Search Documents

By William R. Nash

Introduction As ore grades decline and deposit depths increase, problems and costs of mining construction increase rapidly. Ground water greatly impacts the cost of mining construction. In developing or exploiting ore bodies or coal mines, stored ground water in waterbearing formations is often encountered. Man-made conduits or shafts are constructed, as are raise bores for ventilation (up to 6-m-diam or 20-ft-diam), or smaller diameter drill holes, used for either power cables or rock dust. In underground construction and mining, it is possible to inherit unmapped and abandoned drill holes either from oil or gas exploration, or from previous geological investigations. There also exists within underground work exposure to faults, fissures, and jointing. A mine development may encounter unknown aquifers or, unluckily, have an ore body that is an aquifer. Water may invade an existing underground structure, due to concrete deterioration or to damage that may occur to an existing shaft or tunnel concrete lining. An underground development may intersect a drill hole that was not properly grouted when abandoned. It subsequently formed a conduit or an active path to conduct water into the mine. Water inflow may range from insignificant to a magnitude sufficient to inundate an area or an entire underground development. Corrosion imposes major costs. In shafts, it can cause accelerated wear and deterioration, and subsequent early replacement of hoisting ropes. It can also cause deterioration, misalignment, and subsequent accelerated wear and replacement of timber and steel guides and buntons. Utility maintenance (power cables, air, water, and ventilation lines) also can become a problem. Corrosion imposes major costs. Skips and skiploaders provide a never-ending series of maintenance headaches when exposed to an ingress of water. Numerous problems are found in declines with invert and rail maintenance and with partitions in over-under coal mine slopes. Ground water interacting with an underground ventilation system can result in: • Increased ventilation resistance due to roof falls and the spalling of ribs caused by ice heaving. • Restriction in shaft or slope cross-sectional area due to ice buildup during winter months. This may be a safety hazard to access as well. • An increase in the moisture content entering the ventilation air that condenses underground and causes electrical and equipment maintenance problems. Underground structures also incur water-caused problems. The concrete lining in shafts, slopes, and tunnels may be subject to: • Active mine waters causing concrete and reinforcing steel to deteriorate - perhaps to the point of collapse. • Load redistribution around a concrete lining, caused by soil dislocation due to water movement. The resulting stress may be in excess of the calculated design loading. Backwall injection with grout of the completed concrete lining may solve these water inflow problems through low-pressure injections of cement and chemicals. This fills voids at the interface of the concrete lining with either the soil or rock excavation. Surface structures may be jeopardized by lowering the ground water table, resulting in surface settlements. Surface settlements can occur in buildings, headframes, hoist foundations, mills, conveyor structures, or in rail haulage. Areas of differential settlement can lead to derailments, improper wear of hoisting ropes on sheaves in headframes, and the misalignment of bearings and brakes. Mud jacking and compaction grouting may remedy these problems. To reduce operating costs, increase efficiency, and increase safety, inflow water to the mine should be minimized. For an operating mine with a water problem, a water inflow survey should be taken. Quantities of water flow should be examined at all accesses (shafts, slopes, bore holes, and raise bores) at the faces, haulages (rails or conveyors), and sump discharge. From this examination and quantity survey before and after heavy rainfalls, valuable data for elim-

