Search Documents

By N. A. Barcza

This paper describes the development of large-scale thermal-plasma systems, which was motivated, in general, by the potential cost savings that could be achieved by their use as a replacement for the more conventional methods used in the generation of thermal energy. The anticipated cost savings arise not only from the use of plasma-generating devices but from the manner in which they have been interfaced with a furnace to process particular materials, mostly as fines. Thermal-plasma systems fall into two categories: non-transferred-arc and transferred-arc devices. In general, transferred-arc devices have been interfaced with open-bath furnaces in which melting or smelting processes carried out, while non-transferred-arc devices have normally been applied to shaft furnaces. Water-cooled transferred-arc devices are somewhat limited in power (about 5 MW) because of the relatively voltages (300 to 500 V) that can be attained in open-bath furnaces, where very long arcs are undesirable, and because only relatively low levels of current can be carried. Graphite electrodes can overcome the restriction current, and power levels of 30 to 50 MW seem feasible, even with one electrode, if direct current is used. Multiple water-cooled devices are capable of attaining similar power levels, but the capital costs are much higher. Costs due to electrode wear are lower for water-cooled systems, but expensive gases are needed for transferred-arc devices. Mintek conducted extensive pilot-plant work in which water-cooled devices were used initially but graphite electrodes were used subsequently to produce ferochromium from fines. Transferred-arc open-bath configurations were used. This work led to a decision by Middelburg Steel & Alloys (MS&A) to install a 16 MVA furnace of semindustrial scale to produce ferochromium aloys based on the ASEA d.c. arc furnace developed for the Elred process. Non-transferred-arc devices have atained reasonable scale-up to the 6 to8 MW power level, and high-voltage operation, which is inherent in such devices, has enabled lower currents to be used. Nevertheless, multiple systems are still necessary to accommodate large-scale applications, and this can be costly from a capital point of view. The cooling requirements are large, and can represent a considerable loss of electric energy. Shaft furnaces equipped with non-transferred-arc devices are suitable for the processing of materials that have volatile species, e.g. silica or manganese, or where the shaft is used to prereduce oxides that are amenable to gas-solid reactions. It is probably in the treatment of light and refractory metals that plasma technology will achieve its greatest development in the years to come. The energy requirements for the production of these metals are high, and very low oxygen potentials are necessary. These are factors that favour thermal plasma. Much developmental work is still needed in this interesting field. It should be remembered that electrically generated thermal energy is a unique temperature source that, in many instances, cannot be replaced technically or economically by the combustion of a fuel.

Jan 1, 1986

By V. Korobko, M. Byantogtokh, N. Byambadorzh, V. Bysov

A three-stage operative planning of mining operations in ore opencasts is considered. The hierarchy of monthly-weekly, weekly-daily, daily-shift planning is offered. For the fastest elimination and deviations in problematic situations a level is analysed and weekly-daily or monthly-weekly operative plans are being constantly updated. Operative planning is formulated on information received of preparation and working of mining panels. The electronic maps of these panels are considered for automated operative planning. On the data of the registration of blasthole drillings on a panel, the position of blasthole entry, their depth and the number of a line are determined. The geologist specifies boundaries of ore grades by the bored silt. The qualitative characteristics of ores are determined by the chemical analysis of slime or magnetic logging of blastholes. The missing geologic information is obtained by interpolation on the data of detailed and operational explorations. During working of the mining panel the technologists mark the movement of shovels, associating this movement to blastholes. For this purpose technological attributes are used: when was the blasthole drilled, what drill-rig participated in drilling, what shovel was used and when was it worked? Around each blasthole the zone of its influence is built up. It represents a discrete, elementary volume of ore or waste. The discrete form of the data is most convenient, as it allows step-by-step methods to be employed of the scheduled tasks in many and various combinations. The account panel working technology avoids ‘combination’ explosions. The elementary blocks should be placed in a trajectory of shovel movement and the trajectory can not be arbitrary. It’s determined by the technological rules of extracting and loading of mine mass. In linking to blastholes, the trajectory of shovels is simulated by the sum of step-by-step moving from one elementary block to another. For this purpose a geometrical linkage of blastholes is used. At a railway haulage, or complete mining with truck haulage, the trajectory of movement is a shuttle along the front of operations in the panel. At a selective mining of ores the number of possible directions is limited to three: moving of a shovel by idle running along the front of operations in the panel, frontal pull all the way down of the panel, and withdrawal. The technologically acceptable trajectories of shovel movement are stored for the following estimation and selection of the best. The estimation is carried out on mathematical models with criteria on the method of the least squares of deviations based on preset parameters from the plan, uniform loading of shovels, and mixing of ore at unloading points. The equations of balance type and directive parameters of the plan, as well as technological restrictions of solid and of elementary blocks within the limits of a trajectory are the restrictions of the model. Depending on an industrial situation it is possible to choose one of the predetermined models. The presented technique is used for longitudinal shovel bench at the Erdenet ore-dressing company.

