Search Documents

Strainburst phenomena, generally characterized by a sudden release of energy in a volume of highly stressed rock, are often encountered in such situations like crown pillar bursts in cut-and-fill mining, face bursts at development headings and floor bursts in deep shaft sinking. This paper describes a simple FE modeling approach which leads to the calculation of the energy release rate (ERR) and the total energy storage rate (TESR) in the rock mass around the openings. The merits of using such energy parameters in the analysis of strainburst problems to identify areas of high energy release/storage are discussed. However, much site-specific back analyses are needed to better understand how strainbursts and energy parameters are inter-related.

Jan 1, 1998

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By William Lyman

GENERAL DESCRIPTION Shrinkage or shrinkage stoping refers to any mining method in which broken ore is temporarily retained in the stope to provide a working platform and/or to offer temporary support to the stope walls during active mining. Since ore "swells" when broken, it is necessary to shrink the muck pile a corresponding amount by draw¬ing some of the broken ore out as the stope is advanced-hence the name. Broken ore retained during stoping is drawn out after the stope has reached its limits. The stope may be left empty or may be filled with waste contemporaneous with, or subsequent to, the final draw. Traditionally the method implies conventional overhand stoping methods with miners working between the muck pile and the stope back, in a space which advances updip with mining and is maintained by balanc¬ing "swell" with "shrink." The shrinkage classification is also applicable to so-called "semishrinkage" methods in open pillar-supported stopes where broken ore is temporarily retained as a working platform but offers no wall support; and to various blasthole shrinkage methods which utilize broken ore temporarily retained in the stope for wall support, but which do not require miners to work from muck pile in the stope. The method is generally applied to steeply dipping veins of strong ore between strong walls. APPLICATION Geometry The geometry of a shrinkable vein is described in terms of dip, width, and regularity along dip. Overall strike and dip dimensions and irregularities along the strike generally impose no restrictions on the method. Dip is ideally 1.2 to 1.5 rad (70 to 90°). As dip falls below 1.2 rad (70°), the shrinkage draw begins to strongly favor the hanging wall side, thus leaving a poor working platform for conventional overhand work. This is particularly true in relatively wide stopes. The sup¬port afforded to the hanging wall also diminishes with decreasing dip, reaching nil as the dip approaches the repose angle of broken ore. Dips below 0.78 to 0.87 rad (45 to 50°) are not generally shrinkable except by open stope "seinishrinkage" methods. Minimum mining width is fixed by working space requirements in the stope-generally about 1 m. Shrink¬age in narrower veins requires that waste rock from one or both walls be broken with the ore and the attendant dilution accepted to achieve the minimum width. Nar¬row stopes are less suitable, encouraging hang-ups and bridging of broken ore, with the attendant problems of erratic draw and incomplete recovery of broken ore. Maximum practical width may be 3 m or less to over 30 m, depending upon the competency of the ore and its ability to stand unsupported across the stope back. This is a vital safety consideration in conventional over¬hand stopes, but is much less of a factor in blasthole shrinkage methods. Very wide veins and massive ore bodies have been mined by transverse vertical shrinkage panels separated by transverse vertical pillars which are either abandoned or recovered later by other methods. Regularity along the dip is a prerequisite of shrink¬age as there must be no serious obstruction to the flow of broken ore downward through the stope to the sill level. Gentle rolls along the dip are acceptable if the local footwall dip everywhere exceeds 0.78 to 0.87 rad (45 to 50°). Off-dip hanging wall and/or footwall splits can generally be mined selectively from a conventional shrink stope as they are encountered without ad¬versely affecting subsequent continuation of shrinkage mining updip on the main vein. Vertical offsets or major rolls along the dip which cannot be "smoothed over" generally require that a sublevel be established with new draw control development. Blasthole shrinkage methods are much less flexible (and thus less selective) in their ability to accommodate any of these irregularities. Ground Conditions The wall rock must be strong enough to stand with the minimal support afforded by the dynamic mass of broken ore in the stope. During active mining, local sloughing from the walls is restrained, but the broken ore affords little, if any, useful resistance to closure of the stope walls. Such squeezing, if present, may bind up the stope and cause the loss of much ore. Pillars left between and/or within stopes are effective in preventing closure but reduce overall recovery. Walls may be re¬inforced by bolting after each stope cut in conventional shrinkage but not in blasthole shrinkage. Ore in place must be strong enough to stand with no natural support across the stope width, although tem¬porary artificial support or reinforcement may be used locally in conventional stopes. Some spalling or sloughing is permissible in blasthole shrinkage as men are never present in the stope. Physical and/or mineralogical characteristics of the broken ore may impose restrictions on stope design and/or operational plan¬ning, and may even preclude the use of shrinkage al¬together. Examples include: ores which, when broken, are cohesive or which tend to pack or cement together under the influence of ground water, wall pressure, and/ or chemical reaction. Such conditions precipitate er¬ratic draw during mining and often result in difficult and/or incomplete final draw; pyritic ores which oxidize very rapidly in the stopes and may generate heat, imposing a fire hazard by spontaneous combustion; sulfide ores which oxidize sufficiently in the stopes to adversely affect mill recovery by flotation; and ores (es¬pecially those containing uranium minerals) which ex¬ude radon gas and thereby impose ventilation constraints on stope design. In most cases these problems can be minimized by limiting the size of stopes, by minimizing the duration of mining activity in each stope, and by promptly drawing each stope empty following comple¬tion of mining.

