Search Documents

By Lynn E. Bowman

Efficient filtration of fine kaolin particles plays a crucial role in the processing of raw kaolin to a marketable product. Filtration can often be the rate-controlling step of the whole process. Consequently, plant production depends on the rates being achieved in filtration. To alleviate the bottleneck in production, Nalco Chemical Co. initiated a reagent development program to chemically enhance the performance of the filtration units. Filter aids of different classes were assembled and evaluated in bench simulations. These included reagents whose primary mode of functionality were coagulation, flocculation, thickening and combinations of each. This article discusses the development and application of a new reagent that improves the filter production rate with minimal impact on filter cake percent solids. Plant data indicate that this reagent can increase production rates by as much as 35% on clays of varying particle size, as well as clays that are calcined. The reagent's impact on solids content, re-slurrying characteristics, Brookfield and Hercules viscosity and drying is within the standards set by plants that evaluated and now use this product.

Jan 1, 1993

By James P. Dorian

In 1990, the former Soviet Union ranked first worldwide in the production of asbestos, chromium, iron ore, iron and steel, lime, manganese, mercury, nickel, peat, potash, and titanium. Since the middle of this century, that nation had maintained one of the world's most valuable mineral industries, ranking number two in 1950 and number one in 1990. It is clearly an enormous mining industry, with more than 1300 enterprises and an estimated employment base of 1.2 million persons (Table 1). Despite its size and historical achievements, however, the mining industry of the 1990s in the former Soviet republics is encountering problems in performance, efficiency, transportation and utilization. The industry operates below full capacity and is plagued by outdated technology and equipment, rising production costs, capital shortages and labor strikes, in addition to general economic deterioration and civil unrest. Attempts to boost domestic minerals supply in the republics so far have failed because of economic difficulties. And the republics lack the financing required to initiate new, large-scale development projects.

Jan 1, 1992

By D. S. Bird

Kennecott Utah Copper began a modernization program in 1986 that was aimed at expanding and updating mining and ore process facilities at the company’s Bingham Canyon copper mine and concentrator near Salt Lake City, UT. Major components of the project included installation of an in-pit crusher, a transfer conveying system and a new ore concentrator with a design capacity of 70 kt/d (77,000 stpd). The Copperton concentrator was commissioned in February 1988. The grinding circuit is one of its principal features. It consists of three identical lines, each with a 10.4-m- (34-ft-) diam x 4.6-m- (15-ft-) long semiautogenous grinding (SAG) mill and two 5.5-m- (18-ft-) diam x 8.6- (28-ft-) long ball mills. The SAG mills are driven by two 4.5-MW (each) (6000-hp) variable- speed dc motors through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4.1-MW (5500-hp) synchronous motors coupled through a typical clutch-pinion gear-ring gear system.

Jan 1, 1995

By George A. Lawrence

A new super-large 100 m3 (3500 ft3) pneumatic mechanical flotation cell is now available to meet today's mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom round tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. The mechanism drive is either a customized right angle gear reducer or a conventional Vee belt drive. Both drive systems are available with an optional variable frequency control system that permits infinite speed adjustment of the rotor in each flotation cell or group of cells. Results of side-by-side comparative testing between three major manufacturers of super-large pneumatic mechanical flotation cells are discussed. These results were obtained at a large copper concentrator in Chile during several weeks of commercial scale testing.

Jan 1, 1995

By Raghoottama S. Pandurangi, Mohindar S. Seehra

A critical examination of the published results on the hemolytic ability of different forms of silica viz, quartz, cristobalite, tridymite and amorphous silica is made and it is concluded that quartz, cristobalite, and tridymite have nearly equal longterm abilities (within ±15%) but much larger than the hemolytic ability of amorphous silica when correctly compared on a per unit surface area basis. Also, a one-to-one correlation appears to be valid between the hemolysis and fibrosis studies. New results on the photoacoustic spectroscopy of amorphous silica particles heat-treated at 100, 200, 400, 550, 700, 820 and 1050°C are presented and it is observed that the intensity of the sharp silanol band at 3745 cm-1 and hemolysis by these particles have nearly the same temperature dependence. In contrast the intensity of the bulk IR modes (viz. the 797 cm-1 band) does not show any significant temperature dependence. These observations demonstrate that the surface SiOH species are involved in hemolysis by silica particles. Key words: silica polymorphs; hemolysis; silanol species

