Search Documents

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By L Singheiser, W. Willenborg, M. Mueller, K. Hilpert

The limitation of fossil fuel resources and the necessity of reducing CO2emission require an increase of the efficiency of power plants by using combined cycle power systems. Pressurized Pulverized Coal Combustion (PPCC) is a potential concept to realise these objectives. The direct use of hot flue gas for driving a gas turbine requires a hot gas cleanup to achieve corrosion prevention of the turbine blading. One of the main problems is the alkali release during the coal combustion process. Molten coal ash slag has a high potential for alkali retention which depend son the alkali oxide activity in the slag. Knudsen Effusion Mass Spectrometry (KEMS) was used to determine thermodynamic data of alkali gas species over molten coal ash slags and of alkali oxides in molten coal ash slags. The main interest of the investigations focused on the structural dependence of the thermodynamic properties of the alkalis. It was found that there is a strong correlation between the thermodynamic properties and the ratio of nonbridging oxygen to tetrahedral oxygen (NBO/T). An increase of the polymerization of the slag results in a decrease of the alkali oxide activity in the slag and thus a decrease of the alkali partial pressure over the slag. Keywords: coal ash slag, structure, alkali oxide activity, alkali vapour pressure, PPCC, KEMS.

Jan 1, 2004

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By T. Celik, B. Genc, C. Musingwini

"This paper discusses a new methodology for defining and measuring mine planning software utilization in the South African gold mining sector within an evolving data-set framework. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgyin 2013. In 2014 the data-set was updated with additional and new information. Using the 2012 and 2014 timestamps, a methodology for estimating the software utilization was developed. In this methodology, the three variables of commodity, functionality, and time factor were used to define and measure the software utilization in order to ultimately inform decision-making strategies for optimal software utilization. Using six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation, and Optimization, utilization in the gold sector was measured. This paper presents the methodology employed for measuring the mine planning software utilization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and who want to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2015

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By S. T. Camagu, J. Dutta Majumdar, S. L. Pityana

Laser surface alloying was used to develop copper and molybdenum aluminides by injecting premixed copper and molybdenum powder particles into a laser-generated melt pool on an aluminium substrate. Different laser processing parameters were used to produce the composite thin layers on the substrate material. The microstructure and phase constituents of the composite layer were studied by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) techniques. Experimental results show that the matrix structure of the metal matrix composite layer consists of ?-CuAl2and MoAl5. Surface hardness was increased by a factor of 3.

Jan 1, 2015

By A. Patri, D. S. Nimaje

Wireless sensor networks and wireless communication systems have become indispensable in underground mines. Wireless sensor networks are being used for better real-time data acquisition from ground monitoring devices, gas sensors, and mining equipment, whereas wireless communication systems are needed for locating and communicating with workers. Conventional methods like wireline communication have proved to be ineffective in the event of mine hazards such as roof falls, fires etc. Before implementation of any wireless system, the variable path loss indices for different workplaces should be determined. This helps in better signal reception and sensor node localization, and also improves the method by which miners carrying the wireless devices are tracked. This paper proposes a novel method for determining the parameters of a suitable radio propagation model, which is illustrated with the results of a practical experiment carried out in an underground coal mine in southern India. The path loss indices, along with other essential parameters for accurate localization, have been determined using the XBee modules and ZigBee protocol at 2.4 GHz frequency.

Jan 1, 2015

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 357 to 366 for the year ended 30 June 2002. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2002 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 26 July 2002 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2002 set out on page 357 to 366 wereapproved by the Council on 26 July 2002 and are signed on its behalf by:

Jan 1, 2002

By Z. van Zyl

The southern African coal industry is facing the reality that coal reserves are becoming deeper and harder to mine than before. Alternative visions need to be considered to offset the impact of these challenges on productivity, cost, and profitability. One of the main challenges is to maintain current production levels under more difficult conditions, and improve productivity where conditions allow. There is a need to move from the reactive event-based management system towards the more adaptable and flexible process-based management system. This paper focuses on underground coal mining, but the principles are also applicable to other commodities and mining methods. This paper is based on research undertaken by the personnel from Mining Consultancy Services Pty Ltd (MCS) on trends in the underground coal mining sector, as well as practical experience over a period of 16 years in the field of electronic monitoring of mining machinery and productivity optimization.

Jan 1, 2015

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

By F. T. Cawood

This paper focuses on the role of the coal mine surveyor at the start of the 21st century. It demonstrates that surveyors must look beyond their legal appointment and pursue opportunities to add value at an operational or corporate level of the company. It also exposes the shortfall of statutory appointments in defining the surveyor?s role in terms of key business drivers of the company. One such an opportunity is the potential role of the surveyor in mineral accounting and quality assurance to meet mine requirements, market specifications and standards pertaining to corporate governance and reporting. Finally, some thoughts are expressed on what can be done to elevate current practice to best practice and how to achieve this goal

Jan 1, 2007

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By Mauri Kauppi, Pekka Niemelä

World HCFeCr production is 6.0 million tonnes. Correspondingly 1.1-1.6 t slag / t FeCr is produced depending on the raw material basis. Essentially all FeCr is produced in submerged arc furnaces, while the role of competitive technologies like DC is limited. In all furnaces fluxes are used to optimize the slag composition. Vital characteristics are smelting point, electric conductivity and viscosity. The main components of FeCr slag are SiO2, Al2O3 and MgO. Additionally it consists of Cr-, Fe-oxides and CaO. Granulated slag and/or classified slag products are produced depending on the production process. The slag products are mainly marketed in road and civil construction purposes but also in producing refractories. Normally crushed and screened slags are produced simultaneously when recovering alloy. The leachate of slag products is low and performance results are excellent. Slag products successfully replace natural sand and macadam. Generation of waste is essentially reduced. Producing and using slag products are described as BAT-technology and it is an essential environmental aspect. Outokumpu Tornio Works produces 320 000 t FeCr-slag/a. This paper deals with formation of slag in smelting process, its chemical composition, physical and structural characteristics, utilization and product specifications as well as environmental aspects. The slag products are standardized and CE marked. Additionally the role of slag in smelting and alloy recovery is reviewed in this paper.

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By A. D. Pelton

The evolution of thermodynamic models of molten salts and slags, starting with Temkin in 1948, has culminated in today?s sublattice models. These modern models have permitted the development of large thermodynamic databases of model parameters, which can be used to calculate and predict accurately the properties of multicomponent solutions. The model parameters are mainly obtained by the critical evaluation and optimization of available thermodynamic and phase equilibrium data for binary and ternary subsystems. The models are then used to estimate the properties of multi component slags and salts from these assessed binary and ternary parameters. When used in conjunction with thermodynamic databases for solids and solid solutions (salts, oxides, sulphides, metals, etc.), other liquid solutions (such as liquid metals),and gases, these databases permit the calculation of complex multiphase equilibria in multicomponent systems, with applications in a wide variety of industries. These calculations can be performed with general commercial software for Gibbs energy minimization, which can also be incorporated into process simulation software packages. Keywords: slags, salts, solution models, thermodynamics, phase diagrams, oxide systems, molten salts

Jan 1, 2004