Search Documents

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By C. J. Webb

Column experiments were performed to determine the ability of Madison aquifer material to adsorb arsenic and other constituents in a heavily mined watershed of the Black Hills in western South Dakota. The Madison aquifer is a karstic dolomite and limestone reservoir that is exposed on the flanks of the Black Hills. Streams that cross the Madison in the eastern Black Hills typically lose all their flow to the aquifer at sinkholes. In this work, Madison aquifer material was obtained for loading of six-inch diameter columns, which were backfilled with Madison aquifer water. Stream water then was allowed to displace the aquifer water during column testing in order to simulate mixing of the two waters at sinkholes and to determined adsorption of arsenic and other dissolved constituents. Initial results show that some adsorption of arsenic occurred when compared to more conservative tracers such as nitrate.

Jan 1, 1999

By L. W. Laage

Throughout recorded history, underground fires have plagued mining operations. Compared with other hazardous situations in underground mining, a fire can become a global problem by swiftly spreading deadly carbon monoxide and other products of combustion (POC's) throughout the whole mine, often without warning. Experience has shown that when fires are detected and located in their early stages, they are much easier to control and proper escape routes can be more intelligently selected. Recent advances in sensor and data communication technology have made reliable mine fire .detection system installations possible. Unlike building construction. in a mine, it is impractical to install detectors at every desired location. Abandoned workings and unsafe locations preclude sensor installations from both safety and economic standpoints. The net effect is that some fires are detected and located early while the location of others, even if detected early, remains unknown too long for effective evacuation and fire fighting.

Jan 1, 1989

By Peng Yu-mei, Cao Zhi-yun, Fan Qing-en

In China, an enormous amount of Au-Ag bering calcines, residues and tailings are produced each year from various sources in mining, metallurgical and chemical industries. For a long time, these materials have been either stored up in dumps or disposed of into rivers, resulting in not only waste of resources but also severe environmental pollution. It is therefore of great significance, both from economical and public welfare points of view, to recover efficiently and make full use of the metallic values from these miscellaneous materials. In this paper the physical and chemical properties of these Au-Ag bearing calcines, leached residues and tailings are described and the current status of their utilization are briefly outlined, followed by a more detailed description of some innovative processes now in practice. Lastly, the potential prospects of gold and silver recovery from these materials in China, particularly in the Hunan province, are envisaged.

Jan 1, 1998

By David J. Collins

The emergence of activated charcoal adsorption as the most popular recovery method for precious metals, has led to numerous innovations aimed at increasing the efficiency of the process. This article describes a change in traditional charcoal transfer methods which will aid in reducing charcoal attrition losses. Studies have shown that significant charcoal attrition takes place during transfer, be it when using airlifts or centrifugal pumps. Tests conducted at Pinson Mines indicated a 4 to 8% loss to the minus 20 mesh fraction of charcoal after three (3) hours of pumping charcoal. Tests conducted while the author was at Jerritt Canyon indicated that charcoal transfer was a major contributor to charcoal losses; a decrease in the amount of coarse charcoal (plus 12 mesh) and an increase in the amount of finer charcoal (minus 16 plus 20 mesh) was noted as charcoal was moved to the head of the adsorption circuit.

Jan 1, 1998

By Pat Gochnour, Jim V. Rouse

Advances in the design and construction of heap­leach pads and process plants have greatly reduced. the potential for accidental releases of process olut1on. While workers in the field, and regulatory agencies such as the EPA have long recognized that the potential effects of any spills would be short term in nature due to cyanide attenuation and degradation (Engineering-Science, September, 1986, Pyrih, 1990, Rouse and Pyrih, 198, Rouse and Pyrih, 1991 ), unfortunately the general pubhc has held a perception that such a spill would be an environmental catastrophe. Few factual data on actual accidental releases have been available to dispel such a concept. Such data now exist and shoul? be disseminated to show that prompt response, using a combination of chemical oxidation, natural attenuation, and enhanced biodegradation of cyanide, can limit the effects of such rare releases, in both time and space.

Jan 1, 1992

By Deepak Malhotra, Sean Armstrong, Linda Baltich

The economic profitability of any mineral company is dependent upon maximizing mineral recoveries while minimizing costs. The effectiveness of any strategy to meet this objective is dependent upon firstly obtaining quantitative information concerning the steady-state metallurgical balance of the plant, and secondly, how efficiently this information is used to improve/optimize plant performance. This two-step approach can be designated as a "plant audit." Plant audits on a routine basis can be very expensive and time-consuming. Most plants have reduced staffs to cut costs. The remaining staff has to spend time to solve production/operation problems, thereby leaving limited resources (i.e., people, time, and money), for plant auditing. This paper briefly reviews plant auditing categories, and a systematic approach to auditing which has been successfully used at several operations. An example illustrating the use of this approach in gold operations is discussed in this paper.

