Search Documents

By F. Gray

Diamond tool fabricators expect strong growth in most applications for 1995 and 1996. Overall growth projects range from 8% to 10%. Diamond grinding is forecast to grow between 5% and 8%, while cubic boron nitride grinding should grow between 10% and 12%. A strong automotive industry is a major factor in this projected growth, as is continuing demand for other durables

Jan 1, 1995

By Waclaw Dziurzynski, Janusz Tracz, Danny Wooton, Andrzej M. Wala

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By E. Rigopoulos

Mining disturbs the environment, even when the ores or the minerals extracted are non-toxic. Silver & Baryte Ores Mining Co S.A (S&B) is committed to minimizing the environmental impacts of its mining activities, by implementing an integrated rehabilitation program wherever it operates. The paper discusses the principles for mining-disturbed land restoration activities on Milos Island for a successful outcome.

Jan 1, 2003

By W. J. C. Meynink

In drier regions of the world, total containment of cyanide liquors for rainfalls less than a specific design value is often required by government regulation. For example, in Queensland total containment is required for rainfalls up to 'the 1% annual exceedence probability. In equatorial regions, where rainfall greatly exceeds evaporation, a total containment requirement is unrealistic and this is recognized by regulatory authorities. Regulatory constraints typically require that cyanide concentrations at an agreed downstream compliance point not exceed a specific value more than a specified fraction of the time. While the excessive rainfall prevents total containment, it does provide substantial dilution. This paper outlines a methodology for assessing the distribution of cyanide concentrations at a downstream compliance point in an equatorial region with limited hydrometeorological data. Consider the hypothetical mine environs depicted in Figure 1. The mine is located near the catchment divide and draws its water supply via a gravity line. Tailings from the process plant are piped to a tailings dam on a sub-catchment below the plant site. The objective is to determine the distributions of cyanide species concentrations at a compliance point just upstream of a major settlement to ensure they do not exceed regulatory limits.

Jan 1, 1991

By G. Brofas

The reforestation potential of bauxite mining spoils by seeding was examined on this research work. The experimental plot was established on the location Strofi Koukouvista 5, Ghiona Mountain. The experiment consists of 3 species (Pinus nigra, Robinia pseudoacacia, and Spartium junceum) with 4 sowing treatments and 2 sowing seasons (autumn and spring). The treatments were: (1) broadcasting; (2) broadcasting and soil cultivation; (3) broadcasting with straw mulching and straw binding with asphalt emulsion; (4) broadcasting with soil cultivation, straw mulching and straw binding with asphalt emulsion. Third year results show that spring is better than autumn as a sowing season. Only the Spartium junceum species were found to germinate and survive in autumn. The results are better for all the species on the spring seeding. The most effective treatments for Robinia pseudoacacia and Pinus nigra are 3 and 4 while for the Spartium junceum even simple broadcasting shows good results although the best ones are achieved with treatments 2, 3 and 4. The paper?s findings show that reforestation by sowing could be effective for some species but further experimentation with other species is recommended. Concerning Robinia pseudoacacia, testing of different seed preparation treatments is needed in order to maximize the germination of seeds.

Jan 1, 2002

By J. E. Brownhill

After being closed for three years, Specialty Minerals Inc.'s Port Inland limestone facility reopened in the spring of 1992 as a commercial limestone producer. In 1990, Specialty Minerals, a division of Pfizer Inc., bought Port Inland's reserves and equipment from Inland Steel because of the strategic value of the limestone for the production of precipitated calcium carbonate (PCC). Specialty Minerals' project team faced many challenges in reconstructing the Port Inland facility. Many traditions and norms had to be overturned to achieve the productivity, flexibility and cost necessary to survive in today's competitive minerals environment. Port Inland's history Inland Steel built Port Inland in 1930. It was operated as a captive source of metallurgical grade limestone for the steel industry until its closure in 1989. The facility is located in the Upper Pen¬insula of Michigan on the north edge of Lake Michigan. Operations consist of a deep water port facility with crushing, screening and stockpile storage for 453 kt (500,000 st) of finished product at the port. Ninety-nine percent of the stone is shipped by lake boat to ports within the Great Lakes. The operation is unique in that both metallurgical dolomite and limestone are produced on site.

Jan 1, 1994

By J. Loredo

In some rural regions of Peru, artisanal gold mining is currently an essential activity as it provides an important source of income. In the Huanca region (Ayacucho Department) gold deposits are not attractive for mining companies due to their reduced size, but they have enough interest for artisanal mining because of the ease and low cost of mining operations. Artisanal gold mining represents an important damage for the environment, because operations related to amalgamation processes using Hg result in special environmental problems besides the typical ones commonly associated to all mining activities. A preliminary sampling has been made in soils, materials from tailing ponds and surface water of the Acarí River, at the site of the Huanca village, according to networks specially designed for the particular conditions of the area. Studies accomplished revealed high mercury concentrations in soils and tailings. Chemical analyses of soils directly collected in the area of the active or abandoned ?quimbaletes? show mercury concentrations ranging from 15.3 mg?kg-1 to 44.2 mg.kg-1. Mercury concentrations in soils decrease as a function of distance from the before mentioned sources. Water quality of the Acarí River that flows through the area does not present important changes as a consequence of the mining and processing operations.