Jan 1, 1991

By Heinz Distelmeier

The New Austrian Tunneling Method was, as is well known, developed from conventional rock tunnelling. In Germany about 10 years ago the NATM began to be applied to partially stable soils by incorporated excavation and support methods to allow its use with these soils. The advantages of this tunnelling technique - adaptability, ecomomy, and quality have resulted in its widespread usage. Today, about 85 % of all mined tunnels in Germany are produced with this technology. This rapid development has resulted in about 40 companies operating within a geographical area about the same size as the state of Illinois that are capable of utilizing the NATM. In most cases German contract/award procedures allow the contractor to develop alternate design and plans. As a result of this flexibility and intense competition, safety factors have been gradually reduced to the lower limit of what could be regarded as demonstrably safe, and the utilization of the NATM has expanded to include higher risk conditions, namely * excavating larger cross sections. * working with less overburden. * work undertaken under less stable soil conditions.

Jan 1, 1983

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine's collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By C. T. Twort

As technology and economic conditions allow mines to operate at ever greater depths, increasing demands are placed on the environmental engineer to adjust the capacity of the installed mine . - refrigeration systems. At the same time the engineer must satisfy the changing legislation, which demands that developments are carried out in as an energy efficient and environmentally accept- able manner. Following the trends outlined above, this paper is written to give an overview of the current and potential future refrigeration technology available to the mining industry. The effects that may be produced by the adoption in mining applications of the new generation of 'green' refrigerants are examined both at the design stage and when considering the viability of retrofitting existing systems so that they comply with the Montreal Protocol. An introduction to the concept of Total Energy Warming Impact (TEWI) is provided, with an explanation of its use in optimising system design and performance, and its incorporation as part of an environmental audit strategy. The paper concludes with a discussion of innovative refrigeration techniques and the possible future developments in legislation.

Jan 1, 1997

Western Energy Co.'s Rosebud mine in Colstrip, MT, has implemented innovative mining techniques in the past,* and following in that tradition, new techniques for overburden removal were recently introduced at the Montana coal mine. In April 1979, falling coal production left Western Energy in a bind. At that time the company was one of the first to implement a dozer/scraper stripping system for additional stripping capacity. This time around, however, the challenge was to eliminate spoil rehandle with a dragline while digging down 33 in. "Rehandle will increase 20% by going down an additional 3 m past the 24-m level," according to Bob Cope, mine supervisor for Western Energy. To cut this additional expense by eliminating the need to rehandle, Western now uses scrapers to bench down for the dragline. This system utilizes the flexibility of scrapers as earthmoving tools. Although scrapers were originally purchased to fill an immediate need for productive, low-cost overburden stripping, they are now benching and continue to optimize the overall effectiveness of existing draglines. According to the company, the draglines couldn't keep up with production requirements if they had to rehandle spoil material. Benching with the scrapers eliminates spoil rehandle. Western Energy expects to produce 10.6 Mt of coal this year from three active pits in the Rosebud mine. Western estimates that there are enough coal reserves at Rosebud to support a 40-50 year operation. The sub-biturninous coal has an energy value of 9.2-9.4 Mj, 0.87% sulfur, 8% ash, and 20% moisture. Pit A, approximately 610 m long and 45-55 m wide, is the mine's greatest producer. A Marion 8050 dragline with a 46-ms bucket digs 30-33 m to uncover the 7.3-m Rosebud coal seam. Here, the scrapers were put to work benching for the dragline. Long Construction Co., which operates the mine equipment for Western Energy, uses four Caterpillar 637 tandem-powered scrapers, two Cat 631s and two Terex TS-24s. The number and combination of scrapers actually used for benching periodically changes, depending on which ones are needed for topsoil removal and reclamation. Scrapers benched down about 9 m and removed nearly 2.3 Mm of over-burden at pit A. About 1 Mm was placed in a 9-m lift on top of the high-wall at the head of the pit. The scrapers built up one side of the lift first and then the other on successive passes to

