwaste compost. Post-mining productivity was estimated to be reduced by 23%, 3%, 27%, and 20% for each crop (wheat/soybeans/corn/ cotton) in sequence when compared to undisturbed soils. Variability in surface texture and compaction limit restoration of soil productivity.

Jan 1, 2002

By L. R. Moore

Arsenic is among the list of major contaminants in mining aqueous waste streams. Though the elemental form is toxic, the aqueous oxyanions are more so. The most common forms of arsenic released during mining processes are arsenate and arsenite. The common treatment technologies to date can be summed up in these major categories: oxidation, coagulation, absorption, and media filtration. These methods can often involve many expensive processing steps that may also be limited by variables, such as total dissolved solids, other cations and anions, and the oxidation state of the arsenic. An innovative technology, falling in the absorption category, was developed that can successfully reduce such aqueous forms to a level below the EPA recommendations. This new technology offers a unique and viable solution which is transparent to the above mentioned limitations.

Jan 1, 2012