Jan 1, 2006

By Rolf J. Wesely

Recent events in The Peoples Republic of China indicate that a major effort is underway to increase trade with the western world. Gold production contributes to China's ability to participate in international trade. Consequently, the Chinese government places a high priority on increasing gold production. Many of the operating gold mines in China contain refractory ores that to date have not been efficiently treated. Figure 1 illustrates the description and location of a few of China's major gold mines. China recognizes that the technology necessary to economically treat this ore has been developed in the United States and other western countries. The country has therefore begun to seek assistance in evaluating several potential projects. Organizational structure Gold mining and processing in China is directed by the China National Gold Corp. (CNGC), headquartered in Beijing. The agency has a director in each province who is responsible for exploration, mining and processing. CNGC uses the services of two engineering organizations for metallurgical testing, process development and design engineering for their projects. The largest engineering organization is the Central Engineering and Research Institute for Non-Ferrous Metallurgical Industries (ENFI), also located in Beijing. The second engineering organization is the Changchun Gold Design Institute (CGDI), located in Changchun Jilin province.

Jan 1, 1993

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By Rudolf Greuer, Gerald Jalkanen, Huann-Sheng Chen

A short cut is presented where the average grade above a primary grade cutoff and its associated byproduct grade(s) are estimated by screening the primary and byproduct grades. For the primary variable, choose samples whose grades are above a cutoff of interest. Compute variograms for the subset of the primary variable. Then using this variogram, krige the blocks of interest only using the samples whose grades are above the cutoff. The next step is to screen byproduct grades by choosing byproduct samples whose associated primary grades are above the cutoff of interest. Next compute variograms for this subset of byproduct samples. Then using this variogram, krige the blocks of interest using byproduct sample grades whose associated primary sample grades are above the cutoff of interest. The results are the average grade above a primary cutoff for both the primary and the associated byproduct variables. Using two simulated primary and reference data sets a case study resulted in the screening krigings performing better than the indicator kriging approach in the first case study. A second case study had mixed results with the primary indicator approach performing better than the primary screened approach. The byproduct screened approach performed better than the byproduct indicator approach.

Jan 1, 2002

By W. E. Horst

Raw materials and mineral products are crushed, ground, or pulverized for a variety of reasons. Some of the most important reasons for size reduction are: to liberate marketable mineral species from a matrix of commercial minerals and gangue, to promote rapid chemical reaction through exposure of large surface area, and to produce a material with desirable size characteristics for handling, utilization, and storage. Comminution processes are currently used on vast tonnages of raw material annually. In the mineral industries where mineral products and other solids are processed, the various size-reduction unit operations represent a major portion of the manufacturing costs. The comminution process is an expensive unit operation from the stand- point of both capital and operating costs. Power consumption is large, and the energy conversion to useful work is very small regardless of the size-reduction system. In energy terms, about 1% of the all electricity generated throughout the world is expended in crushing and grinding operations by the cement industry alone. Comminution is a general term for size reduction that may be applied without regard to the actual breakage mechanism involved. General type of size-reduction equipment include crushers, tumbling mills of various type, impact mills, fixed-path mills such as a roller mill, and fluid-energy mills. Some comminution machines accomplish

Jan 1, 1985

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989

By Michael E. Kelahan, Charles Y. Guan, Glenn A. Gruber

A comparison of the IMC Anionic Process and the CLDRI Process, based on pilot plant testing of waste pebble by Jacobs Engineering is presented. Estimated costs for constructing and operating a beneficiation plant utilizing dolomite flotation are given. Research to develop practical flotation processes for removing dolomite from low-grade phosphate rock has been a high priority for the Florida Institute of Phosphate Research. The Institute funded the above pilot plant programs in 1998 and 2000. The Florida Phosphate industry currently deals with the increasing dolomite content of ore reserves by practicing selective mining. Heavy media separation plants installed at two mines to remove dolomite from pebble are not being operated. The flotation separation of dolomite from waste pebble requires that the flotation feed be ground. Grinding liberates the mineral species and produces particle sizes small enough to be floated. Only two dolomite flotation processes, the IMC Anionic Process and the CLDRI Process, have been successfully demonstrated on flotation feed that has not been deslimed after grinding. Deslimed flotation feed, relative to undeslimed feed, has improved flotation performance and reduced reagent consumption. However, for the above mention processes, undeslimed ground feed increases the yield of concentrate because the phosphate desliming losses are avoided.