Jan 2, 1981

By Surendra K. Mishra

The increasing volume of wastes being generated by industry is a legacy of the industrial revolution and subsequent industrial growth. Social and regulatory pressures have been mounting on industry to improve its waste management practices. In many industrial sectors, waste disposal has been the only method of waste management. Land farming, underground burial, deep wells and incineration are still practiced. Often, concentration and volume reduction of waste streams are also practiced to reduce the waste management costs. In the recent years, there has been emphasis on waste minimization. Since the 19th century, industry has practiced recycling of usable resources as a way of handling unwanted byproducts. The mining industry has recovered or extracted economic minerals from tailings for decades. For example, during the gold rush period of 1970s, extraction of gold from tailings dams became economically attractive. Similarly, when it was economical, coal and shale fractions have also been recovered from tailings and refuge materials for commercial uses. In the steel industry, with the development of new furnace technology, recycling of flue dust and scrap iron was practiced as early as in the 19th century. Before 1900, there was little incentive for the industry to reduce the waste volumes. Manufacturers, however, did see a rationale for adopting profit-increasing techniques. They made an effort to recover and recycle economic materials from waste sources. One of the pioneering examples of resource recovery is the coke making industry. As the industry was market driven, products recycled from coke batteries included ammonia for use in fertilizers, gas for power generation and heating, and tar for road construction, wood preservation and roofing. Tar had been avery troublesome waste byproduct. But it quickly became a valuable chemical raw material, providing the foundation for Germany's dominance of the world's dye and medicine markets before World War I. Similar trends evolved in the chemical industry. In the context of current environmental regulations and escalating mining and processing costs, recycling of re- [ ] sources is becoming economically more attractive. Solid and liquid wastes generated by industries contain a range of inorganic and organic contaminants. Among these contaminants, metals and hydrocarbons form major groups. Treatment of these wastes is essential to meet regulatory disposal requirements. In the recent years, based on the principles of chemical and mineral process engineering, processes have been developed to treat these industrial wastes. This article reviews some of the processes that have made impacts and have proven to be effective at commercial scales.

Jan 1, 1999

By David Yankovich, Geoff Hughes, David Haug, Jon Kaneshiro

"In March 2013, the Sanitation Districts of Los Angeles County began final design of the Joint Water Pollution Control Plant (JWPCP) Effluent Outfall Tunnel project. The new, approximately 7-mile, 18-ft internal diameter tunnel will provide additional capacity and redundancy for the existing 8- and 12-foot diameter tunnels, which were built in 1937 and 1958, respectively. Connections to an existing, active 14-foot arch force main and four existing ocean outfalls ranging from 5- to 10-foot diameter are required. This paper will present geological features for the project, and details of the proposed post-tensioned tunnel liner and associated structures. INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) are 23 independent special districts serving approximately 5.3 million residents in Los Angeles County. Seventeen of the districts that furnish sewerage services to the metropolitan Los Angeles area are signatory to a Joint Outfall Agreement that provides for a regional, interconnected system of facilities known as the Joint Outfall System (JOS). The JOS service area is shown in Figure 1. The JOS serves an area that encompasses 73 cities as well as unincorporated territory and parts of the City of Los Angeles. The JOS provides wastewater collection, treatment, reuse, and disposal for residential, commercial, and industrial users, and it includes seven treatment plants, the largest of which is the JWPCP, located in the City of Carson. Currently, secondary treated effluent is conveyed through two 6-mile long parallel tunnels, 8- and 12-feet in diameter, from the JWPCP to a manifold structure located at Royal Palms Beach, near White Point on the Palos Verdes (PV) Peninsula, from which four seafloor outfalls extend offshore. The two main outfalls, 90- and 120-inches in diameter, extend approximately 1.5 miles offshore and discharge at a depth of approximately 200 feet below sea level. The other two outfalls, 60- and 72-inches in diameter, are used for additional capacity during heavy rain events and extend a shorter distance offshore and discharge at shallower depths. A schematic of the existing system with the proposed tunnel and structures is shown in Figure 2, and the proposed 18-ft diameter tunnel alignment is shown in Figure 3. Both existing tunnels and main outfalls are required to be in service at all times."

