Search Documents

By Robert K. Towner, Francis S. Kendorski

Shotcrete drift linings at the Climax Mine of the Climax Molybdenum Company have undergone four years of extensive evaluations as a replacement for thick poured-in-place concrete linings. Any drift lining at Climax must be able to withstand the rigors of undercut and secondary blasting, weight problems induced by panel caving, and the abrasion of slusher mining. Examined here are the conclusions reached so far on shotcrete drift linings which have not yet completed the approximately six-year cycle from development to ore exhaustion. Properly applied shotcrete is an adequate drift lining for all phases of the Climax panel caving system of mining. Undercut blasting will damage shotcrete unless blasts are correctly timed. Weight problems will destroy shotcrete drift linings as efficiently as it will destroy concrete or steel support systems. Abrasion and secondary blasting results are inconclusive as the shotcrete lined slusher drifts have not entered the ore production stage of the mining cycle. In addition to drift linings, Climax has found shotcrete to be invaluable for lining large underground shops, for temporary support systems, for permanent ventilation bulkheads and for the repair of abraded or weight damage concrete lined slusher and haulage drifts.

Jan 1, 1974

By J. Bigu

A theoretical radiation mine model, suitable for underground uranium nines, has been investigated. In this model, the rate of ventilation and/or the radon (thoron) gas emanation from mine walls are time-dependent. Several cases of practical interest have been investigated including sinusoidal, linear, exponential, stepwise, or a combination of two or more of the above. Analytical solutions were obtained for the time-dependent radon (thoron) gas emanation rate. However, because of the extreme analytical complexity of the solutions corresponding to the time-dependent ventilation rate case, numerical solutions were found using a special Runge-Kutta procedure and the Hamming's modified predictor-corrector method for the solution of linear initial-value problems. The mine model makes provisions for losses of radioactivity, other than by ventilation and radioactive decay, by, say, plate-out on mine walls, and by other mechanisms. Radioactivity data, i.e., radon, thoron, and their progeny. obtained with the above mine model for a number of ventilation and emanation conditions, are presented. Experimental data obtained in an inactive stope of an underground uranium mine for a time-dependent air flow case are shown. Air flow conditions (ventilation rate) were determined by tracer gas techniques using SF6.

Jan 1, 1987

By J. Twining, V. Nguyen, J. Perera

A computer code for ecological risk assessment (ERA), AQUARISK, has been developed and applied to evaluate the likelihood of biotic detriment due to exposure to acid rock drainage (ARD) from the Burkunga mine site in Australia Stream water quality monitoring data were used for the assessment and were compared with a) national water quality guidelines, b) literature derived ecotoxicology data and c) biological monitoring data. With bioavailability calculations, the code predicted that, for metals exceeding the guidelines, 44% of macroinvertebrate species above the mine and 100% below the mine would be adversely affected by the metals in the stream. This compares reasonably and conservatively with biological monitoring that showed observed reductions of 41% and 85% of species respectively at each site. Using literature data for macroinvertebrates to predict impact produced similar estimates to using data for all taxa. Use of speciation modeling also lessened the degree of reduction in the median water metal concentrations required to achieve acceptable impact (measured either by exceedence of criteria or by species likely to be affected) by a factor of 75%. This result implies significant economic and management benefits in relation to remedial engineering or water treatment options for sites.

Jan 1, 2000

By Frits Agterberg

Statistical exploration uses statistical methods to identify targets for more detailed investigation by estimating the odds of occurrence of mineral deposits. The study area which contains the possible targets may be as large as 1 000 000 km2 or as small as 100 km2. Results are presented in terms of a probability index for the existence of a deposit or, more precisely, in terms of expected dollar value for a unit area, or even in terms of number, size, and grade of deposits remaining to be discovered. Typically, selected geological, geophysical, or geochemical information is systematically quantified and statistically analyzed by using the computer in order to distinguish between geological environments on the basis of the probability that they contain undiscovered deposits of a specific type. All possible targets are compared with one another by using information on areas known to contain deposits. The information on the known areas is either a set of control data consisting of values for the same parameters as are quantified for the entire study area, or it embodies a specific model for the occurrence of a given deposit type. Examples of both procedures will be discussed in this chapter.

