Search Documents

By C. D. Wittreich

The results of an engineering study of fiber-reinforced cemented tailings are presented. These tests were conducted to evaluate the potential for using fibers to increase the strength of cemented tailings used as backfill for ground support in the undercut -and - fill mining method in a mine subject to high horizontal stresses and rock bursts. Stress-strain measurements indicate that fibers not only increase the peak compressive tensile and flexural strengths of cemented tailings, but limit reductions in residual strength following failure. Results also show the effect of water content, fiber type, fiber density, and curing time on strength.

Jan 1, 1987

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics The analysis suggests grinding depends mainly on the state of aggregation of the ground products inside the mill and pulp fluidity Implications of the observed effects on ultrafine grinding in general are discussed

Jan 1, 1983

By M. M. Ragin, B. J. Scheiner

The US Bureau of Mines (USBM) has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. It was found that at a given polymer concentration, there were an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By W. A. Niepelt, F. A. Locher

Flow in steep cascades may lead to the occurrence of a nearly periodic train of waves known as slug flow. This, in turn, may result in overtopping of the channel walls and problems with energy dissipation in receiving sumps. Experimental data from an operating facility was used to extend clear water technology for predicting the occurrence of slug flow to conditions with slurry flows. A design methodology and a design chart to determine the region of steady flows is presented that will permit the design engineer to avoid slug flow in cascade systems for conveyance of slurries.

Jan 1, 1990

By Y. Luo, S. S. Peng

This paper presents some results obtained from research on long-term subsidence over and near chain pillar systems - the area available to long-term subsidence in longwall operations. Although the long-term subsidence for most longwall operations is insignificant, it does exist in some cases. In the cases that showed significant long-term subsidence, it was found that the development process could be expressed by an exponential decaying function. The stability factor of the chain pillar system and the potential for long-term subsidence are the two most important factors that control the magnitude and development characteristics of the long-term subsidence process.

Jan 1, 2000

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002

By R. W. Smith, S. A. Davis, A. M. Raichur, M. Misra

The flocculation of coal is typically accomplished by the addition of commercially available polymeric flocculants. Recently it was shown that biopolymers derived from microorganisms can also be used. The biopolymers flocculate coal efficiently and make the coal more hydrophobic. This increase in hydrophobicity can be utilized to separate coal flocs and can be used for reducing the moisture content of the flocculated coal. In this regard, flocculation and settling tests using biopolymers and synthetic flocculants were performed on fine coal. The experimental results are discussed and a transport model is presented for the time-dependent settling of fine coal.

Jan 1, 1998

By W. H. McDonald, D. D. Carr

The use of stone in building construction predates written history. From the time that stone was first used, builders have constructed stone buildings predominately from local or regional materials. However, since World War II, the stone business has become increasingly global. For example, French limestone is now sold to builders in the United States, and American granite is shipped to Japan. The internationalization of architectural and construction firms has encouraged this trend. Differences among nations in trade practices, environmental demands and the level of knowledge of dimension-stone characteristics make international trading in stone a risky and potentially disastrous business for unwary participants.

Jan 1, 1997

By D. R. Taylor, R. G. Goss

The use of clay-based granules as carriers for pesticides dates back to the early 1940s. It now represents a business conservatively estimated at between 180 and 270 kt/a (200,000 and 300,000 stpy) in the United States alone. Prices for these materials typically range from $110 to $165/t ($100 to $150/st). Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits, which are reviewed. Topics discussed include drift control (vs. liquid sprays), mobility (in the environment), worker safety and transportation (spill) safety.

Jan 1, 2000

By G. R. Denham

Innovative designs, mining, construction and reclamation practices are used at PT Newmont Nusa Tenggara's Batu Hijau mine on Sumbawa Indonesia to develop a cost-effective, environmentally sound, stockpile and dumping system. The mine production rate is over 200 million tonnes per year (50 million tonnes processed with 150 million tonnes being stockpiled for processing later or placed in waste dumps). Dump development for over 150 million tonnes per year in a mountainous, tropical environment, while meeting environmental and permitting requirements is not an easy task. The effective implementation requires innovative techniques and practices from every department of the mine.

Jan 1, 2002

By Emil O. Frind, David W. Blowes, K. Ulrich Mayer

The multicomponent reactive transport model MIN3P can be used to simulate the evolution of pore water, pore gas, and the mineralogical composition in mine waste environments. The model is formulated for variably-saturated conditions, considers transport of dissolved and gaseous species, and describes geochemical reactions based on a partial equilibrium formulation. Reaction processes included are complexation, oxidation-reduction, ion-exchange, mineral dissolution-precipitation and gas exsolution- dissolution reactions. An example application, describing the generation of acid mine drainage and subsequent reactive transport for a ID-vertical profile in a tailings impoundment near Elliot Lake, Ontario, is provided.