Jan 1, 2016

By J. E. Gebhardt, H. Toro, K. Y. Lee

Industrial-scale test results indicate superior metallurgical performance of column flotation compared to conventional cell flotation for copper cleaning. A technical comparison of bubble generation systems for column flotation is made. Two types of bubble generation systems are considered: the filter-cloth type spargers and the Turbo-Air® sparger, which utilizes an air-water mixture fed to the column through injection tubes. Examples of the improved technical performance available with an external sparger system are presented using data from plant tests conducted for specific applications with several different mineral ores. INTRODUCTION Column flotation is now a valuable unit operation which mineral processing engineers employ in the design and operation of flotation circuits in nearly all mineral applications. The acceptance of columns in the mid- 1980s by the minerals industry was paralleled by a rigorous approach to developing a scientific understanding of the design, scale- up, and operation of column flotation units (Finch and Dobby, 1990). Since then, column flotation has become a standard unit of the cleaning stage in many new mineral concentrator projects and has replaced older mechanical cells to improve process efficiency. The size of column cells has continued to grow from the initial 0.9- to 2.1 -meter diameter range, and it is not uncommon to find column cells today being 2.7- to 3.6-meters in diameter. With the success of the smaller units, the scale-up to larger cells has been proven and demonstrated by the performance of the large-diameter cells (Murdock and Wyslouzil. 1991). The use of columns in flotation circuits has also been accompanied by developments in modelling. control, and optimization of column performance (Lee et al, 1991). The bubble generation system is the heart of the operation of column flotation cells. The most common methods for generating bubbles can be divided into two types: the internal and external spargers. Internal spargers are typically a porous material, such as sintered glass, porous rubber or filter-cloth, or maybe a single- or multi-nozzle sparger. External spargers implies that a gas and a liquid (either water or slurry) are brought into contact outside the column and that mixture is then introduced into the column. Several types of external spargers are available today, and innovative designs for externally mounted air sparging systems have been a significant factor in the successful application of columns. Early types of bubble generation systems.

Jan 1, 1993

By Gregory M. Rumbaugh, Christopher Mark

"The proliferation of unconventional gas well development in the Northern Appalachian coalfields has raised a number of mine safety concerns. Unconventional wells, which extract gas from deep shale formations, are characterized by gas volumes and pressures that are significantly higher than those observed at many conventional wells. The gas is composed largely of methane as well as other hydrocarbons. Hundreds of planned and actively producing wells penetrate protective coal pillars or barriers within active mine boundaries, including chain pillars located between longwall panels. Gas released from a well damaged by mining-induced ground movements could pose a risk to miners by flowing into the mine atmosphere. The mining-induced ground movements that may cause well damage include conventional subsidence, non-conventional subsidence (e.g., bedding plane slip), pillar failure, and floor instability. This paper describes the known risk factors for each of the four failure mechanisms. It includes a framework that can guide the risk assessment process when mining takes place near gas or oil wells.INTRODUCTIONSouthwestern Pennsylvania has served for centuries as a producer of coal, oil, and natural gas. Coal mines were first developed in the Pittsburgh Coal Seam in the 1760s, with the first recorded mine in 1761 being the Fort Pitt Mine (Edmunds, 2002). Natural gas was introduced to the region when the Haymaker Well in Murrysville, Pennsylvania experienced a blowout on November 3, 1878. Although it was originally drilled prospecting for oil, it produced an estimated 30 million cubic feet per day of natural gas. Without well controls or pipeline infrastructure in place, it burst into flames and lit the night sky for over a year. Soon after, the Penn Fuel Company continued development of the Murrysville gas field and is credited with making Pittsburgh, Pennsylvania the first major city in the U.S. to have natural gas supplied for home and industrial uses. “Natural gas is king in Pittsburgh,” proclaimed an October 18, 1885, article in the New York Times headlined “Value of Natural Gas, Its Use Clarifies the Atmosphere at Pittsburgh” (AOGHS, 2018). By the early 1900s, coal, oil, and natural gas production had reached the southern extents of Pennsylvania in Greene County. The county had first produced oil in 1886, and shortly after began producing natural gas in 1890. By 1906, over 1,300 wells had been drilled (Stone and Clapp, 1906)."