Jan 1, 1979

By Ammar Henchiri

INTRODUCTION A current need of the phosphate industry is the development of process technology for treatment of high carbonate content ore. About 75 to 80 percent of the world phosphate reserves (1) are associated with carbonate gangue, which is not amenable to treatment by the existing techniques. Numerous laboratory and pilot plant studies have been devoted to carbonate-phosphate separation. Different techniques were involved (washing, sieving, attrition, flotation, calcination, and leaching). For technical and economical considerations, flotation appears to be an efficient process for this problem. Separation of carbonates (calcite and dolomite) from igneous phosphate is applied in industrial plants in Brazil, Finland, and South Africa. But, for sedimentary phosphate, no industrial realization exists at this time, with the possible exception of some plants in China. The main problems with sedimentary phosphates are: • high substitution by CO3-2 and F- for P04 -3 in the apatite lattice. • larger surface area of the phosphate particles because their surface is porous and irregular. • tendency of sedimentary minerals to produce more slimes in conditioning than the crystalline minerals, hence, larger dosages of collectors are required for sedimentary minerals. Investigations reported in the literature indicate that most processes developed for sedimentary carbonate-phosphate separation involved inverse flotation of carbonates using fatty acids as collectors (2), (3) associated with phosphoric acid (4), monosodium phosphate (5), F- (6), or SiF6 -2 (7) as phosphate depressants. Later investigations, conducted by A. Henchiri and G. Baudet (8), (9), (10), (11), (12), (13) in the BRGM technology department, of phosphoric esters revealed that these reagents are selective collectors for carbonate-phosphate separation. The above investigators developed a process which used phosphoric esters to collect carbonate minerals and sulfuric acid or sodium fluorosilicate as depressants for phosphate. Extensive comparative tests for different processes on the same phosphate sample show that the process developed at BRGM is one of the most promising methods proposed for sedimentary phosphate-carbonate separation. It should be pointed out, however, that phosphoric esters make abundant froths. The handling of these excessive froths will be a problem in an industrial-scale plant. This paper outlines test work performed in order to optimize and to improve the efficiency of the flotation process on a sedimentary phosphate ore selected from the Sra Ouertane orebody. The Sra Ouertane flotation process, illustrated on Figure 1, first removes carbonate minerals by inverse flotation and then recovers phosphate as a froth product, leaving quartz as a cell product.

Jan 1, 1993

By James R. Oehler

Progress, future challenges, and the continual search for more efficient and rapid methods of excavating underground openings and shafts were main themes at the 1983 Rapid Excavation and Tunneling Conference (RETC) held June 12-16 in Chicago, IL. The event, jointly sponsored by the Society of Mining Engineers, the American Society of Civil Engineers, the Canadian Institute of Mining and Metallurgy, and the Engineering Institute of Canada, offered a diverse program for both civil and mining engineering disciplines. Although all papers given at the three-day conference were noteworthy contributions, and each is included in the conference proceedings currently available from SME, there were a few sessions that had particular mining-related interest. Research, Acceptance Needed for Water-Jet Technology Water-jet-assisted rock excavation is seen by some as a technology moving from the prototype phase to a fully developed, accepted system within the next decade. For an industry that is traditionally fairly slow in accepting significant changes, this development appears especially noteworthy. However, speakers at the water-jet technology session generally agreed that many large US manufacturers are not viewing water-jet-assisted equipment as viable replacements for all-mechanical systems. This, they fear, may mean some US manufacturers will lose a significant share of certain equipment markets to foreign competitors who are moving aggressively ahead in this area. Despite the advantages of increased cutting rates, reduced power requirements, less dust, prolonged bit life, and reduced sparking in many cutting situations, water-jet technology applied to mining is apparently having some acceptance problems in the US. R. J. Evans, professor of industrial engineering at the University of Pittsburgh, noted that there are several perceptual barriers to water-jet coal cutting; such as uncertainties concerning the fu¬ture demand for coal and the reliability of equipment, apprehensions that jet-assisted equipment will make the mine operator dependent on specific types of hard-to-obtain equipment, and fears about accessibility of the equipment for repairs. Evans also said numerous parameters need defining before taking advantage of water-jet-assisted cutting systems in under-ground coal mining in the US. For the cutting head, information must be obtained on optimum bit geometry and spacing, and maximum and minimum torque requirements. For a complete US water-jet cutting system, Evans added, research is needed to establish optimum jet pressures, jet powers, number of jets per bit, and location of jets relative to the bit. One research project making progress towards optimizing parameters for a water-jet-assisted drag bit cutting system for coal mining was described by Levant Ozdemir, director of the Earth Me- .