Jan 1, 2003

By B. Orgilbayar, B. Unursaikhan, S. Sukhbat, Ts. Zagarzusem, D. Baasanjav, L. Jargalsaikhan, E. Otgonjargal, N. Sugir-Erdene, Ts. Soyolmaa

This study has investigated the efficacy of the gravity beneficiation method based on gravitation and centrifugal forces for manganese ore. Powdered samples of manganese ores from the Unagad deposit in Mongolia were analysed for their element and mineralogical composition using ICP-MS and X-ray powder diffraction (XRD). The analysis presented the mineralogical compositions of the ores as hydro goethite, manganese minerals and magnetite, gangue minerals as quartz, albite, orthoclase and microcline of manganese ore. Manganese minerals are white in colour and have micro-veinlet, fine grained-aggregates associated with gangue minerals. The most important manganese minerals are hausmannite, pyrolusite, rhodochrosite, and manganosite. The composite of feed containing 17.31 % Mn and 36.3 % SiO2 was processed in a shaking table. In the experiment, a concentrate assaying 41.37% Mn was obtained from this composite with 65% recovery. In another experiment, f80=0.074 mm particle size ore was used in the MGS concentration test. A concentrate containing 38.34 % Mn with 75.2% recovery was produced in this experiment. The results showed that it is possible to obtain concentrate through gravity processing of manganese ore, which is an economically beneficial process for producing a product of a standard requirement. Keywords: Manganese ore, gravity separator, centrifuge, shaking table 1. Introduction

Jan 1, 2020

By R. H. C. Andrew

With the advent in recent years qf mechanization in deep-level gold and platinum mines, large quantities of rubber was are being used on both production and support vehicles. Conditions in these types of mines are extremely harsh and, as a result, we performance is significantly lower than in other types of mining such as open-cast base metal mining, where more favourable conditions prevail. Various options are available to the user to reduce tyre costs, including the use of retreads, the filing of tyres, and the repair of damaged tyres. While these methods may be generally successful in open-cast conditions, their use in deep-level mining needs to be carefully evaluated for each particular set of conditions. A basic requirement for any evaluation of we costs is the availability of reliable data on tyre performance and, for this reason, it is essential that proper tyre records are maintained This paper reviews the performance of tyres in deep-level gold and platinum mines in Johannesburg Consolidated Investment Company, Limited (JCI) over a period of about 8 years, and shows how the costs of retreading and tyre filing can be evaluated in practice. It also discusses the cost implications of repairing damaged tyres.

Jan 1, 1994

By F. L. D. Cloete, A. K. Haines, T. D. Sampson, T. H. Tunley, W. A. M. te Riele

The recovery of zinc from pickle liquors by ion exchange A. K. HAINES. Ph.D. (Visitor) T. H. TUNLEY. B.Sc;.(Chem.Eng.)(Visitor), W. A. M. TE RIELE. pr, Eng.. Ph. D. (Visitor), F. L. D. CLOETE. M.Sc. (Chem..Eng.)(Visitor), and T. P. SAMPSON. Pr. Eng.. BSc, (Chem.Eng,). B. Econ. (Visitor) Picklers and galvanizers in and around Johannesburg are encountering an ever-increasing problem in disposing of spent liquors from their hydrochloric acid pickling baths. Particularly troublesome is the zinc-contaminated liquor that is produced as a result of the clean-up of rejects from the galvanizing operation. Because of the volatility of zinc chloride. this liquor presents difficulties when processed in a conventional pyrohydrolysis acid-recovery unit. The paper describes the Metsep Process. developed by the National Institute for Metallurgy and Woodall-Duckham S.A. (Pty) Ltd. which involves the use of continuous ion exchange for the separation of the zinc from the pickle liquor. and the use of liquid-liquid extraction for the conversion of zinc chloride eluate to salable zinc sulphate. A description of laboratory and pilot-plant tests is given. and the approach used in the design of a full-scale continuous- ionexchange plant is outlined.

