Search Documents

By B. Talbot

How this simple plant generates a large revenue stream. The concept behind the Tailings Scavenging Plant (TSP) is simple: it is a non-complicated modular plant which is designed to be more stable than upstream plants. This, plus the use of ?high energy?, enables the plant to recover any metal missed by the upstream operation. Impala Platinum?Mineral process started pilot plant exercises in June 2003. The pilot plant ran for one year before the capital for the full-scale plant was approved. This year was used to motivate, design and cost a full-scale plant. The metal produced during the pilot and feasibility study enabled this part of the project to run at a small profit. The scale-up to full-scale was relatively simple as the pilot plant had a capacity of 180 m3/hrand the full-scale plant was designed for a capacity of 550 m3/h. The design for the full scale plant was completed in May 2003, with ground breaking taking place on 19 May 2003. The construction phase of the project went well with the commissioning of the first two modules taking place on 22 October 2003. The remaining two modules were commissioned two weeks later. The plant was at full capacity by the 20 November 2003. A review of the plants performance for the first 5 production months is as follows: the plant has required only a few minor modifications and additions, it has run well in excess of 95%availability with no major wear apparent. In addition to this, the plant has produced 3 times the metal forecast.

Jan 1, 2004

By Q. Li, B. Ricks

Over the last several decades mineral concentrate long distance slurry pipelines have been installed and successfully operated. Nearly all were installed via the buried construction method. Their record of depend ability and economy has been well proven. However, these systems operate in regions where seasonal soil frost penetration is shallow or non-existent. In recent years interest in long distance mineral concentrate pipelines in northern cold regions has been increasing. For cold regions one must consider seasonal temperatures and soil frost penetration in order to ensure reliable operations through the year. Herein a case study is developed where heat balance and temperatures for small and large diameter long distance slurry pipelines are compared. The study development is as follows: ?Rheological properties are analysed over range of temperatures from near freezing (4ºC; 39ºF) to relatively very warm (40ºC; 104ºF). ?Then assuming similar climatic conditions, soil properties, and pipeline length, a study is carried out for two pipeline diameters, namely: a small diameter (nominal8 inch; 219.1 mm) and a large diameter (22 inch; 558.8 mm). ?The study focus is on maintaining slurry temperature above freezing throughout the pipeline length by illustrating a decision based on burial depth versus coating the pipeline with insulation.

Jan 1, 2007

By M. R. Khalesi, Y. Kianinia, A. Seyedhakimi, F. Soltani

"The feed ore to Agh-Darreh gold processing plant (Takab City, Iran) contains 2 ppm Au, 7 ppm Ag, and 120 ppm Hg. After cyanide leaching of the feed at pH 10.4, 80% of the total mercury (in the form of cinnabar and metacinnabar) goes to the tailings dam. In this research, separation of mercury from the tailings by flotation was investigated. The effects of collector type and dosage, pH, and the number of cleaner stages were studied. The results showed that after two stages of cleaning a 40–62% recovery of Hg at a grade of 14.3% Hg is attainable. Recycle water from a test in which 50 g/t amyl xanthate and 30 g/t pine oil was used in the flotation stage showed no adverse effect on the leaching and adsorption of gold onto activated carbon.IntroductionMercury, most commonly found in the nature as the mineral cinnabar (HgS), is a hazardous substance because of its mobility and toxicity (Kyle et al., 2012). Roasting is the wellestablished treatment method for mercury ores, in which the sulphur is burned and volatilized and mercury recovered subsequently by cooling and condensation. However, for low-grade ores, flotation is mainly applied for primary concentration due to its comparatively low costs, low environmental hazards, and flexibility regarding feed variations (Bulatovic, 2007). Particularly, cinnabar can be easily recovered by flotation using pine oil and a collector such as xanthate (Bulatovic, 2007; Crozier, 1991). Floatability of cinnabar is reduced due to surface oxidation when it is exposed to the atmosphere after crushing. This problem can be eliminated by adding copper sulphate and lead nitrate or acetate. The best pH for cinnabar flotation is in the range of 6.5 to 8.5 according to Erspamer and Wells, (1954), who reported that cinnabar and stibnite can be floated with long-chain xanthate collectors and an alcohol frother, with cumulative recoveries of 97.8% and 94.7%, respectively. Lead acetate was used as an activator."