Jan 1, 1982

By Alejandro Prieto

Traditionally, Mexico has been a mining country. This industry has played a very important role in our country's development, creating jobs, integrating geographical regions - generally very remote from urban communities - and, an essential factor in our present day economy, generating an influx of foreign currency. The Fluorspar mining industry's development started in the 1920?s, but it was not until World War II that its exploitation became consistent and started growing. During the last few years, Mexico has become the world's leading producer, with an annual output of more than one million tons, which directly generates over 3,000 jobs. The actual proven reserves can guarantee fifty years of production at this same annual rate, and it is due to this fact that the producers have not increased their reserves. However, there is concrete information of the existence of several deposits, extending from the northern border to the gulf of Mexico, forming the "Fluorspar Belt? in Mexico.

Jan 1, 1986

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By Sharanappa Yalal, Rakesh Kumar Khali

"Himalayan geology poses the most challenging ground conditions almost anywhere in the world, one of the reasons thereof is their evolution as the youngest mountain chains. They are demonstratively rising faster than any mountain elsewhere. The composition is also younger, and consequently less well consolidated than the other older fold belts. This is consistent with the fact that they constitute one of the most active of the plate margin zones rising at a rate that is almost double the Andes, which is in turn three times that of the Alps. Thus, stress conditions (Magnitude and variations) can potentially be more extreme and adverse on a Himalayan tunneling project. Tunnel excavation under the Himalayan Mountains will pose significantly more challenges than an equal length and equal cover drive almost anywhere in the world. These in-depth-tunneling difficulties through high mountainous terrains have posed major challenges for application of traditional drill and blast (D&B) and NATM methods. Handling such adverse geology at any depth is always problematic and generally leads, if not adequately foreseen, to the significant tunneling delays. The author wants to highlight the challenges faced and on the spot solutions adopted while executing most prestigious 273Km long Udhampur –Srinagar- Baramula Rail Link Project (USBRL) in the Himalayas in the state of Jammu & Kashmir, India. The main focus of the paper is on main stretch of USBRL Project i.e. T-80 (India’s 2nd longest railway tunnel & 3rd longest in Asia) where the team of the author has recently completed a 11.2 Km long tunnel and where the train track has gone operational from Qazigund to Banihal. The construction of this stretch posed several challenges akin to highly adverse geological conditions. Executing on -the -spot solutions, the project has been completed successfully. 1.0 INTRODUCTION Construction of Udhampur-Srinagar-Baramulla Broad gauge railway line is one of the Mega projects undertaken by Indian Railways to establish a dependable transportation in the state of Jammu and Kashmir. In engineering terminology, it is a challenging project negotiating breakthroughs against the complex Himalayan geology. The Project which has been operational over last 12 years , stretch by stretch, is in advance stage of construction . The purpose of the prestigious project is to connect the Kashmir valley to the mainland of the state of the country. On the date owing to the hurdles of the tuff terrain, the transport of this part is totally dependent on the surface transport, i.e., through a road which connects NH-1A from Delhi to Srinagar. The altitude of the region varies from 500.00 to 1700.00, ranging through Udhampur to Katra - Reasi –Sangaldan- Banihal-Quazikund-Ananthnag-Srinagar-and Baramulla. The main features of this project are its Pirpanjal Tunnel and T-48 & 49 tunnels which cover the maximum length of tunneling through thick hostile geological conditions, the total length being 138km. Details of Pirpanjal tunnels are shown in Figure-1."

