Search Documents

By Thomas F. Torries

It does not take sophisticated economic analysis to determine the current status of nickel production and demand (Figure 1). One only needs a quick glance at the balance sheets of the major nickel producers to learn that prices are down and profits are supressed to the point where they are major losses. Operations have been closed, and those remaining in production have reduced output. What Is now of interest Is, when will the nickel market improve and to what degree? The purpose of this paper is to attempt to answer these questions. This will be done by the normal method of projecting nickel demand, chosing a production scenario, and analyzing the results.

Jan 1, 1982

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By T. J. Fronapfel

Impacts to ground water from mining are being comprehensively regulated in Nevada through specific requirements for design, construction, operation, permitting and closure. This program is the nation's most comprehensive for control of activities at mining operations which have the potential to cause groundwater degradation. It encompasses virtually all types of facilities, including placer, physical separation, flotation, testing, leaching and milling. Minimum design requirements are established by regulation, and must be met by each facility. Site-specific monitoring requirements are established for each facility, and are heavily emphasized. Regulatory and technical requirements and relevant permit conditions are presented and discussed.

Jan 1, 1992

By Jurgen Hahn

The paper reports on both, the design and decision making for the filters in a backfill plant in Europe as well as more then 10 years of operation and maintenance experience of the vacuum disc filters installed. It begins with the first step, the filter sizing based on a sample provided by the customer, followed by the commissioning of the filter units and reports on the development of the filter performance during the following 10 years of operation. Based on the physical properties of the sample and the process targets of the client for the backfill plant, the paper shows the logic steps taken in the laboratory to ensure the target moisture, determine the required filtration area and filter size as well as the selection of the ancillary units and the formulation of the performance guarantee. The paper discusses some issues with filter operation during the commissioning phase and the actions taken. Finally, the paper concludes by highlighting the gradual change over the more than 10 years of operation and how this change affected filter performance and operating costs.

Feb 1, 2024

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and surficial evaporite brine. Those advantageously located now supply world markets. Materials of similar grades and magnitude, but less favorably located, will come into production as present sources are depleted and markets expand. Some of these potential supplies have been explored, and are reserves in the sense of known availability and quality. Reserves herein are of two classes, those proved by close drilling and assaying, and those of only probable status because their scale and grade are unsystematically indicated. Possible resources include similar materials whose bulk can only be inferred on indirect evidence. All figures apply to total materials in the ground. No allowance is made for losses in mining, evaporation, beneficiation, or chemical processing.

Jan 1, 1977

By R. C. Timberlake

In the past three years there has been a great amount of attention given to phosphates world wide, and in particular to the Florida Phosphate Industry. I would like to relate some of the most recent history of the industry and give you a personal outlook for the future. Phosphate rock has been produced in Florida since its discovery on the Peace River in the 1880's. Through 1976, approximately 720 million ST of rock had been mined from Florida reserves, and it is my opinion that there are at least 1.2 billion tons remaining which are consolidated, accessible and can reasonably be expected to be permitted for mining. Over half the 1.2 billion tons will be deeper, more scattered, leaner and will produce lower grade rock than the Bone Valley of Central Florida has tradition-ally produced. In 1973, '74, '75 and '76 the Florida Phosphate Industry produced 32.6, 34.0, 38.2 and (38.0) (P) million ST of phosphate rock respectively. This rock was produced by ten mining companies, Agrico, Borden, Brewster Phosphates, Gardinier, Grace, IMC, Mobil, Occidental, Swift, and USS Agri-Chem; mines are located -17 in Polk County, one in Hillsborough County and two in Hamilton County, Florida. Phosphate rock is used by local companies in Florida primarily to produce phosphoric acid from which DAP and TSP is manufactured. Florida acid producers use about 15 million STPY in acid plants in Florida, and another 7.5 million STPY is consumed by acid producers in plants on and near the Mississippi River. Somewhat

