Search Documents

By F. L. D. Cloete, M. C. Coetzee

This study was aimed at a comparison of the efectiveness of a new axial-flow type of mixer impeller (the Prochem design) with the traditional inclined-blade turbine. The intended application of the mixers was in carbon-in-pulp plants for the extraction of gold from cyanide-leached pulps. The first part of the project involved water and ion-exchange resin, and measurement of the power drawn by the various sizes of impeller to fully suspend the resin. The rate of reaction between the resin and the solution was measured as a function of the power input to the mixer. In the second part of the project, use was made of activated carbon, silver cyanide solutions, and ore pulps. The rate of absorption of silver from the solutions and pulps was determined, as well as the rate of attrition of the activated carbon caused by the various impellers in clear water. The Prochem design of axial-flow impeller was shown to fully suspend solids at only one-quarter of the power requireabyan inclined-blade turbine of similar size. The axial-flow pattern produced was responsible for the more uniform vertical concentration profile of suspended beads produced by the Prochem design. These measurements verified the observations of other researchers that the rate of reaction is not affected by the ;design of impeller provided that al the solids are fully suspended. The Prochem design of impeller therefore achieved the same reaction rate as the conventional turbine at a quarter of the power input. The atrition rates of activated carbon could be correlated, in terms of the energy absorbed, by the same equation for al the impellers. Higher concentrations of activated carbon increased the amount of carbon fines produced. These results emphasize the importance of designing mixers for minimum power consumption.

Jan 1, 1989

By P. Minkkinen, R. C. A. Minnitt

Particle size distribution analysis is important to many industries for assessing product quality, process efficiency, and compliance with contractual standards, while ensuring sample accuracy, and representativeness. Inaccurate particle size distribution results, arising from fines due to excessive handling can lead to penalties and buyer-seller disputes. A non-representative particle size distribution means samples will not accurately represent the chemical components either. Sampling blasthole cuttings poses challenges due to large material volumes, segregation, and uneven settling of particles in dense gold bearing ores. Commonly used sampling methods, such as spear or sectoral sampling, may lack representativeness. Particle size distribution analysis is crucial for evaluating sampling methods by comparing test sample representativeness against a reference standard derived from multiple particle size distribution analyses. Acceptable samples must fall within the 97.5% confidence intervals of the standard; deviations analyses lying outside these boundaries indicate a strong likelihood of segregation errors. A case study demonstrates this approach by using a 6.005 kg benchmark sample to assess two additional samples (1 kg and 5 kg), highlighting particle size distribution’s role in detecting sampling errors and refining protocols. An example of three test samples collected from reverse circulation drill cuttings compared to a standard reference sample is presented to illustrate a quality assurance/quality control procedure for reverse circulation drilling.

Oct 2, 2025

By G. R. Addie

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains a new method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007

By R. L. Castro

Currently, in several caving operations, the spacing between the drawpoints is determined by consulting Laubscher's design guide (Laubscher 1994, 2000), a methodology based on the gravity flow characteristics of the caved rock. Laubscher's methodology is based upon the height of interaction between adjacent flow zones, but does not allow calculation of primary recovery for a given layout. In this paper the authors present a technical and economic methodology based on the flow that occurs near the drawpoint and the associated development costs to estimate the optimal spacing. The flow model at the drawpoint was validated at the El Teniente mine, which extracts coarse caved rock. To validate the flow model, small-scale simulations using drawpoint clusters were conducted and results compared to extracted grades, marker recovery, and drill holes to determine ore remnants that are part of the production control programme at the mine. The results indicate that primary recovery depends on the height of interaction, which varies with the friction angle of the caved rock and the spacing between adjacent drawpoints. Primary recovery estimations indicate values from 85 per cent to 97 per cent depending on the drawpoint spacing used. Extrapolations were then conducted to estimate the primary recovery for different drawpoint configurations planned to be used in the New Mine Level of the mine. The results indicate that the optimal drawpoint spacing is 32 m x 20 m with a through length of 18 m. The methodology developed may be used to estimate optimal drawpoint spacing for block caving mines under different metal prices and mine cost conditions.

Jan 1, 2012

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d'une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l'aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L'ouverture, l'angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By G. J. C. Young

The new metallurgical plant has a simple, compact layout, being designed for a small team of operators. The reasons for building the new plant are given, and its various sections are briefly described. These include the conveyor plant, milling plant (for run-of-mine milling), thickener plant, agitator plant, filtration, clarification, smelthouse, and central core joining the mill and filtration sections.

