Search Documents

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By Keiichi Fujita, Katsumoto Ueda, Hiroshi Nakauchi, Naohiko Okumura

INTRODUCTION This paper presents (1) modified slipform system which was employed for simultaneous concrete placement for permanent lining and Instruction of a partition wall in the execution of a ventilation shaft 620m deep, and (2) current shaft sinking techniques which have been applicable and efficient for the subsurface conditions in Japan. MODIFIED SLIPFORM SYSTEM FOR PERMANENT LINING OF VERTICAL SHAFT General Information This paragraph deals with rapid construction by using modified slipform system for the permanent concrete lining and a partition wall of ventilation shaft, which has inside diameter of 620m and depth of 620m, of Enasan Highway Tunnel. The general feature of the shaft is illustrated in Fig. 1 and standard section of the shaft is illustrated in Fig. 2. The geological condition surrounding the shaft is mainly of ryolite and surface is of talus, but as a whole, they are rather weak and weathered rocks with faults, fissures and clay seams. 220mm borehole for the geological investigation was used as a drainage hole, predicting the amount of water inflow into the shaft to be 10t/min. The shaft was executed mainly by means of the conventional short step sinking method of 1.2m lift, employing temporary headframe and hoists. For each lift, 40 to 50cm thick temporary concrete lining was used. About 28,600m3 of rocks were excavated and

Jan 1, 1979

By Alva L. Kuestemeyer, Randall J. Scott

INTRODUCTION Pincock, Allen & Bolt, Inc. (PAH) has developed a series of cost models for Western U.S. Gold Mines. The models indicate the economic potential of developing gold properties at various production rates and ore grades. Various combinations of mining and processing methods are also analyzed. The conclusions shown in this paper are taken from PAH's 600 page study titled, "Capital and Operating Cost Models for Western U.S. Gold Mines." PAH decided to develop the cost manual as a result of our perception of the industry's need for such a document. It was our impression that exploration development decisions were being made on the basis of limited economic information. PAH has compiled a substantial database on unit cost information. That database and the engineering capabilities of the firm allowed us to develop a reasonably detailed analysis of capital and operating costs and overall development economics. The study has developed a series of algorithms for underground and open pit mining, processing, G&A, and infrastructure costs. The capital and operating cost data served as a basis for performing after tax discounted cash flow analysis for the various development alternatives. For the base case scenarios, a 15% DCFROR was assumed and the required ore grade was back calculated using the computer. The ore grade versus production rate graphs summarize the economics of developing gold projects in the Western U.S.

Jan 1, 1987

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989

By J. A. Ryder

Compressed air is a relatively inefficient yet very convenient vehicle for transmitting mechanical energy. It is inefficient when compared to, say, hydraulic or electric energy systems since compressor and pneumatic machine efficiencies are quite low (in the range 20-65%) and reticulation losses can be quite high unless adequate pipe diameters are used to minimize friction drops. It is convenient in that capital and maintenance costs of pipes and machines are exceptionally low, the equipment is flexible and lightweight, the technological level is simple, the form of the energy supply is intrinsic- ally safe, and as an additional minor but psychologically important benefit, it provides a ready source of cooling and air supply for emergency use in deep hot mines. It is for these reasons that compressed air is a premier source of energy for many forms of underground equipment, in particular hand or rig-mounted rockdrills, some forms of rock- handling equipment, and a host of minor applications including agitators, small-lift pumps and temporary f am installations. In a typical S. African deep-level gold or platinum mine, compressed air generation accounts for 15% of the total mine electrical energy bill - more than is used for hoisting. In these mines it is not uncommon for over 100 km of underground compressed air piping to be installed, primarily to supply handheld rockdrills.

Jan 1, 1979

By Tony Treasure, Ian Ewart

The EMEW® cell has been developed to overcome a number of inherent limitations in conventional electrowinning technology, particularly the high cost and restricted process windows characteristic of conventional hardware. The EMEW technology has been widely demonstrated to achieve high performance for various metals under chemical conditions well outside the limits required for efficient operation of conventional cells. In particular application of the EMEW cell for recovery of silver offers significant operating and capital cost advantages over conventional Merrill Crowe technology used for cyanide based solutions. The cell also offers process advantages for direct silver recovery from nitric acid solutions. The performance of the EMEW® cell on silver cyanide solutions, producing high grade silver metal in a single step, is accomplished by providing a physical mechanism which presents metal ions to the cathode on a highly efficient and continuous basis. The simplicity of design and operation of the EMEW cell offers the following advantages for silver recovery from cyanide or nitrate based solutions: • High grade product in a single step. • Selective for silver over other metals in the electrolyte. • Wide operating concentration range (100,000 - 5ppm). • Ability of the cell to operated in a variety of acid or alkaline electrolytes. (Cyanide, Nitrate). • Simple liquor reticulation. • No pretreatment required - Clarification, deaeration or zinc dust. • High cmTent density and current efficiency compared to conventional electrowinning cell. • Modular design allows for flexible operation and production rate. • Pilot plant results using full scale cell result in accurate scale up design. • Easy/fast installation - cell banks are delivered pre configured with piping and wiring. • Enclosed cell minimizes corrosive vapor and liquid losses in the circuit.