Jan 1, 1992

By James Y. Oldshue, Paul M. Kubera

Most coillillercial processing applications employing mixers in various types of slurry systems are continuous flow. These applications may also be multiple stage, with the stage number varying anywhere from two or three to ten or more. Two questions that usually come up at the beginning of any proposed pilot plant study are (1) can the pilot plant unit be operated batch-wise, and the results extrapolated both on the basis of scale and fluid motion to the full-scale tank which will be continuous-flow (and probably multi-stage), or (2) does the pilot plant need to be operated in a continuous-flow fashion, and if so, does the exact number of tanks/stages that are proposed for the plant need to be used in the pilot plant? We will consider these possibilities in sequence and present the principles involved in running some of the various pilot-plant arrangements.

Jan 1, 1992

By Matthew J. Hrebar

A comparison of hydraulic shovels (HS) versus front-end loaders (FEL) is commonly made when an excavator with some degree of mobility and medium reach is required. These applications are often found in hard rock open pit and surface coal mining applications, among others. The purpose of this paper is to present a comparative economic study of the two excavators. Production data was collected from both HS and FEL manufacturers as well as operating mines. Availability, operating costs, and estimated operating life were gathered from operating mines, while capital costs were obtained from manufacturers. The data was limited to studies and operations which included both types of mid-size excavators. The economic study is followed by a discussion of other factors considered by mine operators in excavator selection. The study was originally made for a presentation at the 23rd Intermountain Minerals Conference at Vail, CO.

Jan 1, 1992

By Eugene R. Palowitch

From the late 1880s to the present, the Appalachian region continues to be a dominant supplier of premium-quality coals. The region contains an estimated 93.4 Gt (102.7 billion st) of demonstrated reserves in Alabama, eastern Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Virginia and West Virginia. Therefore, Appalachia will remain a source of quality coals for the metallurgical, export and utility markets. Figure 1 shows the annual production of coal in Appalachia and nationally from 1970 through 1993 (Energy Information Administration, 1994). During that 23-year period, annual domestic coal production almost doubled. Coal production from Appalachia increased at an average annual rate of only 0.7%. Coal production remained essentially constant at about 409 Mt/a (450 million stpy). Thus, Appalachia's market share decreased from 69.8% in 1970 to 47.2% in 1993 - a drop of almost one-third (Energy Information Administration, 1994).

Jan 1, 1995

By A. N. Papadopoulos

The life cycle assessment and the performance of pine fence posts treated with water borne preservatives and oils after 18 years exposure in ground contact were examined in this study. Vacuum CCB treated fence posts were subsequently treated at their lowest part (ground contact) with creosote using the open hot and cold tank process and exposed under warm dry temperate climatic conditions in Greece. After 18 years exposure, samples were taken from the above ground contact, top, middle and ground contact and tested for toughness using a Denison single blow impact bending test machine. There was no significant reduction of toughness in any of these zones. Chemical analysis of the residual CCB of unexposed and exposed samples by ICP showed that copper and chromium losses were insignificant while boron losses were significant (more than 50% of the initial content). This was attributed to an effect of creosote treatment.

Jan 1, 2008

By J. Loredo

Asturias, in Northwestern Spain, has an extensive mining history. As a result of these historical mine activities where operations have been usually developed with little control on effluents or emissions (environmental regulation of mining activity has only been introduced recently), pollution has been severe in some areas, specially in Hg abandoned mine sites, which constitute one of the major environmental problems related to mining. In many of these sites, materials stocked in spoil heaps can be considered as hazardous wastes because of their chemistry, content on ecotoxic elements and potentiality to spread these to the environment. In the humid climatological conditions of the region, water and wind eroded spoils are dispersed through the environment by different pathways and occasionally surrounding soils and waters are intensively affected by pollution. According to the environmental risks that these unreclaimed mine sites suppose for human beings and ecosystems, remedial options must be considered.

Jan 1, 2003

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By G. Capello

Carboniferous mining basins are today a non-negligible source of energy. So important in fact that returns now justify high investments and costs even for those deposits that were un-economical in the past. Nowadays, if properly explored and exploited, basins previously considered non-minable due to complex structural and stratigraphical situations may be economically interesting. It is while studying a faulted basin with such features that the Authors developed the described computer-aided methodology capable of constructing a model of the physical structure of coal deposits on the basis of stratigraphical data from drillings. The aim of the procedure is to define coal reserves, the exploitation of a deposit being conditioned by the possibility of identifying zones that are technically minable. This objective is pursued by making as detailed a reconstruction as possible of the geometrical, stratigraphical and tectonic features of the coal-bearing seams of a deposit.