Jan 1, 1978

By C G. Robinson, B. K. Loveday, J. C. Paynter

"A method of optimizing the design of a processing plant has been developed which minimizes capital and operating costs for average stripping ratios and ore characteristics. Models were developed to describe the operating characteristics and costs involved in various operations such as up-grading, leaching and solid-liquid separation.The options available in up-grading policy and the relation between the cut-off grade and the costs incurred subsequently in the treatment of the ore formed the basis of the optimization. To arrive at an optimum plant configuration and a set of operating parameters, the interrelation between grinding size, leaching temperature, leaching time, and various plant recycle options was investigated."

Jan 1, 2014

By M. M. Hajdasinski

The internal rate of return (IRR) is one of the most popular project evaluation criteria in the mineral industry, as well as in other industrial sectors. Analysis of its assumptions reveals, however, that this criterion does not function in the way it is supposed to. The search for a new criterion that would reflect the true rate of return (TRR) of an investment project or the true borrowing rate (TBR) of a borrowing project has led to the development of several approaches, yielding, for the same project, generally different values of the interest rate in question. Two of those approaches have been selected as the most representative and practical. Each has been presented in two variants, and subsequently analysed. As a result, it is shown that the various approaches to the TRR/TBR are all consistent with the net present value (NPV) criterion, and that each can serve as an independent project evaluation instrument, provided its assumptions can be regarded in a given situation as realistic enough.

Jan 1, 1987

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

By S. C. Everett, I. S. Schache, P. A. Bannister, G. F. Balderson

The Pooncarie Project is located in the Murray Basin region of Australia. This region is a potential new mineral sands province. Due to the geological environment and the lithology of the deposit, these deposits have some technical challenges that need to be addressed prior to their successful development. Within the Pooncarie Project the Ginkgo deposit will be developed first. The technical challenges it presents include its geographical isolation, the requirement to remove substantial quantities of overburden as well as the processing issues raised by the highly weathered nature of the ilmenite family of minerals. Ore characterization bench scale testwork and bulk sample pilot plant programmes have been carried out and the data obtained used to design flowsheets for both the wet plant and mineral separation plant circuits with the flexibility to enable these plants to handle the variable heavy mineral assemblage. In addition to the solving of the processing challenges, technical issues such as removal of overburden for the minimum unit cost, the use of hyper saline water in the dredge pond and the provision of infrastructure, have had to be addressed. None the less, the orebodies making up the Pooncarie Project have many positive features including low slimes content, good rutile and zircon grades and the ability to recover most of the ilmenite family of minerals into acceptable TiO2pigment feedstocks. The development of the project is set to proceed with the establishment of mining operations on the Ginkgo orebody feeding a mineral separation plant at Broken Hill. The initial shipment of products is expected to occur in early 2005.

Jan 1, 2003

By L. Zhou, J. Qiu, M. Tang, J. Wang, G. Dai

Coal spontaneous combustion in longwall gobs is a major concern in coal mines. In comparison to other hazards, this phenomenon is difficult to detect. Fifteen factors influencing coal spontaneous combustion in longwall gobs were identified from the literature. The logical relationships between these factors were evaluated and quantified by decision-making trial and evaluation laboratory (DEMATEL) and interpretive structural modelling (ISM) methods. A four-level hierarchical structure model was established. The research shows that combining DEMATEL and ISM can reveal the key factors that influence coal spontaneous combustion in longwall gobs and establishthe interactions and relationships among these factors. The results can provide the basis for preventing and controlling coal spontaneous combustion in longwall gobs.