Jan 1, 2000

By A. Frederick Banfield

Various modeling techniques are available for describing ore deposits on the computer. Multiple seam coal deposits can be quite successfully modeled by using the variable block modeling method. In essence, this type of model provides an efficient method for storing the relevant data required for calculating ore reserves and for performing the mine planning. The main advantages of the variable block model over other methods for modeling irregular block or tabular deposits are: 1) The amount of data that has to be stored is minimal, i.e., the most efficient use of computer space is made since only the pertinent seam and topographic geometries need to be stored. 2) The computer logic necessary for calculating ore reserves and performing mine sequencing is relatively simple as compared to the logic that would be required for the three-dimensional block model. 3) A variable block model can be created either by starting from raw drill-hole data or by digitizing cross sections that contain the geologic interpretations. 4) Updating individual or multiple blocks can be performed with relative ease. 5) Display of the model is relatively inexpensive and easy to perform. The objective of this chapter is to describe a developed procedure as used in applying the variable block model to a specific multiple seam coal deposit. The general sequence of operations includes: (1) develop the computer model, (2) design the open-pit limits, (3) compute reserves, and (4) develop a long-range mining plan. The programs developed for this application are an expansion of MINTEC's MEDSYSTEM software. It should be noted that this is just one of many possible applications of the developed variable block model.

Jan 1, 1979

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

By Vladimir Adamek

Due to the variability of subsidence characteristics across the U.S. coalfields, it was concluded that it would be practically impossible to develop a universal predictive model for mining-induced subsidence based on theoretical assumptions. Therefore, an effort was made to find a procedure to develop an empirical subsidence predictive model based on a sufficient Mount of field data from one mining area (in this case the Northern Appalachian Coal Region). It was also thought that this procedure, if successful, could be used as the template for developing predictive capabilities for other coalfields with different subsidence characteristics given a reasonable amount of field data. It has been found, in the Northern Appalachian Coal Region, that the variability of subsidence characteristics can be expressed by a polynomial equation developed through regression analysis of the variable subsidence coefficient and derived directly from the field data. In this study, field data were obtained from 11 Bureau longwall panel studies (16 half profiles) for static subsidence and 14 panels for dynamic subsidence. The effects of lithology, expressed in the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hythetically homogeneous overburden and existing ithological conditions. For each longwall panel, the characteristic of the variable subsidence coefficient was defined along individual static profiles. The definition of mean values with acceptable deviations is the substance of the predictive method. The same procedure was used to develop a predictive model for dynamic subsidence, since it war discovered that the rate of longwall face advance is not a necessary functional parameter. This paper presents the theory, development, and application of the static and dynamic subsidence prediction models.

Jan 1, 1986

By Malcolm J. Lake, P. Brad Marchant, Linda M. Broughton

Thiourea is recognized as a technically competitive alternative to cyanide for gold and silver extraction for a variety of ores and concentrates. This paper describes the results of a recent mini-pilot locked cycle test comparing cyanidation with acidothioureation treatment of gold bearing sulphide concentrate. The gold extractability of both methods was similar. The comparative metallurgical operating conditions and test results are summarized. Detailed byproduct solution analyses and environmental toxicity test results are presented and suggest that thioureation might result in acutely toxic byproducts even after treatment. Comparative process economics are summarized based on preliminary commercial operating flowsheets derived for the locked cycle case study. Capital and operating cost estimates are shown. The results indicate that cyanidation is more economically favorable within the constraints of the case study. Considerations for process selection between thioureation and cyanidation, for conceptual case studies, are discussed.

Jan 1, 1998

By V. Fred Swanson, J. Patrick Glynn

The environment for process engineers today is very different from 20 years ago. The ideas and mathematical description of models for a multitude of different unit operations is an ongoing development. The computer tools to deal with the mathematics are readily available and specialist companies have developed, tested and verified their models. The challenge for the process engineer is to know which package to use and to know whether a particular application is the most accurate for the specific process. Metallurgical simulation programs today are well known and proven. Certain programs are specialized while others are broader based. The needs of each user are dependent on the application. Typically, most users require the following operations: • Comminution • Flotation • Hydrometallurgy • Pyrometallurgy • Additional requirements could be defined as: • Thermodynamic capabilities for solids, phases, and gases • Dynamic simulation • Data analysis tools • Coal oriented operations • Diamond oriented operations