Jan 3, 1984

By Alfred Weiss, Andrew E. Nevin, Thomas J. Neil, O&apos

As Edward E. Runyan, 1983 AIME President, in an interview excerpt in ME, June, p. 607, stated, "...the AIME Transition Committee has recom¬mended to the AIME Board that each Constituent Society be allowed the option of separate incorporation, whereby each could become its own separate legal entity." Background The American Institute of Mining Engineers (AIME) was formed in 1871 by 22 engineers in Wilkes-Barre, PA. Although originally a mining organization, it became a home for metallurgists, iron and steel industry people, and for the individuals in the expanding petroleum engineering profession. There are now four Constituent Societies: Society of Mining Engineers, located in Littleton, CO, 29,000 members; Society of Petroleum Engineers, located in Dallas, TX, 47,500 members; The Metallurgical Society, located in Warrendale, PA, 10,000 members; and Iron and Steel Society, located in Warrendale, PA, 6,500 members. Each of the four groups has grown and continues to serve the specific and/or diverse needs of its membership. As the needs and requirements of their industries and professions change, each of the Societies has perceived and initiated programs that serve their constituency rather than AIME as a whole. Therefore, each Society has recognized an increasing need for autonomy to better augment their own programs. An AIME Ad Hoc Transition Committee, with Robert Merrill, AIME Past President, as chairman, made a number of recommendations pertaining to AIME operations that were approved in October 1982 by the AIME Board of Directors. One of the recommendations was to endorse separate incorporation of the Constituent Societies on an individual-society-option basis. The AIME Board commissioned a task force of Constituent Society representatives to develop specific revisions to the AIME Certificate of Incorporation and the AIME Constitution and Bylaws. This was done to allow separate incorporation and to reflect the decentralized structure of the Institute. The SME-AIME Board of Directors subsequently approved the recommendation of SME Working Party #69 that SME pursue separate incorporation. Meanwhile, Working Party #69 continues to work with the other Constituent Societies and with the AIME Task Force on Reorganization to determine the form and substance of the separate incorporation. Why Incorporate? George Webster in The Law of Associations quoted Chief Justice Marshall's (1819) definition of corporation as: "A corporation is an artificial being, invisible, intangible, and existing only in contemplation of law. Being the mere creature of law, it possesses only those properties which the charter of its creation confers upon it, either expressly or as incidental to its very existence. These are such as are supposed best calculated to effect the object for which it was created." SME-AIME attorneys, Davis, Graham & Stubbs, have pointed out that the status of an organization operating as an unincorporated association is always unclear. At present, SME-AIME administers assets of almost $3.5 million (mainly property and inventory) but technical ownership and ability to enter into contractual relationships resides with AIME. However, the operation appears to outsiders (particularly those with whom SME-AIME does business) to be an independent operation which would be expected to be a legal entity in its own right. Advantages of Incorporation Liability. Because of legal ownership by AIME of all assets of the Constituent Societies, those assets are subject to the claims of any of the creditors of AIME or any of its constituent parts (i.e., the other societies). Liabilities can be those usually encountered in business but also encompass special risks, which could develop if there were a careless and erroneous publication of material that might be used in practice or if standards are improperly established. The recent US Supreme Court decision in American Society of Mechanical Engineers, Inc.,

Jan 10, 1983

Throughout the 1970s, the US Bureau of Mines rode an ebb tide in Washington political circles. In rapid fire succession, the agency lost its mine health and safety enforcement responsibility (1973), a large portion of its energy research responsibility (1975), and then its fuel statistics functions plus a sizable portion of its coal R&D (1977). By 1978, johnny-come-latelies in the Energy, Labor, and Interior Departments had siphoned away from the Bureau some $125 million in program responsibilities as well as 900 of its employees. The bruising decade came to a close with a Department of Natural Resources proposal that, in its original form, would have scattered the Bureau's responsibilities to the winds. "There is no doubt in my wind," said Lindsay Norman, acting director of the Bureau of Mines (see box), "that were the Bureau to continue down the path it was on, the next step was closing the doors and going out of business." The doors are still open, but erosion of responsibilities had a devastating effect on the resources available to fulfill the Bureau's mission. Devastating, too, in terms of internal morale, considering the Bureau had six directors in a 10-year span. "When the troops are in the trenches and are being shot at," Norman said, "they need a leader-hopefully, a permanent one- that can get them advancing. This is something the Bureau did not consistently have in the 1970s." In September 1978, Roger Markle climbed aboard as director of the Bureau to rejuvenate the 70-year-old agency. He resigned only six months later* but the program Markle set in motion is being carried through by Lindsay Norman. Since Norman's appointment as acting director, he has spent considerable time on the road explaining his agency's redefined goals. At one such stop in Duluth, Norman and his two deputy directors, Charles Kenahan and Mike Kaas, answered the following questions. Lindsay, you were the principal architect in the Bureau's 1979 reorganization. How about a glimpse of what that entailed? Toward the end of the 1970s, after almost a decade of steady dismemberment, we reached what we felt was a critical point in the Bureau's history-we had the choice of redefining and strengthening our organization to meet the mineral challenges ahead, or continuing down the path toward the agency's eventual demise. We felt the Bureau's mission too important to abandon, so in 1978 with Roger Markle as director we initiated a six-month, no-holds-barred intro spection of just what the Bureau should be doing, why, and toward what ultimate national needs. And what did this self-reflection reveal? That there is, indeed, a unique federal role for the Bureau of Mines-that of a lead agency for influencing mineral decisions and pioneering tomorrow's technologic advances. Don't confuse us with policymakers, we're not. But we are policy analysts; we're scientists, engineers, and mineral professionals who can offer a sorely needed source of objective, accurate information to decision makers in both the public and private sectors. I feel there is no better brain trust in government than the Bureau when it comes to mineral expertise-of course, I'm biased. Do I understand you to say the Bureau of Mines is an advocate agency for the minerals industry? We plead no parochial interests, nor ought we, but from our viewpoint a sound minerals industry is extremely important to the broader national goals of security and a healthy economy. US dependence on foreign sources for critical minerals, the increasing noncompetitiveness of some US mineral sectors, and the array of land use issues surrounding mineral-rich lands all have much more serious implications than many otherwise informed people seem to recognize. In your estimation, how vulnerable is the US to foreign mineral suppliers? Let me make a distinction between dependency and vulnerability. The