Jan 1, 2016

By John T. Langstaff

Rock bursts in the deep metal mines of the Coeur d’Alene district present an ever increasing problem in the safe and economic mining of the district’s silver, lead and zinc ores. Hecla Mining Company operates two mines in the district - the Star, a 1100-ton/day lead-zinc mine, and the Lucky Friday, a 750-ton/day silver- lead mine. Rock burst problems at both operations prompted Hecla management to make an all-out attempt to find a practical method of predicting and eventually controlling these bursts. Research by personnel from the Denver Research Center of the Bureau of Mines at ASARCO's Galena Mine indicated that a recognizable pattern of seismic activity preceded some bursts and this activity could be precisely monitored by present- day, off-the-shelf electronic devices. Using information gained by the Bureau and other sources, Hecla designed and installed a 24,- channel seismic monitoring system in the Lucky Friday mine. Installation was completed in December 1973 and after a year of successful operation, it was decided that a similar system would be installed in the Star mine. This second installation was completed in June 1975. Both systems are now operating and providing continuous information on underground seismic activity. Each monitoring system consists of a network of geophones with attendant amplifiers that are connected by shielded cable through an interfacing device to a computer. The origin of each seismic event is determined by the computer and a three-dimensional location is printed out. This information is plotted daily and is used to pinpoint rock burst prone areas and chart their relative seismic activity. This paper will review the causes and effects of rock bursts in the Coeur d'Alene district, the equipment and operation of the microseismic system at the Star and Lucky Friday mines, and the results obtained to date.

Jan 1, 1977

By Sammie D. Guy

This paper discusses the subject of "Improving Contracting Methods" from the owners point of view, particularly the public. An overview is given of the work of the U.S. National Committee on Tunneling Technology and some apparent results of the implementation of these recommendations or lack thereof. Selected recommendations that are not being implemented are discussed as to the the desirability and the possible impact of their implementation. Impediments to acceptance of the recommendations are identified and solutions proposed. The difference in the flexibility, attitudes and approaches of owners, public, quasi-public and private, toward improving contracting methods are discussed. Particular emphasis is given to the fact that the onus to improve is on the owner because they usually develop the contractual language or at least have the final decision on its content and are or should be an equal party to the contract during its administration.

Jan 1, 1983

By D. H. Dvorak

Two pilot-scale biological reactor systems were installed to treat metal-contaminated water. The reactors consisted of barrels and tanks filled with spent mushroom compost, within which bacterial sulfate reduction became established. Concentrations of Fe, Zn, Mn, Ni, and Cd were lowered by over 95% as these metals were precipitated as insoluble sulfides by reaction with bacterially generated H2S. The chemistry of the reactor systems is examined, and opportunities for maximizing their metal-retaining and alkalinity-generating potentials are discussed.