Jan 8, 1983

By J de Cuyper, G. Rinelli, A. M. Marabini, V. Alesse, W. Freyberger

Salicylaldehyde, a chelating agent for tin, has been found to function as a collector for the flotation of cassiterite. Infrared and nuclear magnetic resonance studies clearly show that salicylaldehyde can form a chelate compound in bulk and at the surface. Results are also given for the flotation of a tin ore with this reagent.

Jan 1, 1976

By R. C. Bryan, D. B. Jamison

This paper describes a procedure for minimizing the operational costs associated with blending sodium in coal at a surface mine in the Powder River Basin. Mine site blending is performed by adjusting daily production rates for high- and low-sodium pits. These adjustments are designed to produce a consistent sodium value called the blending target. The mine's contractual limit for sodium is sufficiently close to the field average value that any decrease in the sodium blending target may result in an opportunity cost, if the number of potentially minable tons is reduced. Conversely, any increase in the blending target may result in a higher sampling cost if more information is required to keep the blend within contractual limits. Blending parameters were defined using a geostatistical block model of sodium content that was based on analyses of hundreds of in-pit sample holes. Variograms for these data were used to compute the marginal costs of opportunity and sampling for a series of hypothetical in-pit drilling patterns. These marginal costs provided a basis for selecting optimum values for key parameters such as the blending target, production variance and in-pit sampling density. The benefit of implementing these optimized parameter values is that operational costs of sodium blending will be minimized over the long-term. At the mine where this procedure was developed, each dollar spent to increase the sampling density to the optimum value was shown to generate a $10 savings in opportunity cost.

Jan 1, 1991

By R. V. Ramani, W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of low-temperature, radio-frequency ashing (LTA) and infrared analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods. In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1996

By R. L. Murray-Smith, M. E. A. Robertson, M. J. Prosser

The AZTEC is an automated instrument, for the non-destructive analysis of gold ore samples, which uses energy dispersive X-ray fluorescence (XRF), This is achieved by X­ray tube excitation of gold K X-rays. The first production instrument was commissioned at Vaal Reefs Chemical Laboratory (VRCL) in November 1987, followed by two second generation instruments in 1989. AZTECs have also been installed at Western Deep Levels and at Anglo American Research Laboratories (AARL). A further unit is being assembled at Ashanti mine, Ghana. At VRCL the AZTECs are used primarily for the evaluation of mine (stope) samples. Each of the production instruments can routinely analyse 650-700 samples per day, with the aid of a robotic sample transfer system. Various techniques have been evaluated for increasing sample throughput. For example, higher value samples can be counted for a shorter time to obtain the necessary relative precision.

Jan 1, 1991

By Silvia H. M. Grimaldi, Afonso H. Martins

The scope of this experimental work was to study the yttrium extraction and stripping behaviour in a solvent extraction system with mono(2-ethylhexyl)2-ethylhexylphosphonic acid (IONQUEST 801) in a chloride system The study was performed for only one contact between organic and aqueous phases The experiments were carried out according to a factorial design. Due to the statistical analysis and its experimental proof, the optimum conditions for maximum yttrium loading into the organic phase of the extraction stage were 16 minutes for time of contact between phases, 980 rpm of stirring intensity and pH=2.3 for the aqueous phase of the sovent extraction system. The optimized experimental conditions by the statistical approach for the stripping stage were: time of contact between phases equal to 20 minutes, 1050 rpm of stirring intensity and 1.75 M HCI into the stripping aqueous solution.

Jan 1, 1995

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By Peter A. Spencer

Much criticism has been levelled at bacterial oxidation over the quantities of air required for successful operation. Examination of the oxidation reactions and the assumptions concerning oxygen transfer made in the literature (1) indicate that the aeration requirements can be much less than those beirig suggested. Observations made on a large scale pilot test have confirmed reasonable aeration levels in extended site operation over a six month period. These aeration levels have implications for the engineering design and the power needed for aeration and agitation. Thus, these parameters effect both capital and operating costs as well as influencing the complexity of the design and normal operation. A number of companies have developed bacterial oxidation cultures intended for commercial ·expl oi tat.ion ( 2, 3, 4). Most of these cultures have been based on Thiobacillus and operate at temperatures between 30°c and 40°c. This temperature range limits their application in hotter regions unless means for both heating and cooling are provided in the design. Thiobacil!us cultures are also reported as not able to oxidize arsenic (III), which may limit the application of these cultures to successfully treat arsenopyritic ores and concentrates (5). BacTech (Australia) Pty Ltd has developed a culture which operates at temperatures above 4o0 c and which has been tested in a large site based continuous pilot plant at up to 55°c over a six month period. The culture showed resistance to high levels of soluble arsenic, allowing the arsenic to be retained in solution for control led precipitation and disposal. Data for. the arsenic precipitates indicated that these waste solids were relatively stable and, under the correct circumstances, were suitable for disposal into tailings dams without causing environmental problems.