Jun 10, 2024

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

YEAR 1943-1944 Vol. 44 Page A major change-over in the ventilation of a deep level mine, by F. G. Hill and E. C. Ranson, 27; Discussion 56, 62, 67, 71, 72, 79, 123, 129 131 A note on the quarrying of surface limestone in the Sinai Desert, by V. L. Bosazza.. .. 59 Mining with diamond drills at the Nkana Mine of the Rhokana Corporation, Limited, Northern Rhodesia, by W. A. Odgers and A. G. Stirling, 95; Discussion 117, 121, 122 123 On silicates and dusts from the Witwatersrand gold mines (some preliminary notes), by J. J. Frankel, 169; Discussion .. 178 Presidential Address-Review of the rock pressure problem, by C. Biccard Jeppe, 3; Discussion 11,15 17 The chemistry, production and application of plastics, by P. N. Lategan, 138; Discussion 151 153 YEAR 1944-1945 Vol. 45 Page A microtechnique for the size-grading of mine dust, by S. R. Rabson, 34; Discussion 49, 50, 52 55 Activated carbon for regenerating used lubricating oil, by F. J. Tromp and J. J. Matthee 90 A contribution to the study of the production of zeolites, by C. C. le Grange and A. J. Petrick 235 A laboratory method for the determination of the suitability of South African coal and coal blends for the manufacture of metallurgical coke, by R. F. J. Teichmann .. .. 202 Copper containing cements for self-sanitising surfaces, by R. S. Young and H. L. Talbot 156 Notes on some sulphide minerals from the Far East Rand, by E. Mendelssohn, 84; Discussion, 88 89 Presidential Address-A review of underground support on the Witwatersrand with its Bearing on the Problem of ultradeep mining, by P. J. Louis Bok, 3; Discussion, 24, 25 27 Scientific management with particular application to a Witwatersrand gold mine, by J. S. Ford, 63; Discussion, 77, 80, 82 83 Some aspects of rock-drilling practice (the Witwatersrand gold field), by C. J. Irving, 163; Discussion, 185, 190 *197 Temperature measurements in a mine on the Witwatersrand with an electrical resistance thermometer, by O. Weiss, 127; Discussion, 136 137 The measurement of the geo-thermic gradient by means of the clinical thermometer, by R. A. H. Flugge-de Smidt, 105; Discussion, 136 137 The micro-chemical determination of free and combined silica in mine dust, by S. R. Rabson, 43; Discussion, 49, 50, 52 55 The oxidation of pyrites associated with South African coals, by R. F. J. Teichmann 141 YEAR 1945-1946 Vol. 46 Page Air cooling plant, No. 4 Shaft, City Deep, Limited. A review of layout and results achieved, by H. W. Unwin, A. Malcolm and R. E. Campbell Pitt, 66; Discussion, 100, 102, 103, 106, 110 115 A preliminary note on the Waterberg coal field as a possible source of coking coal, by P. E. Hall 124

By S. M. Graham, G. Mellis

"The determination of the oxidation state(s) of an element present in a solid sample may be required for a number of reasons, including the assessment of the degree of reduction which has taken place during a multi-step production of a metal. In addition, possible flaws in a metal may result from small amounts of oxides included in the solid. The analyte of interest may be present as a major component of a sample of interest, or as a minor impurity - beneficial or requiring removal - in another matrix.Numerous methods have been established for the analysis of species in solution samples - for example, Fe2+ and Fe3+ by titration, Cr6+ by colourimetric means, etc. With appropriate knowledge of the solution being analysed, many of these methods are fairly straightforward, extremely reproducible and accurate. In those instances where the analyte in a solution is known to be in only one form, the analysis is even more straightforward, since it can be achieved instrumentally (by AAS, rCP-OES or rCP-MS, for example).However, the situation with respect to the analysis of solids is not as simple. Various techniques - such as X-ray diffraction - are routinely used by our mineralogists to obtain information about the various minerals present in solid samples, and thus about the oxidation states of the analyte elements present. However, these techniques usually give results that are qualitative, or semi-quantitative at best. They are also usually time-consuming and expensive. One of our colleagues at Mintek, Deshenthree Chetty, has done extensive work in developing a method for the quantification of manganese species in solids using mineralogical methods, and this is no small achievement."