Jan 4, 1980

By M. C. Fuerstenau, J. J. Fitzgerald

Aluminum silicate hydrosol synthesis and characterization are discussed. Plausible polymeric aluminosilicate species are presented together with their effect on electrokinetics of selected minerals and flotation response of various ores. The addition of aluminosilicate hydrosol to porphyry and oxide copper ores and to a tungsten ore resulted in enhanced flotation recoveries ranging from about 1.5 to 5 percent. A significant portion of the nation's mineral resources are presently lost in the form of particles with very fine grain size. In the case of copper, for example, approximately 225 million tons of ore are concentrated by flotation per year in the United States. Total losses from porphyry ores are generally 15 to 20 percent with half of these losses being finely-divided copper sulfide minerals which do not respond to flotation. The additional 5 to 10 percent loss is the result of copper oxide minerals which are not floated. The losses of copper sulfide minerals are thought to be due in part to the lack of appropriate dispersion of the finely-divided solids less than 20 microns in size. To effect dispersion in flotation systems, sodium silicate is commonly added. Enhanced dispersion effectiveness is achieved when polyvalent metal salts are combined with sodium silicate. Since originally described by Patek (1), numerous workers have explored the utility of metal silicates. Makrousov (2), Belash et al. (3), and Eigeles (1950) (4) showed the applicability of these reagents to calcite/apatite and fluorite/calcite ores. Mercade (5, 6) reported depression of calcite in the presence of 3.33/1 mole ratio Al/Si hydrosols prepared from Type N sodium silicate (Si02/Na20 ratio 3.22/1) and 1% A12(SO4) 3•18H20 solutions. He importantly observed that the colloidal precipitates did not play a significant role in dispersion and depression but that the soluble species were responsible for this action. Patented work by this author described metal silicates used to depress calcite in scheelite flotation using 1% metal salt (FeSO4•7H2O, CoSO4•7H2O, etc.) and 5% Type N sodium silicate solutions to produce hydrosols with Si/Fe or Si/Co ratios of 8.79/1. Aluminum (III) ion systems were less effective as depressants than the iron and cobalt systems. Yang (8, 9) has studied metal silicate sols for use in the flotation of lithium and ultra-fine hematite ores. Using 10/1 Si/Fe mole ratio hydrosols prepared from 2% ferric nitrate, Fe(NO3)3.9H20, and 5% Type N sodium silicate solutions, solutions, he showed that the hydrosols either modify the slime particle surfaces or are adsorbed on the slime particles preventing anionic collector adsorption. In a subsequent patent, Yang also reported the use of these hydrosols as dispersants for beneficiation of lithium ores. Recent studies of aluminum silicate hydrosols in the flotation of chalcocite, chalcopyrite and scheelite have been reported using Si/Al dispersants prepared from 5% Type N sodium silicate and 0.1 M aluminum chloride (A1C13.6H20) solutions. Dispersant properties were shown to be dependent upon the method of synthesis, supernatant pH, and the hydrosol Si/Al mole ratio. Polymeric soluble species in these hydrosolsupernatants have been proposed as the active dispersant species. Aluminosilicate hydrosols are synthesized by the general reaction scheme presented in Figure 1. Commercial sodium silicates are available with ratios of SiO2 to Na20 of 1.60-3.25. The sample which is most frequently employed is Type N whose ratio of Si02/Na20 is 3.22/1.00. Gel filtration chromatography and NMR studies have shown that these sodium silicates contain numerous species of molecular weight from 325-2,000 gm/mole. Monomeric, oligomeric and higher molecular weight linear polymeric arrangements of these structures are found in these solutions.