Jan 11, 1973

By T. Wennberg

An elevated location of a paste thickener on a ridge close to the disposal area is considered at a Swedish iron ore mine. About 0.7 M tonnes of thickened tailings are planned to be layered as paste in the vicinity of the thickener over several years with pipeline lengths of up to 900 m after about 20 years. In order to clarify the pipeline pumping characteristics of the tailings product for volumetric solids concentration from 40 to 50%, experiments in loop systems with pipeline inner diameters from 0.063 to 0.152 m have been carried out with various types of pumps. The results and comparisons carried out here showed that the performance of centrifugal pumps cannot simply be related to the rheology, but factors related to pump design and build-up tendencies of material within the pump and other particle properties may be of equal importance. During the first years of operation only one thickener underflow pump is required. The reliability and performance for various pump configurations are planned to be investigated systematically in order to meet the most effective long-term solution for paste thickener operation, pipeline distribution and placement in the disposal area as the discharge point advances over the life of the project.

Jan 1, 2007

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

By A. L. Edwards

A retrospective study was conducted on the Rand Mutual Assurance (RMA) noise-induced hearing loss (NIHL) compensation claims from 1998 to 2008 to determine if the 2008 milestone agreed at the 2003 Mine Health and Safety Summit was achieved. The number and costs of NIHL compensation claims in different commodity sectors and workplaces were collated. A secondary analysis of the ages of employees compensated after 2008 was conducted. A complementary retrospective analysis of audiogram data investigated the percentage loss of hearing (PLH) shift in different homogeneously exposed groups and occupations at two gold mines. The compensation claims analysis indicated a significant decrease in NIHL claims from 1998 to 2008, but the milestone was not achieved. The reason may be either that claims have not been submitted timeously as required by Instruction 171 and that the current submissions are a result of pre-2003 noise exposure, or that employees who were baselined are still developing NIHL owing to ineffective hearing conservation programmes in place in the mining industry. On the basis of best practice for hearing conservation, recommendations are made for leading indicators in hearing conservation programmes and for reducing the risks of NIHL in order to achieve the 2013 milestone.

Jan 1, 2012

By F. L. D. Cloete

The following discussion relates to the paper by G. S. Hansford, C. D. Levy, and J. W. de Kock that appeared in the March 1976 issue of the Journal (vol. 76, no. 8, pp. 363-369) Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RI00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Engineering in South West Africa The SW A Engineering Profession Steering Committee was established on 4th April, 1977, its purpose being to formulate an Act covering the engineering profession in South West Africa.

Jan 1, 1978

By P. J. D. Lloyd

The Federation of Societies of Professional Engineers (FSPE) recently conducted a survey of professional engineering manpower in South Africa. This article presents the data relevant to mining and metallurgical engineering. FSPE in their survey attempted to determine the supply of engineers in South Africa both from local universities and by immigration. The immigrants gave some problems in that it is difficult to know whether a man who claims to be professionally qualified really is. However, it was estimated that the ratio of immigrants who claimed to be qualified to those who really are the equivalent of our local graduates was between 1,0 and 1,9 for mining engineers, and between 2,0 and 4,1 for metallurgical engineers.

Jan 1, 1980

By M. Timucin

High-temperature phase relations and thermodynamics of the condensed phase region of the Pb-S-O system at 1473 K were analysed by use of the available information. The sub-regular solution models on Pb-PbS and PbO-PbSO4 continuous melts were used in conjunction to generate a consistent set of thermodynamic and phase equilibrium conditions for the Pb-S-O system. The directions and distributions of conjugation lines between melts of this system were derived with relevant activity and composition data. The calculations permitted the thermodynamic analysis of direct lead smelting and the construction of isothermal reaction diagrams for the system in terms of oxygen and sulphur partial pressures at 1473 K.

Jan 1, 1989

By T. Dimillo, R. G. B. Pickeirng

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular ore bodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focussed on the haulages, cross cuts and raises. The non-explosive rock breaking method has many other applications, however, it is the integration with the Tunnel Digging Machine that results in the first, cost effective, Continuous Tunnelling Machine for hard rock mining.