Jan 1, 2017

By J. Githiria, D. Wachira

The conventional truck and shovel haulage system has become expensive to operate in most mines due to current strict environmental conditions, increase in depth and size of open-pit mines, increase in labour costs, and fuel costs. These factors have motivated the search for alternative material haulage options in open-pit mines. In-pit crushing and conveying (IPCC) system has been regarded as a plausible alternative in material haulage systems. However, usage of IPCC has been limited to a few mines due to limited knowledge of IPCC performance, and other technical factors of the system. This paper investigates, and evaluates the productivity performance of four types of IPCC systems (fixed, semi-fixed, semi-mobile, and fully mobile IPCCs) using mine productivity index (MPi). Using a model developed by MATLAB, the MPi for the four systems is computed using input variables such as availability, utilisation, performance and number of trucks and shovels in a limestone quarry. The mine productivity index for fixed, semi-fixed, semi-mobile, and fully mobile IPCC is obtained as 67.13%, 69.02%, 70.52%, and 71.52% respectively. In conclusion, the fully mobile in-pit crushing and conveying system is the most appropriate IPCC in the quarry, due to its better productivity performance compared to the other three IPCC systems and the truck and shovel system currently in use.

Sep 1, 2021

By M. Gao

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2 (Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ? phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By M. Faure

The experiment with backfill at Harmony was mainly an attempt to improve the ground conditions in a particularly tricky section of the mine. A deslimed tailings system was selected for financial reasons, ease of installation, ease of operation and its low level of mechanization. The design of the system has three aspects: firstly, to define the parameters of the backfill material itself; secondly, to design a reliable plant which could consistently produce the desired material in sufficient quantities; and, thirdly, to design a fill distribution system for maximum reliability in the shaft, minimum pipe line velocity, pressure and cost in the horizontal sections and consistency and reliability at the delivery end. The system was successfully constructed and commissioned in a short space of time at a relatively low cost. It has now reached its full potential, and very encouraging results have been achieved with regard to cost savings, ground conditions, ventilation and accident statistics.

Jan 1, 1988

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI. However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI. In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

Grains are subject to contamination by mycotoxins which are metabolic by-products of various fungi. The fungal infestations produce local concentrations of the mycotoxins thousands of times higher than the average. These facts make the sampling of the grain for assessment of the mean mycotoxin levels potentially very difficult. In the context of sampling theory, this morphology of the infestations creates a very high distributional and intrinsic heterogeneity of the grain shipment. The distributions of mycotoxin concentrations in seaborne shipments that exist at loading and the number and intensity of infestations that develop under shipping conditions are unknown. All grain shipments carry spores that may give rise to mycotoxin-producing colonies; moisture and temperature determine the final extent of the problem. This paper develops the value of the sampling constant with respect to intrinsic heterogeneity based on data on observed Ochratoxin A (OTA) concentrations in individual wheat kernels. A useful relationship between the distribution of mycotoxin concentrations on a kernel to kernel basis and the distribution of concentration over subsamples is developed.

Jan 1, 2009

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By C. K. Chabedi

"This paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield. The resources occur at a depth greater than 250 m and the thickness of the coal is roughly 110 m, but the top 50 m comprises coal intercalated with shale and the bottom 60 m contains five seams with sandstone and shale partings. Various factors affecting multiple seam mining at these great depths are discussed with reference to lessons learned from local and international experience on multi-seam mining. Field geological and geotechnical data was utilized to assess the stability of the roof of the seams. There is no specific rock mass rating for the Waterberg area, therefore approximate coal mine roof rating (CMRR) values were used to propose appropriate support strategies. Analysis of Multiple Seam Stability (AMSS) was used to analyse the strength of the parting or interburden between the various seams, the mining sequence, and the interaction between the various seams.The research indicated that it is possible to mine seams with a low CMRR at high mining rates using longwall mining, although support for gateroads is expected to be expensive, time-consuming and onerous to install, and will impact gateroad development rates. It will not be possible to simultaneously mine zones in close proximity and failure of the interburden is predicted, thus dangerous mining conditions are anticipated. However, it will be possible to mine just two of the eleven zones using longwall mining. IntroductionThis paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield using bord and pillar and longwall mining. Figure 1 illustrates the location of the Waterberg coalfield relative to other coalfields in South Africa, while Figure 2 shows the areas containing deep and shallow resources. The Waterberg resources are expected to contribute to South Africa’s future energy requirements, and are currently exploited at the Grootegeluk open pit mine. Grootegeluk produces coal mainly for a power station, with the higher quality product supplied as metallurgical coal. The deposit is technically unique and challenging, being a multi-seam coal deposit with a total of 12 seams over a thickness of 110 m as shown in Figure 3, including Zone 5. There is currently limited knowledge on the multi-seam mining of the deep Waterberg resources. Multi-seam mining utilizing the bord and pillar method has been practised in South Africa before, but at a depth of less than 100 m in the Witbank coalfields. Multi-seam mining in thin seams has also been performed in the Natal coalfields at a depth of less than 160 m, but mostly using bord and pillar mining and secondary mining (partial pillar extraction)."