Jan 1, 1989

By James M. Barker, Richard O. Y. Breese

The recognition of perlite as a distinct volcanic glass, and of the arcuate fractures that often characterize these natural glasses, dates back at least to the late 19th century and perhaps into the 18th century (Howell, 1974). Some authors suggest that recognition of perlite dates considerably further into antiquity, perhaps to the 3rd century BC (Caley and Richards, 1956). Most recent definitions identify perlite by the presence of vit¬reous, pearly luster and by the presence of characteristic concentric or arcuate perlitic fractures. As discussed more fully below, arcuate fractures in perlite need not be megascopic. The textures of perlite which commonly occur in deposits range from dense to highly vesiculated to pumice-like. Thus, the classical definition of perlite is descriptively restrictive compared to the natural range of textures and neglects to address the issues of genetic origin and geologic occurrence. In spite of the petrological usage of the term perlite, the in¬troduction of expanded perlite aggregate into industrial markets caused the term to be applied as well to the lightweight, cellular aggregate that is produced through the rapid thermal expansion of milled perlite ore. Perlite is distinguished petrologically from other natural glasses by a silicic or rhyolitic composition by the presence of 2 to 5 wt% total chemical water held within the glass structure and often by the presence of pearly luster and onionskin-like perlitic fractures. Worldwide, occurrences are associated with Tertiary through early to middle Quaternary volcanics and with the glassy portions of silicic domes and flows, with vitric tephra, with the glassy chill margins of dikes and sills, and with the glassy portions of welded ash flow tuffs. Less commonly, perlite is reported in association with the glassy portions of volcanic plugs and lacco¬liths. The perlite carapaces that partially or fully comprise extru¬sive domes and flows are often thick and areally extensive, and thus provide commercially attractive targets for low cost open pit mining. Perlite tuffs and tephras are also important commercial sources. Mining costs are minimized by open pit quarrying and by either bulldozer ripping or blasting. Crushing and sizing facilities are generally close to the pits. Due to the low weight and large volume of expanded perlite, unexpanded perlite that has been crushed and sized is usually shipped nationwide directly to local markets where it is expanded and processed for distribution to end users. The vast majority of international trade is in unexpanded perlite. In the United States, the evolution of the expanded perlite industry can be traced to the late 1930s and early 1940s when expanded perlite aggregate was introduced into gypsum plaster and concrete markets as a substitute for vermiculite (Schundler, Jr., oral communication, 1991) and was promoted for use in a much broader spectrum of products (Howell, 1974). By the early 1950s, end user markets were well established and small expanders were numerous east of the Mississippi River. Today, mining and expan¬sion is undertaken throughout the world. Worldwide production of perlite is dominated by the former Soviet republics, the United States, and Greece. Total worldwide production of processed perlite during 1990 is estimated at roughly 1 778 000 tons (Davis, 1991). The physical properties of expanded perlite that give this prod¬uct unique commercial value include: low bulk density, chemical inertness, high insulating ability, nonflammability and fire resis¬tance, and its ability to retain water. These and other physical properties give expanded perlite value in such uses as: lightweight acoustical and thermal insulating aggregate; component in plaster, insulating cements and lightweight concrete; loose fill insulation; as aggregate in horticultural applications; and in milled form as filter aid. In the United States and Europe, the largest end use is within building construction products.

Jan 1, 1994

By Brian McInnes, Joseph A. Sopko, Behzad Khorshidi

"The Port Mann Main Water Supply Tunnel involves a 1km long tunnel beneath the Fraser River from Surrey to Coquitlam, BC. At depths of up to 60 m below ground, the earth pressure reached 6 bar. The tunnel is constructed using an EPB TBM and gasketed precast concrete segmental liner. The tunnel and two shafts were constructed in a variety of soil conditions ranging from soft to stiff clays and silts, to compact to very dense sands and gravels. After approximately 800m of mining, a very dense and highly variable soil group consisting of cobbles and boulders halted the TBM. Several options were considered to stabilize the TBM face so an intervention could be conducted. Although de-watering was considered, there was risk of settlement to the Port Mann bridge piers, which was within 500m of the tunnel. Hyperbarics were also considered, however, the cost, schedule and uncertainty of the work that needed to be done, made it a risky option. Ground freezing by Liquid Nitrogen was chosen as the best solution, which would provide a frozen block around the face of the TBM. A temporary platform on the river was designed and constructed to enable drilling and installation of the freezing pipes and temperature monitoring equipment. The operation required close coordination among the tunnelling, marine and freezing sectors. Following the intervention, the TBM successfully broke through the reception shaft, and the remaining project was completed. This paper describes the design, construction and operational approaches used for the freezing and serves as a basis for future projects requiring expedited ground freezing."