Sep 1, 2001

By C. J. Fauconnier

The various methods of detecting fires and heatings in collieries are reviewed. The methods described range from those relying principally on human senses to sophisticated methods employing infrared technology to detect traces of the products of oxidation and combustion. The advantages and disadvantages of various gases employed as indicator gases for the early detection of heatings and fires are discussed, and recommendations are made in this regard. The operation of a modern infrared carbon monoxide detection system is described, and the differences in operation and application of telemetric systems, tube-bundle systems, and up cast-shaft monitors are discussed In conclusion, some indication is given of the capital outlay required for typical early-detection systems.

Jan 1, 1981

By C. P. S. Barnard, D. G. Krige

Objective justification on economic grounds for expenditure aimed at improving the quality of the underground working environment requires a suitable measure of any improvement in productivity that would result under routine working conditions. For this purpose, a composite production criterion is suggested, as well as its correlation under actual operating conditions with various factors directly affecting productivity and the environment. Of the environmental factors, wet-bulb temperature appears to be the major factor affecting productivity. The production data given indicate that a decrease in the wet-bulb temperature of 1OC can be expected to result, on average, in some 3 to 4 per cent increase in productivity; in the higher temperature ranges, this percentage could be much higher.

Jan 1, 1981

By M. U. Özbay

A series of blasting experiments was carried out in an up-dip stope of a gold mine using short-perioddelay electric detonators. The main object of the investigation was to show the interactive effects of short-delay blasting. The delay range over which observations were made was restricted to between 10 and 200 ms. To quantify the blast results, data were collected on fragmentation, throw, position of muckpile, and ground vibration. For comparative purposes, blasting parameters for conventional pyrotechnic sequential firing were also measured. The paper describes the most relevant parts of the study and gives the experimental results. The interactive effects of short-delay blasting are analysed, and some aspects of the breaking mechanism are discussed.

Jan 1, 1985

By J. Dvorácek

Mine water poses a significant problem in lignite coal mining. The drainage of mine water is the fundamental prerequisite of mining operations. Under the legislation of the Czech Republic, mine water that discharges into surface watercourse is subject to the permission of the state administration body in the water management sector. The permission also stipulates the limits for mine water pollution. Therefore, mine water has to be purified prior to discharge. Although all mining companies operate mine water treatment plants, there is hardly any utilization of the final effluent. The high expenditure involved in the more sophisticated methods of mine water treatment has fuelled the search for the commercial utilization of the effluent.

Jan 1, 2012

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008

By A. S. Macfarlane

"SynopsisMetal accounting and reconciliation is an increasingly important governance issue in all mining operations, in that it is required, from a risk management perspective, that the company is in control of its product throughout the whole mining value chain. Reconciliation is a grossly misunderstood term. It means different things to different people, and therefore one of the purposes of this paper is to ensure a holistic and integrated understanding of ‘reconciliation’.Previously, where reconciliation was done, it was often for internal control purposes and loosely applied, sometimes with a low degree of confidence and understanding of the underlying parameters and their natural variability.In most mining operations, issues such as dilution, stope performance, and recovery are critical to profitability and long-term value, and thus understanding and control of these key value drivers is essential, not only from the governance perspective, but also from the perspective of maximizing shareholder returns. In order to implement a system for metal accounting and reconciliation, it is important that the cause and effect of these value drivers is understood, and that a systematic control system be established.While a number of off-the-shelf solutions exist for this work, it is the contention of this paper that a full understanding of the metal flow, its variability, its underlying loss potential, and its control points is necessary before a systematic approach to reconciliation can be undertaken.The paper also advocates that this approach should ensure that the reconciliation system clearly addresses the reconciliation needs, within a consistent framework. Such a framework has been developed by AMIRA, in terms of a metal accounting code. However, up until now, this code has been aimed at plant processes, whereas this paper shows how the concept can be extended to cover the full reconciliation requirements for a base metal mine.IntroductionReconciliation is defined as ‘the process of finding a way to make two different ideas, facts, etc., exist or be true at the same time’. In terms of a mining process, this refers to the comparison of measures and estimates along the value chain, and at different points in time, in order to track and optimize metal recovery. This leads to the notion of having a system in place for accounting for the metal. The University of Cape Town defines metal accounting as ‘… the estimation of (saleable) metal in a mine and subsequent process streams over a defined time period. Comparisons of estimates, from different sources over a specific time period, are called reconciliation.’Traditionally, metal accounting has consisted of geological reconciliations of mineral resource to mineral reserve conversion, mine planning reconciliation related to the reconciliation of long-term plans to short-term plans, grade control reconciliation of head grades to sampled or block grades, and mine survey reconciliation of tonnage discrepancies and mine call factors. In addition, metallurgical reconciliation has tended to be based on metal balancing, followed by some commercial metal accounting that links dispatched product to sales quality, quantities, and revenues. Miners disparagingly refer to this plant process as ‘millmatics’."