Jan 1, 2016

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By N. Sacks, N. B. S. Magagula, I. Botef

"Low-pressure cold gas dynamic spraying was used to deposit WC-4wt%Ni and WC-4wt%Ni-1wt%Mo coatings onto mild steel. Dense coatings with very low porosities were produced. No decarburization occurred during deposition and no deleterious phases were formed. The coatings were subjected to standardized material characterization tests, as well as slurry abrasion testing to assess their wear behaviour. The wear tests were conducted in synthetic minewater-silica slurries, while distilled watersilica slurries were used as a control. The hardness of the coatings, 512HV0.3 and 458HV0.3 for WC-4wt%Ni and WC-4wt%Ni-1wt%Mo respectively, are comparable to those achieved using high-temperature coating processes. The abrasion wear rates for both coatings were less than 5 mg/min and 10 mg/min in the distilled water-silica and synthetic mine water-silica slurries respectively. The approximately 50% increase in wear rate in the synthetic minewater slurry is attributed to a synergistic corrosive wear mechanism. The predominant wear mechanisms were identified as binder smearing and delamination, with carbide grain fracture and pull-out. IntroductionSlurry abrasion is a common phenomenon in mining operations, particularly in pipelines transporting, for example, sand-water slurries. This type of wear can cause pipeline fracture, shortened operational lifetimes, and impede pipeline efficiency. To reduce or limit abrasion, thermally sprayed tungsten-carbide-based coatings are often used as pipe linings (Kanchan et al., 2010). This is due to their attractive mechanical properties, which include high wear resistance, stiffness, hardness, compressive strength, and tensile strength. These properties are provided by the coating microstructure and composition, which is a blend of hard, wear-resistant tungsten carbide (WC) particles embedded in a fracture-tough metallic binder phase (Brookes, 1997). Cobalt (Co) is the most commonly used binder due to its excellent wetting of the WC phase and moderate mechanical properties; however, its application is limited to non-corrosive environments as it has a low corrosion and oxidation resistance (Andren, 2001). Nickel (Ni) may also be used as a binder, and has been shown to have superior oxidation and corrosion resistance, but in some applications may not have the required mechanical properties (Kim et al., 2006)."

Jan 1, 2016

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

By D. Van Dyk

Horizontal rotating mills are being used all over the world in different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions that are not always fully understood. Failures are therefore experienced, over time in the industry, which cannot always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyse these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyse the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating and the effect on the fatigue life of the mill gearing components, conditions are better understood, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2006

By G. A. Slabbert

The paper describes work undertaken to identify the influence of the matrix structure on the metal dusting rate of stainless steel alloys. Specifically, the difference in metal dusting rate between austenitic and ferritic stainless steels of similar chromium contents was investigated. The alloys were exposed to metal dusting conditions and their performance compared by weight loss, optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. The specific gas mixture used for all the tests were 18.9% CO-79.1% H2-2% H2O at 650°C. For austenitic stainless steels, Types 304, 321, 316, and 316Ti were compared to two ferritic grades, namely Types 430 and 441. The resistance of the ferritic grades was found to be significantly better than that of the austenitic grades. This was attributed to greater permeability of chromium through the matrix structure to maintain the protective oxide scale. The results will be used in the development of novel alloys to combat metal dusting.

Jan 1, 2013

By G. M. Evans, S. Mitra, A. V. Nguyen

As an alternative to the conventional flotation method, there has been continual research in an effort to enhance base metal ores and combustibles recovery using ultrasonics. These studies however were largely limited to the pre-treatment of ores for the removal of surface contaminants while the effect of ultrasonics on the bubble and pulp-phase interactions remained somewhat unexplored. Noting this deficiency, this study aimed to investigate the mechanistic effect of an ultrasonic field in an impeller less flotation cell specifically focusing on the bubble-particle interaction dynamics. A lab-scale flotation cell (capacity 1 litre) was designed, involving a vertically oriented ultrasonic probe (20 kHz, rated at 1.2 kW) and operated in the output power range from 1 to 20% with continuous liquid recirculation. Particle suspension was achieved by the combined action of recirculation and ultrasonic pulses. Interactions of coarse size glass ballotini particles (D32 = 314 μm) with bubbles (< 1 mm diameter) in the presence of a surfactant were studied, using high-speed imaging. Application of an ultrasonic pulse in the aqueous medium resulted in the generation of numerous microbubbles which increased with increasing input power and duration of the ultrasonic pulse time. Such periodic pulses introduced at a high level of turbulence in the pulp phase facilitated adequate bubble-particle contacts. Microbubbles played a key role in forming particle clusters which were observed to be floatable even in the absence of any carrier bubbles. When carrier bubbles were introduced, some of these particle clusters attached to the bubble surface and conveniently floated. It was noted that a favourable state of bubble-particle interaction was achievable to produce stable bubble-particles aggregates by suitably controlling the input power and period of the applied ultrasonic pulse. Keywords: Flotation, bubble-particle interactions, collision, attachment, detachment, ultrasonic pulse

Jan 1, 2020