Jan 1, 2016

By R. H. Smith

The total energy demand in the United States increased about 4 per cent annually during the 1960's 1 and is expected to increase at the same rate during this decade. Z Fuel oil growth in the 1960's was only Z per cent per year until 1968, but it increased to 8 per cent in 1969 and 11 per cent in 1970. Fuel oil demand is expected to grow at a 6 per cent rate through the 1970's. Part of this rapid increase in demand has been caused by restrictions placed on the sulfur content of fuels. High sulfur coal can no longer be burned in many parts of the country and has been replaced by low sulfur fuel oil. An insufficient supply of natural gas has also contributed to fuel oil demand. Air pollution regulations have not only caused an increase in fuel oil consumption, but they have also caused a reduction of sulfur content in residual fuel oils. Current regulations call for 1 per cent maximum sulfur content fuels over much of the country. Sulfur contents of fuels are limited to 0. 3 per cent in certain areas on the east and west coasts. Sulfur in residual fuel oils from high sulfur imported crude oil is reduced to 1 per cent currently. However, sulfur reduction to 0. 3 per cent is difficult and expensive.4 As a result, refiners may be hard pressed to supply the market for low sulfur fuel oil. The oil shale deposits in Colorado and Wyoming potentially are a huge source of low sulfur fuel oil. It will be shown that the low sulfur content and more importantly the sulfur

Jan 1, 1972

By R. V. Johnson

The review of mineral activities in Minnesota arrived too late to appear in the May issue. Minnesota continued to lead the nation in iron ore production in 1989 with more than 70% of the market. At no time in the past 50 years has Minnesota's iron ore market share fallen below 50%. 1989 production was provided by six iron ore pellet operations and one high-grade iron ore mine. Most American steel companies are represented in these operations through whole or partial ownerships in Minntac (USS), Minorca (Inland), Eveleth Mines (Armco and Rouge), Hibbing Taconite (Bethlehem), and LTV Steel and National Steel Pellet. A seventh iron ore pellet producer started up in 1989 when Cyprus Minerals acquired the assets of bankrupt Reserve Mining Co. This operation, with first production scheduled for 1990, will be the only non-steel company captive operation in Minnesota. Encouraging minerals development In an attempt to stimulate further and additional mineral development in Minnesota, the state's legislature established a Minerals Coordinating Committee (MCC). This committee is comprised of the Department of Natural Resources-Division of Minerals, the Minnesota Geological Survey, the Natural Resources Research Institute, and the Mineral Resources Research Center. The Committee has sponsored and coordinated various projects. Among these MCC-sponsored projects are glacial drift geochemistry with an emphasis on gold and indicator minerals, accelerated geologic mapping, continued aeromagnetic surveying of Minnesota, greenstone geochemistry, structure and stratigraphy of the Duluth complex, and drill core and exploration data acquisition from past exploration programs. Regarding drill core, the Division of Natural Resources completed construction of its third core library building in Hibbing. These data and core are available for public examination.

Jan 1, 1990

By Henry Antwi

The decade of the 1990s promises to be one of increasing internationalization for domestic minerals producers as they scramble to enhance relative positions in highly competitive, international minerals markets. This "international mining rush" is fueled by developing countries seeking international investment capital to explore for, develop and exploit sizable mineral endowments in an attempt to support the increasingly popular, but expensive, wave of democracy and selfdetermination sweeping the world. This "fuel" typically takes the form of revised mining codes and, often, lucrative investment incentives. These incentives include favorable tax rates, royalty provisions, relaxation of import/ export constraints, depreciation schedules, profit repatriation and other variables that can positively impact mineral investment decision making. Concomitantly, in their attempts to address real and perceived short- and long-term woes associated with enhancing competitive positions internationally, many domestic explorers and producers are attracted to the prospect of finding high-grade deposits in relatively virgin areas. Combined with the investment incentives provided by foreign governments, these high-grade deposits promise lucrative potential returns from projects having short payback periods. Classic examples of this mutual desire to intensify international mining efforts by domestic producers are illustrated by activity levels in countries like Chile, Bolivia and Venezuela in Latin America and, more recently, in Eastern Europe and select locations in the former Soviet Union. As US corporations scurry to send fact-finding, technical, evaluation and financial teams to these presently popular locations, one area of the world has received little attention - Subsaharan Africa. Specifically, the country of Ghana (formerly the Gold Coast) deserves more attention than it appears to be receiving from North American mining companies.

