Search Documents

By W. F. McDermott

One of the major improvements in ore grinding economics in North America has been the introduction of autogenous grinding. The history of this has been well documented in previous AIME presentations and in the literature. Pickands Mather & Co. has been very active in the development of autogenous grinding since 1957. This early work led to the application of autogenous grinding to the Wabush Mines ore in 1965, with the installation of 6-24 ft. diameter by 8 ft. long - 1,750 HP mills. Development work recently completed in 1971 on another ore has led to the decision to install 5-36 ft. diameter by 15 ft. long - 12,000 HP mills when this project goes ahead. Between these two decisions lies a tremendous amount of research, development, and application of autogenous grinding to a variety of ores. The Pickands Mather Metallurgical and Research Laboratory in Hibbing, Minnesota has tested, in its pilot plant facility, ores from 9 different deposits. Some of these deposits have as much difference within their own ore types as there is between the various deposits. Therefore, it is safe to say that over 20 different ore types have been tested and flowsheets developed for commercial applications. Of the 9 projects, 3 are in operation. These are Wabush Mines in Labrador, Canada, (1) Savage River Mines in Tasmania, (2) and The Griffith Mine in Red Lake, Ontario, Canada. (3) Pilot plant work has encompassed over 300 individual tests. These tests were carried out in mills that were 5-1/2, 8, and 12 ft. in diameter. Grinding power requirements for the primary autogenous milling has varied from 2 to 30 KWH/Lt of crude ore.

Jan 1, 1972

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By Harley G. Pyles

Rotary Percussion drilling has shown great improvement over rotary drilling, when hard roof is encountered. In addition, Rotary Percussion drills have eliminated the need for air drills in many applications. Improved drilling rates have been achieved but roof bolting is still a bottleneck in many operations and the demand for further improvement will continue. Drilling rates beyond current performance is limited by the capabilities of existing drill steels and bits to resist increased horsepower input. The most apparent immediate solution to improved drilling is to increase the strength and rigidity of the drill steels. Drilling experience indicates that a l-1/2" diameter or 1-5/8" diameter hole can be drilled as rapidly or 'more rapidly than the standard 1-3/8" diameter hole. Greater torque and thrust capacities can be achieved through the use of larger O. D. and I. D, steels, however, this is only possible if the larger hole sizes can be made allowable. Large diameter anchorage shells can be made available at a slight extra cost.

Jan 1, 1965

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

The surface of chalcopyrite was studied in situ in aqueous solution by an atomic force microscopy (AFM). The AFM images showed that some absorbate in patches was detected on the mineral surface, after the chalcopyrite sample was soaked in 5x10-4M potassium ethyl xanthate (KEX) solution at pH 11 for 10 minutes. These patches increased in size with time elapsing. At the same time, as shown by the obtained AFM force curves, the adhesion between the AFM tip and the substrate increased greatly due to the adsorption. Rinsing with ethanol removed the absorbate from the chalcopyrite surface, as well as the big adhesion observed in KEX solution.

Jan 1, 2010

By J. M. Melluish

The metallurgical response of the Point Leamington deposit has been studied. Two series of bench tests were conducted and various ore samples and flotation products were examined using image analysis techniques. The majority of sphalerite and chalcopyrite grains in this texturally complex ore were found to be smaller than 10 micrometers. Copper recoveries were low with losses mainly as fine inclusions in pyrite. Sphalerite recoveries were somewhat better due to a generally coarser habit. Gold and silver recoveries were also low and only solid solution silver was identified in the ore. The deposit shows poor economic prospects unless additional tonnage of high grade zinc ore can be delineated.

Jan 1, 1989

By John E. Auten

The computer program "Spike" is an "expert-rule based system" designed to fulfill two requirements. 1) acquaint unfamiliar personnel with big hole drilling techniques and 2) to stimulate the "old hands" in solving drilling problems. "Spike" will not make anyone a drilling expert The best way to understand a computer program is by example, but first some explanation of an? "expert-rule based system", As the name implies, the program tries to imitate a human expert. Unlike a normal computer program which uses a list of instructions to follow in a set order, a rule-base program has a collection of independent rules without an explicit list of things to do, one after the other. This type of program was mandatory to accommodate the ever changing situations and corrective actions that more accurately duplicate actual drilling operations and the advise of an experienced drilling expert.

Jan 1, 1988

By Z. Kokesz

The following paper presents the results of geostatistical studies of the selected hard-coal deposits in Poland. Geostatistical methods were applied mainly to the characterization of variability structure of the coal seams thicknesses as well as sulphur and ash contents in the coals. Results imply that the accuracy of coal reserves estimations can be improved if kriging method is applied. Kriging allows predicting more precisely the values of such parameters as thickness and sulphuring content.

Jan 1, 1993

By Y. S. Roditis

Traditionally, open pit optimization has been used to produce a single outline which can guide the pit design. This paper describes how a series of optimum nested pits are utilized to: a. produce different mining sequences and to help in mine planning and phase design; b. evaluate different metallurgical processes, production scenarios and equipment size; c. investigate the sensitivity of a project to prices, recoveries, production rates, costs, ultimate pit slopes etc.