Jan 1, 2019

By James M. Barker, George S. Austin

Stone, one of the oldest building materials, today remains a well-established material throughout the construction industry. The use of natural stone is much less prevalent now than in the past. It is still widely considered to be the most aesthetically pleasing, prestigious, and durable building material. New and re-opened quarries are coming onstream to meet increased demand related to new building technology and increased residential use of stone. CLASSIFICATION No classification can completely eliminate overlap between dimension stone, aggregate, and decorative stone because most stone is multi-purpose. Many used for decorative purposes are not produced specifically for that end use. Rock otherwise considered waste in dimension stone or aggregate quarries can be decorative stone coproducts (Fig. 1). Many uses require a compromise between decorative and structural qualities (Bowles, 1992, written commu¬nication). Shipley (1945) used decorative stone interchangeably with or¬namental stone. Gary et al. (1972) defined decorative stone as that used for architectural decoration, such as mantels, columns, and store fronts, but added that it is sometimes set with silver or gold in jewelry as curio stones. Bates and Jackson (1987) also restricted decorative stone to that used for architectural decoration. Meanings of otherwise identical terms used in the stone industry differ be¬tween geologists, engineers, and quarriers. They often carry a much broader meaning for quarriers and engineers compared to their very specific use by geologists (Makens et al., 1972). Decorative stone, including ornamental stone, is more broadly defined by geologists as any stone used primarily for its color, texture, and general appearance. It is not used primarily for its strength or durability, such as construction stone, or in specific sizes, such as dimension stone. The decorative stone industry uses a much wider range of stone types compared to stone that is dimensioned. Decorative stone usually serves some structural pur¬pose, but is not load-bearing to any great extent. Weak or costly stones serve in decorative, not structural, applications. STATISTICS AND END USES Decorative and dimension stone data are difficult to separate because the US Bureau of Mines keeps statistics only on dimension stone and crushed stone. The value of domestic dimension stone production in 1990, which includes some decorative stone, was about $210 million compared to imports of about $524 million and exports of about $35 million. Production was 1 080 t of which at least one-third was for decorative uses (Taylor, 1992). The principal uses are rough blocks in building construction (23%) and monu¬ments (18%); the remainder is used as ashlar (18%), curbing (12%), and miscellaneous (29%). Major rock types are granite (50%), limestone (30%), sandstone (10%), slate (3%), marble (2%), and other (5%) (Harben, 1990). Crushed stone valued at $5.6 billion was produced in the United States in 1990 by 1700 companies operating 3400 active quarries in 48 states (Tepordei, 1991). About 52% is used in con¬struction, 9% in cement and lime manufacturing, 2% in agricul¬ture, 2% in industrial uses, and 35% for unspecified uses including decorative aggregate. Limestone and dolomite comprise about 71%, granite 14%, and traprock 8% of the stone crushed in the United States. The remaining 7% are, in descending quantity, sandstone, quartzite, miscellaneous rock, marble, shell, calcareous marl, volcanic cinder and scoria, and slate. The basic types of decorative stone are: rough stone, aggregate, cut or dressed stone, and manmade stone [(Table 1)]. Rough Stone Rough stone is used as it is found in nature with very limited processing such as minor hand shaping, edge fitting, and size or quality sorting (Perath, 1992, written communication). This stone type is often marketed locally in relatively small tonnages and includes fieldstone and flagstone. The primary end uses of rough stone are landscaping, edging, paving, or large individual stone landscape or interior accents [(Fig. 2)]. Fieldstone: Fieldstone is picked up or pried out of the ground (gleaned) without extensive quarrying and includes garden or large landscaping boulders (Austin et al., 1990, Hansen, 1969). Boulders and cobbles may be split or roughly trimmed for use in rubble walls and veneers, both interior and exterior. Popular fieldstone rock types include sandstone, basalt, limestone, gneiss, schist, quartzite, and granite, but many others are suitable. Much fieldstone is col¬lected by individuals or small companies because the industry is labor intensive and markets are small. The stone may be sold locally in small quantities from the back of vehicles (Austin et al., 1990). Fieldstone includes many rock types, sizes, and shapes with the only common denominator that it must be set by hand and be durable (Power, 1992, written communication). Moss Rock. Moss rock is fieldstone partially covered by algae, mosses, lichens, and fungi that give the rock an aged and variegated patina (Austin et al., 1990). The plants are supported by moisture and nutrients in the stone. Moss rock is used for landscaping, walls, and fireplaces. Although almost any durable rock can be a moss rock, most are slabby or rounded sandstone and limestone (Fig. 3). Flagstone: Flagstone or flagging consist of thin irregular slabs used for paving, walkways, and wall veneers. Random-shaped flagging is produced widely in the United States. Suitable stone