Jan 1, 1992

By Lawrence Neal Post

Introduction Synthetic soda ash production began to decline in the late 1930s. This was due to high operating costs and waste disposal problems. Since soda ash was used as a major component in manufacturing glass, an alternate method of producing that chemical was necessary. A process to produce soda ash from trona was developed by FMC Wyoming Corp.'s predecessor, as well as an economical way to obtain trona. Existing trona operations are located about 40 km (25 miles) west of Green River, WY. Five operators presently mine trona in this area. FMC's property has 153 km2 (59 sq miles) leased. Its eight shafts reach 488 m (1600 ft) deep to the uniform trona deposit. The seam ranges in thickness from 2.4 to 3.6 m (8 to 12 ft). History Egyptian tombs, dating from 4000 to 3000 BC, contained mummies preserved by an embalming process using soda ash. For many years, soda ash was produced by burning marine plants, then dissolving the soluble material (sodium carbonate) from the ashes. The name soda ash is derived from this method of production. In 1791, Nicola LeBlanc developed black ash, or salt cake, from salt, sulfuric acid, coal, and limestone. This process remained in use until 1863, when Ernest Solvay developed a method for producing soda ash from salt, coke, and limestone with ammonia as a catalyst. This Solvay process was widely used. And, in the 1930s, there were 17 plants in the US alone. High plant operating costs and waste disposal problems, however, necessitated finding an alternative to the Solvay process.

Jan 10, 1985

By J. Hanna, H. R. Gonzalez

Discussion by N.L. Hargett Dear Dr. Hanna: As discussed in our phone conversation, we are enclosing a suggested revision to the paper, "Application of Bentonitic Clays in Suspension Fertilizer Formulations," published in MINERAL & METALLURGICAL PROCESSING, May 1990. The revision will replace the second paragraph in the article. The reason for the revision is that suspensions have decreased in market share since 1984 and at present comprise an estimated 25% to 30% of fluid mixtures. This represents 6% to 7% of all fluids and only 2% to 3% percent of all fertilizers. Based on national surveys conducted by the Association of American Plant Food Control Officials (AAPFCO), suspensions comprised an estimated 25% of all fluid mixtures in 1974, 33% in 1976, 35% in 1980, 40% in 1984, and 36% in 1988. Revision to "Application of Bentonitic Clays in Suspension Fertilizer Formulations." Suspension fertilizers are an important segment of the fertilizer industry in the United States. Suspensions allow higher concentrations of nutrients (N, P2O5, K2O) than clear liquid solution fertilizers. K20 content of solutions is limited to about 10%, while suspensions can contain more than 30% K2O. Suspensions can tolerate greater variations in temperature than solutions. In suspensions, if crystallization occurs, the crystals can remain suspended in a clay jell instead of settling as they would in solutions. Solubility is not a limiting factor in suspensions, since complete solubility of phosphate is not required. This allows a wider range of phosphate materials to be used. Also, materials commonly used in formulating suspensions are less expensive and more widely available than those for clear liquids (Getsiner et al., 1984).

Jan 1, 1992

By Ora H. Rostad

Veins containing silver and gold values, with some associated values in copper, lead, and zinc, were discovered in 1890 by Will Kirwin in what was later designated the Kirwin mining district situated on the North Fork of the Wood River, about 56 km (35 miles) west of Meeteetse. (See Fig. I.) After considerable prospecting activity, including the driving of several short adits on veins, most of theclaims in the district were consolidated into two ownerships. One was held by the Galena Ridge Mining Co. which was organized on Nov. 18, 1902. The other was held by the Shoshone Mountain Mining Co. which was organized on Mar. 23, 1903. During the period from 1903 to 1907 inclusive, the two companies continued exploration on veins in their respective areas. The major exploration-development activity for the Galena Ridge Mining Co. was the driving of the Galena Ridge crosscut adit for 709 m (2327 ft), to cut veins at depth which had been explored by short adits high on Galena Ridge. Shoshone Mountain Mining Co. concentrated their work on the Bryan and Pickwick veins. Neither of the companies found ore that was rich enough to sustain profitable operations in that remote locality. Most of the major exploration and development activities were stopped in late 1907. A major snowslide in February 1907 killed three people and destroyed several buildings and may have contributed to discouragement in the area. From 1908 to the early 1920s, only minor exploration work was done. Galena Ridge Mining Co. was dissolved Aug. 5, 1922, and Shoshone Mountain Mining Co. was dissolved on Mar. 23, 1923.