Jan 1, 2014

By B. Mulcahy, M. Valenta

"The purpose of executing a project in a stagewise fashion is to evaluate all potential options in a cost-effective manner and develop an understanding of the project drivers, thereby minimizing overall project risk to the client. Among the more valuable tools for this exercise are production and financial models that can be used to quantify the sensitivity of the project to the critical parameters.The mine and concentrator used in this case study are located on the Kalahari Copper Belt, which extends from Zambia through northern Botswana into Namibia. This area of Africa has seen very little industrial development and the project will create much-needed employment and development in the region.The success of this project thus far can be attributed to the close cooperation between the geological, mining, and metallurgical disciplines. Regular updates of projected capital and operating cost estimates coupled with project outputs guided the teams in optimizing their various discipline models, ultimately delivering a compelling argument for the execution of the project. Key to the success was the development of a geometallurgical model for the prediction of concentrate tonnage, grade, and recovery for the life of the mine from the mining plan.This paper summarizes the metallurgical findings and the outcome of the various project stages. The development of the model is discussed, as are the challenges faced in developing a suitable metallurgical process route. IntroductionThe Kalahari Copper BeltThe Kalahari Copperbelt, which extends from Zambia across northwest Botswana into Namibia, is considered to be a broad time equivalent of the Central African Copperbelt, with a similar style of mineralization. However, at shallower depths (<25 m), chrysocolla and malachite exist in significant proportions in certain geological areas. As illustrated in Figure 1, the project is located in the Ghanzi-Chobe Fold Belt which forms part of the Kalahari Copper Belt. The Ghanzi Group, which overlies the lowest stratigraphic unit (the Kwebe Formation), consists of three formations, namely the Ngwako Pan, the D’Kar, and the Mamuno Formation (Hall, 2012)."

Jan 1, 2016

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015

By M. E. C. Snyman, N. Naudé

"Coal fines produced during processing are difficult to dewater and result in a lower quality product and consequent lower value. A South African coal mine experiences severe difficulties with belt filter dewatering operations due to the presence of fines reporting from the thickener underflows. Plant 2 currently handles super-fine particles of size -34 µm and has low belt filter efficiency: excessive moisture retention lowers the product quality and strains downstream processing. It was necessary to determine an alternative method for dewatering these fines. Blending of fine material with coarser material was proposed as a solution. The effect of coal particle size and layering during ultrafines belt filter dewatering was evaluated using various blends of the fine Plant 2 material with coarser Plant 1 material. The best layering arrangement of the two materials and its optimum blend required to achieve reduced filter cake moisture content was determined in practise using a vacuum filter to simulate belt filtration. A blend of the two materials gave improved dewatering efficiency for the belt filters compared with that of the Plant 2 material alone. The best layering configuration was with Plant 2 material at the bottom and Plant 1 material on top. The optimum blend for industrial applications comprised 48% fines from Plant 2. IntroductionFines are produced during the processing of coal. It is estimated that 2 to 3% of run-ofmine coal reports to the ultrafine portion (-100 µm) (le Roux, 2005). The particle size of coal is inversely proportional to the amount of water adsorption, so smaller particles adsorb more moisture. Moisture removal requires either mechanical processes or thermal drying: mechanical processes are less expensive, but the fines still have high moisture retention. Discarding of fines leads to economic losses, so it is essential that they be dewatered so that they can then be sold as a product: fines need to be treated for both resource management and conservation reasons (Kenney, 1994). Removal of free surface moisture from ultrafine coal particles using a belt filter therefore remains a process that needs to be continuously improved. Ultrafine coal originating from a thickener underflow is known to be difficult to dewater owing to factors such as filter cloth blockage and moisture retention due to clogging. Mixing of finer and coarser materials has been proposed to deliver better dewatering efficiency and improved the quality of the recycled water (Kenney, 1994)."

Mar 1, 2019

Papers and Contributions Since the Institute&apos;s inception, it had been our practice until some years ago to meet regularly for discussion of new developments, using as a basis a paper read by one of the members. Usually, the Journal issue containing the paper would have been circulated well before the meeting, giving members plenty of time to absorb it and perhaps to prepare contributions. Discussion was generally lively, often controversial. The author always had an opportunity to reply.

Jan 1, 1991

By S. J. Patchet

The use of fill in deep-level gold mining presents the possibility of achieving considerable economic and operational benefits if conventional support can be eliminated. Unfortunately, the combination of the properties of tailings from gold reduction plants and the narrow, flat, tabular reefs being exploited make conventional hydraulic filling very unpractical. Laboratory tests indicate that, with careful control of water content, these tailings can provide an adequate fill material. A variety of bonding agents have been investigated, and the most practical seems to be ordinary Portland cement. Even at very low cement contents some cohesion is achieved. The design and layout for a complete fill support system using hydraulic transport, dewatering, and pneumatic placement are discussed, and a surface field trial indicated that the principles involved are correct and that acceptable results can be achieved. This system and material would completely eliminate conventional timber and brick support, and a preliminary economic analysis indicates that filling is cost competitive on a direct replacement basis. All the operations for a full-scale operation are available or have been developed to a stage sufficient to indicate that the system is practical, although certain operations require further refinement.

Jan 1, 1978