Jan 1, 1982

By Otis M. Clarke

The 34th Forum on the Geology of Industrial Minerals gave members a chance to see the geology of various stone and ore deposits displayed graphically in quarry walls and also provided an opportunity to hear and see first-rate papers and posters on the geology of industrial minerals. Also, some field trips passed through areas of spectacular scenery. As a bonus, participants saw scenic mines, some of which are "pretty as a picture." Watercolor paintings prove it. At the Oklahoma Forum, the writer displayed a number of paintings of mines and other landscapes seen during previous Forum trips. These paintings and this brief article are part of a crusade to prove that some mines and geologic vistas are scenic wonders and belong in our visual heritage. It is a plea to save some of our best geologic exposures for future geologists, tourists, and artists.

Jan 1, 1999

By B. Das, B. K. Mohapatra, K. S. Narasimhan, S. K. Bhaumik

The iron ore slimes (d80 ~ 50 µm) generated at Noamundi iron ore washing plant (TISCO), assaying 57% Fe, 4% Si02 and 8.3% A1203, have been subjected to hydrocyclone studies. The effects of different design and operating parameters have been studied to get a product suitable for subsequent use in the sinter mix. The studies indicate that it is possible to obtain a product containing 64% Fe, 1.4% Si02 and 3.5% A1203 with a recovery of 49% iron. The process involves classification followed by separation in a hydrocyclone. By this method, the overall yield of iron ore production in the plant is expected to increase by 8%. Microscopic examinations and X-ray diffraction studies were conducted to elucidate the mineralogy and liberation characteristics of Noamundi iron ore slimes. This paper deals with the findings of the investigations.

Jan 1, 1993

By Jack Bradbury

The open stope room and pillar method of mining is used throughout Ozark Lead Company's underground mine located at Sweetwater, Missouri. This method of mining produces an approximate overall ore extraction of 80%. Pillar recovery, on a limited and experimental basis, was started in January of 1979 to determine the maximum size underground opening that could be mined safely. Monitoring the roof and surrounding pillars for potential failure during this pillar recovery process was accomplished by utilizing a simple rod extensometer to measure roof sag. Boreholes 7.5cm in diameter were drilled 3.5m into the roof to spot any separations or cracks that might have propagated between the bedded layers of rock. Underground openings 85m in length by 46m in width have been mined successfully without roof or surrounding pillar failure. Continued measurements to establish long term results will be necessary.

Jan 1, 1981

By V. Saltas

The present work investigates whether dielectric spectroscopy can be used to detect contamination, which may appear in a natural porous material, due to the spreading of pollution. For this purpose, dielectric and conductivity measurements, in the frequency range of 10mHz to 1MHz, were carried out in sandstone samples, partially filled or saturated with solutions of leachates, at different concentrations. The experimental results suggest that although the role of water is dominant to the measured electrical conductivity, variations of two orders of magnitude are observed due to the different concentrations of leachates, in partially filled sandstone samples. Experimental data are well fitted with a Havriliak?Negami dielectric relaxation function, superimposed with a conductivity term. The parameters of the fitting function have been correlated to the concentration of leachate in the sandstone samples and considerable changes have been observed at low leachate?s concentration.

Jan 1, 2005

By D. Marinakis

Gas hydrates (GH) are crystalline compounds consisting of a water molecule lattice, in the cages of which suitably sized molecules, such as methane or other light hydrocarbons, are confined. Although this solid phase looks similar to common ice, it contains substantial amounts of natural gas. The necessary conditions for natural gas hydrate formation exist in some deep-sea marine environments and in permafrost regions. Despite the extensive research, which has been conducted in the fields of exploration and exploitation of natural gas hydrate deposits over the last decades, there is still great uncertainty over the estimated amount of hydrates that these reserves bear. The present work examines some key features of sediments which affect their capacity to host gas hydrates. The hydrate content of a natural hydrate formation is correlated qualitatively with factors such as temperature, effective porosity, mineralogical composition, bio-surfactants, pore pressure and compaction pressure.

Jan 1, 2006

By V. Avdiyskiy

The most pressing topic raised nowadays by the world community faces environment and social consequences of the business intensification process, primarily that of mining and mineral industry, which is through the number of its activities mostly associated with pernicious impacts. World top managers are confronted with the dilemma of reconciling traditional financial framework aiming at successful business development measured by revenues, shareholder value, profit margin and incorporating Sustainable Development (SD) at all levels of decision making process, avoiding depriving future generations of the means to meet their own needs. The rapid consolidation and globalization of the industry stipulates that companies are an integral part of the world economic environment. Therefore a company?s financial performance is under the pressure of operational and environmental performance. Among them special attention is paid to the social and economic background, the relationship with regulatory institutions, and the developments for environmental protection.

Jan 1, 2003