Jan 1, 1977

By Y. K. Yen

The most serious problem for on-line coarse particle size measurement from a conveyor belt by image analysis is the overlap phenomenon that occurs between adjacent particles. A methodology is developed and described in this paper to estimate the sieve size distribution from the overlapped projected particle images as might be obtained from a conveyor belt. Two aspects of the overlap problem have been taken into consideration. First, several image processing algorithms were studied to find the most suitable technique to separate the projected overlapped particle images for narrow sized particles. These image segmentation algorithms include two-dimensional thresholding, edge detection and Watershed discrimination techniques. The other aspect of the overlap problem is related to the determination of the general kernel function for the partial particle images obtained from the projection of the overlapped particle bed. In this regard, a computer simulation technique was applied to mimic the overlapped particle bed for narrow sized particles, then the general kernel functions of the partial particle images were determined.

Jan 1, 1994

By D. Erik Spiller

Mineral processing technologies are being used in the environmental arena for remediation and secondary recovery. Comminution and/or scrubbing for liberation, coupled with separation of the liberated particles, is known as soil washing. Other metallurgical unit operations have found application in remediation and recycling: size classification, gravity concentration, flotation, magnetic and electrostatic separation, eddy current separation, and liquid/solid separation. This paper presents specific examples of the use of these technologies to clean up contaminated soils and plant residues, and to recycle valuable materials from waste streams.

Jan 1, 1993

By Larry F. Barrett

Anaconda exploration in the Rico mining, district from 1978 through early 1983 resulted in discovery and partial definition of the Silver Creek molybdenum deposit. Approximately 44 million tons of 0.31% Mo are drill-indicated, and projections suggest that the deposit exceeds 200 million tons. No source intrusion has been intersected by drilling, but its composition is suggested by silicic alkali-alaskite porphyry dikes of intramineral age observed at the surface and in drill holes. Age data and fluid inclusion studies indicate that the deposit was formed 5.2 ±2 m.y. ago and that more than 1,200 meters of cover has since been removed by erosion. Both emplacement of the hypothesized source intrusion, and the geometry of the molybdenum deposit, were influenced by three major intersecting faults. The most significant of these, the Last Chance fault, juxtaposes Precambrian quartzite and greenstone against Pennsylvanian clastic and calcareous sediments within the mineralized zone. Wallrock alteration associated with the deposit is characterized by potassic, phyllic, and propylitic zones in non-calcareous rocks, and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Pre-mineral faults that intersect the deposit contain the only surficial molybdenum, tungsten, and fluorine anomalies. Pervasive dispersion haloes of the indicator elements were intersected at depth by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1985

By B. Kraus

Many of us who have interacted with senior executives from leading oil and gas companies over the last few years on the subject of HSE performance have observed a marked shift in their engagement on this aspect of their business performance. There seems to be a shared impression that HSE performance will have markedly increased impact on their businesses going forward. On the back of this very real concern, many are taking material actions to secure a step change in their safety and environmental performance: hiring respected mainstream operational personnel to lead their HSE function; investing in capacity/skills development for HSE professionals to increase their effectiveness in addressing the needs of the business; taking a hard look at the efficacy of established management and audit programs (too much paper, not enough results?); investing in information management systems so they can have access to real time reliable performance indicators; and, critically, initiatives to reduce accident statistics (especially focused on fatalities and contractors? activities) and deliver meaningful reductions in their environmental footprints. Underpinning all of these actions is a clear sense that substantial, very well-intentioned activity and investment in HSE aspects of the business has not been hitting the mark and yielding too little return in terms of performance improvement. The very serious recent events on the US Gulf Coast and at a refinery in the US Pacific Northwest have added fuel to this fire. The need for approaches which will secure a step-change in performance on the front line in the global oil and gas industry has never been greater.