Jan 1, 2015

By L. Marais, S. Denoon-Stevens, J. Cloete

"Historically, mining companies worldwide provided housing and developed towns to accommodate their employees. At the end of the 1980s this approach became less prevalent and attempts were made to mitigate the effects of mine development and mine closure on communities living near the mines. Permanent settlement in mining towns urgently needed to be minimized. Since the advent of democracy, South African policy has moved in the opposite direction, shifting the emphasis to creating integrated communities and encouraging home ownership. Despite this policy shift, however, mines continue to influence local housing conditions. One direct outcome has been the development of informal settlements. We surveyed 260 informal settlement households in Postmasburg, a small and remotely located town in the Northern Cape Province of South Africa. We found that because they employ contract workers and thus arouse expectations of employment, the mines here contribute extensively to the development of informal settlements. But local factors also contribute, and the functional role of informal settlements as a form of housing that supports mobility should not be underestimated. We also found that both municipal and mining company policies for informal settlements were inadequate. Finally, we found that low-income informal settlers not associated with mine employment suffered the highest levels of social disruption.IntroductionA mine generates demand for labour, which in turn generates demand for housing. When settlements spring up near a mine this often means poor housing conditions. In South Africa in the 1960s and 1970s mining companies invested heavily in company towns or mining settlements, but they have become increasingly hesitant to do so, for three reasons. First, declining resource prices in the mid-1980s and the 1990s compelled them to focus on core business interests and reduce the costs of peripheral activities such as housing (Bryceson and MacKinnon, 2013); second, at the turn of the 20th century they were often accused of taking over the role of local government (IIED, 2002) and consequently became hesitant to invest in developing mining towns; and third, changing labour regimes also curbed their investment in such towns (Haslam McKenzie, 2010). Increasingly, the companies began to endorse block-roster shifts, and outsourcing also became more common in the early 1990s. Block-roster shifts in Australia (together with improved technology) have meant that miners do not need to settle near the mines but can fly in and fly out and have their urban houses as their stable homes. This has had serious negative implications for housing in remote towns in Australia, particularly worker camps, large-scale renting out of available accommodation, and ‘hot-bedding’."

Oct 1, 2018

By B. Nemutudi, X. Zhang, B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, S. Pikinini

The comparison study on adsorption of potassium normal butyl xanthate (PNBX) and sodium (nbutyl) dithiocarbamate (SNBDTC) on sperrylite mineral forms a basis in understanding the floatability improvement and paves a way for the design of collectors that may impact on a wide range of arsenide minerals. This study used a computational density functional theory (DFT) and experimental microcalorimetry approach to determine the adsorption energies of PNBX and SNBDTC collectors onto a sperrylite mineral surface. From a computational aspect, we considered the most stable surface plane of (100) surface, which had been found to give the lowest surface energy, compared to the other surface planes. It was observed that the PNBX and SNBDTC preferred to bridge on the As and Pt atoms through the S atoms. These findings showed that the collector adsorbed on the surface through both Pt and As atoms and indicated that the As atoms were significantly active in the adsorptions. We found that the adsorption energies were in the order: SNBDTC (–278.38 kJ/mol) > PNBX (–270.92 kJ/mol), indicating that the dithiocarbamate had stronger exothermic adsorption than the xanthate. From the microcalorimetry test it was also found that the SNBDTC was more exothermic than the PNBX and the adsorption energies were: SNBDTC (–473.50 kJ/mol) > PNBX (–331.13 kJ/mol). These results showed that the nitrogen atom in the SNBDTC collector had a great influence on the adsorption strength of the collector on the mineral surface. This is due to the electron deposition behaviour of nitrogen atoms compared to the electron withdrawing character of oxygen and as such the SNBDTC showed better collecting ability than the PNBX. These results paved the way for the design of collectors for sperrylite and other arsenide minerals and suggested that nitrogen in a collector may significantly improve the ability of the collector for improved recovery. Keywords: Computational modelling, microcalorimetry, SNBDTC and PNBX collectors, adsorption energies

Jan 1, 2020