Jan 1, 2002

By R. C. Oberth, C. F. Lee, E. M. Taylor

INTRODUCTION Underground siting of nuclear power stations is drawing increasing attention in various parts of the world. Scandinavian countries took the early lead in this field because of their experience in the design and construction of underground hydroelectric stations and industrial plants, and because they have near-surface rock formations which are ideally suited for hosting large underground caverns. The world's first underground nuclear facilities were built in Norway (Halden) and Sweden (Agesta) and were commissioned in 1959 and 1963 respectively. Figure 1 summarizes the main features of these and two other small-scale European facilities. (1-4) American utilities and regulators are also for a variety of reasons assessing the benefits and penalties of underground siting. A recent study by Sandia Laboratories (contracted by the Nuclear Regulatory Commission (NRC) focussed on identifying potential safety benefits of underground siting. (5) Although the study concluded that underground plants would have improved containment for some accidents, as well as better external protection, NRC, in assessing the overall benefits and penalties, decided not to impose mandatory underground siting for nuclear stations. In June 1976, the California Legislature enacted a law which directed the California Energy Commission (CEC) to examine the issues concerned with underground siting of

Jan 1, 1979

By P. Somasundaran, S. E. El-Mofty

A comparison of the IMC Anionic Process and the CLDRI Process, based on pilot plant testing of waste pebble by Jacobs Engineering is presented. Estimated costs for constructing and operating a beneficiation plant utilizing dolomite flotation are given. Research to develop practical flotation processes for removing dolomite from low-grade phosphate rock has been a high priority for the Florida Institute of Phosphate Research. The Institute funded the above pilot plant programs in 1998 and 2000. The Florida Phosphate industry currently deals with the increasing dolomite content of ore reserves by practicing selective mining. Heavy media separation plants installed at two mines to remove dolomite from pebble are not being operated. The flotation separation of dolomite from waste pebble requires that the flotation feed be ground. Grinding liberates the mineral species and produces particle sizes small enough to be floated. Only two dolomite flotation processes, the IMC Anionic Process and the CLDRI Process, have been successfully demonstrated on flotation feed that has not been deslimed after grinding. Deslimed flotation feed, relative to undeslimed feed, has improved flotation performance and reduced reagent consumption. However, for the above mention processes, undeslimed ground feed increases the yield of concentrate because the phosphate desliming losses are avoided.

Jan 1, 2002

By D. A. Curry

This paper describes a study of the influence of non-normal loading on the indentation behaviour of single bit-teeth. Indentation experiments have been performed on a soft, isotropic limestone using both sharp and blunt 60 degree wedge-shaped indentors constrained to penetrate the rock at 0, 15, and 30 degrees to the rock surface normal. For both sharp and blunt indentors, the normal force required to produce a given normal penetration decreased as the offset of the penetration direction from the rock surface normal increased. The crater volume produced by a given normal penetration with the sharp indentor was largely independent of the penetration direction. In contrast, the crater volume produced by the blunt indentor was increased markedly by non-normal penetration at small penetration depths, because the threshold penetration for chip formation decreased with non-normal loading. The crater volume produced by a given normal force was significantly increased by non-normal penetration, and this increase was particularly pronounced with the blunt indentor. The energy required to form unit crater volume was correspondingly reduced by non-normal indentor penetration. A simple method for predicting the reduction in the rock's resistance to chip formation is outlined, which is supported by the experimental data. The implications of these findings for rotary drilling are considered.

Jan 1, 1986

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By C. H. Lee, F. Concha, L. G. Austin, P. T. Luckie

The Concha-Almendra batch-settling treatment for concentrated suspensions of single-diameter spheres has been modified. This modified version is used in the differential equations of simple batch settling of a particle size range of different density materials. The equations have been programmed for a finite difference solution, and a number of test cases have been analyzed. By cutting the settling column at a fixed fractional height, the material below this height can be treated as underflow and the material above as overflow. The predicted partition curves obtained from treating the settling in this way have Sharpness Indices in the range of 0.5 to 0.6, in the absence of dispersion effects. The Sharpness Indices decrease as dispersion increases. When the feed size distributions are of the Rosin-Rammler form, the partition curves (corrected for the bypass fraction) fit the Rosin-Rammler equation with reasonable accuracy. The predicted Sharpness Index of a component of a mixture of two materials of different densities was unchanged from that of the same materials settled alone. However, for the same, feed size distribution and volume fraction of solids in the feed, the heavier material settled faster, and the lighter settled slower, than when settled alone.

Jan 1, 1993

By K. Biswas, S. S. Peng

The stability of pillars in old mined-out districts is greatly dependent on the weathering action caused by moisture penetration into the pillar structure. Field observations in old mining districts indicated that this weathering action becomes critical in terms of the stability of the pillar if the coal seam contains parting or binder (layers of claystone or mudstone). The weathering action caused by moisture penetration over a long period of time degrades both parting and coal. However, it has been observed that the structural deterioration is more severe in parting. Moisture-penetration rates in parting and coal are different. The extent of the weathered zone in various layers of the pillar is primarily time dependent. This paper investigates, both in the laboratory and in the field, the effects of weathering action on coal and parting. In the laboratory, slake durability indices and uniaxial compressive strength tests for dry and saturated specimens are compared for coal. In the field, the in situ strength profiles for coal and parting layers are obtained, and the effect of time (in terms of the pillar age) on the strength profiles is studied An attempt was also made to establish formulae for time-dependent strengths of coal and parting.

Jan 1, 2000