Jan 1, 1991

By Fernando H. Muge

The first application of dynamic pro¬gramming to the problem of grade control and scheduling was by Muge et al (1979) and Ribeiro (1982) who applied it to the simple, two-dimensional case of longitudinal open stoping using two sublevels. In this paper the formulation of the problem is extended to cover the general case applied to a cut-and-fill mining method. The criterion for optimization is the total deviation of the average, grades of mining blocks from the overall average panel grade (or the average grade of a set of mining panels or the mine processing working point). This means to schedule the operation by removing a certain number of mining blocks at a time, subject to the geometric (mining) constraints, and such that the total deviation of average block grades from overall average grade is minimum. The method can be applied to complex orebodies with several ore characteristics and the deviation of each one of these characteristics can be further constrained by specifying maximum values. The method can also be generalised in order to take into account any necessary geometric constraints used to define the mining method. In this paper a case study is presented concerning the mine planning of a complex sulphide orebody located in the South of Portugal. As input for the definition of the mining sequence, a geostatistical numerical model of the orebody was built based on a previous ore typology. The short term planning is used to assess specific mining sequences and the production scheduling is performed on the basis of an objective function (e.g. minimization of grade fluctuation).

Jan 1, 1989

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991

By Etienne Simode

When a fire breaks out in a mine access road, the hot smoke, due to heat transfer with the surrounding strata, progressively cools as it moves forward. Depending upon the resulting temperature distribution, the density of the fluid changes. This change will bring about: Firstly, a variation in the resistance of the roads, a static factor which will affect ventilation flow rates; Secondly, the appearance of extensive aerodynamic driving loads in the vertical and angled roads, a dynamic factor which can have an extensive impact on ventilation. Because of the appearance of combustion and distillation products, the vaporization of water, which wets the timbering and strata, and the expansion of gases, fluid rates can at times be increased tenfold in the area of the fire. These disturbances may cause explosions and ventilation inversions, which fill other working areas with smoke toxic to workers, and which can come up upon rescue teams from behind. Due to the progressive heating of the surrounding rocks, which will slow down heat transfer, these dangerous conditions change over time. At the Lorraine Basin Coal Mines, programs have been set up and employed for the computer simulation of these phenomena over time. They serve to anticipate or to understand such phenomena, the input data being the characteristic parameters of the mine ventilation network, the operating curve of the main fans, and measurements or estimates of some temperatures. Two programs, employed together, have been developed for these studies: One program, called RESO, calculates the distribution of flow rates and pressures throughout the entire network; The other, called FEUMIN, determines smoke temperatures over their entire path.

Jan 1, 1980

By Joe Komadina

DOUG HALBE: Our next topic is one that I would think everyone might want to contribute to. I'm sure everyone here has had some experience in this area. If you haven't, I'd suspect you've never really run a mill. This is what we call "Horrible Spill Areas We Had When We Started Up the Plant and How We Fixed Them." Our next speaker has had a really great operating career. He had many years with Newmont in the Carlin area, and now he's executive vice president and chief operating officer of Independence Mining Company: Jim Komadina. I don't have to be nice to the speakers anymore, do I? [laughter] You may wonder why we picked Jim Komadina to give this talk. I was involved many years ago in the start-up of Newmont7s Gold Quarry plant. Jim held quite a responsible position there. I'm not going to say anymore, but I have in the back of my mind this picture of the pump floor and a rowboat and a guy rowing around on the pump floor. [laughter] Jim, was that you? [laughter] JIM KOMADINA: Probably. I wasn't responsible for the design. [laughter] Actually it's amazing. I've seen a lot of these plants and actually had the opportunity to walk around them, so when I say this, "Horrible spills I have seen and done," it's because I've been responsible for more than my fair share of them. But having seen a lot of spills, I will present a little bit of wisdom about how to prevent them.