Jan 1, 1994

By S. Peng, N. Vayenas, A. Farah

"While genetic algorithms have been widely adopted in ore grade estimation and optimization, mine design, and production scheduling in the mining engineering field, reliability and maintainability analysis of mining equipment using genetic algorithms has been a relatively new research area in recent years. This paper presents an application of genetic algorithms using case studies with seven underground scoop trams whose maintenance records have been collected over a period of 12 months from an underground mine in the Sudbury mining area. Based on the assumption that various factors that contribute to machine failures resemble the biological evolution process, the authors have developed an in-house PC software application called GenRel which adopts genetic algorithms in its programming. In this study, the authors feed the historical maintenance data into GenRel in order to predict future maintenance characteristics of mining equipment in a time period of three months. Then the predicted maintenance characteristics are compared to the actual maintenance records in the same time period. A statistical study is then used to examine the similarity between the predicted data and the recorded data.INTRODUCTION Today maintenance costs of sophisticated engineering systems are so high that maintainability draws great attention from scientific researchers to operations managers. For instance, a study by [1] shows that American manufacturers spend more than 300 billion U.S. dollars on plant maintenance and operations. Therefore it is understandable that the main objectives of applying maintainability principles to engineering systems are to reduce projected maintenance costs, to use maintainability data to estimate system or equipment availability/unavailability and to determine labor-hours and other related resources needed to perform the projected maintenance. A system with better maintainability would inherently provide the benefit of lower maintenance costs, less time to recover with lower breakdown frequency (design for simplicity), less complexity of maintenance tasks and relatively reduced man-hours [2]. Most maintainability functions use the Time To Repair (TTR) as the independent variable. It is common to use probabilistic or statistical concepts to define a maintainability function, for example, the probability density function. Let t denote the time. Assuming a repair starts at t=0 and completes at time T, the maintainability can be mathematically defined [3] as in Equation (1)."

Jan 1, 2015

By Saverio Agresti, Giuseppe Lunardi, Donato Basta, Roberto Trapasso

"At a distance of 10 years from the first application of the Nazzano Method, the widening under traffic of a tube of an existing motorway tunnel was realized near Ancona, along the A14 Motorway in Italy. This paper describes the works for the enlargement with conventional method of the second tube, very close to that already widened under traffic.This enlargement was realized very fast, taking into account the advantages of some interesting technological improvements of the Final Design proved in the first tube.INTRODUCTION TO THE WIDENING OF EXISTING MOTORWAY TUNNELSThe widening of a twin-bore motorway tunnel usually considers the double option of creating a third bore as an alternative or closure to traffic of one of the two bores with the resulting reduction in the level of service for users.On the contrary, the extension in situ of a road, motorway, railway or underground tunnel in the presence of traffic, made possible by an inspired idea of Prof. Pietro Lunardi, enables the level of service of the infrastructure to be maintained without the need to resort to alternative routes to create new permanent or temporary bores, not always feasible because of the lack of the necessary space.This construction technique, known as the ‘Nazzano Method’, is part of the technologies refined and offered by the ADECO-RS approach to tunnel design and construction (Lunardi P., 2008) which is increasingly used in the world, leading to the industrialisation of tunnelling (meaning respect for the times and costs set out during detailed design) both in conventional and mechanised (through TBM) excavations.The first true experimentation of the ‘Nazzano Method’ was carried out between 2004 and 2007 to enlarge the two-bore ‘Nazzano’ tunnel (Italy, Milan-Rome A1 motorway) in the presence of traffic, widening it to house from two to four lanes in each direction (Lunardi P. et al., 2007). Following the success achieved in this first application, the Nazzano Method was strengthened considering all the possible suggestions arising from the previous experience and then taken up to enlarge the north bore of the ‘Montedomini’ two-bore tunnel (Italy, Bologna-Taranto A14 motorway), in situ and the presence of traffic."

Jan 1, 2016

By Franz Wilhelmstoetter, Christian Karner

"The Confederation Line is phase one of Ottawa’s light rail transit, which consists of 13 stops and stations. The project’s center piece is a 2.5 kilometer (1.6 miles) long tunnel with three underground stations leading underneath downtown Ottawa and is constructed within feet of adjacent buildings. The downtown stations, Lyon and Parliament, are caverns approximately 16.5 m (54 ft) by 18 m (59 ft) in a horseshoe configuration constructed in rock, while the third station, Rideau, is approximately 22 m (72 ft) by 18 m (59 ft) in an oval configuration and constructed in mixed ground. The paper will discuss design decisions made early on in the project such as excavation method, unique construction sequencing, and equipment selection, and go on to include corresponding progress rates. The paper also documents design and construction challenges of large caverns in very close proximity to existing buildings and varying ground conditions. Finally, an overview of achieved construction milestones and a current construction progress will be presented. Station cavern excavation is expected to be completed in early 2016. INTRODUCTION The number of urban metro construction projects has certainly increased over the last decades. Cities are growing rapidly all over the planet and many are striving to keep up with the increased demand for public transportation. One of the most feasible types of inner-city transportation with the capacity for large quantities of passengers are metro (subway) systems. Still, large construction projects in dense urban areas often affect the city’s residents in mostly negative ways. During construction, residents face the obstacles of road closures, noise, dust, economic loss for businesses, and property value losses are common. In other words, individuals are directly affected by the way new infrastructures are planned, designed, built and operated. The tunneling industry offers unique opportunities of keeping these side effects to a minimum and possibly avoiding them all together. Although challenged by a variety of constraints (some of which will be discussed in this paper), urban tunneling applications offer a chance to keep cities environmentally, economically, socially, and culturally sound during construction."