Jan 1, 1991

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

2.1 INTRODUCTION When total extraction of an opening of sufficient size is reached in a horizontal coal seam, the roof strata in the overburden deform continuously to reach a new equilibrium condition. The severity of deformation decreases upward toward the surface. As the downward saggings of the strata propagate and reach the surface, there will be a depression zone on the surface directly above, but extending beyond the edges of the underground opening. This is the surface subsidence basin or surface subsidence trough. The surface subsidence basin is circular in plan view, if the coal seam is horizontal and the mined-out opening is square in shape. But it is rectangular with rounded corners or elliptical if the coal seam is horizontal and the mined-out opening is a long- and thin rectangle or a short-rectangular, respectively (Fig. 2.1). Most underground openings (e.g., longwall panel) assume rectangular shape when total extraction has been completed. Theoretically the edges of the subsidence basin are the points of zero subsidence. But it is difficult to exactly locate the points of zero subsidence. Therefore in practice the points with vertical subsidence of 0.4 in. (10 mm) are used. The final subsidence basin is that which exists long after the mining has been completed, because its magnitude and shape are quite different from the dynamic subsidence basin formed while the face is moving. 2.2 CHARACTERISTICS AND TYPES OF DEFORMATION IN THE FINAL SUBSIDENCE BASIN For a horizontal coal seam, every point in the subsidence basin moves toward the center of the basin. Subsidence is maximum at the center of the basin. Any cross-section that passes through the point of maximum subsidence and either parallel to AB or CD line (Fig. 2.1) is a major cross-section along which principal directions of surface movements occur. However among those infinite numbers of major cross-sections, two specific ones are of special significance, not only because the magnitudes of surface movements are the largest, but also because they are the most easily identifiable directions, i.e., one that is parallel to the faceline at the center of the basin (CD in Fig. 2.1) and' the other is that perpendicular to the faceline but parallel to the diction of face advance (AB in Fig. 2.1). Nearly all the subsidence data obtained in the US have been derived from these two cross-sections, although some cross- sections parallel to CD but near the edges of the panel have also been included. In addition to moving horizontally toward the center of the basin, every point in the basin also subsides vertically. The magnitude of subsidence increases toward the center of the basin. Therefore surface subsidence is a three-dimensional problem and should be treated so in all cases. On all the major cross-sections, only principal subsidence and principal displacement occur. Since subsidence and displacement vary continuously in every major cross-section, three additional deformation components are de- rived, i.e., slope, curvature, and strain. On all other non-major cross-sections on the other hand the five components are accompanied by two additional components, i.e., twisting and shear strain. The seven components of the surface movement are defined as follows (Fig. 2.2): 1. Subsidence, S. On any cross-section, the vertical component of the surface movement vector is called surface subsidence. It generally points downward. But sometimes it points upward in areas ahead of the faceline or beyond the edges of the opening. In such cases it is a surface heave which is usually less than 6 in. 2. Displacement, U. On any cross-section, the horizontal component of the surface movement vector is called surface horizontal displacement. It generally points toward the center of the subsidence basin. But in steep terrain, it moves along the downdip direction 3. Slope, i. On any cross-section, the difference in surface subsidence between the two end points of a line section divided by the horizontal distance between the two points is called the surface slope of the section. 4. Curvature, K. On any cross-section, the difference in surface slope between two adjacent line sections divided by the average length of the two line sections is called the surface curvature of those two line sections. There are two types of curvature: con- vex or positive curvature and concave or negative curvature. 5. Horizontal strain, e. On any cross-section, the difference in horizontal displacement between any two points divided by the distance between the two points is called horizontal strain. If the distance between the two points is lengthening, it is tensile strain with positive sign. Conversely, if it is shortening, it is compressive strain with negative sign 6. Twisting, T. On the surface of the subsidence basin, the difference in slope between two parallel line sections divided by the distance between the two line sections is called twisting. 7. Shear strain, y. Shear strain is the changes in internal angles of a square on the surface of the subsidence basin or on any major cross-section. It is the summation of the differences in incremental (or decremental) lengths between the two opposite sides divided by the original distance between the two opposite sides. More precisely, the surface deformation indices (i.e., slope, strain, curvature, twisting and shear) are defined by derivatives of surface movement components. For simplicity, the x- and y-axes of the cartesian coordinate system are set to be parallel and perpendicular to the cross-section of interest, respectively. In such a coordinate system, slope and curvature along x direction are the first and the second derivatives of the vertical components (S) of surface movement with respect to x, respectively, or i, = ds/dx and kx = d2s/dx2. Horizontal strain along x direction is the first derivative of the component along x direction of the horizontal displacement,