Jan 1, 1990

By S. Ford

The introduction of recent advances in molecular biology into the field of microbial ecology has made available a powerful set of analytical tools for dissecting the structure of microbial communities in natural environments. The use of these approaches, many of them based on DNA-DNA hybridization enables the researcher to assess the occurrence of specific DNA sequences among the natural bacterial flora (Ford and Olson 1987). These techniques promise to have wide application as tools for monitoring the spread of introduced microorganisms (Trevors, 198'): Ford and Olson. 1987) and have been used to examine the response of bacterial communities to environmental contaminants and stressors (Barkay and Olson. 1986. Olson and Ford. 1986. Olson. Ford and Lester 1987) The occurrence of heavy metal resistance among microorganisms has been discussed as a possible tool for the detection of pathfinder elements employed in mineral exploration (Olson and Barkay 1986). In addition, the occurrence of heavy metal resistant bacteria may be utilized in protocols for assessing the occurrence and biological impact of contamination occurring as a consequence of mining operations. In this context the use of DNA hybridization technology enables the investigator to directly quantify the number of heavy metal resistant bacteria by the use of genetic probes specific for those resistance genes. The implementation of a strategy for detection of heavy metal resistance genes by hybridization technology is dependent on the availability of data on the genetic systems which encode resistance The availability of extensive DNA sequence data on mercury resistance genes (Brown et a11986. Barrineau et al 1984) has lead us to use gene probes specific for mercury resistance within natural bacterial populations as a model system for investigating the response of these bacterial populations to the occurrence of mercury In the environment.

Jan 1, 1988

By D. M. Sloan

While surety capacity for the mining industry continues to shrink, States are demanding greater financial certainty for closure/post closure obligations. To combat these demands, larger mining companies are pursuing a Mining Surety Reinsurance Program that requires a significant up front capital contribution. This paper outlines an alter-native program for middle market mining organizations. The program utilizes a “Blended Finite Risk” environmental insurance solution with surety acting as the “front” in states where insurance is not an acceptable form of collateral. Marsh proposes creating separate programs for each State requiring surety. The reason for separate programs stems from each states’ different surety rules. Insurance companies typically require at least $5 million in future value remediation liabilities for finite risk programs. Since most middle market mining companies have obligations that fall below this threshold, the Blended Finite Risk Program contemplates combining several companies closure/post closure liabilities to accomplish the minimum amount required by the insurance company. Why use a Blended Finite Risk Program? One of the primary benefits is the financial assurance that funds will be available for planned remediation. For example, the financial assurance may be required by a government agency. The certainty may help facilitate a merger or acquisition. Additionally, the funds may be part of a CER-CLA PRP settlement. In all cases, the insurer providing coverage would be a secure independent 3rd party. A Blended Finite Risk Program also provides a long-term solution – up to 30 years and in some select cases longer. The benefit to a state or the BLM is the removal of financial uncertainty. An insurance company writing the policy would have an AA or AAA balance sheet. The hardening of surety markets coupled with the tightening of financial assurance requirements in many states have necessitated the posting of 100% collateral. This program substantially reduces these collateral requirements.