Jan 1, 2016

By Pan Eimon

She was young, beautiful, intelligent, virgin. Her name was Barbara and she captured the attention of many men, especially those in dangerous occupations. Her rich and doting father was hopeful of making an advantageous marriage for his daughter. Instead, she defied him, became a Christian, and refused to marry. Traumatized, he killed her and was himself struck dead by lightning. That is not the plot of a new soap opera. It is the melodramatic story of a Turkish teenager who was martyred in the third century but lives still as patron saint of mining. The story begins with a 20th century fact. Santa Barbara is a figment of imagination - perhaps based on an early oriental folk heroine, embroidered by a seventh century storyteller, and reworked by a ninth century Greek martyrologist. The authoritative Lives of the Saints reports: "There is ... Considerable doubt about the existence of a virgin martyr called Barbara and it is quite certain that her legend is spurious. There is no mention of her in the earlier martyrologies, her legend is not older than the seventh century, and her cult did not spread until the ninth." The Catholic Dictionary adds that the Barbara story is probably "a pious legend." Widely revered Santa Barbara was one of the most widely venerated saints of the Middle Ages. She became the patron, not only to miners, but also to artillerymen, engineers, architects, builders, stonemasons, gravediggers, and sailors. Mines, mountains, churches, and places bear her name. Barbara's feast day, Dec. 4, appears on the most ancient holy day calendars. And a Barbara festival is still celebrated throughout central Europe, in Spain, and in mining areas of Latin America on that date. The Pacific coast channel, the city, and the mission of California are named for Santa Barbara. An expedition, sailing that coast under Viscaino in 1602, was saved from shipwreck on Dec. 4 after the sailors prayed for Barbara's intervention. Franciscans gave her name to the modern Franciscan Province of Santa Barbara, which embraces six western states and the Philippine Islands. Barbara is intimately entwined with mining. The origins of both saint and profession are lost in an-

Jan 11, 1985

By P. Bottomley, M. Matthews

Maintaining an acceptable thermal environment in South African gold mines becomes increasingly difficult as mining progresses to greater depths where higher virgin rock temperatures are encountered. Current environmental practice offsets the resulting high heat loads by installing large refrigeration plants. However, with the continued escalation of refrigeration costs, it has become necessary to examine other methods for economically combatting the underground heat load. The Chamber of Mines Research Organization has recently been pursuing a programme to devise methods of reducing the flow of heat into underground workings at source. Although there are several sources of heat (such as machinery, men, and explosives), the most significant is that from the rock mass surrounding the workings (Bluhm et al., 1986a). The main thrust of the work has therefore been directed at predicting and devising methods of reducing this heat source. A great deal of theoretical work has been carried out on the prediction of underground heat flow. From a review of this work (Bluhm et al., 1986b) it became apparent that there are two major aspects which require attention, namely algorithms for predicting the heat flow around the advancing stope face, and a correlation of the theoretical work with accurate empirical data. In order to remedy this situation, new theoretical models have been developed (von Glehn and Bluhm, 1986), and heat flow measurements have been made in both a conventional stope (Bluhm et al, 1986a) and in a backfilled stope (Matthews u., 1987). A number of methods for reducing rock heat flow are being examined. These include the insulation of intake airways (Bottomley, 1985 ), backfilling with waste material of the worked out areas, and alternative approaches to the design of mining layouts, the mining method, and the choice of cooling strategy. This paper highlights the heat load reductions that can be achieved by backfilling the worked-out areas and by adopting concentrated mining. The first part of this paper summarizes the results of the measurements obtained in the conventional and backfilled stopes. The theoretical models are then described and comparisons are made with the measured values.

Jan 1, 1987