Jan 1, 1997

By A. K. Ghose, S. Chakraborti

The research work outlined in this paper examines the utility of index tests for evaluating the strength of coal, both in the laboratory and in-situ. For routine evaluation of strength and deformation properties of coal seams, as inputs for design in stability analysis and equipment selection, the index tests are cost-effective and also make less demand on time and manpower. Four index tests, namely Protodyakonov Index, Cone Indenter Index, the Point Load Strength Index and Schmidt Rebound Hammer, were evaluated for 13 coal samples and correlated to fundamental strength and deformation properties such as uniaxial compressive strength, Brazilian tensile strength and modulus of elasticity of the same coal stratum. The index tests, barring Point Load Index, showed relatively low percentage scatter compared to the fundamental strength and show marked advantages for routine estimation of coal seam strength.

Jan 1, 1986

By M. Gaft, G. Panczer, R. Reisfeld, L. Nagli

Laser-induced luminescence and breakdown spectroscopy methods appear to be a good tool for real-time evaluation of dolomite content on moving belt. The distinctive feature for time- resolved luminescence is Dy3+ emission in apatite, which is excited by 251 nm laser light and detected with delay time of 5 ms and gate width of 1 ms. The distinctive features for breakdown spectroscopy are 604 nm line of F and P in apatite and 518 nm line of Mg in dolomite. The representative sampling of more than 200 pebbles has been studied by both methods. By luminescence method 100% of dolomite will be identified, while approximately 15-20% of apatite with extremely week Dy3+ luminescence may be mistakenly counted as dolomite. By breakdown spectroscopy the identification is 100% correct both for dolomite and for apatite.

Jan 1, 2002

By S. C. Suboleski, R. Zhao

A Simulation/Animation Model (SAM) with several unique features has been developed for continuous mining in room-and-pillar production systems. Initial cut data are generated by the program based on a short list of general section parameters, and is graphically displayed on the screen for checking and editing. This portion of the program includes several intelligent features. For example, a different cut sequence will be generated for uni-directional section ventilation than for bi-directional flow. Once the data are accepted, the entire simulation may be viewed in animation. Effectively, much of the data are checked visually by watching the actions of the mining equipment. Following the simulation, results are summarized as bar and pie charts, as well as printed output. In addition to the extensive use of graphics, the program contains several advances in simulation techniques as well.

Jan 1, 1993

By S. Vijayan

Despite the limited demand for rare-earth elements, as well as yttrium and scandium, in conventional applications, the emergence of ne~ high-technology applications such as supermagnets, lasers and superconductors is expected to result in significant demand for some of these elements. This paper examines the anticipated applications and demands for rare-earth elements over the next decade and their implications on the utilization of available resources. Process methods for the recovery of rare-earth elements from conventional and unconventional resources are reviewed in the context of their growing demand. Challenges facing the industries in meeting this opportunity are also discussed.

Jan 1, 1988

By Lee W. Abramson, James E. Crawley

Caltrans is studying alignments for a 160-kilometer-long high speed ground transportation system from Los Angeles to Bakersfield across the Tehachapi Mountains. This link is needed to connect southern California with San Francisco by a short passenger rail service. None presently exists. The system will require tunnels and viaducts along the route with sections crossing two major active fault zones. High speed ground transportation technologies are being evaluated for achieving rail speeds of between 200 and 480 kilometers per hour. This paper presents the technical requirements for tunnels along the alternative routes being considered for the project.

Jan 1, 1995

By Thomas G. Johnston, Garston H. Blackwell

The development of a block model for a copper molybdenum ore deposit is described. The early use of the inverse distance power estimator, and later transition to geostatistics and kr iging, produced block models suitable for global reserve estimates. Because the global reserve was inadequate for routine mine planning, the production blast hole assays were incorporated into the block model, resulting in excellent local grade prediction. The on site use of small mini, and more powerful personal computers for estimating grades is described. The development of a computer aided, interactive graphic, mine planning system utilizing the grade block model is detailed.

Jan 1, 1987

By D. D. Lei, H. Sevim, S. M. Gwamaka

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated both technically and economically. The objective was to transport, handle and inject the residues into the old workings of the mine at minimum cost. This was accomplished in the following two steps: simulation models were developed and utilized in identifying technically feasible designs for each alternative and the technically feasible designs were economically evaluated to obtain the cost per ton of material transported. An analysis was conducted for varyous distances and tonnages to reveal favorable operating ranges for each alternative.

Jan 1, 1998

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the fol¬lowing corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. • Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, Wv. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its im¬proved accuracy and ease of computerization. • Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1989

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the following corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, WV. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its improved accuracy and ease of computerization. Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1990