Jan 1, 2011

By William Gleason

"On April 4, 2017, the largest earth-pressure-balance tunnel boring machine (TBM) ever built finally completed its 2.7-km (1.7-mile) journey beneath Seattle, WA, nearly four years after it began boring the SR-99 tunnel that will eventually replace Seattle’s Alaskan Way Viaduct.By now, readers of this publication are familiar with the ordeal that began on Dec. 6, 2016, when the machine overheated and shut down. Until that point, the TBM, named Bertha, had grabbed headlines for being the largest in the world with a 17-m (57.6-ft) diameter face. But after the incident that stopped the progress, the headlines suddenly stopped focusing on the engineering marvel of the tunnel project and began asking what went wrong. Just 300 m (1,000 ft) into the tunneling journey the machine was stuck, unable to move forward and impossible to retract.The project’s contractors, Seattle Tunnel Partners,(STP JV) – a design-build consortium comprised of Dragados - USA, Tutor Perini, say a 20-cm (8-in.) steel well-casing buried in the path of the machine caused the problems that halted the TBM. The Washington State Department of Transportation (WSDOT) disagrees, and the issue over who ultimately pays for the repairs is now with the courts.Eventually, engineers determined the best way to get Bertha back to work was to dig a 36-m (120-ft), deep concrete lined shaft pit in front of the machine and lift the 1.8-kt (2,000-st) cutterhead out for repairs. The repairs took two years but eventually the machine resumed mining in January 2016. In April 2017, the TBM finished building the tunnel, breaking through at the tunnel’s north end near Seattle’s Space Needle, with little to no ground surface movement measured on the entire alignment.While the cause of the TBM breakdown and who should pay for repairs was debated above ground, the work below ground continued. David Sowers, deputy program administrator, engineering and program management with WSDOT, told Mining Engineering during the 2017 Cutting Edge Conference in Seattle that in addition to the technical marvel that the tunnel became, the fact the parties involved were able to work through the unprecedented challenge is a great example of how to overcome challenges on massive projects."

Jan 12, 2017

By G. L. Merritt

The implementation of the Surface Mining Control and Reclamation Act of 1977 (SMCRA) has evolved into one of the most complex environmental protection programs to come out of the late 1970's. The level of detail in the statute and the regulations have resulted in a rigid and complex set of requirements for the administration, permit-ting, inspection and enforcement of the program. In addition, the constant change of the federal program caused by regulatory changes, reorganization of the Office of Sur-face Mining Reclamation and Enforcement (OSMRE), ongoing litigation involving OSMRE, and the use of the budget to establish additional mandates on OSMRE and the State Regulatory Authorities have resulted in an unstable program. The instability of the program makes it extremely difficult for the States to implement their programs and to achieve the goals of SMCRA.

Jan 1, 1988

By R. Buchan

A number of mineral processing techniques have been adopted for the separation of the plastics making up a typical beverage bottle, and a complete flowsheet developed. Thus, size reduction, heavy media separation and flotation were used to separate PE, PVC and PET from their mixtures with cellulose fibers and aluminum, which makes up the cap of such bottles. It is shown that while heavy media separation allows the separation of a PVC/PET mixture from the solid waste, froth flotation can be readily used to separate PVC and PET from a mixture of the two. For this purpose, the differential action of an alkaline aqueous solution (PH=II) which contains methanol and MIBC as surface tension control agents has been found to be a suitable flotation medium. This paper reports some aspects of the flotation flowsheet developed for the separation of plastics from municipal solid waste mixtures and PVC from PET.