Jan 1, 1993

By Henry N. McCarl

[ ]

Jan 1, 1966

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the U.S. for the detection of fire in the belt entry and monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data has the potential to provide fire characteristic information such as fire growth (heat release rate) and exact fire location. This information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation, and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide (CO), carbon dioxide (CO2), and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division (PMRD) Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. INTRODUCTION Fires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases. The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke, and toxic gases are produced and transported by the ventilation system, and provides an indication of the time available for escape or firefighting [1]. The HRR is also an important input parameter to mine fire simulation models. Measuring the HRR of an actual fire can be a difficult task. Early experimental measurement of HRR focused on the heat output as represented by the temperature of the product gases. In ASTM E1321 (LIFT test), an array of thermocouples was positioned in a duct which captured all gaseous combustion products to measure their average temperature. This approach assumed the flow is adiabatic, which is never a reality. Significant progress on measuring HRR was made when Huggett showed that, for most common materials containing C, H, O, and N, the average heat release per unit mass of oxygen is 13.1 MJ/kg O2 [2]. Thus, the oxygen deficit is a measure of the HRR in the flow that the duct captures. This approach is termed oxygen consumption calorimetry (or the oxygen consumption method), and is widely used in the fire protection community."

Jan 1, 2017

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

The Mesabi Range extends continuously from near Grand Rapids, on the Mississippi River, E.N.E. for a distance of about 1120 miles to near Birch Lake, where it is covered by the large gabbro flow which forms the base of the Keweenawan series. The same formation (Mesabi) appears again near Gunflint Lake on the international boundary, and shows as far east as Thunder Bay on the north shore of Lake Superior. Between Mesabi station, on the Duluth and Iron Range Railway, and Birch Lake, although considerable exploration work has been done, there is no evidence of concentration of ore in workable bodies. The Gunflint beds are thin alternating layers of chert and hematite. Alt the workable deposits at present known, on the Mesabi, lie between Mesabi station and Grand Rapids, the greater number being St. Louis County simplified geologic column is given herewith instead of the complete correlation table given by the United States Geological survey.

Jan 1, 1920

By R. R. Fernández

The Newmont roasting plant in Carlin, Nevada, commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable affecting the structural characteristics of the calcine, which in turn affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature has been closely monitored since October 2000. The original design temperature was 550° C. Lower roaster temperatures of around 500° C resulted in a gold recovery increase of more than six percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an ?intelligent? process control system helped significantly in achieving steady low roasting temperatures, thus obtaining high gold recoveries of 92 to 93 percent. Under these conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease in gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g., porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2010

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By H. W. Seany

Over the years since the initial experiments with underground concreting were made in 1956, attesting to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the, mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other advantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 1, 1965

By Daniel Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abundant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleistocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional resources. Limestone uses include cement and lime manufacturing, concrete sand and aggregate, mad base material, beach sand replenishment, agricultural lime and golf course construction.

Jan 1, 1982

Eldorado Resources Ltd.(ERL) uses a solvent extraction process for the processing of uranium ores. The solvent extraction plant consists of 4 extraction and 5 stripping stages with regeneration carried out as required (Wyper, 1982). Extraction is carried out with a solvent consisting of 4.5 vol % Alamine 336, 4.5 vol % Isodecanol and 91 vol % kerosene. The extraction step can be represented as In equation (1).

Jan 1, 1988

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By Brad Grothen, Lok Home

The choice of TBM type is never easy, but it becomes especially challenging when faced with a hard rock tunnel with expected high water flows and pressure. Slurry Shield tunneling has a long history of being used in these conditions to minimize the risk, though this method has brought with it other risks along with cost considerations. At recent projects around the world, another method has been proven to effectively manage these project risks without utilizing Slurry Shield tunneling: Shielded, NonContinuous Pressurized (NCP)-TBM tunneling in rock with a comprehensive grouting program. In this paper, the authors will analyze the use of Shielded NCP TBMs at projects around the world as compared with slurry shield tunneling in rock under water pressure. Recommendations will be given in order to establish a clear picture of the optimal tunneling method.

Jun 13, 2021

By Peter T. Luckie

Up until the past couple of years, thermal coal dryers were only used to dry midwest and eastern United States bituminous coals. These dryers were primarily installed at coal preparation plants to freeze proof the coal and lower the transportation costs per BTU. Today thermal coal dryers are being specified to dry western sub-bituminous and lignite coals for these and other reasons brought about by the intense interest in coal gasification and liquefaction. One reason for drying western coals ahead of a coal gasification plant is the elimination of surface moisture which would prevent efficient sizing of the coal, since feed material size consist is very important in most commercial coal gasification processes. Thermal dryers are being proposed for liquefaction processes because of the need for a feed material containing approximately 4% or less total moisture Future coal gasification processes may also need to reduce feed material moisture content.

Jan 1, 1975