Jan 1, 2004

By R. A. Hodge, J. W. Murray

By an order of the Executive Council of the Provincial Government dated January 18, 1979, a Royal Commission was established under the Public Inquiries Act to: 1) Examine the adequacy of existing Federal and Provincial requirements for the protection of the health and safety of workers associated with exploration, mining and milling of uranium in B.C. and for the protection of the environment and of the public. 2) Receive public input on these matters. 3) Make recommendations for setting and maintaining standards for worker and public safety and for the protection of the environment as a result of the exploration for the mining and milling of uranium ores. At that time,and at the present time in British Columbia, no uranium mines were, or are, in operation. Exploration at a number of sites was under way and one deposit, the Blizzard deposit, with estimated reserves of 1.92 million tonnes containing approximately 4.74 million kilograms of U308 was at an advanced stage of exploration. With our Terms of Reference, and because of the diverse geology of the western Cordillera which could potentially host a broad variety of uranium, deposit types, the Commission was faced with the task of considering environmental and health protection necessary for the potential development of [any] kind of uranium mineralogy situated in [any] of the environments found in British Columbia. Over the past 17 months since that time, much has transpired, culminating in the February 27, 1980 Provincial Government announcement of a seven year moratorium on exploration, mining and processing of uranium coupled with the termination of our Inquiry before completion of the hearings. The Government sebsequently modified its decision to terminate the Commission completely, deciding instead to stop the hearing but allow time for the Commission to gather in the work that had been initiated

Jan 1, 1980

By H. J. Chen, Y. Luo, S. S. Peng

Surface subsidence resulting from underground coal mining can cause problems for buried pipelines. In this paper, a technique for assessing the level of stress on a subsidence-affected pipeline is introduced. The main contributors to the stress are identified, and mitigation techniques for reducing the stress are proposed. The proposed mitigation techniques were then successfully tested.

Jan 1, 1998

By Erik Westman, Benjamin Mirabile

"Ongoing research is being conducted to evaluate secondary support performance in longwall ventilation entries. In a three-entry longwall gateroad, secondary supports are applied in the #2 entry to maintain a functional airway for the entirety of second panel mining. This airway represents a pathway for contaminated mine air to travel from the longwall tailgate to the mine bleeder system. The ground response curve concept may be used as a design basis for selection of appropriate secondary support in these ventilation entries. Two types of secondary supports are monitored for load and convergence in this project. These monitored supports are pumpable crib supports and interlocking wood crib supports. To evaluate the effect of support density, two installation patterns are monitored for each support type. Both a single-row, protected airway pattern and double-row, full entry support pattern are monitored for each support type. Load and displacement data is collected for all support patterns as second panel mining retreats past instrumentation sites. Data is collected for approximately 200-feet inby the second panel face or as long as safely possible. Load and convergence data collected will be used to calibrate numerical models that will simulate ground response curves for the #2 entry inby the second panel face.INTRODUCTIONWhen a bleeder ventilation system is used, the #2 entry of a three-entry longwall gateroad system is designed to function as a pathway for contaminated air from a longwall face to the bleeder system during second panel mining. The #2 entry is subject to substantial ground movement and loading during its function as an air course because it is a single entry between two longwall gobs. Secondary support is regularly applied in this entry to maintain air course functionality during second panel mining.Research on performance and design of secondary supports has been conducted extensively over the last 30 years (Barczak and Gearhart, 1993; Barczak and Gearhart, 1994; Mucho, Barczak, and Dolinar, 1999). This research has focused heavily on the application of secondary support in longwall tailgate, with little research on the application of secondary support in bleeders or other ventilation entries (Mirabile and Westman, 2018). Secondary supports in #2 entry are likely to experience similar loading and ground movement as those applied in the tailgate entry. However, the designed lifespan of the mine entry and the definition of acceptable ground conditions differs from mine entries where more extensive research has been conducted."

Jan 1, 2019

The research deals with the study of the quality indicators in the productive process and its use for the consuming market, for two types of ores: industrial sand and crushed stone. Companies who represent the profile of the São Paulo producing market in its respective modalities well produce the selected cases. The development of the studies have to be, for the application of consistent methodological models of the fundamentals of the Engineering of Quality, especially how much to the statistical control of processes and its trustworthiness, of form that the results of the research can serve as referential in the boarding for other generic cases of the mineral industry.

Jan 1, 2003

By P. Bevilacqua, G. Vallebuona

Empirical models are now used for predicting the performance of hydrocyclones in terms of capacity. cut size (d50.c), water split and partition curve. These models (such as the model by Lynch and Rao and the model he Plitt) were developed and checked for hydrocylones with diameters larger than 4 in. However, for smaller-diameter hydrocyclones, little empirical modeling has been done. This paper reports on an extended experimental research program on small hydrocyclones. For these cyclones, the suitability of existing empirical models was investigated and their accuracy was compared. To improve the predictive capability of these models to small cyclones modifications to the equations are proposed.

Jan 1, 1996