Jan 1, 1992

By S. A. Lolon, J. F. Brune

"INTRODUCTION In underground longwall coal mining, the mined-out areas or gobs frequently contain methane which can form explosive methane-air mixtures. Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of such explosive mixtures, herein referred to as Explosive Gas Zones (EGZs), inside and around the perimeter of bleeder-ventilated longwall gobs (Loane et al., 1975; Lynn et al., 1986; Elkins, et al., 2001; McKinney et al., 2001; Dziurzynski and Wasilewski, 2012; Brune, 2013). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Several factors can induce EGZs outflowing from the gob, but the most common cause is the fluctuating barometric pressure. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Other sudden pressure changes can result from roof falls, failing ventilation controls and fan outages. Any such fluctuation of mine ventilation pressure will disturb the pressure differential between the gob and the surrounding mine workings and may cause EGZs to outgas from the gob. The correlation between major mine explosions and abrupt barometric pressure changes has been studied and confirmed for explosions in coal mining countries including the United States, South Africa, Australia, and Poland (Hosler, 1948; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Hemp, 1994; Wasilewski, 2014; Belle, 2014; and Lolon, 2017). Disastrous mine explosions appear to happen more frequently during stormy weather, which, in the United States, typically occurs during the late fall and winter seasons. ROOT CAUSE AND EFFECT OF GOB BREATHING Gob breathing is the result of the pressure differential between gob internal and external pressures caused by external atmospheric pressure fluctuations that occur naturally as a result of gravitational and thermal forces in the atmosphere (Lindzen and Chapman, 1969). Other major and sudden pressure changes may be caused by fan failures, failures of ventilation controls or roof falls can also cause an unexpected gob breathing. Normal barometric fluctuations occur every day but usually do not pose an explosion risk as they occur gradually so gob pressures have sufficient time to equilibrate. More extreme fluctuations associated with cyclonic weather systems and storms often result in more rapid and larger drops or rises in barometric pressure (Hosler, 1948; Fauconnier, 1992). A study by Lolon (2017) found that the timing of historical mine explosions showed consistency with the occurrence of abrupt and intense barometric variations."

Jan 1, 2018

By Peter L. Siems

Humid tropical environments pose many problems for mineral exploration. The problems result from thick lateritic soils, dense vegetation, seasonally heavy rains, deep chemical weathering, few outcrops and thick saprolites. Although geochemical exploration should be potentially a useful technique in these environments, it appears from the scarcity of reports in the literature that insufficient attention has been paid to developing procedures that are specific to the needs of humid tropical areas. For this reason, the authors believe that this account of a geochemical study in a tropical coastal area on the edge of the Brazilian shield is of general interest and importance for potential geochemical exploration surveys in similar areas within the tropics. The objective of the geochemical study was to develop a practical technique of reconnaissance geochemical prospecting for copper deposits in Brazilian tropical coastal lowland areas. In order to achieve this objective, information concerning the secondary dispersion of copper in these areas was required. Consequently, an orientation survey was designed to provide this information. The present account contains details of the geochemical study and the information about the secondary dispersion of copper that was acquired during the course of the orientation survey. Location and Climate The field area is on the Atlantic coastal lowland of Brazil at latitude 13°S. It lies approximately 10 kilometers south of Maragojipe, a city of 15,000 inhabitants; this city is on the western side of the Bay de Todos os Santos about 45 airline kilo¬meters northwest of Salvador. (See Fig. 1) A good gravel road from Sao Felipe to Sao Roque do Paraguay crosses the southern part of the field area. The climate of the area is hot and moist, and is without prolonged dry periods. The mean annual rainfall is about 1600 mm (63 in.) and the greatest precipitation occurs during the winter months of May and June and the summer months of December

Jan 1, 1972

By Robert A. Westman

The INRED process has been developed step by step by Boliden since 1972 at MEFOS, the Foundation for Metallurgical Research, at Lulea in Sweden. The demonstration - plant is number five in this series. The purpose of this plant, which has a nominal capacity of 60,000 tonnes per year of hot metal is to: 1) prove the process on a sufficiently large scale to provide the basis for construction of production plants, 2) test various kinds of raw materials on behalf of licensees, 3) train operators of the first production plant, 4) develop the process further for special applications.

Jan 1, 1983

By B. K. Baird

The application of cutoffs during and after pit optimization is examined for a lower-grade multi-metallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block, incorporating parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which of these parameters have a significant effect on the total contained resource tonnage and total contained non-discounted revenue in the optimized pit. The cumulative effect of changing several of the more significant parameters is investigated. Application of a copper cutoff grade to a block inside the optimized pit could result in the less than optimal extraction of the resource. A block with copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher copper grade block may be sub-economic. The relative merits of applying a copper grade cutoff, "equivalent grade" cutoff and dollar value per ton cutoff to blocks inside the optimum pit are discussed.

Jan 1, 1999

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

By R. A. Hill

A brief explanation of the theoretical functioning of a regenerative system followed by its application to firstly, shuttlecars and then continuous miners and its effect on performance thereof with regard to handling, production and safety.

Jan 1, 1986