Jan 1, 1995

By Stephen Semeniuk

Discussion by Stephen Semeniuk Discussion As a valuator and SME member, I view Ross D. Lawrence's position as based on unproven and faulty assumptions made with regard to the pragmatic evidence presented in his paper. Moreover, his call for the inclusion of all mineral resources in discounted cash flow valuations is redundant, if not irrelevant, as there are procedures that already take all classes of mineralization into consideration for valuation purposes. In my experience as a valuator, I find that Canadian securities regulators are more than accommodating in allowing any valuations of mineral properties to be based on cash flow calculations. In other business areas, the same regulators usually reject discounted cash flow valuations of projects or businesses with no operating history. Instead, the regulators prefer valuations to be based on other transactions tested in the marketplace. Valuations based on actual market transactions are less subjective than discounted cash flow calculations and/or the capitalization of arbitrary, untested or undemonstrated earnings projections. In the mining and minerals sector, such projections may be made by persons not qualified to make such projections. In support of this statement, I direct readers to the article "Valuation of mineral properties which do not contain exploitable reserves" by Lionel C. Kilburn, which appeared in the August 1990 issue of the CIM Bulletin. To quote from the article: "Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand, and political-economic conditions, all of which vary with time. Five fields of expertise influence the value of a mineral property: •geological engineering, •commodity markets, •financial markets, •stock markets and •mineral property markets. The skills of geologists and engineers properly apply to the first field of expertise. Knowledge and consideration of the other four fields is important, but such advice is more properly sought from marketing experts, economists and stockbrokers." Securities regulators have created no hardship for valuators by excluding unsubstantiated resources in discounted cash flow valuations. In the field of engineering, best design practices apply. A margin of safety is built into the design criteria for any new equipment or structure that will exceed normally expected load levels and stresses, even though such considerations imply higher front end costs. In accounting, the comparable operating principle is conservatism. It explains why, for balancesheet presentation purposes, inventory is stated at cost or market, whichever is the lowest value. Similarly, when the engineering or geoscience-based valuator plays in the field of finance, the rules of accounting and applied economics apply. Regulators in their skepticism of income-based valuations are in tune with similar views already expressed in mining literature. To quote H. Van Tingley, in Mining Magazine, July 1996: "... the DCF method has inherent dangers when applied to undeveloped resources. Firstly, it presents an often-undeserved aura of accuracy. A DCF value is no more accurate than the least accurate of the assumptions incorporated into the calculation - and assumptions

Jan 1, 2003

By G. J. Hartman

The Fort Cady in situ borate mining project involves recovery of boron from a mineral deposit located over 1400 feet below the surface. The resource recovery method is being developed using in situ mining technology employing weak acid solution injected directly into the ore body. As the acid contacts the calcium based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by use of submersible pumps. At the surface the borate values are recovered as a finely divided solid white powder after a series of chemical reactions and precipitations resulting in the production of calcium borate. The refined product is then sold under the trade name CADYCAL 100.TM All environmental permits for up to a production rate of 90,000 tons per year have been obtained. These permits required an Environmental Impact study (EIS) for federal lands and an Environmental Impact Report (EIR) for the private portion of the property. Regulatory permitting required over 5 years to obtain all the various authorizations for this project. The ore body has an average thickness of 118 feet extending over 273 acres. At a production rate of 90,000 tons per year with only a 70 percent resource recovery allowance, in place reserves are sufficient to sustain production for over one hundred years.

Jan 1, 1997

By Edward K. E. ] [Williams

Conditioning is any treatment of an ore with or without reagents which affect its floatability. While it can start in crushing or grinding circuits and continue into the flotation circuit, conditioning will refer here only to reagent treatment in an agitated tank designed for the purpose. Such treatment is often unnecessary with sulphide ores and collectors or with amines,* but it has long been recognized as essential with fatty acid collectors in the flotation of non-sulphide minerals, The requirements can be extremely variable, depending upon ore alteration, the presence or absence of slimes, and 1 the minerals to be separated. The study described here was concerned with the recovery of oxidized molybdenum minerals from an ore containing the element in both sulphide and oxidized form. Flotation of the iron minerals with which the oxidized molybdenum was associated was the basis for the process. Recovery and optimum concentrate grade without desliming depended upon a twenty to thirty minute conditioning of the pulp with flotation reagents at forty to fifty percent solids and at high turbulence. The objective in the study was the determination of design and operating criteria for conditioners in order to permit scaling-up of the results without repeating the entire study on a larger scale.

Jan 1, 1968

By W. E. Lytle

Environmental permitting is a critical component for joint-venture projects located in the Commonwealth of Independent States (CIS). This paper presents the basic CIS regulatory environmental requirements for permitting of a hypothetical mining source and emphasizes air permitting. Topics which will be covered include: the Expertiza process, air pollution quantification, data requirements, and air pollution modeling protocol. A comparison will be made between permitting requirements for air pollution sources in the United States and a CIS country, Kazakstan.