Jan 1, 2000

By H. Pieterse, K. S. Fraser, J. R. Goode

The Goldstrike autoclave plant is designed for the pressure oxidation of 1363 t/d (1500 stpd) of refractory gold ore. The plant was commissioned in early February 1990 over a one week period - an unusually short period for a plant of this complexity. The rapid plant start-up is attributed to certain detailed design and control aspects of the plant. This paper discusses key features of the autoclave plant with emphasis on the design of the splash/flash system of heat recovery and the control systems. Commissioning and plant operations over the first three months are reviewed.

Jan 1, 1990

By S. K. Kawatra, T. C. Eisele

A horizontal-baffle arrangement has been developed to prevent excessive axial mixing in flotation columns. These baffles have been shown in previous work to improve the grade/recovery performance of both a laboratory-scale column and a pilot-scale column (Kawatra and Eisele. 1993). In this paper, results are given for continuous on-line operation of the pilot-scale baffled column in a commercial coal- cleaning plant. These results show its ability to operate for extended periods without plugging, to produce a consistent-quality product even while the feed quality was fluctuating, and to remove much of the pyritic sulfur from the coal.

Jan 1, 1995

By Carl P. Maronde, William P. Barnett, Patricia A. Rawls

The commercial deployment of advanced fine-coal cleaning technologies depends on cost-effective approaches for efficient separation and ancillary operations in handling, dewatering, drying, and transporting coal fines. As a result of two solicitations under the High-Efficiency Preparation component of the Department of Energy Coal Preparation Program, several projects were initiated for testing and evaluation of emerging technologies and equipment that address operational difficulties associated with coal fines. This paper will update the status of those projects and discuss how the technologies they represent can ameliorate some problems associated with coal fines in today's preparation plants.

Jan 1, 1995

By R. Larry Grayson

A menu-driven, linear-programming- based, user friendly computer program was developed to assist mine managers in determining optimal longwall panel dimensions for a given set of operating conditions. A sensitivity analysis must be performed by varying key mining and configurational parameters over an expected, practical range during the optimization process. Results from analysis of a base case mine indicated that no single combination of longwall panel length and face width is optimal for all operating situations. Each mine manager must therefore look closely at his operating situation and determine the proper dimensions to minimize total mining cost.

Jan 1, 1989

By M. A. S. Martins, J. C. Guillaneau

Steady-state simulation has been proving its usefulness and efficiency in process design and optimization for many years. Steady-state simulation is a very effective approach for plant design since it enables a great number of hypotheses to be considered regarding flowsheet, equipment etc., the processing equipment and material handling equipment to be sized, and the configuration of almost optimal industrial plant to be attained in a very short time. This paper will present the basic principles of mineral process simulation methodology and some real case applications of their capabilities in several complex ores in Brazil.

Jan 1, 1998

By Don W. Murphy, Don M. Larsen

Advanced process control has been implemented at the Jerritt Canyon Mill. Plant production prior to 1997 was limited by grind circuit capacity. The installation of additional mill horsepower and an optimizing supervisory control system achieved a throughput increase in excess of 12 percent. The controller application utilized a seamlessly integrated fuzzy logic expert system for real-time mill control coupled with a neural network predictor for closed-loop feedback of particle size constraints. In late 1998, a second supervisory controller was installed to operate the fluidized bed roasters. The second controller optimized roasting conditions, increased plant throughput and improved metallurgical recovery.

Jan 1, 2000

By T. Tamagawa, S. H. Tabaian, I. Iwasaki, N. X. Fu, M. Kobayashi

A gaseous chlorination process for the hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low-temperature chlorination -selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the process is described. Initially, the chlorination behavior of chalcopyrite concentrate micropellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established were used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 2000

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection systems, the US Bureau of Mines is actively involved in developing a coal rib-thickness monitoring system for high wall mining applications. One particular system that shows promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1996

By C. Bemelmans, L. Chia, T. O’Keefe

Lead alloys function effectively as oxygen-evolving anodes in copper SX-EW operations, and they are highly resistant to corrosion. However, the presence of an organic (from solvent extraction circuits) in the electrolyte seems to enhance solution line attack. Laboratory tests showed that lead is soluble in D2EHPA, Acorga and LIX 984 to a limited, yet measurable, degree. Lead alloys and various lead phases formed on the anode were tested to evaluate their effect on the corrosion process in organic media. Possible causes for anode corrosion and mechanisms responsible for their initiation are discussed.

Jan 1, 1998