Jan 1, 1998

By P. Malozemoff

Discussion by P. Malozemoff I have no objection to using mathematics in the value appraisal of properties. The factor that is not emphasized in the paper is that very few important properties have a lifetime that reflects the initial ore reserves of the property divided by the rate of production adopted. In the majority of cases, major properties mine out several times the initial reserves. How much more will be mined out is not known, and only exceptionally gifted geologists can predict that additional reserves will be found. There is the further factor of metals price, which, over the long term, is not predictable. Another factor vitiating making calculations on initially established ore reserves is the speculative nature of exploration success. In my judgment, the life of a property, in addition to an established ore reserve, should include ample time for exploration to find additional reserves. The likelihood of additional reserves is based on the geological promise of the general area where the mine is established. This is especially important because of various risk factors associated with small orebodies, the economic life of which is about five to seven years. In underground mines, it is not economic to develop reserves beyond a certain depth, so the life of initially established reserves must be limited. In these cases, it is especially important to have a good geological understanding of the orebody and its continuity. To accommodate these concepts and present proof of economic soundness for a mining enterprise, a mathematical analysis should yield a life long enough to allow exploration and the development of additional reserves that would ensure a longer mine life and a more profitable result.

Jan 1, 1994

By Pieter Berendsen

Lamproite occurs in two locations in southeastern Kansas that are in close proximity to each other. In both locations, the lamproite is restricted to north- east-elongated, ellipsoidal depressions measuring about 3 mi by 1.5 mi. At the surface and in the shallow subsurface, lamproite occurs as sills that were intruded into Middle and Upper Pennsylvanian rocks consisting of shale, limestone, and minor sandstone. Isotopic age determinations by Zartman and others (1967) indicate that the lamproite was intruded during the Late Cretaceous (88-91 my). Drillholes for hydrocarbon exploration down to a depth of about 1,400 ft (top of the Mississippian) and numerous shallow drillholes (mostly 200-300 ft) by the Kansas Geological Survey in the northern portion of Silver City dome helped to understand the structural complexity and extent of the near-surface sills. Numerous radial faults showing small apparent vertical offsets limit the lateral continuation of individual sills. Concentric faults are believed to mark the edge of the depression. Wagner (1954) mapped the geology of Silver City dome in considerable detail and recognized a northward dipping, 120-ft-thick, lamproite sill exposed at the surface along the northeastern edge of the dome. The upper 40-50 ft of the sill weathers olive-brown and has a soft, clayey consistency in which only the phlogopite mica is recognizable. The weathered material has been mined by Micro-Lite LLC since 1982 from the exposed sill in an open-pit that measures about half a mile extending in an east- west direction. The bulk of the material, about 98%, is used as an additive in mineral supplements for cattle feed.

Jan 1, 1999

By Larry Snyder, Levent Ozdemir, Charles Fishman, Fun-Den Wang

Tunnel Boring Machine Instrumentation A 9.17 m. diameter tunnel boring machine presently in operation in Chicago, Illinois, has been instrumented to continuously monitor and record machine thrust, torque and penetration rate during boring. A micro-processor-based data logger capable of monitoring up to 60 channels of data digitizes and converts into appropriate engineering units the signals from various transducers mounted on the machine. The output from the data logger is sent to a teleprinter, providing a permanent record of measured data. The program control enables the data logger to scan all data channels at desired time intervals. Data obtained to date have been analyzed to determine the interrelationships of the parameters measured. Penetration rate was found to increase linearly with machine thrust with a unit increase in thrust causing more than a unit increase in penetration rate. For low thrust levels corresponding to the initial stages of a boring cycle, the penetration rate was observed to behave erratically until the thrust pressure was sufficiently high for the cutters to establish full contact with the tunnel face. Torque showed a curvilinear increase with machine thrust, reaching the design rating at about 70% of maximum available thrust. No-load torque was approximately 20% of the machine's rated torque capacity. Overall, the trends observed in measured machine parameters correlated closely with those predicted from experimental and theoretical boreability studies. In summary, the instrumentation system has mett two basic goals. First, it provided extensive and accurate boring data and secondly, it has proven that an automatic data acquisition system can be installed on a TBM and can function under adverse environment.

Jan 1, 1979

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991