Jan 1, 1998

By Yadong Xue, Fei Wang, Hongwei Huang, Yan Sun

"Increasing attention to subway tunnel maintenance is being paid with the high speed development of urban rail transit system in China. A novel moving tunnel inspection equipment based on machine vision is developed in this paper. High resolution image acquisition system is proposed for tunnel crack and leakage inspection. The main components of this image acquisition system includes high speed CCD cameras, linear lights and high performance computer. To inspect the crack less than 0.3mm with a 3-5km/h speed in subway tunnel, we need to consider resolution and line rate of camera, pixels of cameras, range of inspection and illumination intensity of lights simultaneously. The optimization design is proposed to make the equipment more convenient for tunnel use. Entire tunnel situation can be detected and recorded in a single inspection process. This equipment has already been verified in Shanghai subway tunnel for defects inspection.1. INTRODUCTION In China, the quantity of subway tunnel has reached a large scale in recent years. Until 2014, there had been more than 2300km of subway tunnel in China which accounted for nearly three quarters of Chinese urban railway system (Zhang Chen,2015). In some metropolises like Beijing and Shanghai, most of the metro tunnels has already run over 20 years which within maintenance phase. This has brought about plenty of inspection work and maintenance work to guarantee the tunnel under the serviceability limit states. The increase of running mileage of subway tunnels in China has been displayed in Fig 1."

Jan 1, 2016

By B. Schimm

Mining of material without blasting and / or selectively becomes more and more important for high quality ROM-products. Surface Miners have been developed especially for this purpose. The cutting technology of these machines has been improved, so that harder material as well as wet and sticky materials can be cut with better results now. Especially the cutting drum design and more precise drum manufacturing process now allow production and equal tool wear over a long period. The better knowledge of rock parameters influencing the cuttability and cutting results allow higher production, less cutting tool wear and therefore reduced production costs.

Jan 1, 1999

By Karel Rössler, Petr Vítek

"The Ejpovice tunnels in Czech Republic were built by EPBM in soft Clyashale, and in weathered profile with low soil overburden. The segmented liner at the cross-passage openings required support, which would not interfere with the EPBM clearance envelope during the scheduled pull back of the EPBM through both tunnel tubes. For that reason support frames or radial bolting could not be used. Steel rods inserted into the neighboring segments during the ring assembly, and later grouted were tested and realized as an innovative solution. The paper presents practical experience gained with the segmented liner support during cross-passages construction. INTRODUCTION An innovative solution using the grouted dowels was developed and realized for sixteen cross-passage openings of the twin Ejpovice Tunnels, whose construction was part of the railway track Rokycany – Plzen modernization. The following paper described practical experience gained with the innovative support of cross-passage openings, which was realized by short steel dowels grouted within the segments of the EPBM segmented liner. The paper is a continuation of the paper published in WTC 2015, which described the design aspects of the grouted dowels support, while the following paper concentrated on the production, and the performance of the dowel support observed during the breakout for the cross-passages openings. The connection by grouted dowels was patented by Metrostav, a.s. Company THE EJPOVICE TUNNELS CONSTRUCTION The Ejpovice tunnels construction started in 2013. The start of the high speed train operation through the tunnels was planned for 2018. The project was funded by the state government with the support of European Union funds of up to 70%.The tunnels were excavated with one EPBM (Earth Pressure Balanced Machine) with the external diameter of 9.89 m. The segmental liner inner diameter was 8.7 m, and thickness of 0.4 m. First, the South tunnel tube was excavated from the East portal, then the EPBM was pulled back through the South tunnel, and the excavation was started from the same portal for the North tube. After the South tube was freed from the EPBM excavation operations the cross-passage construction started. Due to the short time schedule, in the North tube the cross-passage construction started while the tunnel was still under construction. Therefore, the cross-passage construction was performed concurrently with the segments transportation, and with the EPBM pull-back through the tunnel. There were 8 cross-passages along the tunnels with a maximum distance of about 500 m, Fig.1."

Jan 1, 2016